MPD6D11*S Specification
1
DC-DC Converter Specification
MPD6D11*S
1 . Application
This specification applies to DC-DC Converter MPD6D11*S(*:1∼9) for telecommunication /
data-communication equipment.
For any other application, please contact us before using this product.
2 . Customer Reference
Customer Spec. Number
Customer Part Number
3 . Customer & Murata Part Number
Nominal Output Voltage
1.2V
1.5V
1.8V
2.5 V
3.3V
5.0V
5.2V
12.0V
Customer Part Number
Part Number
MPD6D112S
MPD6D113S
MPD6D114S
MPD6D116S
MPD6D117S
MPD6D118S
MPD6D119S
MPD6D111S
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
2
P=2.54±0.2
Tolerance is not accumulated.
2
19
3
1 2 3 4 5 6
(4P)
6
10.3±0.2
5
MPD6D↑
31.2±0.5
4
18
17
16
15
14
13
12
11
10
(4.17) P
20
C
1
P P P P P P P P
US
Marking of No.1 pin
4.17±0.5
4 . Appearance, Dimensions
Objective Products
MPD6D11*S (*：1,2,3,4,6,7,8,9)
4.2max
37.3±0.5
39.9±0.6
Coplanarity Max 0.1
(in mm)
Marking
Part Number
MPD6D11_
(Omitted S of MPD6D11_S )
Murata CM Mark
Lot Number
1) Factory symbol
2) The last number of production year. Example:2 stands for 2002
3) Production month. Example:1 stands for:: January
9 stands for September
O stands for October
N stands for November
D stands for December
4)
5)
111,112,113,114,116,117,118,119 which is _ _ _ of MPD6D_ _ _S
6)
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
3
5 . Pin Number and Function
Pin No
Pin Symbol
1,10,
11,20
NCo
2
3
4
5
6
12
13
14
15
16
17
18
19
+Vout
+Vout
+Vout
-Vout
-Vout
ALM
RC
PO
NC
+Vin
+Vin
-Vin
-Vin
Function
Mechanical supplemental contact pins.
Pins at the four corners on printed circuit board.
To contact DC-DC Converter mounted board with
thermal setting resin.
(+)Output
(+)Output
(+)Output
( - )Output
( - )Output
Alarm Output
Remote On/Off Control
Parallel Operation
( + )Input
( + )Input
( - )Input
( - )Input
6. Block Diagram
6.1 Entire Product
+Vout
+V in
2
3
4
17
16
D R IV E
Filter
D R IV E
5
6
-Vout
19
18
14
-Vin
PO
C ontrol IC
RC
13
ALM
12
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
4
7. Environmental Conditions
7 .1 Operating Temperature Range
7 .2 Operating Humidity Range
7 .3 Storage Temperature Range
7 .4 Storage Humidity Range
-40°C ~ +85°C (With power derated.)
20% ~ 85% （No water condenses.）
-45°C ~ +90°C
10% ~ 95%( No water condenses.)
8. Absolute Rating
Item
Unit
Absolute Rating
V
0
Continuous
V
75
200µs
V
90
V
8
mA
10
Minimum Input Voltage
Maximum Input Voltage
ALM Applied VoltageRC
Applied Voltage
Time
PO Applied Voltage
Maximum ALM Sink Current
Remarks
Slew rate 42V/10µs
No voltage, no matter how instantaneous, shall be applied beyond the absolute maximum voltage rating to
this product.
If you apply any voltage over this limit, the product characteristics will deteriorate or the product itself will be
destroyed.
Even though it may continue operating for a while after the over-voltage event, its life will likely be shortened
significantly. Reliability and life of the module may degrade similarly if the maximum operating voltage rating
is continuously exceeded. This product is designed to operate within the maximum operating voltage rating
specification.
9. Characteristics
9 .1 Electrical Characteristics (Ta=25°C)
9 .1 .1 General Characteristics
Unless otherwise specified, (Ta= -40 to +85°C with power derated.)
Items
Unit
Value
Remark
Rated Input Voltage
V
48
Input Voltage Range
V
36 to 60
No powerderating with 0.2m/s(40LFM)
Turn-on Input
Voltage
Hysterisis Voltage
36 to 75
No powerderating with 0.5m/s(100LFM).
