TN2-L2-H-9V

SLIM POLARIZED RELAY TN-RELAYS • Surge voltage withstand: 1500 V FCC Part 68 • Sealed construction allows automatic cleaning • Self-clinching terminal also available 14 .551 5.6 .220 9.8 .386 FEATURES • Small size for minimal PC board mounting requirements • Small header area makes higher density mounting possible • High sensitivity: 140 mW nominal operating power (single side stable 3-12 V type) mm inch SPECIFICATIONS Contact Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1A) Contact material Nominal switching capacity (resistive load) Max. switching power (resistive load) Rating Max. switching voltage Max. switching current Min. switching capacity f1 Single side stable Nominal operating power 1 coil latching 2 coil latching Mechanical (at 180 cpm) 1 A 30 V DC resistive load Electrical (at 20 cpm) 0.5 A 125 V AC resistive load 2 Form C 60 mΩ Gold-clad silver 1 A 30 V DC, 0.5 A 125 V AC 30 W, 62.5 VA 110 V DC,125 V AC 1A 10 µA 10 mV DC 140 mW (3 to 12 V DC) 200 mW (24 V DC) 300 mW (48 V DC) 100 mW (3 to 12 V DC) 150 mW (24 V DC) 200 mW (3 to 12 V DC) 300 mW (24 V DC) 108 2 × 105 105 Characteristics Initial insulation resistance*1 Between open contacts Initial Between contact and breakdown coil voltage Between contact sets FCC surge voltage between open contacts Temperature rise*2 (at 20°C) Operate time [Set time]*3 (at 20°C) Release time [Reset time]*4 (at 20°C) Functional*5 Shock resistance Destructive*6 Functional*7 Vibration resistance Destructive Conditions for operation, transport and storage*8 (Not freezing and condensing at low temperature) Unit weight Ambient temperature Humidity Max. 3 [Max. 3 Max. 3 [Max. 3 Min. 1,000 MΩ (at 500 V DC) 750 Vrms for 1 min. (Detection current: 10 mA) 1,000 Vrms for 1 min. (Detection current: 10 mA) 1,000 Vrms for 1 min. (Detection current: 10 mA) 1,500 V Max. 50°C ms (Approx. 2 ms (Approx. 2 ms (Approx. 1 ms (Approx. 2 ms) ms)] ms) ms)] Expected life (min. operations) Note: Min. 490 m/s2 {50G} Min. 980 m/s2 {100G} 176.4 m/s2 {18G}, 10 to 55 Hz at double amplitude of 3 mm 294 m/s2 {30G}, 10 to 55 Hz at double amplitude of 5 mm –40°C to +70°C –40°F to +158°F 5 to 85% R.H. Approx. 1.5 g .053 oz f1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section. *2 By resistive method, nominal voltage applied to the coil; contact carrying current: 1 A. *3 Nominal voltage applied to the coil, excluding contact bounce time. 4 Nominal voltage applied to the coil, excluding contact bounce time without diode. * *5 Half-wave pulse of sine wave: 11 ms; detection time: 10 µs. *6 Half-wave pulse of sine wave: 6 ms. *7 Detection time: 10 µs. *8 Refer to 4. Conditions for operation, transport and storage mentioned in Cautions for use (Page 178). ORDERING INFORMATION Ex. TN 2 L2 H 12V Contact arrangement 2: 2 Form C Operating function Nil: Single side stable L: 1 coil latching L2: 2 coil latching Terminal shape Nil: Standard PC board terminal H: Self-clinching terminal Coil voltage(DC) 3,4.5,5,6,9,12, 24,48*V *48 V coil type: Single side stable only Note: AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix “–3” like TN2–12V–3. 150 TN TYPES AND COIL DATA (at 20°C 68°F) 1. Single side stable Part No. Standard PC board terminal TN2-3 V TN2-4.5 V TN2-5 V TN2-6 V TN2-9 V TN2-12 V TN2-24 V TN2-48 V Self-clinching terminal TN2-H-3 V TN2-H-4.5 V TN2-H-5 V TN2-H-6 V TN2-H-9 V TN2-H-12 V TN2-H-24 V TN2-H-48 V Nominal voltage, V DC 3 4.5 5 6 9 12 24 48 Pick-up voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 36 Drop-out voltage, V DC (min.) 0.3 0.45 0.5 0.6 0.9 1.2 2.4 4.8 Nominal operating current, mA (±10%) 46.7 31.1 28.1 23.3 15.5 11.7 8.3 6.25 Coil resistance, Ω (±10%) 64.3 145 178 257 579 1,028 2,880 7,680 Nominal operating power, mW 140 140 140 140 140 140 200 300 Max. allowable voltage, V DC 4.5 6.7 7.5 9 13.5 18 36 57.6 2. 