LBWA1ZZVK7-539

Preliminary Specification Number : SP-ZZVK W-LAN Module Data Sheet 802.11b/g module Product Part Number: LBWA1ZZVK7-539 Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 1/23 Revision History Revision Code Date 2011/11/29 First Issue Description Comments Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Notice for Murata Wireless Modules. Please read the specification including the NOTICE (Page20) and the Disclaimer (Page24) in this datasheet before using the Murata Wireless Modules. Preliminary Specification Number: SP-ZZVK P. 2/23 Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 3/23  Module Features  Murata LBWA1ZZVK7 module integrates WLAN function.  WLAN: IEEE 802.11 b, g, compliant.  Typical WLAN Transmit Power (typical): +19.5dBm at 11Mbps, CCK (11b) +15.0dBm at 54Mbps, OFDM (11g)  Typical WLAN Sensitivity (typical): T.B.D at 8% PER, 11Mbps T.B.D at 10% PER, 54Mbps  Module size: 16.5x11.5mm typical.  Module height: 2.2mm max.  FCC (USA) and IC (Canada) Certification will be supported with mono-pole type antenna.  Murata LBWA1ZZVK7 module consists of the following components - Texas Instruments CC3000 SoC – WLAN baseband and RF converter - Clock sources – Both Fast Clock and Slow Clock are integrated. - Front End Module – A combination of PA and a switch - Band Pass Filter – Filtering out of band noise and interference - EEPROM – A non volatile memory - Power FET switch – minimizing leakage current in shutdown mode. The switching mode power source provides 3.3V supply for the CC3000 from either battery or MCU the board. - Level Shifter – Supporting 1.8V and 3.3V Host Interface.  Seamless integration with several Texas Instruments MSP430 and Stellaris processors  SPI host interface for WLAN  RoHS Compliance Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 4/23 Scope This specification is applied to the IEEE802.11 b/g WLAN module. Host Interface - W-LAN IC/Firmware - W-LAN BB/MAC - FEM for CC3000 Reference Clock Sleep Clock Weight MSL RoHS Compliant 1 Part Number Part Number 2 Block Diagram LBWA1ZZVK7-539 : SPI : CC3000 : TriQuint TQM679002A (E2.6) : 26MHz Reference Clock is integrated. : 32.768kHz oscillator is integrated. : T.B.D (mg) : Level3 X’tal Osc. (26MHz) CC3000 (RF/BB/MAC) RF Front End 2.4GHz Level Shifter LDO Sleep CLK SPI BPF LDO EEPROM DC-DC Converter FET VBAT ENABLE Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 5/23 3 Dimensions and Terminal Configurations L T c2 c1 a2 a3 a1 W e3 e4 b5 b1 b2 e1 b3 e2 b6 c3 Mark L a1 b1 b4 c1 e1 e4 Dimensions 16.5 +/- 0.2 0.6 +/- 0.1 0.3 +/- 0.2 0.3 +/- 0.2 1.0 +/- 0.1 1.0 +/- 0.1 1.5 +/- 0.1 Mark W a2 b2 b5 c2 e2 - Dimensions 11.5 +/- 0.2 0.6 +/- 0.1 0.45 +/- 0.200 1.95 +/- 0.20 1.0 +/- 0.1 1.6 +/- 0.1 - Mark T a3 b3 b6 c3 e3 - (unit: mm) Dimensions 2.20 Max 0.6 +/- 0.1 3.15 +/- 0.200 3.0 +/- 0.2 1.0 +/- 0.1 1.0 +/- 0.1 - Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. b4 Preliminary Specification Number: SP-ZZVK P. 6/23 Terminal configuration No. Terminal Name Type Power System Connection to IC Terminal Description 1 2 3 GND ENABLE GND I - - - FET FET LDO Level Shift er 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 FET Ground Module Enable Power Supply Input Ground 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 VBAT GND GND GND GND WL_RS232_RX WL_RS232_TX WL_EN1 UART_DBG WL_EN2 GND GND GND GND SPI_CLK SPI_DI GND SPI_CS SPI_DO SPI_IRQ GND GND GND FUNC5/NC I I/O I/O I IO IO IO IO IO IO - WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN - FET LDO Level Shifter RS232_Rx RS232_Tx WL_EN WL_UART_DBG BT_EN SPI_CLK SPI_DIN SPI_CS SPI_DOUT SPI_IRQ NC Power Supply Input Ground Ground Ground Ground Connect to FUNC2 pin with 2kohm resister. RS232_Tx Connect to WL_EN2 Logger Connect to WL_EN1 Ground Ground Ground Ground SPI Clock from the host SPI Data-in from the host Ground SPI Chip select SPI Data-out from the host SPI Interrupt Request Ground Ground Ground NC - Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 ~ 76 SCL SDA NS_URAT_DBG FUNC4 FUNC2 GND GND SDA_EEPROM SCL_EEPROM GND GND GND GND GND GND GND 2.4G_ANT GND GND GND GND GND - - Preliminary Specification Number: SP-ZZVK P. 7/23 I2C to EEPROM 3000 SCL Connect to SCL_EEPROM pin I2C to EEPROM 