BLM18HG601SH1D

Spec. No. JENF243A-9104G-01 Reference Only P.1/9 GHz Noise Suppression Chip Ferrite Bead BLM18H□□□□SH1□ Murata Standard Reference Specification [AEC-Q200] 1. Scope This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM18H_SH Series based on AEC-Q200. 2. Part Numbering (ex.) BL (1) M (2) 18 (3) HG (4) 601 (5) (1)Product ID (2)Type (3)Dimension (L×Ｗ) (4)Characteristics (5)Typical Impedance at 100MHz S (6) H (7) 1 (8) D (9) (6)Performance (7)Category(for Automotive Electronics) (8)Numbers of Circuit (9)Packaging (D:Taping ) 3. Rating Customer Part Number MURATA Part Number Impedance () (Under Standard Testing Condition) (*1) (refer to below comment) at 1GHz at 100MHz BLM18HG471SH1D BLM18HG601SH1D BLM18HG102SH1D BLM18HD471SH1D BLM18HD601SH1D BLM18HD102SH1D BLM18HE601SH1D BLM18HE102SH1D BLM18HE152SH1D Rated Current (mA) 470±25% 600±25% 1000±25% 470±25% 600±25% 1000±25% 600±25% 1000±25% 1500±25% Typical 400 min. 450 min. 750 min. 700 min. 850 min. 1100 min. 300 min. 500min. 750min.  Operating Temperature : -55°C to +125°C 600 700 1000 1000 1200 1700 600 1000 1500 at at 125℃ 200 200 100 100 100 50 800(*2) 600(*2) 600(*2) 500(*2) 500(*2) 400(*2) 85℃ DC Resistance ( max. ) (*1) (refer to below comment) Initial Values Values After Testing 0.85 1.0 1.6 1.2 1.5 1.8 0.25 0.35 0.50 Remark 0.95 For 1.1 general 1.7 use 1.3 For 1.6 high speed 1.9 signal line 0.30 For 0.40 power line 0.55  Storage Temperature : -55°C to +125°C (*1) Standard Testing Conditions (Note) As for the Rated current marked with (*2), Rated Current is derated as right figure depending on the operating temperature.  In case of doubt  Temperature : 20°C±2 °C Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa R a te d C u rre n t ( A )  Unless otherwise specified  Temperature : Ordinary Temp. (15 °C to 35 °C ) Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Rated current at 85°C Rated current at 125°C 0 85 125 Operating Temperature (°C) MURATA MFG.CO., LTD. ESD Rank 1C:1kV 1C Spec. No. JENF243A-9104G-01 Reference Only P.2/9 4. Style and Dimensions 1.6±0.15 0.8±0.15 0.8±0.15 ■ Equivalent Circuit 0.4±0.2 ( : Electrode ) Resistance element becomes dominant at high frequencies. ■ Unit Mass (Typical value) 0.005g (in mm) 5. Marking No marking. 6. Specifications 6-1. Electrical Performance No. Item 6-1-1 Impedance Specification Meet item 3. 6-1-2 DC Resistance Meet item 3. Test Method Measuring Frequency : 100MHz±1MHz , 1GHz±1MHz Measuring Equipment : KEYSIGHT 4291A or the equivalent Test Fixture : KEYSIGHT 16192A or the equivalent Measuring Equipment : Digital multi meter *Except resistance of the Substrate and Wire 6-2. Mechanical Performance (based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June. 1 2010 No. Stress 3 4 High Temperature Exposure Temperature Cycling AEC-Q200 Test Method 1000hours at 125 deg C Set for 24hours at room temperature, then measured. 1000cycles -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. Murata Specification / Deviation Meet Table A after testing. Table A Appearance Impedance Change (at 100MHz) DC Resistance No damage Within ±30% Meet item 3. Meet Table B after testing. Table B Appearance No damage Impedance Within ±30% Change (BLM18HE (at 100MHz) Within±50%） DC Resistance 5 7 Destructive Physical Analysis Biased Humidity 8 Operational Life 9 External Visual Meet item 3. Per EIA469 No defects No electrical tests 1000hours at 85 deg C, 85%RH Meet Table B after testing. Apply max rated current. Apply 125 deg C 1000hours Meet Table B after testing. Set for 24hours at room temperature, then measured Visual inspection No abnormalities MURATA MFG.CO., LTD. Spec. No. JENF243A-9104G-01 Reference Only AEC-Q200 Stress Test Method Physical Dimension Meet ITEM 4 （Style and Dimensions） Resistance to Per MIL-STD-202 Method 215 Solvents Mechanical Shock Per MIL-STD-202 Method 213 Condition F 1500g(14.7N)/0.5ms/Half sine Not Applicable 14 Vibration 5g's(0.049N) for 20 minutes, 12cycles each of 3 orientations Test from 10-2000Hz. Meet Table A after testing. 15 Resistance to Soldering Heat 17 ESD Solder temperature 260C+/-5 deg C Immersion time 10s Per AEC-Q200-002 18 Solderability Per J-STD-002 No. 10 12 13 19 Electrical Characterization Murata Specification / Deviation No defects Meet Table A after testing. Pre-heating:150C +/-10 deg,60s to 90s Meet Table B after testing. Meet Table A after testing. ESD Rank:Meet Item 3. (Rating) Method b : Not Applicable 95% of the terminations is to be soldered. Measured : Impedance No defects 20 Flammability Per UL-94 Not Applicable 21 Board Flex Epoxy-PCB 1.6mm Deflection 2mm(min) 60s minimum holding time Meet Table A after testing. 