36 to 75
Powerderating with 0m/s(0LFM)
V
32.0 to 36.0
V
Minimum 2
Minimum 1500
Input voltage difference between turn-on
and turn-off
For one minute between input and output
Safty Standards
In accordance with CISPR
Publication22,Class A
(VCCI Class A)
UL60950(UL / C-UL)
Recognized
CE Marking
Attached
Self-declaration
Galvanic Isolation
Voltage
EMC (Radiated EMI /
Conduction)
Vdc
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
5
9 .1 .2 Specific Characteristics (Ta= -40 to +85°C with power derated.)
Models
MPD6D_ _ _S where _ _ _ is in below cells.
Items
Nominal Output Voltage
111
112
113
114
116
117
118
119
Unit
12.0
1.2
1.5
1.8
2.5
3.3
5.0
5.2
V
Output Voltage Regulation
Vin =36 to 75V
Output current range = 0 to
100%
+5%,-3%
%
Nominal Output Current
1.2
5.2
5.2
4.5
4.5
4.5
3.0
3.0
A
Output Current-limit
Inception
Min
1.23
5.35
5.35
4.63
4.63
4.63
3.09
3.09
A
Over Voltage
Protection : Note 1
Min
14.4
1.44
1.80
2.16
3.00
3.96
6.00
6.24
V
Low Voltage
Protection :Note 2
Max
10.8
1.08
1.35
1.62
2.25
2.97
4.50
4.68
V
Efficiency(typ.) Ta=25°C,
Vin = 48V, Nominal output
current
86
82
84
87
88
90
90
90
%
Output Ripple and Max
Noise
100
50
Note 3
mVp-p
Output Ripple
50
25
Note 3
mVp-p
Max
Note 1: Output halted in latch-up mode after mask time 0.5ms(typ.), which prevents DC-DC Converter
from malfunction by external noise and/or transient output voltage change.
Note 2: Output halted in latch-up mode after mask time 500ms(typ.), which prevents DC-DC Converter
from malfunction by external noise and/or transient output current change.
Note 3: Refer to 10.Measure Construction.
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
6
M PD6D112S (Vo=1.2V)
6
5
4
3
2
1
0
65°C
5.2A
3.4A
0.5 m /s or 0.2 m /s
0m /s
Output Current [A]
Output Current [A]
9-1-3-1 .Typical Power derating of MPD6D112S to MPD6D119S
Nominal output currents are attainable with 0.5m/s(100LFM),Vin=36to75V or
0.2m/s(40LFM ),Vin=36to60V. Powerderatings are required under 0m/s(0LFM),Vin=36to75V.
85°C
-40
0
40
6
5
4
3
2
1
0
80
Output Current [A]
0 m /s
Output Current [A]
2.9A
0 .5m /s o r 0 .2m /s
85°C
-40
6
5
4
3
2
1
0
65°C
4.5A
0
40
2.9A
0 m /s
85°C
40
Ambient Temperature [℃]
0m /s
85°C
0
40
Ambient Temperature [℃]
80
M PD6D116S (Vo=2.5V)
65°C
4.5A
2.9A
0.5m /s o r 0.2m /s
0m /s
85°C
0
40
80
Ambient Temperature [℃]
0 .5m /s o r 0 .2m /s
0
0.5m /s o r 0.2m /s
-40
65°C
4.5A
3.4A
3
2
1
0
80
M PD6D117S (Vo=3.3V)
-40
6
5
4
Ambient Temperature [℃]
80
Output Current [A]
Output Current [A]
M PD6D114S (Vo=1.8V)
65°C
5.2A
-40
Ambient Temperature [℃]
6
5
4
3
2
1
0
M PD6D113S (Vo=1.5V)
M PD6D118S (Vo=5.0V)
6
5
4
3
2
1
0
65°C
0 .5m /s o r 0 .2m /s
2.0A
0 m /s
85°C
-40
0
40
80
Ambient Temperature [℃]
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
Output Current [A]
7
MPD6D119S (Vo=5.2V)
6
5
4
3
2
1
0
65°C
0.5m/s or 0.2m/s
2.0A
0m/s
85°C
-40
0
40
80
Ambient Temperature [℃]
9-1-3-2 .Typical Power derating of MPD6D111S
Nominal output currents are attainable in Vin=36 to 60V or Vin=60 to 75V with various air flows
of 0.2m/s(40LFM),0.5m/s(100LFM),0.8m/s(160LFM),1.0m/s(200LFM).
