MA750GQ-Z

MagAlpha MA750 Contactless Turning Knob Sensor Key features 8 bit digital and 12 bit PWM output 500 kHz refresh rate 7.5 mA supply current Serial interface for data readout and settings QFN16 3x3mm Package General Description The MagAlpha MA750 is a robust contactless angle encoder suitable for control buttons and knobs. The IC detects the absolute angular position of a permanent magnet, typically a diametrically magnetized cylinder attached to the rotor. The output is digital (SPI) or PWM. For usual potentiometer replacement, the PWM signal can be filtered to obtain an analog signal. Figure 1: Functional Block Diagram Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 1 MA750 Contactless Turning Knob Sensor 1. Specifications TABLE 1 OPERATING CONDITIONS Parameters Symbol Min Typ Max Unit Supply voltage VDD 3.0 3.3 3.6 V Supply current Isup 5.7 6.6 8.0 mA Supply voltage for OTP flashing Vflash 3.6 3.8 V Iflash 50 100 mA Operating temperature Top -40 125 °C Applied magnetic field B 30 150 mT Supply current for OTP flashing (1) (1) 75 See section 11 for more details about the supply circuit for OTP flashing. TABLE 2 SENSOR OUTPUT SPECIFICATIONS Measurement conditions: VDD = 3.3 V, 50 mT < B < 100 mT, Temp = -40 .. +125°C, unless otherwise noted Parameters Min Typ Max 4 6 ms +/- 0.7 +/- 1.5 +/-2.5 deg +/-0.005 +/-0.008 +/-0.05 deg/°C Power up time INL Unit Remark Output drift Temperature induced Magnetic field induced -0.005 -0.01 -0.025 deg/mT Voltage supply induced 0.0007 0.001 0.003 deg/mV Absolute output - serial Data output length 16 16 bit Refresh rate 500 520 550 kHz Latency 2 3 4 µs Resolution (3 noise level) 8 8 bit 12 12 bit Absolute output - PWM Resolution (3 noise level) Digital I/O Threshold voltage High 1.75 V Threshold voltage Low 1.05 V Rising edge slew rate 0.7 V/ns CL = 50 pF Falling edge slew rate 0.7 V/ns CL = 50 pF Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 2 MA750 Contactless Turning Knob Sensor 2. Timing of the Serial Interface The data link is a 4-wire serial bus, conmplying to the Serial Peripheral Interface (SPI) usual convention shown in Table 3 and Table 4. The MagAlpha sensor operates as slave. During one transmission a 16 bit word can be simultaneously sent to the sensor (MOSI pin) and received from the sensor (MISO pin). Note that it is possible to receive 24 bits of data (16 bits for the angle and 8 bits for a time index). See section 10 “Output Signals” for details. Figure 2: SPI Timing Diagram TABLE 3 SPI SPECIFICATION TABLE 4 SPI STANDARD SCLK idle state High CPOL 1 SCLK readout edge Rising CPHA 1 CS idle state High MODE 3 Data order MSB first DORD 0 TABLE 5 SPI TIMING Parameter Description Min Max tidle Time between two subsequent transmissions 20 ns tcsL Time between CS falling edge and SCLK falling edge 25 ns tsclk SCLK period 40 ns tsclkL Low level of SCLK signal 20 ns tsclkH High level of SCLK signal 20 ns tcsH Time between SCLK rising edge and CS rising edge 25 ns tMOSI Data input valid to SCLK reading edge 15 ns tMISO SCLK setting edge to data output valid 15 Unit ns Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 3 MA750 Contactless Turning Knob Sensor 3. Registers TABLE 6 REGISTER MAP Register address No Hex Bin 4 0x4 0100 9 0x9 1001 Bit 7 MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 LSB 0 0 0 Z(7:0) 0 0 0 1 0 The register 4 contains the zero position and the register 9 is used to flash the register 4. 4. Pin Configuration TABLE 7 PIN FUNCTIONS Figure 3: QFN-16 Top View No Name 1 N/C Function - 2 N/C - 3 N/C - 4 MOSI 5 CS Chip Select (Serial) 6 N/C - 7 MISO Data out (serial) 8 GND Ground 9 N/C - 10 N/C - 11 PWM PWM output 12 SCLK Clock (serial) 13 VDD 3.3 V supply 14 N/C - 15 N/C - 16 VFLASH Data in (serial) 3.6 V supply for OTP flashing Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 4 MA750 Contactless Turning Knob Sensor 5. Sensor – Magnet Mounting The sensitive volume of the MA750 is confined in a region less than 100 µm wide and consists of multiple integrated Hall devices. This volume is located, with a precision of 50 m in the center of the QFN package, both horizontally and vertically. The sensor detects the angle of the magnetic field projected in a plane parallel to the package upper surface. It means that the only magnetic field that matters is the in-plane component (X and Y components) in the package middle point. This