1 Coil latching Part No. Standard PC board terminal TN2-L-3 V TN2-L-4.5 V TN2-L-5 V TN2-L-6 V TN2-L-9 V TN2-L-12 V TN2-L-24 V Self-clinching terminal TN2-L-H-3 V TN2-L-H-4.5 V TN2-L-H-5 V TN2-L-H-6 V TN2-L-H-9 V TN2-L-H-12 V TN2-L-H-24 V Nominal voltage, V DC 3 4.5 5 6 9 12 24 Set voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Reset voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Nominal operating current, mA (±10%) 33.3 22.2 20 16.7 11.1 8.3 6.3 Coil resistance, Ω (±10%) 90 202.5 250 360 810 1,440 3,840 Nominal operating power, mW 100 100 100 100 100 100 150 Max. allowable voltage, V DC 4.5 6.7 7.5 9 13.5 18 36 3. 2 Coil latching Part No. Standard PC board terminal TN2-L2-3 V TN2-L2-4.5 V TN2-L2-5 V TN2-L2-6 V TN2-L2-9 V TN2-L2-12 V TN2-L2-24 V Notes: 1. Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 2. Standard packing: Tube: 50 pcs.; Case: 1,000 pcs. 3. In case of 5 V drive circuit, it is recommended to use 4.5 V type relay. 4. AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TN2-12V-3. Self-clinching terminal TN2-L2-H-3 V TN2-L2-H-4.5 V TN2-L2-H-5 V TN2-L2-H-6 V TN2-L2-H-9 V TN2-L2-H-12 V TN2-L2-H-24 V Nominal voltage, V DC 3 4.5 5 6 9 12 24 Set voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Reset voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Nominal operating current, mA (±10%) 66.7 44.4 40 33.3 22.2 16.7 12.5 Coil resistance, Ω (±10%) 45 101.2 125 180 405 720 1,920 Nominal operating power, mW 200 200 200 200 200 200 300 Max. allowable voltage, V DC 4.5 6.7 7.5 9 13.5 18 28.8 DIMENSIONS Standard PC board terminal 14 551 9.5 9.8.374 .386 3.5 .138 2.54 .100 0.5 .020 1.385 .055 0.25 .010 2.54 .100 5.6 .220 mm inch PC board pattern (Copper-side view) 10.16 .400 2.54 .100 2.54 .100 10-1.0 dia. hole 10-.039 dia. hole Tolerance: ±0.1 ±.004 Self-clinching terminal 14 551 9.5 9.8.374 .386 3.5 .138 2.54 .100 0.5 .020 1.385 .055 0.25 .010 2.54 .100 5.6 .220 Schematic (Bottom view) • Single side stable • 1-coil latching (Deenergized condition) (Reset condition) 12345 12345 • 2-coil latching (Reset condition) 12345 10 9 8 7 6 Direction indication* 10 9 8 7 6 Direction indication* 10 9 8 7 6 Direction indication* General tolerance: ±0.3 ±.012 *Orientation stripe located on top of relay 151 TN REFERENCE DATA 1. Maximum switching capacity 2. Life curve 3. Mechanical life Tested sample: TN2-12V, 10 pcs. DC load (cosϕ=1) AC load (cosϕ=1) 1.0 Ratio against the rated voltage, %V 100 90 80 70 60 50 40 30 20 10 30 100 Switching voltage,V 200 0 1.0 0.5 Switching current, A 0 10 100 1,000 No. of operations, ×104 Drop-out voltage Max. Min. Pick-up voltage Max. Min. 0.5 0.4 0.3 0.2 No. of operations, ×104 30 V DC resistive load Switching current, A 100 125 V AC resistive load 10 10,000 4. Electrical life (DC load) Tested sample: TN2-12V, 10 pcs. Condition: 1 A 30 V DC resistive load, 20 cpm 5. Coil temperature rise Tested sample: TN2-12V Point measured: Inside the coil Ambient temperature: Room temperature (25° to 26°C), 70°C (77° to 79°F), 158°F 70 60 Temperature rise, °C 50 40 30 20 10 0 Carrying current 0 A (Room temp.) 1 A (Room temp.) 0 A (70°C) 1 A (70°C) Change of pick-up and drop-out voltage Ratio against the rated