3000 SDA Connect to SDA_EEPROM pin 3000 3000 Moe mory Moe mory 3000 NS_UARTD FUNC2 EEPROM EEPROM NC (D) Networking subsystem UART Debug line Connect to WL_RS232_RX pin with 2kohm resister. Ground Ground Connect to SDA pin Connect to SCL pin NC Ground Ground Ground Ground Ground Ground RF transmitter output and RF receiver input IO IO - - - I/O - - WLAN - - - Ground Ground Ground Ground Ground Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 8/23 4 Rating Parameter Storage Temperature VBAT Supply Voltage ENABLE min. -40 -0.5 -0.5 max 85 4.5 4.5 unit deg.C V V 5 Operating Condition Parameter Operating Temperature VBAT Supply Voltage ENABLE min. -30 2.7 1.65 typ. 25 3.6 1.8 max 70 4.5 1.95 unit deg.C V V 6 Input/Output Terminal Characteristic min. max unit VIH：High-level input voltage VIL：Low-level input voltage VOH：High-level output voltage VOL：Low-level output voltage 2.0 VBAT 0 0.8 VBAT V V V V Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 9/23 7 WLAN Power Up/Down Sequence 7.1 Power Up Sequence The following sequence describes device powerup from shutdown. ENABLE starts the initialization sequence, and subsequent events are automatic. Power up requirements: 1. No signals are allowed on the IO pins if no IO power supplied, because the IOs are not 'failsafe'. Exceptions are SLOWCLK, XTALP and which are failsafe and can tolerate external voltages with no VDDS and DC2DC. 2. VBAT , VIO, and SLOWCLK must be stable before releasing EN. The LBWA1ZZVK7 module should activate the power on with only one control enable line from the MCU. Below is the wake up sequence. WL_EN1/WL_EN2 7.2 Power Down Sequence WL_EN1/WL_EN2 Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 10/23 8 HOST Interface 8.1 Host interface: SPI 8.2 SPI Interface timing 8.2.1 SPI Clock Switching Characteristic PARAMETER Clock frequency,CLK Low/High duty cycle Pulse duration, CLK low Pulse duration, CLK high Rise time, CLK Fall time, CLK Setup tim e, input valid before CLK↑ Hold tim e, input valid after CLK↑ Delay tim e, CLK↓ to output valid Delay tim e, CLK↓ to output invalid MIN 0 40 5 5 MAX 48 60 UNIT MHｚ % ns ns ns ns ns ns ns ns fclock DC tWL tWH tTLH tTHL tISU tIH tODLY1 tODLY2 CL CL CL CL CL CL CL CL CL CL ≦10pF ≦10pF ≦10pF ≦10pF ≦10pF ≦10pF ≦10pF ≦10pF ≦10pF ≦10pF 4.3 3.5 5 5 4 5 15 15 SPI Timing Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 11/23 8.2.2 SPI Data Switching Characteristic SPI Inter face read SPI Inter face write Parameter tCS tCR tbusy tEC tDB Delay time,CS↓ to DIN read/write command valid Delay time, DIN read command invalid to DOUT/DIN card reponse valid Fixed busy delay till DOUT data valid Delay time, DOUT data invalid to CS↑ Data Block Size MIN MAX 0 1 1 7 0 1 Unit 16 Clock Cycle 16 Clock Cycle 32 Clock Cycle 16 Clock Cycle 32 Clock Cycle Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 12/23 9 Electrical Characteristics 9.1 DC/RF Characteristics for IEEE802.11b 11Mbps mode unless otherwise specified. 25deg.C, VBAT=3.6V, ENABLE=1.8V Items Contents Specification IEEE802.11b Mode DSSS / CCK Frequency 2400 - 2500MHz Data rate 1, 2, 5.5, 11Mbps - DC Characteristics min. typ. 1. DC current 1) Tx mode TBD 2) Rx mode TBD 3) Sleep mode TBD - Tx Characteristics min. typ. 2. Power Levels +19.5 3. Spectrum Mask 1) 1st side lobes 2) 2nd side lobes 4. Power-on and Power-down ramp 5. RF Carrier Suppression 15 6. Modulation Accuracy (EVM) - Rx Characteristics min. typ. 7. Minimum Input Level Sensitivity 1) 11Mbps (FER < 8%) 8. Maximum Input Level (FER < 8%) -10 0 max. unit mA mA uA unit dBm dBr dBr μsec dB % unit dBm dBm max. -30 -50 2 35 max. -76 - Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 13/23 9.2 DC/RF Characteristics for IEEE802.11g 54Mbps mode unless otherwise specified. 25deg.C, VBAT=3.6V, ENABLE =1.8V Items Contents Specification IEEE802.11g Mode OFDM Frequency 2400 - 2483.5MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps - DC Characteristics min. typ. max. 1. DC current 1) Tx mode TBD 2) Rx mode TBD 3) Sleep mode TBD - Tx Characteristics min. typ. max. 2. Power Levels +15 3. Spectrum Mask 1) at fc +/- 11MHz -20 1) at fc +/- 20MHz -28 1) at fc +/- 30MHz -40 4. Spurious Emissions 1) 30MHz to 1GHz -36 2) 1GHz to 12.75GHz -30 3) 1.8GHz to 1.9GHz -47 4) 5.15GHz to 5.3GHz -47 5. Constellation Error (EVM) -25 - Rx Characteristics min. typ. max. 6. Minimum Input Level Sensitivity 1) 54Mbps (PER < 10%) -65 7. Maximum Input Level (PER < 10%) -20 - unit mA mA uA unit dBm dBr dBr dBr dBm dBm dBm dBm dB unit dBm dBm Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 14/23 10. Land pattern 7.8 7.2 6 .8 6.2 5.8 5.2 4.8 4.2 3.8 3.2 2.8 2.2 1.8 1.2 0.8 0.2 1. 