Vin=36V to 60V
Vin=60V to 75V
1.44
1.44
1.20
Air Flow 1.0m/s
0.96
Air Flow 0.8m/s
0.72
Air Flow 0.5m/s
0.45
Air Flow 0.2m/s
Output Current [A]
Output Current [A]
1.20
0.24
0
-40
Air Flow 1.0m/s
0.72
Air Flow 0.8m/s
0.48
Air Flow 0.5m/s
0.24
Air Flow 0.2m/s
0
-20
0
20
40
60
80
100
-40
Ambient Temp(℃)
9-2.
0.96
-20
0
20
40
60
80
100
Ambient Temp(℃)
Operation Information
9-2-1. Reset Condition
In order to reset all function , the input voltage (Vin) is set under 5V for 1s. min.
Vin 36 to 75V
Reset Condition
5V min
1s.min
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
8
9-2-2. Over Voltage Protection (OVP)
The Isolated DC-DC Converter become into latch-up mode after typical 0.5ms. mask time,when the
output voltage is over the value specified in Over Voltage Protection(8.1.2) by failure of internal
control circuit. In order to reset, the input voltage is set under 5V for 1s. min. Output voltage might
exceed the point at which OVP starts to function under the specific condition of transient input
voltage or output current change. Therefore,OVP is set to wait for the mask time 0.5ms. It is
recommended to evaluate your appliances installed with the DC-DC Converter.
Vin 36 to 75V
Reset Condition
5V min
1s.min
9-2-3. Low Voltage Protection (LVP)
The Isolated DC-DC Converter becomes into latch-up mode after typical 500ms. mask time,when
the output voltage is under the value specified in Low Voltage
Protection(8.1.2) by operating Over Current-limit Inception due to failure of internal control or over
load. In order to reset, the input voltage is set under 5V for 1s. min.
9-2-4.
Remote On/Off Control
Vin 36 to 75V
Reset Condition
5V min
1s.min
The connection to a RC pin controls an Isolated DC-DC Converter to turn on/off.
While the Isolated DC-DC Converter is halted under the remote control, alarm function does not
operate;refer to Alarm Output.
Start
Halt
: RC is open or connected to -Vin
: RC is connected to +Vin
9-2-5. Alarm Output (ALM)
The Alarm Output can be down to the level of -Vin (Open Drain Output), when Over Voltage
Protection or Low Voltage Protection operates. Sink current in ALM pin is 10mA max. The Isolated
DC-DC Converter running for multiple and/or parallel operation are enable to simultaneously halt by
connecting all ALM pins, in the case of Over Voltage Protection or Low Voltage Protection caused
by any single DC-DC Converter. Maximum number running DC-DC Converters is 10pcs.
To connect more than 10,please consult Murata.
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
9
9-2-6.
Synchronous Turn-on/off
The Isolated DC-DC Converters running for multiple and / or parallel operation are enable to
synchronize turn-on/off timing among the running converters, of which the input voltage detection
circuits are unified to the detection voltage of a certain Isolated DC-DC Converter. Every PO pin is
necessary to be connected for multiple and/or parallel operation. Maximum number running DC-DC
Converters is 10pcs.To connect more than 10,please consult Murata.
9. 3 Reliability
9. 3. 1 Humidity Test
Parts are subjected to a temperature 40°C±2°C with 90∼95% for 100 hours.
Return the parts to room temperature (25°C) for 4 hours and measure. The initial values under item
9-1 should be met. (JIS-C-0022)
9. 3. 2 Thermal Cycle Test
Parts are subjected to 5 cycle of the following.
The parts are placed in room temperature (25°C) for 2 hours and are measured.
The initial values under item 9-1 should be met.
Step
Condition
1
2
3
4
-40±3°C
Room Temp.
+85±3°C
Room Temp.
Time
30 minutes
5∼10 minutes
30 minutes
5∼10 minutes
9. 3. 3 Vibration
10 to 55Hz, 1.5mm amplitude, 1 hour for each each of X,Y,Z directions.
No damage in appearance and no deviation from electrical characteristics(9-1).
9. 3. 4 Mechanical Shock
20G, 1 time for each X,Y,Z directions.
No damage in appearance and no deviation from electrical characteristics(9-1).
9. 3. 5 Soldering Heat Resistance
Immerse the part of lead where it is to be soldered on a motherboard in a solder bath of 260±5°C
for 3±0.5s.
Then tested products are left for 2 hours.
There is no damage in appearance and no deviation from electrical characteristics in clause 9.
9-3-6. Lead Pin Strength
Strain a lead pin by gradual-increasingly 5.0N along axial direction; withstand for 5s.