detection mode gives flexibility for the design of an angular encoder: all the sensor needs is that the magnetic vector lies essentially within the sensor plane and that its amplitude is comprised between 30 and 150 mT. Note that the MA750 does work with smaller than 30 mT fields, but the linearity and resolution performance may deviate from the specifications (see Table 2). Figure 4: End-of-Shaft Mounting 6. Power Supply Decoupling For most applications, a single 100 nF bypass capacitor placed close to the supply pins sufficiently decouples the MA750 from noise of the power supply. If better decoupling is required, a larger capacitor (10 µF) can be added in parallel with the 100 nF, and/or a resistor (10) can be added between the supply line and the capacitor node. In any case, make sure that the connection between the MA750 ground and the power supply ground has a low impedance, in order to avoid noise transmitted from the ground. VFLASH needs to be supplied only when flashing the memory. Otherwise the VFLASH pin can remain unconnected or grounded (see Figure 5). Figure 5: Connection for Supply Decoupling Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 5 MA750 Contactless Turning Knob Sensor 7. Sensor Front-End The magnetic field is detected with integrated Hall devices located in the package center. The particularity of this sensor is that the angle is measured using the spinaxis method which directly digitizes the direction of the field without any ATAN computation or any feedback loop based circuit (interpolators, etc.). The spinaxis method is based on phase detection. It requires a sensitive circuitry generating a sinusoidal signal whose phase represents the angle of the magnetic field. The angle is then retrieved by a time-todigital converter, which counts the time between the zero crossing of the sinusoidal signal and the edge of a constant waveform (see Figure 6). The digitized time is the front-end output. number proportional to the angle of the magnetic field at the rate of 500 kHz. Zero Setting The zero position of the MagAlpha, , can be programmed with 12 bit of resolution. The angle streamed out, , is given by: , where is the raw angle, out of the front-end. The parameter Z(11:0), which is 0 by default, determines (see Table 8). This setting is valid for all output formats: SPI and PWM. TABLE 8 ZERO POSITION Z(7:0) Figure 6: Phase Detection Method. Top: Sine Waveform. Bottom: Clock of Time-to-Digital Converter. Zero position 0 0 1 1.41 … … 255 358.59 (deg) Looking further down the signal conditioning chain, it is crucial that the signal conditioning does not add unwanted phase shifts. For this purpose the MagAlpha incorporates an architecture where these shifts are automatically compensated, resulting in the stability displayed in Table 2. In short, the front-end delivers in a straightforward and open loop manner a digital 8. Programming the MA750 The MA750 incorporates one programmable register with 8 bit of memory to store the zero position setting. When the MA750 is powered up, each of these 8 bit of memory are set to the value zero, unless the register was previously stored in the One-Time-Programmable (OTP) memory. It means that during startup, the content of the OTP memory is copied to the registers. Once flashed the register content cannot be modified anymore. In order to set the content of the register, the user must send a digital stream composed of the 4-bit REGISTER WRITE command (0010), followed by a 4-bit register address and the 8-bit value to be sent to the register. The data stream, sent through the MOSI wire, is therefore 16 bits long: command 0 0 1 0 reg. address 0 1 0 0 MSB value LSB Once the command is sent, it will immediately be effective and will affect the next data sent from the MagAlpha. Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 6 MA750 Contactless Turning Knob Sensor Read back the register content It might be helpful to check the content of the register, for instance to verify that the programming was successful. The user must send the REGISTER READ command: 0001, then the 4-bit address of the register under test. The last 8-bit of the stream will be ignored. The user can send for instance 0000 0000: command 0 0 0 1 reg. address 0 1 0 0 The MagAlpha transmission. response value LSB 0 0 0 0 0 0 0 0 MSB is within the same Simultaneously the MagAlpha replies: Angle out A(7:4) A(3:0) MSB value Z(7:0) LSB In the first byte (simultaneous to the 4-bit READ command and the 4-bit address), the MagAlpha sends the 8 bits of the measured angle A(7:0). The second byte is the content of the register under test. After this transmission the MagAlpha will continue delivering the usual data. Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 7 MA750 Contactless Turning Knob Sensor 9. Output Signals The raw data coming out of the conditioning blocks is an absolute angle, between 0 and 360 deg. This angle is coded on 8 bits, depending on the value of AF. The absolute output is sent out digitally as serial data. The other outputs, ABZ or UVW, are constructed from the absolute angles. of 12 bits. The angle can be retrieved by measuring the on time. Since the absolute PWM frequency can vary from chip to chip or with temperature, accurate angle detection requires the measurement of the duty cycle, i.e. the measurement both the on time and the off time : Absolute - Serial The bit order of the transmitted data is MSB first, LSB last. The timing requirements are indicated in section 3. Every 2µs a new data is transferred into the output buffer. The master device connected to the MagAlpha triggers the reading by pulling the CS down. When a falling edge of the CS signal occurs, the data remains in the output buffer until the CS signal returns to logic 1. As the CS is low, the master can read the data by sending clock pulses with a maximum frequency of 25 MHz. Figure 8: Timing Diagram of the PWM Output Figure 7: Timing Diagram for Simple SPI Readout A full reading requires 8 clock pulses. The MA750 delivers: MSB LSB A(7:0) If the master triggers the reading faster than the refresh rate the MagAlpha may send several times the same data point. Note: the PWM output can also be used for obtaining a low frequency analog output. For this purpose the PWM signal must be low-pass filtered. Caution: the low-pass filter (with time constant ) will smear the zero angle transition. The transition width will be , where is the rotation speed. An analog signal, emulating a usual potentiometer can be constructed from the PWM output by low-pass filtering. See Figure 9 for a circuit example. The output is a voltage proportional to the angle, radiometric between the supply (VDD) and GND. Note that in tis example the supply must be larger than 3.3 V to correctly supply the MagAlpha. With such as circuit the zero position transition is smeared over ±0.02 deg around zero degree. Absolute - PWM The Pulse Width Modulation (PWM) output must be enabled before use, by setting the parameter PWM. When disabled the PWM pin has large impedance (tristate logic). This output provides a logic signal whose duty cycle is proportional to the angle of the magnetic field. The PWM frequency is close to 15.3 kHz (the nominal period is 65 s). The duty cycle is bounded by a minimum value (1/34 of the period) and a maximum value (33/34 of the period). See Figure 8. It means the duty cycle varies from 1/34 to 33/34, with a resolution Figure 9: Typical Circuit for Replacement of an Analog Potentiometer Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 8 MA750 Contactless Turning Knob Sensor 10. OTP Programming Example: set & flash the zero position at 50 deg The One-Time-Programmable (OTP) memory can permanently store the content of the programmable registers. The OTP memory is made of poly-silicon fuses. By activating the “flash” command the content of the entire register will be stored in the OTP memory. The flash command consists in setting some bits in the register 9. When the register 9 is set, the register 4 is stored permanently. It is possible to operate the MagAlpha without flashing the register 4. 1. Convert into binary: within a resolution of 8 bits, 50 deg is the binary number 00100011 (49.22 deg). 