K1570A

K1570A Series Applications: Phase-Locked Loops (PLL’s); Clock Recovery; Reference Signal Tracking; Synthesizers; Frequency Modulation/Demodulation 14-pin DIL Package 1.0 to 52.0 MHz Frequency Range 0.5V to 4.5V Control Voltage ±25ppm Stability -40°C to 85°C Operating Temperature This product is not recommended for new designs. Please refer to the MV product series. . x. Ma mm 0,7 2 ax mM 8m 3,0 1 5V Voltage Controlled Crystal Oscillators 0A Z K157.000 MH E CODE 46 TI DAT C mm 7,6 x. Ma PIN 1 E L E C T R I C A L S P E C I F I C AT I O N S Model Frequency Range (MHz) Input Current (mA) Frequency Control Function Deviation (ppm) Minimum Maximum Linearity (%) Modulation Bandwidth (±3dB) Nominal Control Voltage (V) Control Voltage Range (V) Transfer Function Input Impedance Frequency Stability (ppm) Overall 0oC to +70oC -40oC to +85oC Temperature Range (oC) Operating Storage Supply Voltage (V) Symmetry (%) CMOS/TTL Start Up Time (ms) Typical SSB Phase Noise (dBC/Hz) Offset from Carrier 10Hz 100Hz 1KHz 10KHz 100KHz -40oC to +85oC -55oC to +125oC +5.0V ±5% 40/60 20KHz 2.5 0.5 to 4.5 Positive > 50KΩ @ 10KHz K1570A 1 to 52 < 26 (For Custom Deviation Range, Vc Range, etc. - Consult Factory) PA R T N U M B E R I N G G U I D E K1570A XX - Specify Frequency “Blank” = 0°C to 70°C Operating Temp. “M” = -40°C to +85°C Operating Temp. “A” = ±25ppm (0oC to 70oC Op. Temp. Only “B” = ±50ppm 2553 N. Edgington Street, Franklin Park, IL 60131 P hone: 847.451.1000 F ax: 847.451.7585 800-888-1499 or www.champtech.com 1 Revision: 03-09-07 K1570A Series Voltage Controlled Crystal Oscillators This product is not recommended for new designs. Please refer to the MV product series. PIN 1 7 8 14 FUNCTION Voltage Control Gnd/ & Case Gnd Output + VCC SHIPPING TUBE CROSS SECTION OUTPUT WAVEFORM TEST CIRCUIT DIAGRAM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS Temperature Cycle Mechanical Shock Vibration Humidity Steady State Thermal Shock Electrostatic Discharge Solderability Hermeticity Resistance to Soldering Lead Integrity Marking Permanence Life Test REFERENCE PROCEDURES MIL-STD-833, Mtd 1010, Cond. B MIL-STD-883, Mtd 2002, Cond. B MIL-STD 883, Mtd 2007, Cond. B MIL-STD-202, Mtd 103 MIL-STD-883, Mtd 1011.7 Cond. B MIL-STD-883, Mtd 3015 Class II MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 DESCRIPTION -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell 1500 g’s 20-2000 Hz; 0.06 inch; 15g’s; 3 planes 40°C; 90%-95% R.H.; 56 days 100°C to 0°C; Water-to-Water; 15 cycles 2 KV to 4 KV Threshold Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He 240°C; 10 seconds: 1 inch/sec. MIL-STD-202, Mtd 210D, Cond. C MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum P hone: 847.451.1000 F ax: 847.451.7585 2553 N. Edgington Street, Franklin Park, IL 60131 800-888-1499 or www.champtech.com 2 Revision: 03-09-07