No damage on a lead pin.
9-3-7. Solderability of Leads
The lead pins will be immersed in the Isopropyl Alcohol (JIS K 1522) with Rosin (JIS K 5902)
solution (the concentration of Rosin will be allowed 10wt% to 35wt%, and normally approx.25wt%
will be used without any specific requirement.). Then the lead pins will be immersed in the solder
H63A (JIS Z 3282) solution at the temperature of 230°C±5°C for 3±0.5seconds, and pulled up
completely. The solder will adhere to over 75% of immersed area.
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
10
10. Measure Construction
10-1.Standard Test Circuit
Oscilloscope
A
A
Ein
V
RL
V
Isolated
DC-DC Converter
Ein
A
: Stabilized DC Power Supply
: Multimeter
V
RL
: Electronic or Resistive Load
10.1.1 Output Ripple & Noise
Coaxial cable:1.5D-2V(Refer to JIS C3501) ,1.5m length
+IN
Oscilloscope
fBW:500MHz
+OUT
C=10µF
Ceramic
capacitor
Ein
-IN
-OUT
Feedthru- termination
TRC-50F
Equivalent
by Keisoku Giken
schematic
R : 50Ω
C : 0.01µF
IN
OUT
Ceramic capacitor :10µF
(Connected output pins)
A
B
Coaxial cable
C
A: Output Ripple & Noise
B: Output Ripple
C: Switching Period
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
11
11. Packaging Information
11.1 Tray Dimensions
DC-DC Converters are put in the trays.
A-A' cross section
A
B
B'
A'
10.0
B-B' cross section
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
12
11-2. Maximum Pieces per a Tray.
18pcs/tray(except less than 18)
11-3. Package
Corrugated cardboard box contains trays with products.
Tray is heaped with alternately opposite direction to prevent products from contacting against the bottoms
of trays.
Dummy tray
Trays containing products
Bottom sheet of corrugated cardboard
Label
Corrugated cardboard box
Numerals in parentheses are reference only.
Unit : mm
Label ; written by
: Part Number,
: Quantity,
: Inspection Number,
: CE Marking.
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
13
12. Notice
12-1. Soldering
12-1-1. Flux
Please solder this product with Rosin Flux, which contains of 0.2wt%. or less chlorine.
Please do not use high activity acid flux or water soluble flux because they may erode metal or
glass portion of this product and may cause defectiveness or deterioration of this product.
12-1-2. Solder
Please use the solder H60, H63(JIS Z3282)or the equivalent type.
Please use the solder paste of equivalent type H60, H63.
12-1-3. Condition of Soldering
Reflow Solder
Reflow Soldering Profiles
JEDEC IPC/JEDEC J-STD-020D
Table 5-2 Classification Reflow Profiles
Pb-Free Assembly Large Body
Profile details
Soldering temperature
Soldering time
Heating time
Preheating time
Programming rate
Descending rate
Total soldering time
Time
：245 ºC +0/-5
：30 seconds,240∼245 ºC
：60∼150 seconds,217 ºC or more.
：60∼120seconds,150∼200 ºC
：3 ºC /sec.Max.,217∼245 ºC
：6 ºC /sec.Max.
：8 minutes Max.,25∼245 ºC
：Max 2 times.
Do not give vibration or an airing to product while solder melts under reflow process.
Please wait for products cooled down enough.
There is the possibility that products which are mounted on back side of motherboard
may fall down from the motherboard while reflow process.
Recommend to use supplemental mechanical contact to pins where is located at four
corners, by other adhesive methods, for example, a thermal setting resin, rather than
soldering.
Motherboard
Isolated DC-DC Converter
12-2. Cleaning
12-2-1. Please clean the products to remove flux by using the dip, boil, and vapor methods in isopropyl
alcohol for up to 5 minutes.
Please inform us if you are to use aqueous or semi-aqueous cleaning or other methods.
Do not use ultrasonic cleaning because semiconductor device on the products may be
damaged by resonance.
12-2-2. After cleaning, please dry the products thoroughly. If you touch the wet products ,the
marking on the products may be erased or blurred.
Do not measure electrical characteristics, until the products get dried enough.
12-2-3. If you don’t clean the products with no-cleaning type flux, you must confirm the
reliability of the products fully in advance.
