MP6518GF-Z

MP6518 35V, 1.5A Stepper Motor Driver with Integrated MOSFETs The Future of Analog IC Technology DESCRIPTION FEATURES        The MP6518 is a stepper motor driver with a built-in micro stepping translator. It operates from a supply voltage of up to 35V and can deliver motor current up to 1.5A. The MP6518 can operate a bipolar stepper motor in full-, half-, quarter-, and eighth- step modes. Internal safety features include over-current protection, input over-voltage protection, UVLO and thermal shutdown. The part has a fixed 3.3V reference output, which allows it to operate without any control power supply and work with any microcontroller. Ron of the switches is as low as 300mΩ. Current sensing is done by external resistors. Wide 8V to 35V Input Voltage Range Two Internal Full Bridge PWM Converters Low On Resistance(HS:300mΩ; LS:300mΩ) No Control Power Supply Required Simple Logic Interface 3.3 and 5 V Compatible Logic Supply Full-, Half-, Quarter-, and Eighth- Step Functionality 1.5A Maximum Output Current Adjustable Mixed Decay Ratio Over-Current Protection Input OVP Function Thermal Shutdown and UVLO Protection Space-saving TSSOP-28-EP Package Fault Indication Output        The MP6518 comes in a space-saving TSSOP28 package with exposed thermal pad. APPLICATIONS     Bipolar Stepper Motors Printers Textile Machines Security Cameras All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION 3.3V 3P3VOUT 0.47uF CPB VIN nHOME 1uF MP6518 AOUT1 MS2 µC MS3 nENBL nSLEEP nRSET VREF Exposed GND PAD AOUT2 SENA SENA BOUT1 BOUT2 MDS ROSC 1uF VG STEP MS1 100nF VCP nFAULT DIR VIN CPA Motor SENB SENB 200kΩ MP6518 Rev. 1.11 8/22/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 1 MP6518 –35V, 1.5A MICROSTEPPING MOTOR DRIVER WITH INTEGRATED FET ORDERING INFORMATION Part Number* MP6518GF Package TSSOP-28 EP Top Marking See Below * For Tape & Reel, add suffix –Z (e.g. MP6518GF–Z) TOP MARKING MPS: MPS prefix: YY: year code; WW: week code: MP6518: product code of MP6518GF; LLLLLLLLL: lot number; PACKAGE REFERENCE TOP VIEW MP6518 Rev. 1.11 8/22/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 2 MP6518 – 35V, 1.5A MICROSTEPPING MOTOR DRIVER WITH INTEGRATED FETS ABSOLUTE MAXIMUM RATINGS (1) Supply Voltage VIN ......................... –0.3V to 40V xOUTx Voltage VA/BOUT1/2 ................ -0.7V to 40V VCP, CPB ................................... VIN to VIN+6.5V ESD Rating (HBD) ....................................... 2kV SENA, SENB ......................................... 700mV All Other Pins to AGND (Except for 3P3VOUT and VG) ................................................. -0.3V to 6.5V (2) Continuous Power Dissipation (TA = +25°C) ……………………………………………....3.9W Storage Temperature ............... -55C to +150C Junction Temperature ............................ +150C Lead Temperature (Solder).................... +260C Recommended Operating Conditions (3) Thermal Resistance (4) θJA θJC TSSOP-28 EP (9.7mmx6.4mm) ................................................ 32 ....... 6.... C/W Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD (MAX) = (TJ (MAX)-TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7, 4-layer PCB. Supply Voltage VIN .............................. 8V to 35V Output Current IA,BOUT................................ ±1.5A Operating Junction Temp. (TJ). -40°C to +125°C MP6518 Rev. 1.11 8/22/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 3 MP6518 – 35V, 1.5A MICROSTEPPING MOTOR DRIVER WITH INTEGRATED FETS ELECTRICAL CHARACTERISTICS VIN=24V, TA = +25°C, unless otherwise noted. Parameter Power Supply Input Supply Voltage Quiescent Current Voltage Regulator 3P3VOUT Reference Output Internal MOSFETs Symbol VIN ISLEEP VIN=24V; nENBL=0; nSLEEP=1, with no load VIN=24V; nSLEEP=0 V3P3 IOUT=1mA IQ RHS Output On Resistance RLS Body Diode Forward Voltage Control Logic Input Logic ‘Low’ Threshold Input Logic ‘High’ Threshold Condition VF Typ Max Units 8 24 35 V 7 10 mA 5 µA 3.3 3.45 V 0.30 0.35 Ω 3.2 VIN=24V, IOUT=1A, TJ=25°C VIN=24V, IOUT=1A, TJ=85°C VIN=24V, IOUT=1A, TJ=25°C VIN=24V, IOUT=1A, TJ=85°C IOUT=1.5A VIL All Logic Pins VIH All Logic Pins IIN(H) VIH=5V Logic Input Current IIN(L) VIL=0.8V R Internal Pull Down Resistance All Logic Pins PD nHOME nFAULT Outputs(Open-Drain Outputs) Output Low Voltage VOL IO=5mA Output High Leakage Current VO=3.3V IOH Protection Circuit VIN RISE UVLO Rising Threshold (5) VHYS UVLO Hysteresis VOVP Input OVP Threshold ∆V Input OVP Hysteresis OVP IOCP1 Sinking Over-Current Trip Level IOCP2 Sourcing tOCP Over-Current Deglitch Time(5) TTSD Thermal Shutdown(5) (5) ∆TTSD Thermal Shutdown Hysteresis MP6518 Rev. 1.11 8/22/2016 Min 0.32 0.30 Ω 0.35 0.32 2 -25 -8 Ω 1.3 V 0.6 V V µA µA kΩ 25 8 530 6.5 36 2.5 2.5 7 970 37.9 600 5.5 5.5 1 165 30 Ω 0.5 1 V µA 7.7 V mV V mV A A µs o C o C 40 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 4 MP6518 – 35V, 1.5A MICROSTEPPING MOTOR DRIVER WITH INTEGRATED FETS ELECTRICAL CHARACTERISTICS (continued) VIN=24V, TA = +25°C, unless otherwise noted. Current Control Constant Off Time Blanking time Crossover Dead Time VREF Input Current SENx Trip Voltage Current Trip Accuracy Charge Pump Frequency tOFF tBLANK tDT IREF VTRIP ∆ITRIP fCP Rt=200kΩ HS off to LS on or LS off to HS on for one bridge arm VREF=3.3V VREF=3.3V, 100% (no switch in test mode) VREF=3.3V, 70%-100% VREF=3.3V, 38%-64% VREF=3.3V, 19%-30% VREF=3.3V,