EVPAT2L1B000

Light Touch Switches/EVPAT 3.4 mm×1.7 mm Side-operational Edge-mount Light Touch Switches Type: EVPAT ■ Features ● External
dimensions
:
3.4
mm×1.7 mm (Excluding the push plate),
Height
1.65mm
(The height from PCB surface : 1.105 mm) ● High
operability Equipped
with
an
actuator
(push
plate) ● IP67 ■ Recommended Applications ● Operation switches for portable electronic equipment (Mobile phones, Digital still cameras, Camcorders Portable audio players, etc.) ■ Explanation of Part Numbers 1 2 3 4 Product Code 5 Type 6 7 8 9 10 (11) (12) L 1 B 0 0 0 Operating Force ■ Specifications Type Snap action/Push-on type SPST Rating 10 μA 2 V DC to 20 mA 15 V DC (Resistive load) Contact Resistance Electrical 500 mΩ max. Insulation Resistance 50 MΩ min. (at 100 V DC) Dielectric Withstanding Voltage 250 V AC for 1 minute Bouncing 10 ms max. (ON, OFF) ヒハパチワチネヒハプチワチネチビハフワチ Operating Force Mechanical パハパベチㄎㄎチドヒハパチワナチネチパハヒヒチㄎㄎチドヒハプチワチネチビハフチワナ Travel Endurance Operating Life Protective Structure 500,000 cycles IP67(＊1) Operating Temperature Dust resistance : 4 types of talc 8 h, Water resistance : Immersion depth 1 m 30 min. –40 °C to +85 °C –40 °C to +85 °C (Bulk) –20 °C to +60 °C (Taping) Storage Temperature 10,000 pcs. Embossed Taping (Reel Pack) Minimum Quantity/Packing Unit Quantity/Carton 50,000 pcs. Note: Non washable (＊1) IP67 : Switch shall not be operated during test. Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function. However, IP67 shall be guaranteed under single product state, then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage. So, please ask us in advance, if the switch is applied to important usage for water and dust resistant. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. ビパヒペハヒパ LQGXVWULDOSDQDVRQLFFRPDFH 䞊㻌㻝㻌䞊 © Panasonic Corporation 2019 モワヤヵャビブユƷビパヒペヒパ Light Touch Switches/EVPAT ■ Dimensions in mm (not to scale) EVPAT (Embossed Taping) General dimension tolerance : ±0.1 ()dimensions are reference dimensions. Molding Gate (4.55) 3.4 (Except the remainder of the molding gate ) ※Molding Gate position:"a" or "b" b 1.73 (1.9) a ① ② Circuit diagram 0.28 1.105 1.65 4 C C 2-0.15±0.05 4.4 0.4 0.69 (φ0.91) (φ0.7) ℓ 0.08±0.05 1.34 Actuator cross section (Section C-C) ① ② (2.86) 0.34±0.05 3.4±0.05 2.2±0.05 1±0.05 +0.1 1.05 0 2-1.14±0.05 1.4±0.05 2-1.54±0.05 2- R0.375 2-φ0.55 1.2 1.3 No soldering area 1 1.2 2-0.84±0.05 Soldering thickness:t=0.12±0.02 0.34±0.05 2-0.7±0.05 2-0.2±0.05 2.1 Push plate side 2.7±0.05 4.4 4.6 Edge of PCB Land pattern plan *Soldering failure may occur depending on applied solder amount,so, please consider to use our recommended stencil and land pattern desing :Recommended land pattern area :No soldering area ・Any land pattern or via holes shall not be provided at area. ・If it's necessary to design land pattern or via holes at area, please apply resist to them to protect their metal part completely. ・If their metal parts are not protected completely, short circuit failure may occur, by solder ball. ・Besides, there should be convexoconcave by designing additional pattern, it may cause swith tilt, influence on solder-ability or flux intrusion after reflow soldering. ・Therefore, please study any influence of additional land pattern or via holes at area in advance Operating Force ℓ=The length from PCB edge to tip of Push plate Height Operating Life ユヷヱモヵヒロヒャパパパ ヒハパチワ パハブピチㄎㄎ ヒハヒパブチㄎㄎ ブパパネパパパチ㄄ㄚ㄄ㄍㄆㄔ ユヷヱモヵビロヒャパパパ ヒハプチワ パハブプチㄎㄎ ヒハヒパブチㄎㄎ ブパパネパパパチ㄄ㄚ㄄ㄍㄆㄔ ユヷヱモヵモロヒャパパパ ビハフチワ パハブベブチㄎㄎ ヒハヒパブチㄎㄎ ブパパネパパパチ㄄ㄚ㄄ㄍㄆㄔ Part Numbers Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ac/e/ 䞊㻌㻞㻌䞊 © Panasonic Corporation 2019 モワヤヵャビブユƷビパヒペヒパ Light Touch Switches/EVPAT ■ Recommended Reflow Soldering Conditions Operation Top (°C) MAX. 260 Fan or Normal Temp. 230 180 150 (Normal Temp.) 90±30 40±10 Soldering Time (s) Reflow temperature may vary by location even in the same reflow condition. Please check the reflow temperature at terminals and at the top of a switch to make sure the both temperatures are withiin the specification. If even one of them is out of the specifi cations, please adjust. ● Embossed Carrier Taping Tape width=12.0 mm (A=12.0 mm) F K L H I A M C B E G D t J Take out direction Part No. Height EVPAT 1.105 A B Unit:mm C D E Taping condition : Lack of products in the middle of taping should be one MAX, but total quantity specified in the specifications should be secured. Peeling off strength of top tape : It should be within 0.2N to 1.0N at 165 degree in peeling off angle. Joint of carrier tape : One joint per one reel may exist. F G 12.0±0.2 1.75±0.10 5.50±0.05 4.0±0.1 4.0±0.1 2.00±0.05 1.5 +0.1 -0 H I 2.28±0.20 4.8±0.2 J K L M Unit: mm t (1.065) 1.23±0.10 0.77±0.10 (10.25) 0.30±0.05 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Panasonic Corporation Electromechanical Control Business Division industrial.panasonic.com/ac/e/ 䞊㻌㻟㻌䞊 © Panasonic Corporation 2019 モワヤヵャビブユƷビパヒペヒパ Requests to customers Please refer to "the latest product specifications" when designing your product. Requests to customers : https://industrial.panasonic.com/ac/e/salespolicies/ Safety Precautions When using our products, no matter what sort of equipment they might be used for, be sure to confirm the applications and environmental conditions with our specifications in advance. Please contact .......... Electromechanical Control Business Division 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan industrial.panasonic.com/ac/e/ ©Panasonic Corporation 2019 モワヤヵャビブユチチチビパヒペヒパ Specifications are subject to change without notice.