2 5 0 .2 5 4 .4 5 2 . 75 1. 7 5 5. 7 5 0 .3 1.3 1 .9 2.9 3.5 4.5 5.1 6.95 8.25 0 .2 0.8 Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 1 .2 1. 8 (unit : mm) 2.2 2 .8 3 .2 3.8 Preliminary Specification Number: SP-ZZVK P. 15/23 10. Reference Circuit Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 16/23 11. Evaluation board of LBWA1ZZVK7-TEMP LBWA1ZZVK7-TEMP Evaluation Module board (EM board) enables a pre-defined interface and form factor solution for compatibility with other TI microcontroller development boards such as MSP430 Experimenter’s board and Stellaris LM3S9B96-DK. The LBWA1ZZVK7 Module and EM board will communicate over the SPI interface through the 20pin connector. Evaluation Module board (EM board ) Part Number LBWA1ZZVK7-TEMP-D Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 17/23 12. Tape and Reel Packing (1) Dimensions of Tape (Plastic tape) T.B.D (2) Dimensions of Reel T.B.D Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 18/23 (3) Taping Diagrams [1] Feeding Hole : As specified in (1) [2] Hole for chip : As specified in (1) [3] Cover tape [4] Base tape : 62μm in thickness : As specified in (1) [3] [1] [2] [3] [4] Feeding Hole Feeding Direction Chip (4) Leader and Tail tape Feeding direction Tail tape (No components) 40 to 200mm Components No components 150mm min. Leader tape (Cover tape alone) 250mm min. Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P. 19/23 (5) The tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled toward the user. (6) The cover tape and base tape are not adhered at no components area for 250mm min. (7) Tear off strength against pulling of cover tape : 5N min. (8) Packaging unit : 500pcs./ reel (9) material : Base tape : Plastic Real : Plastic Cover tape, cavity tape and reel are made the anti-static processing. (10) Peeling of force : 0.7N max. in the direction of peeling as shown below. 0.7 N max. 165 to 180 ° Cover tape Base tape (11) Packaging (Humidity proof Packing) Label 表示ラべル Desiccant 乾燥剤 Humidity 湿度 Indicator ケ－タ インジ 表示ラベル Label 防湿梱包袋 Anti-humidity Plastic Bag Tape and reel must be sealed with the anti-humidity plastic bag. The bag contains the desiccant and the humidity indicator. Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P.20/25 NOTICE 1. Storage Conditions: Please use this product within 6 months after receipt. - The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperature over 40deg.C.) - The product left more than 6months after reception, it needs to be confirmed the solderbility before used. - The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.). - Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020) - After the packing opened, the product shall be stored at Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P.23/25 ! Note: Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. All the items and parameters in this product specification have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment agreed upon between you and us. You are requested not to use our product deviating from such agreement. We consider it not appropriate to include other terms and conditions for transaction warranty in product specifications, drawings or other technical documents. Therefore, even if your original part of this product specification includes such terms and conditions as warranty clause, product liability clause, or intellectual property infringement liability clause, we are not able to accept such terms and conditions in this product specification unless they are based on the governmental regulation or what we have agreed otherwise in a separate contact. We would like to suggest that you propose to discuss them under negotiation of contract. Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P.24/25  Disclaimer Please read this notice before using the Murata Wireless Modules. 