SC-GU3-03

Communication Unit for EtherCAT SC-GU3-03 EtherCATEnables remote operation and monitoring sensors via a PC network! compatible MONITORING Enables preventative maintenance and traceability by monitoring Logging of a various sensor information operating conditions. The setting of sensors can be changed via a PC. OPERATION Reduces on-site setup time and improves work efficiency. EtherCAT ORDER GUIDE Communication unit for EtherCAT End plate SC-GU3-03 MS-DIN-E Main communication unit which converts the data received from any attached sensors to communication data for EtherCAT networks. Used to fix the entire SC-GU3 stack to a DIN rail for reliable performance. Highly recommended. End unit Compatible installation tool for SC SC-GU3-EU SC-BUX10 This end unit can change and check the settings of sensor amplifiers that allow optical communication and monitor operation status. Used to install SC-T8J/SC-MIL-S to the SC-GU3-0□. OPTION 10 pcs. per set Cascading connector unit Connection cable SC-71 CN-M20-C2 This one-touch connector is used to connect the following devices to SC-GU3-0□:The FX-500/400/300 fiber sensor, the LS-400 laser sensor, the DPS-400 digital pressure sensor, SC-T1J and SC-T1JA, etc. Standard connector cable for linking to the parallel output signal. EtherCAT is a registered trademark of Beckhoff Automation GmbH. Please refer to our website or SC-GU3 series catalog for other products. 2012.07 2 pcs. per set panasonic.net/id/pidsx/global OPTION SPECIFICATIONS Designation Item SYSTEM COMPOSITION Communication unit for EtherCAT SC-GU3-03 Model No. Number of connectable units Max. 16 units per SC-GU3-03 (Max. 12 units for FX-500 Series) Supply voltage End unit SC-GU3-EU (Optional) 24 V DC ±10 % Ripple P-P 10 % or less Current consumption 100 mA or less (excluding connected sensor amplifiers) Allowable passing current Wire-saving connector 2 A (Note 1) Compliance standard IEEE802.3u Baud rate Cascading connector unit SC-71 (Optional) End plate MS-DIN-E (Optional) Communication cable Category 5e Internodal distance 100 m 328.1ft Communication ports RJ45×2 EtherCAT communication standards Process data communication, Mailbox communication Digital communication supporting sensors (optical communication compatible) FX-501, FX-502, FX-301 (those produced after June 2004), FX-305 Laser sensor Pressure sensors LS-403 DPS-401, DPS-402 Sensor input unit SC-T1JA (in combination with SC-71) Sensors that only output information (not optical communication compatible) FX-301 (those produced up to May 2004) Fiber sensors Manually set fiber sensors Fiber sensors for leaks/liquid fibers Material Enclosure: Polycarbonate Weight Net weight: 75 g approx., Gross weight: 120 g approx. Laser sensor Compact inductive proximity sensor 1-channel connector input extension unit 8-channel connector input extension unit 8-channel connector I/O extension unit EtherCAT is a registered trademark of Beckhoff Automation GmbH. Notes: 1) Be sure to check that total current consumption of sensor amplifiers connected in cascade does not exceed allowable passing current. 2) XML file can be downloaded from our website. Plug-in type sensor main unit Plug-in type sensor separate unit DIMENSIONS (Unit: mm in) FX-411, FX-412, FX-311 (B/G) FX-301-F, FX-301-F7 LS-401 GA-311 SC-T1J (in combination with SC-71) SC-T8J (those produced from June 2011, in combination with SC-BU) SC-TP8J (those produced from June 2011, in combination with SC-BU) This unit does not contain input / output signal indicators. SC-MIL (those produced from June 2011, in combination with SC-BU) SC-MIL-S (those produced from June 2011, in combination with SC-BU) The CAD data in the dimensions can be downloaded from our website. Operation mode setting switch cover 74.2 2.921 62.2 2.449 50.2 1.976 EtherCAT setting switch 5.5 0.217 Fiber sensors FX-301 (B/G/H) , FX-301-HS 35 to 85 % RH, Storage: 35 to 85 % RH 13.4 0.528 Communication unit for EtherCAT SC-GU3-03 SC-GU3-Compatible Sensors –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), (If 4 to 7 units are connected in cascade: –10 to +50 °C +14 to +122 °F, if 8 to 16 units are connected in cascade : –10 to +45 °C +14 to +113 °F) Storage: –20 to +70 °C – 4 to +158 °F Ambient humidity End plate MS-DIN-E (Optional) Sensor amplifier (Optional) 100 Mbps Ambient temperature If optical communication is to be used in a system that includes models not compatible with optical communication, connect the incompatible models after the SC-GU3-EU. A maximum of 12 units can be connected to the FX-500 Series, and a maximum of 16 units can be connected to the other sensor amplifiers. Without an operation mode setting switch cover and a connector for output signal Operation mode setting switch Memory/ Reset key Connector cover for output signal (38.6) (1.520) 1.5 0.059 (12.16) (0.479) 2.5 0.098 (7.55) (0.297) L/A OUT(communication state) indicator (Green) Memory function indicator (Yellow) 63.1 2.484 71.1 2.799 79.1 3.114 87.1 3.429 Power indicator (Green) ERR. indicator (Red) Connection window 52 2.047 ECAT ERR (communication error) indicator (Red) L/A IN (communication state) indicator (Green) RUN (operation) indicator (Green) EtherCAT connector 22.8 0.898 40 1.575 33 1.299 32.9 1.295 39.6 (27.8) 1.559 (1.094) 36.9 1.452 38.6 1.520 (12.5) 5.6 (0.492) 0.220 Compliant with 35 mm 1.38 in width DIN rail 36.5 1.437 96.7 3.807 4.5 0.177 (34.2) (1.346) 9 0.354 24.3 0.957 4.4 0.173 Power connector 6.1 0.240 Connection window 7.8 0.307 Connector for output signal