2. Store the zero position into register 4: command 0 0 1 0 3. reg. address 0 1 0 0 value LSB 0 0 1 0 0 0 1 1 MSB Read back the register 4 command 0 0 0 1 reg. address 0 1 0 0 value LSB 0 0 0 0 0 0 0 0 MSB If the programming was correct the MagAlpha replies with the register 4 content: Angle out A(15:12) A(11:8) value LSB 0 0 1 0 0 0 1 1 MSB 4. Connect the VFLASH pin to 3.6 V 5. Flash register 4: Figure 10: Circuit for Flashing The burning of the fuses during the flash process is irreversible: once a register is flashed the default values at power up will always be the same. After flashing the registers content cannot be modified anymore. Flashing procedure Prior to flashing, it is recommended to test the MagAlpha with the new settings and verify the performance of the sensor. command 0 0 1 0 6. reg. address 1 0 0 1 value LSB 0 0 0 1 0 0 0 0 MSB Disconnect the VFLASH pin from 3.6 V. Turn the MagAlpha off and on, and read back the registers 4 and 5 to verify that the flashing was successfully accomplished (steps 3 & 5). Once satisfied, the user can proceed with the flashing: - - Send the parameter to the register, and read back for verification. Tie the VFLASH pin to 3.6 V. Note: it is possible to supply both VDD and VFLASH with the same 3.6 V source. Set the register 9 to 0001 0000 Untie the VFLASH pin Then switch off and on and check by reading back the register content. Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 9 MA750 Contactless Turning Knob Sensor 11. Typical Characteristics Measurement conditions: VDD = 3.3V, Temp = 25°C, unless otherwise noted. Figure 11: Error Curve at Different Magnetic Fields. The INL is the Maximum Value of this Curve. Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 10 MA750 Contactless Turning Knob Sensor 12. Package Dimensions Package: Plastic Quad Flatpack No-lead QFN-16 3x3mm NOTES: 1. All dimensions are in mm 2. Package dimensions does not include mold flash, protrusions, burrs or metal smearing 3. Coplanarity shall be 0.08 4. Compliant with JEDEC MO-220 Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 11 MA750 Contactless Turning Knob Sensor 13. Ordering Information Part Number Package Free Air Temperature (TA) MA750GQ QFN 3x3mm -40° to 125° * For Tape & Reel, add suffix –Z (e.g. MA750GQ–Z). Appendix A: Definitions Resolution (3 noise level) The smallest angle increment distinguishable from the noise. Here the resolution is defined as 3 times , the standard deviation in degrees, taken over 1000 data points at a constant position. The resolution in bits is obtained with: 6 . Refresh rate Rate at which new data points are stored in the output buffer. Latency The time between the data ready at the output and the instant at which the shaft passes that position. The lag in degrees is , where is the angular velocity in deg/s. Power up time Starting at power up, time until the sensor delivers valid data. Integral Non-Linearity (INL) Maximum deviation between the sensor output and the best line fit. Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 12 MA750 Contactless Turning Knob Sensor 400 sensor out (deg) 350 300 lag 250 ideal sensor output 200 150 INL 100 0 sensor out best straight fit resolution ( ± 3 ) 50 0 100 200 300 400 500 600 700 rotor position (deg) Figure A1: Absolute Angle Errors Jitter For the incremental output maximum fluctuation of the angular position of the raising edges. Overall reproducibility Maximum variation between two readings, successive or not, of the same shaft position at a fixed magnetic field over the complete temperature range. Monolithic Power Systems, Inc. Switzerland www.sensimatech.com euroinfo@monolithicpower.com  +41 22 364 63 50 The information provided by Monolithic Power Systems, Inc. in this document is believed to be correct. However MPS reserves the right, without further notice, (i) to change the product specification and/or the information in this document and (ii) to improve reliability, functions and design of the product and (iii) to discontinue or limit production or distribution of any product version. Monolithic Power Systems, Inc. does not assume any liability arising out of any application or use of any product or information, including without limitation consequential or incidental damages. All operating parameters must be validated for each customer's application by customer's technical experts. Recommended parameters can and do vary in different applications. Devices sold by MPS are covered by patents and patent applications. By this publication MPS does not assume responsibility for patent infringements or other rights of third parties which may result from its use. Monolithic Power Systems, Inc. | Gland, Switzerland | Tel: +41 22 364 63 50 | euroinfo@monolithicpower.com | www.sensimatech.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2014 Monolithic Power Systems. All Rights Reserved. MA700 Rev 1.0 September 2014 13