NMA2415SC

www.murata-ps.com s NOT RECOMMENDED NMA A 24V & 48V Series FOR NEW DESIGNSS Isolated 1WW Dual Output DC/DC Converters SELECTION GUIDE Order Code FEATURES Nominal Input Voltage V Output Voltage V NMA2405SC NMA2409SC NMA2412SC NMA2415SC 24 24 24 24 ±5 ±9 ±12 ±15 NMA2405DC NMA2409DC NMA2412DC NMA2415DC NMA4805DC NMA4809DC NMA4812DC NMA4815DC NMA4805SC NMA4809SC NMA4812SC NMA4815SC 24 24 24 24 48 48 48 48 48 48 48 48 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 „ RoHS compliant „ Efficiency up to 80% „ Power density up to 0.85W/cm3 „ Dual output from a single input rail „ UL 94V-0 package material „ No heatsink required „ Footprint from 1.17cm2 „ Industry standard pinout „ Power sharing on output „ 1kVDC isolation Output Current Efficiency mA % Isolation MTTF1 Package Capacitance Style pF kHrs Not recommended for new designs: ±100 70 39 ±55 77 85 ±42 80 65 ±33 80 95 Obsolete: ±100 70 39 ±55 77 85 ±42 80 65 ±33 80 95 ±100 70 26 ±55 80 38 ±42 80 52 ±33 80 56 ±100 70 26 ±55 80 38 ±42 80 52 ±33 80 56 194 129 134 101 194 129 134 101 206 174 139 104 206 174 139 104 SIP DIP SIP Recommended Alternatives (click for data sheet) MEA1D2405SC MEA1D2409SC MEA1D2412SC MEA1D2415SC MEA1D2405DC MEA1D2409DC MEA1D2412DC MEA1D2415DC MEA1D4805DC MEA1D4809DC MEA1D4812DC MEA1D4815DC MEA1D4805SC MEA1D4809SC MEA1D4812SC MEA1D4815SC When operated with additional external load capacitance the rise time of the input voltage will determine the maximum external capacitance value for guaranteed start up. The slower the rise time of the input voltage the greater the maximum value of the additional external capacitance for reliable start up. „ 24V & 48V input „ 5V, 9V, 12V and 15V output INPUT CHARACTERISTICS „ Internal SMD construction Parameter Conditions Min. Typ. Max. Units „ Fully encapsulated with toroidal magnetics Voltage range Continuous operation, 24V input types Continuous operation, 48V input types 21.6 43.2 24 48 26.4 52.8 V „ No external components required OUTPUT CHARACTERISTICS Min. Typ. Max. Units 1 W 1.2 15 10 150 %/% Parameter DESCRIPTION The NMA series of DC/DC converters are the standard buliding blocks for on-board distributed power systems. They are ideally suited for providing dual rail supplies on primarily digital boards with the added benefit of galvanic isolation to reduce switching noise. All of the rated power may be drawn from a single pin provided the total load does not exceed 1 watt. Rated Power2 Voltage Set Point Accuracy Line regulation Load Regulation Ripple and Noise Conditions TA=0°C to 70°C See tolerance envelope High VIN to low VIN 10% load to rated load, 5V output types 10% load to rated load, all other output types BW=DC to 20MHz, all input types % mV p-p ABSOLUTE MAXIMUM RATINGS Lead temperature 1.5mm from case for 10 seconds Internal power dissipation Input voltage VIN, NMA24 types Input voltage VIN, NMA48 types 300°C 450mW 28V 54V 1. Calculated using MIL-HDBK-217F with nominal input voltage at full load. 2. See derating graph. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified. 　 For full details go to www.murata-ps.com/rohs www.murata-ps.com/support KDC_NMAC2.G02 Page 1 of 4 NMA 24V & 48V Series Isolated 1W Dual Output DC/DC Converters ISOLATION CHARACTERISTICS Parameter Conditions Min. Isolation test voltage Resistance Flash tested for 1 second Viso= 500VDC 1000 10 Parameter Conditions Min. Switching frequency All input types Typ. Max. Units VDC GΩ GENERAL CHARACTERISTICS Typ. Max. Units 100 kHz TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Specification Storage Cooling All output types 0 -55 Typ. Max. Units 70 150 °C Free air convection RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions NMA series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second. A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?” For a part holding no specific agency approvals, such as the NMA series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. The NMA series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%. www.murata-ps.com/support KDC_NMAC2.G02 Page 2 of 4 NMA 24V & 48V Series Isolated 1W Dual Output DC/DC Converters PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS - 14 PIN DIP SIP package DIP package 0.77 (19.50) 0.385 (9.80) 0.77 (19.50) NMA2405DC Pin Function 1 -VIN 7 NC 8 OV 9 +VOUT 11 -VOUT 14 +VIN 0.236 (6.00)** XYYWWi 0.394 (10.00) 0.268 (6.80)* NMA2405SC 0.022 (0.55) 0.0178 (0.45) XYYWWi PIN CONNECTIONS - 7 PIN SIP 1 0.181 (4.60) 0.142 (3.60) 2 0.181 (4.60) 0.141 (3.60) 0.043 (1.09) 1 11 0.0118 (0.30) 0.0079 (0.20) 9 8 TEMPERATURE DERATING GRAPH 0.05 (1.25) 0.5 (12.70) 2 -VIN 4 -VOUT 5 OV 6 +VOUT Weight: 2.4g (24V DIP) 2.9g (48V DIP) 2.2g (24V SIP) 2.9g (48V SIP) TOLERANCE ENVELOPE 1.5 +10% 1.0 +5% VNOM 70°C 0.5 Safe Operating Area 125ºC 50 100 Ambient Temperature (ºC) 150 Output Voltage Output Power (W) +VIN 0.0118 (0.30) 0.0079 (0.20) 0.6 (15.24) 0 Function 1 0.22 (0.55) 0.0178 (0.45) 0.079 (2.00) * 0.303 (7.70) for 48V variants ** 0.295 (7.50) for 48V variants All dimensions in inches ±0.01 (mm ±0.25mm). All pins on a 0.1 (2.54) pitch and within ±0.01 (0.25) of true position. 0 Pin 7 0.3 (7.62) 0.084 (2.13) 0.1 (2.54) 0.1 (2.54) 0.022 (0.55) 0.0178 (0.45) 14 4 5 6 Typical L oad Line +2.5% -2.5% -7.5% 10 75 50 25 Output Load Current (%) 100 The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading. www.murata-ps.com/support KDC_NMAC2.G02 Page 3 of 4 NMA 24V & 48V Series Isolated 1W Dual Output DC/DC Converters PACKAGE SPECIFICATIONS (continued) RECOMMENDED FOOTPRINT DETAILS 14 Pin DIP Package 0.045 (1.15) Ø 0.039 (1.00) 5 HOLES 7 Pin SIP Package 0.045 (1.15) Ø 0.039 (1.00) 5 HOLES 0.00394 (0.1) 0.00394 (0.1 0.1 (2.54) 0.1 (2.54) 0.1 (2.54) 0.1 (2.54) TUBE OUTLINE DIMENSIONS 7 Pin SIP Tube 14 Pin DIP Tube 
 


 
 
 




 

Unless otherwise stated all dimensions in inches (mm) ±0.5mm. Tube length (14 Pin DIP) : 20.47 (520mm ±2mm). Tube length (7 Pin SIP) : 20.47 (520mm ±2mm). Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED 

Tube Quantity : 25 This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2011 Murata Power Solutions, Inc. www.murata-ps.com/support KDC_NMAC2.G02 Page 4 of 4