LQH6PPN2R2N43p

Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet 1 Chip Inductor (Chip Coil) I Dimensions Power Inductor (Wire Wound Type) LQH6PP Series (2424 Size) I Packaging Code L K 6.0±0.2 4.3±0.2 (0.2) Packaging 180mm Embossed Tape 330mm Embossed Tape Minimum Quantity 250 1500 6.0±0.2 6.0±0.2 1.65±0.2 1.65±0.2 (in mm) I Rated Value (p: packaging code) Part Number LQH6PPN1R0N43p LQH6PPN1R5N43p LQH6PPN2R2N43p LQH6PPN3R3N43p LQH6PPN4R7M43p LQH6PPN6R8M43p LQH6PPN100M43p LQH6PPN150M43p LQH6PPN220M43p LQH6PPN330M43p LQH6PPN470M43p LQH6PPN680M43p LQH6PPN101M43p Inductance 1.0µH±30% 1.5µH±30% 2.2µH±30% 3.3µH±30% 4.7µH±20% 6.8µH±20% 10µH±20% 15µH±20% 22µH±20% 33µH±20% 47µH±20% 68µH±20% 100µH±20% Inductance Allowable DC Current Test Frequency (Based on Temperature Rise) 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 4.30A 4.15A 4.10A 3.80A 3.20A 2.85A 2.60A 2.20A 1.55A 1.29A 1.10A 1.00A 0.80A Allowable DC Current (Based on Inductance Change) 7.50A 6.50A 5.60A 4.50A 4.00A 3.20A 2.60A 2.20A 1.70A 1.60A 1.25A 1.10A 0.92A DC Resistance 0.009ohm±30% 0.010ohm±30% 0.014ohm±30% 0.016ohm±30% 0.020ohm±30% 0.028ohm±30% 0.044ohm±30% 0.065ohm±30% 0.108ohm±30% 0.137ohm±30% 0.230ohm±30% 0.289ohm±30% 0.436ohm±30% Self Resonance Frequency (min.) 110MHz 60MHz 30MHz 30MHz 25MHz 20MHz 15MHz 10MHz 10MHz 6MHz 6MHz 5MHz 3MHz Class of Magnetic Shield Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Operating Temperature Range: -40 to +85°C Only for reflow soldering. I Notice (Allowable DC Current) When Allowable DC Current is applied to the Products, self-generation of heat will rise to 40°C or less. When Allowable DC Current is applied to the Products, Inductance will be within +-30% of nominal Inductance value. Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.4.30 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) Data Sheet Continued from the preceding page. 2 I Inductance-Frequency Characteristics (Typ.) 1000 100µH 68µH 47µH 33µH 22µH 15µH 10µH 6.8µH 4.7µH 3.3µH 2.2µH 1.5µH 1.0µH 1 I Inductance-Current Characteristics (Typ.) 100 100µH 68µH 47µH 33µH 22µH 15µH 10µH 6.8µH 4.7µH 3.3µH 2.2µH 1.5µH 1.0µH 100 Inductance (µH) Inductance (µH) 10 10 1 0.1 0.1 1 10 Frequency (MHz) 100 1000 0.1 10 100 DC Current (mA) 1000 10000 I Temperature Rise Characteristics (Typ.) 40 100µH 68µH 47µH 30 Temperature Rise (°C) 15µH 22µH 10µH 6.8µH 4.7µH 33µH 20 10 3.3µH 2.2µH 1.5µH 1.0µH 0 0 1000 2000 3000 4000 5000 DC Current (mA) I !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.4.30 http://www.murata.com/