22 Terminal Strength Per AEC-Q200-006 No defects 30 Electrical Transient Conduction Per ISO-7637-2 Not Applicable MURATA MFG.CO., LTD. P.3/9 Reference Only 2.0±0.05 4.0±0.1 4.0±0.1 1.75±0.1 7. Specification of Packaging 7-1. Appearance and Dimensions (8mm-wide paper tape) P.4/9 +0.1 1.85±0.1 3.5±0.05  1.5 -0 8.0±0.3 Spec. No. JENF243A-9104G-01 1.05±0.1 1.1max. (in mm) Direction of feed (1) Taping Products shall be packaged in the cavity of the base tape of 8mm-wide,4mm-pitch continuously and sealed by top tape and bottom tape. (2) Sprocket hole The sprocket holes are to the right as the tape is pulled toward the user. (3) Spliced point The base tape and top tape have no spliced point (4) Cavity There shall not be burr in the cavity. (5) Missing components number Missing components number within 0.025% of the number per reel or 1 pc., whichever is greater, and are not continuous. The specified quantity per reel is kept. 7-2. Tape Strength (1)Pull Strength Top tape Bottom tape 5N min. (2)Peeling off force of Top tape 0.1N to 0.6N (Minimum value is typical.) *Speed of Peeling off:300mm/min 165 to 180 degree Bottom tape Top tape F Base tape 7-3. Taping Condition (1)Standard quantity per reel Quantity per 180mm reel: 4000 pcs. / reel (2)There shall be leader-tape (top tape and empty tape ) and trailer- tape(empty tape) as follows. (3)On paper tape, the top tape and the base tape shall not be adhered at the tip of the empty leader tape for more than 5 pitch. (4)Marking for reel The following items shall be marked on a label and the label is stuck on the reel. (Customer part number, MURATA part number, Inspection number(1), RoHS marking(2), Quantity, etc) 1) « Expression of Inspection No. » □□ (1) (1) Factory Code (2) Date OOOO  (2) (3) First digit : Year / Last digit of year Second digit : Month / Jan. to Sep.  1 to 9, Oct. to Dec.  O, N, D Third, Fourth digit : Day (3) Serial No. 2) « Expression of RoHS marking » ROHS – Y (△) (1) (2) (1) RoHS regulation conformity parts. (2) MURATA classification number MURATA MFG.CO., LTD. Spec. No. JENF243A-9104G-01 Reference Only P.5/9 (5) Outside package These reels shall be packed in the corrugated cardboard package and the following items shall be marked on a label and the label is stuck on the box. (Customer name, Purchasing Order Number, Customer Part Number, MURATA part number, RoHS marking(2) , Quantity , etc) (6)Dimensions of reel and taping(leader-tape, trailer-tape) 7-4. Specification of Outer Case Label H D Outer Case Dimensions Standard Reel Quantity in Outer (mm) Case (Reel) W D H 186 186 93 5 Above Outer Case size is typical. It depends on a quantity of an order. W 8. ！ Caution 8-1.Rating Do not use products beyond the Operating Temperature Range and Rated Current. 8-2.Surge current Excessive surge current (pulse current or rush current) than specified rated current applied to the product may cause a critical failure, such as an open circuit, burnout caused by excessive temperature rise. Please contact us in advance in case of applying the surge current. 8-3. Fail Safe Be sure to provide an appropreate fail-safe function on your product to prevent from a second damage that may be caused by the abnormal function or the failure of our products. 8-4. Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1)Aircraft equipment (2)Aerospace equipment (3)Undersea equipment (4)Power plant control equipment (5)Medical equipment (6)Disaster prevention / crime prevention equipment (7)Traffic signal equipment (8)Transportation equipment (trains, ships, etc.) (9)Data-processing equipment (10)Applications of similar complexity and /or reliability requirements to the applications listed in the above MURATA MFG.CO., LTD. Spec. No. JENF243A-9104G-01 Reference Only P.6/9 9. Notice This product is designed for solder mounting. Please consult us in advance for applying other mounting method such as conductive adhesive. 9-1. Land pattern designing Standard land dimensions (Flow and Reflow soldering) Chip Ferrite Bead c a Solder Resist b Pattern Soldering Flow Reflow a 0.8 0.7 b 2.5 2.0 c 0.7 0.7 (in mm) 9-2. Soldering conditions Products can be applied to reflow and flow soldering. (1) Flux,Solder Flux Use rosin-based flux, but not highly acidic flux (with chlorine content exceeding 0.2(wt)%. ) Do not use water-soluble flux. Solder Use Sn-3.0Ag-0.5Cu solder Standard thickness of solder paste : 100 µm to 200 m (2) Soldering conditions Pre-heating should be in such a way that the temperature difference between solder and ferrite surface is limited to 150℃ max. Also cooling into solvent after soldering should be in such a way that the temperature difference is limited to 100℃ max. Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality. Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the deterioration of product quality. □Flow soldering profile Temp. (℃) 265℃±3℃ 250℃ Limit Profile 150 Heating Time Time. (s) 60s min. Pre-heating Heating Cycle of flow Standard Profile Standard Profile 150°C, 60s min. 250°C, 4s~6s 2 times Limit Profile 265°C±3°C, 5s max. 2 times MURATA MFG.CO., LTD. Reference Only Spec. No. JENF243A-9104G-01 P.7/9 □Reflow soldering profile Temp. (℃) 260℃ 245℃±3℃ 220℃ 230℃ Limit Profile 180 150 Standard Profile 30s～60s 60s max. 90s±30s Pre-heating Heating Peak temperature Cycle of reflow 9-3. Reworking with soldering iron Pre-heating: 150°C, 1 min Tip temperature: 350°C max. Soldering time : 3(+1,-0) seconds. Time. (s) Standard Profile 150°C~180°C, 90s±30s above 220°C, 30s~60s 245°C±3°C 2 times Limit Profile above 230°C, 60s max. 260°C, 10s 2 times Soldering iron output: 80W max.  Tip diameter:φ3mm max.  Times : 2times max. Note : Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the ferrite material due to the thermal shock. 9-4. Solder Volume Solder shall be used not to be exceeded as shown below. Upper Limit Recommendable t 1/3T≦t≦T (T:Chip thickness) Accordingly increasing the solder volume, the mechanical stress to product is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. MURATA MFG.CO., LTD. Reference Only Spec. No. JENF243A-9104G-01 P.8/9 9-5. Attention regarding P.C.B. bending The following shall be considered when designing and laying out P.C.B.'s. (1) P.C.B. shall be designed so that products are not subject to the mechanical stress for board warpage. a Products shall be located in the sideways direction (Length:ab) to the mechanical stress. b 〈 Poor example 〉 〈 Good example 〉 (2)Components location on P.C.B. separation. It is effective to implement the following measures, to reduce stress in separating the board. It is best to implement all of the following three measures; however, implement as many measures as possible to reduce stress. Contents of Measures (1) Turn the mounting direction of the component parallel to the board separation surface. (2) Add slits in the board separation part. (3) Keep the mounting position of the component away from the board separation surface. Perforation Stress Level A > D *1 A > B A > C C B D A Slit *1 A > D is valid when stress is added vertically to the perforation as with Hand Separation. If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid. (3) Mounting Components Near Screw Holes When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the tightening of the screw. Mount the component in a position as far away from the screw holes as possible. Screw Hole Recommended 9-6. Mounting density Add special attention to radiating heat of products when mounting the inductor near the products with heating. The excessive heat by other products may cause deterioration at joint of this product with substrate. 9-7. Operating Environment Do not use this product under the following environmental conditions, on deterioration of the Insulation Resistance of the Ferrite material and/or corrosion of Inner Electrode may result from the use. (1) in the corrodible atmosphere such as acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc. (the sea breeze, Cl2, H2S, NH3, SO2, NO2,etc) (2) in the atmosphere where liquid such as organic solvent, may splash on the products. (3) in the atmosphere where the temperature / humidity changes rapidly and it is easy to dew. MURATA MFG.CO., LTD. Spec. No. JENF243A-9104G-01 Reference Only P.9/9 9-8. Resin coating The impedance value may change and/or it may affect on the product's performance due to high cure-stress of resin to be used for coating / molding products. So please pay your careful attention when you select resin. In prior to use, please make the reliability evaluation with the product mounted in your application set. 9-9. Cleaning Conditions Excessive ultrasonic oscillation during cleaning can cause the PCBs to resonate, resulting in cracked chips or broken solder joints. Before starting your production process, test your cleaning equipment / process to insure it does not degrade this product. 9-10. Handling of a substrate After mounting products on a substrate, do not apply any stress such as bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the Product. Bending Twisting 9-11. Storage Conditions (1)Storage period Use the products within 6 months after delivered. Solderability should be checked if this period is exceeded. (2)Storage conditions Products should be stored in the warehouse on the following conditions. Temperature : -10°C to 40°C Humidity : 15% to 85% relative humidity No rapid change on temperature and humidity Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability.  Products should be stored on the palette for the prevention of the influence from humidity, dust and so on. Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. Avoid storing the product by itself bare (i.e.exposed directly to air). (3)Delivery Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 10 . ! Note (1)Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2)You are requested not to use our product deviating from the agreed specifications. (3) The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG.CO., LTD.