5962-80013

MIL-PRF-38534 CERTIFIED HIGH SPEED, FET INPUT DIFFERENTIAL OP-AMP M.S.KENNEDY CORP. 4707 Dey Road Liverpool, N.Y. 13088 0032 (315) 701-6751 FEATURES: Fast Slew Rate - 650 V/µS Typ. FET Input Wide Bandwidth Electrically Isolated Case Industry Wide Pin Compatible 0032 Upgrade DSCC SMD 5962-80013 DESCRIPTION: The MSK 0032 is a high speed, FET input, differential amplifier designed to replace the popular LH0032 and TP0032. Since the MSK 0032 requires less compensation than the LH0032, it exhibits wider bandwidth and greater stability. The MSK 0032 can be used as a direct replacement in current designs using the LH0032 or TP0032 with no changes to compensation schemes. High frequency signal transfer circuits such as video amplifiers, high speed integrators and comparators are just a few of the applications that the MSK 0032 is well suited for. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS Video Amplifiers Comparator Circuits High Speed Integrators 1 2 3 4 5 6 PIN-OUT INFORMATION No Connection Output Compensation Compensation/Balance Compensation/Balance Inverting Input Non-Inverting Input 1 7 8 9 10 11 12 No Connection No Connection No Connection Negative Power Supply Output Positive Power Supply Rev. C 9/06 ABSOLUTE MAXIMUM RATINGS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8 ELECTRICAL SPECIFICATIONS Parameter STATIC Supply Voltage Range 2 7 Quiescent Current VIN=0V 1 2,3 INPUT Input Offset Voltage Input Offset Voltage Drift Input Offset Adjust Input Bias Current Bal.Pins=N/C VIN=0V AV=-10V/V Bal.Pins=N/C VIN=0V RPOT=10KΩ To +VCC VCM=0V Either Input Input Offset Current VCM=0V 1 2,3 1,2,3 1 2,3 1 2,3 Input Impedance 2 Power Supply Rejection Ratio 2 Common Mode Rejection Ratio Input Noise Voltage 2 Equivalent Input Noise 2 OUTPUT Output Voltage Swing Output Current Settling Time to 1% 1 2 Test Conditions F=DC ∆ VCC=±15V F=DC VCM=±10V F=10Hz To 1MHz F=1KHz RL=1KΩ RL=1KΩ RL=1KΩ 10V step RL=1KΩ 10V step AV=+1 Settling Time to 0.1% 1 Unity Gain Bandwidth 2 TRANSFER CHARACTERISTICS Slew Rate Limit Open Loop Voltage Gain Small Signal Rise Time Small Signal Delay Time VOUT=±10V RL=1KΩ VOUT=±10V F=100Hz AV = +1 RL = 1KΩ VIN = 1V RL = 1KΩ NOTES: 1 2 3 4 5 6 AV=-1, measured in false summing junction circuit. Devices shall be capable of meeting the parameter, but need not be tested. Typical parameters are for reference only. Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4. Subgroup 5 and 6 testing available upon request. Subgroup 1,4 T A=TC=+25°C Subgroup 2,5 TA=TC=+125°C Subgroup 3,6 TA=TC=-55°C 7 Electrical specifications are derated for power supply voltages other than ±15VDC. 8 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cyle. ○ ○ ○ ○ ○ ○ ○ ○ RTH ±Vcc=±15V Unless Otherwise Specified Group A Subgroup MSK 0032B Min. Typ. Max. Min. MSK 0032 Typ. Max. Units ±10 - ±15 ±15 ±18 ±18 ±20 ±25 - ±15 ±15 - ±18 ±22 - - ±0.5 ±10 ±5 ±50 - ±1 - ±7 - Adjust to Zero 50 50 ±10 ±0.2 10 0.1 1012 70 80 1.5 40 ±100 ±50 25 25 45 45 - Adjust to Zero ±25 20 10 12 70 80 1.5 40 ±300 100 - - 4 4 4 4 - ±10 ±10 - ±12 ±20 0.1 300 25 0.5 - ±10 ±10 - ±12 ±20 0.1 300 25 0.5 - 4 4 4 4 350 70 - 650 10 12 20 25 350 70 - 650 10 12 20 25 2 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ TJ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ±VCC IOUT VIN TC ±18V Supply Voltage ±40mA Output Current ±30V Differential Input Voltage Case Operating Temperature Range -55°C to +125°C (MSK 0032B) -40°C to +85°C (MSK 0032) 200°C/W Thermal Resistance Junction to Case Output Devices Only ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ TST TLD Storage Temperature Range -65°C to +150°C Lead Temperature Range 300°C (10 Seconds) Junction Temperature 175°C V mA mA mV µV/°C mV pA nA pA nA Ω dB dB µVrms nV√Hz - V mA µS nS MHz - V/µS dB nS nS Rev. C 9/06 APPLICATION NOTES HEAT SINKING Since the case of the MSK 0032 only runs approximately 40°C hotter than the ambient temperature, a heat sink is generally not necessary. However, in applications where it is critical to minimize input bias current, a heat sink may be used.The case of the MSK 0032 is isolated from the internal circuitry so the heat sink may be attached directly to the case. The heat sink may however create enough parasitic capacitance at the pins to necessitate adjusting the amount of compensation used. COMPENSATION When replacing an LH0032 or TP0032 with an MSK 0032, no changes in compensation need be made. The MSK 0032 will demonstrate greater loop stability than the LH0032 and loop stability very similar to the TP0032. As with any operational amplifier, a feedback capacitor in the range of 2-10pF is recommended to compensate for the effect of the R-C time constant created by the input capacitance of the op-amp and the feedback and input resistors in an inverting configuration. See Figure 3 and Figure 4 for recommended compensation schemes for non-inverting configurations. INPUT OFFSET VOLTAGE NULL Figure 3 Figure 1 The input offset voltage of the MSK 0032 is typically less than ±0.5mV. If it is necessary to null the offset to zero or some value other than zero, the above circuit is recommended. Typical offset adjust range is 25mV. Figure 4 POWER SUPPLY BYPASSING Both the negative and the positive power supplies must be effectively decoupled with a high and low frequency bypass circuit to avoid power supply induced oscillation. An effective decoupling scheme consists of a 0.1 microfarad ceramic capacitor in parallel with a 4.7 microfarad tantalum capacitor from each power supply pin to ground. 3 Rev. C 9/06 Figure 2 Output Short Circuit Protection TYPICAL PERFORMANCE CURVES 4 Rev. C 9/06 MECHANICAL SPECIFICATIONS WEIGHT = 2.9 GRAMS TYPICAL ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED ORDERING INFORMATION Part Number MSK0032 MSK0032B 5962-80013 Screening Level Industrial MIL-PRF-38534, Class H DSCC-SMD M.S. Kennedy Corp. 4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent version of this datasheet. 5 Rev. C 9/06