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
14
12-3. Storage
12-3-1. Please store the products in room where the temperature/humidity is stable and direct sunlight
cannot come in ,and use the products within 6 months after delivery. Avoid damp heated places
or such places where there are large temperature changes, because water may condense on
the products, the characteristics may be reduced in quality, and/or be degraded in the
solderability. If you store the products for a long time (more than 1 year), use caution because
the products may be degraded in the solderability and/or rusty. Please confirm solderability and
characteristics for the products regularly.
12-3-2. Please do not store the products in the places such as : in a dusty place, in a place exposed
directly to sea breeze, in a place in an atmosphere containing corrosive gas (Cl2, NH3, SO2,
NOX and so on).
12-4. Operation Environment and Conditions
12-4-1. Operation Environment
The products are not waterproof, chemical-proof or rusts proof. In order to prevent leakage of
products and abnormal temperature increase of the products, do not use the products under the
following circumstances:
(1) in an atmosphere containing corrosive gas
(Cl2, NH3, SO2, NOX and so on)
(2) in a dusty place
(3) in a place exposed to direct sunlight
(4) in such a place where water splashes or in such a humid place where water
condenses.
(5) in a place exposed to sea breeze
(6) in any other places similar to the above (1) through (5)
12-4-2. Operation Conditions
Please use the products within specified values (power supply, temperature, input, output and
load condition, and so on). If you use the products over the specified values, it may break the
products, reduce the quality, and even if the products can endure the condition for short time, it
may cause degradation of the reliability. To insert fuse into input or Vin is recommended to
secure safety in any abnormality such as internal Isolated DC-DC Converter circuit broken down.
Please do not apply more voltage than one’s rated output from external circuit to output pins.
12-4-3. Handling
If you apply high static electricity over rated voltage or reverse voltage to the products, it may
cause defects in the products or degrade the reliability.
Please avoid the following items :
(1) over rating voltage apply, reverse voltage apply under measurement or not-enough
connection of 0 V(DC) line
(2) electrostatic discharge by production line and/or operators
(3) electrified appliances by electrostatic induction
Do not give an excessive mechanical shock.
If you drop the products on the floor, etc., it may crack the core of inductors and monolithic
ceramic capacitors.
Do not give strong shocks such as drops in handling.
Flexibility of products is limited up to 0.2mm as bending the substrate
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
MPD6D11*S Specification
15
12-5. Transportation
If you transport the products, please wrap-up in addition to the standard package. Otherwise
mechanical vibrations or mechanical shocks, may damage the package and please direct
transporters to handle with care. If you transport the products to overseas (in particular, by sea), it is
expected that the transportation environment will be the worst. So please pack the products, in the
package designed on the consideration of mechanical strength, vibration-resistant and
humidity-resistant. The package of the products, which Murata sells in Japan, may not resist over
seas transport. Please consult us if you are to use the standard package of the products sold in
Japan for transport to overseas.
13. Production Factories
Komatsu Murata Mfg.Co.,Ltd.
Wakura Murata Mfg.Co.,Ltd.
Kanazu Murata Mfg.Co.,Ltd.
Note
1.
2.
Against an unlikely event by abnormality or trouble of products, please give appropriate fail-safe
function to it to prevent secondary disaster.
Please contact our sales representatives or product engineers before using our products for the
applications listed below which require especially high reliability for the prevention of defects which
might directly cause damage to the third party's life, body or property.
1. Aircraft equipment
2. Aerospace equipment
3. Undersea equipment
4. Atomic power plant equipment
5. Medical equipment
6. Transportation equipment (vehicles, trains, ships, etc.)
7. Traffic signal equipment
8. Disaster prevention / crime prevention equipment
9. Data-processing equipment
10. Application of similar complexity and/or reliability requirements to the applications listed in
the above.
Request to customer
1. Please evaluate the products mounted on your appliance.
2. Contents specified in the document are based on the preconditions of the purpose, condition and
environment to which Murata has agreed with customers.
Please do not use the products deviated from application described in the specification.
3. Please return two specifications with stamped or signature for your receipt.
We consider it not appropriate to include other terms and conditions for transaction warranty in
product specifications, drawings or other technical documents. Therefore, if your technical
documents as above include such terms and conditions as warranty clause, product liability clause,
or intellectual property infringement liability clause, we will not be able to accept such terms and
conditions unless they are based on the governmental regulation or they are stated in a separate
contract agreement.
The document is for reference only and is subject to revision without notices.
Please contact Murata for formal documentation.
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.5.7
工商网监
湘ICP备2023018690号