voltage %V 100 90 80 70 60 50 40 30 20 10 0 5 10 15 No. of operations, ×104 20 Min. Drop-out voltage Max. Change of contact resistance 100 90 Contact resistance,mΩ Pick-up voltage 80 70 60 50 40 30 20 10 0 5 10 15 No.of operations, ×104 20 Terminal No.2–3–4 Terminal No.7–8–9 Max. Min. 80 90 100 110 120 130 140 150 Coil applied voltage, %V 6. Operate/release time characteristics Tested sample: TN2-12V, 5 pcs. 6 Operate and release time, ms 7. Set/reset time characteristics Tested sample: TN2-L2-12V, 5 pcs. 6 Set time Set and reset time, ms Reset time 8. Distribution of pick-up and drop-out voltages Tested sample: TN2-12V, 40 pcs. 30 5 5 Pick-up voltage Quantity 20 4 4 Drop-out voltage 3 Operate time Max. Min. Max. Min. 3 2 2 Max. Min. 10 1 Release time 0 80 1 0 90 100 110 120 Coil applied voltage, %V 80 90 100 110 120 Coil applied voltage, %V 0 10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V 9. Distribution of set and reset voltage Tested sample: TN2-L2-12V, 32 pcs. 30 10. Ambient temperature characteristics Tested sample: TN2-12V, 5 pcs. x Variation ratio, % 40 30 Drop-out voltage 11. Distribution of contact resistance Tested sample: TN2-12V, 38 pcs. (38×4 contacts) 40 12345 ,,,, ,, ,, ,,, , ,, ,, , , Set voltage Reset voltage 30 20 Quantity x Quantity 20 Terminal No. 7,8,9 Side 6 7 8 9 10 Terminal No. 2,3,4 side 10 Pick-up voltage –40 –20 –10 0 Ambient 20 40 60 80 temperature, °C –10 –20 –30 –40 20 10 10 0 10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V 0 30 40 50 Contact resistance,mΩ 152 TN 12-(1). Malfunctional shock (single side stable) Tested sample: TN2-12V, 6 pcs. , Z Z 12-(2). Malfunctional shock (latching) Tested sample: TN2-L2-12V, 6 pcs. , Z Z Y Y, Y X X , Y 980m/s2 Deenergized condition Energized condition Y, X X , 980m/s2 Y Deenergized condition Energized condition X 980m/s2 Z 980m/s2 X 980m/s2 Z 980m/s2 , Z 980m/s2 980m/s2 , Y , X 980m/s2 , Z 980m/s2 980m/s2 , Y , X 980m/s2 13-(1). Influence of adjacent mounting Rate of change, % 10 Pick-up voltage 0 –10 ON 13-(2). Influence of adjacent mounting Rate of change, % 10 Pick-up voltage 0 –10 ON ON ON ON ON Rate of change, % OFF OFF Rate of change, % OFF OFF 10 Drop-out voltage 0 –10 0 5 .197 Inter-relay distance OFF 20 Drop-out voltage 10 0 0 5 .197 Inter-relay distance OFF , mm inch , mm inch 14. Actual load test (35 mA 48 V DC wire spring relay load) Change of pick-up and drop-out voltage 100 Ratio against the rated voltage, %V 90 Contact resistance, mΩ 80 70 60 50 40 30 20 10 0 10 20 30 40 No. of operations,×104 50 Drop-out voltage Max. Min. Pick-up voltage Max. Min. Change of contact resistance 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 No. of operations, ×104 50 Terminal No. 2–3 Max. Min. Circuit 500Ω 48 V DC 0.1 µF 0.1 µF 500Ω 3 2 Wire spring relay Circuit diagram 15-(1). High-frequency characteristics Tested sample: TN2-xxV Isolation characteristics 15-(2). High-frequency characteristics Tested sample: TN2-xxV Insertion loss characteristics 1.6 15-(3). High-frequency characteristics Tested sample: TN2-xxV V.S.W.R. 2.2 2.1 2.0 V.S.W.R. 1.9 1.8 1.7 1.6 1.5 1.4 1.3 Insertion loss, dB 1.4 1.2 1.0 Terminal No. 2–3–4 0.8 0.6 Isolation, dB 100 Terminal No. 7–8–9 50 Terminal No. 2–3–4 Terminal No. 2-3-4 Terminal No. 7-8-9 0.4 Terminal No. 7–8–9 0.2 1.2 1.1 1.0 10 100 Frequency, MHz 1000 10 100 Frequency, MHz 1000 10 100 Frequency, MHz 1000 For Cautions for Use, see Page 178 and 179. 9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, 153 Ltd. Go To Online Catalog