1. Please note that the only warranty that Murata Manufacturing Co., Ltd. (“Murata”) provides regarding the products is its conformance to the specifications provided herein. Accordingly, Murata shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. MURATA HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. YOU AGREE TO INDEMNIFY AND DEFEND MURATA AND ITS AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF PRODUCTS. 2. The product is designed and manufactured for general consumer applications, and not for any particular application, so testing and use of the product shall be conducted at your own risk and responsibility. Specifically, please observe the following: i) Please conduct validation and verification of the products in actual condition of mounting and operating environment before commercial shipment of the equipment. ii) Please pay attention to minimize any mechanical vibration or shock, not to drop the product or a substrate that contains the product during transportation. iii) Since the application of static electricity or overvoltage may cause defect in the product or deterioration of its reliability, caution must be taken against exposure to any static electricity generated by electrified items such as work benches, soldering irons, tools, carrying containers, etc. iv) Caution shall be taken to avoid overstress to the product during and after the soldering process. v) Since the applied soldering method may deteriorate the reliability, thorough evaluation is recommended. vi) In case the product is to be used in equipment or electric circuit that requires high safety or reliability function or performances, sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. Please provide and appropriate fail-safe function on your product to prevent any damages that may be caused by the abnormal function or the failure of our product. Notwithstanding the foregoing, the product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. - Aircraft equipment. - Aerospace equipment - Undersea equipment. - Power plant control equipment - Medical equipment. - Transportation equipment (vehicles, trains, ships, etc.). - Traffic signal equipment. - Disaster prevention / crime prevention equipment. - Data-processing equipment - Application of similar complexity and/ or reliability requirements to the applications listed in the above. . Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number: SP-ZZVK P.25/25 3. Murata’s warranty as provided in Clause 1 above that the products comply with descriptions expressly specified in the specifications shall be effective for a period of six (6) months from the date of delivery. Murata shall not be liable for any defects that occur in dry packed products that are installed more than six (6) months after shipment. Murata’s liability under this warranty shall be limited to products that are returned during the warranty period to the address designated by Murata and that are determined by Murata not to conform to such warranty. If Murata elects to repair or replace such products, Murata shall have reasonable time to repair such products or provide replacements. Repaired products shall be warranted for the remainder of the original warranty period. Replaced products shall be warranted for a new full warranty period. For avoidance of doubt, Murata shall not be liable for any defects that are caused by neglect, misuse or mistreatment by an entity other than Murata including improper installation or testing, or for any products that have been altered or modified in any way by an entity other than Murata. Moreover, Murata shall not be liable for any defects that result from your or third party’s design, specifications or instructions for such products. 4. Testing and other quality control techniques are used to the extent Murata deems necessary. Unless mandated by government requirements, Murata does not necessarily test all parameters of each product. 5. EOL Please note that we may discontinue the manufacture of products, due to reasons such as end of supply of materials and/or components from our suppliers. Preliminary & Confidential < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.