ZU-1870MU1

SPECIFICATIONS Manual Insertion Type Magnetic Card Reader ZU–1870MU1 NOTE: APPROVAL Panasonic Communications Co.,Ltd. Devices and Components Company 2111 Ueda, Usa City, Oita 879-0493, JAPAN REF No. MIS-DG60B144 REV A DATE PREPARED LAWS APPROVED Q A SALES KOK-B3-601-T2 Issue1 Specification for ZU-1870MU1 Copyright © 2007 Panasonic / Panasonic Communications Co., Ltd. All rights reserved. Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd. Other company, product, and service names may be trademarks or service marks of others. Revision History Document No. Note: Date Description Page No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Panasonic Communications Co., Ltd. In case there is any contradiction appeared based on technical standard change/update etc., our specifications shall take precedence over such change/update. © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No.: MIS-DG60B144A Page.1 Specification for ZU-1870MU1 Table of Contents 1. Introduction ....................................................................................................................... 3 2. Product Name and Model #.......................................................................................... 3 3. Equipment Specification................................................................................................ 3 3.1. 3.2. 3.3. 4. Basic features..................................................................................................................................... 3 Electrical specification....................................................................................................................... 3 Physical dimension............................................................................................................................ 3 Environments.................................................................................................................... 3 5. Card Specification ........................................................................................................... 5 5.1. 5.2. 5.3. 6. Magnetic reading ............................................................................................................................... 5 Physical characteristics .................................................................................................................... 6 Magnetic characteristics ................................................................................................................... 6 Terminal No. of connector ............................................................................................. 6 7. Interface specification .................................................................................................... 7 7.1. 7.2. Configuration Properties................................................................................................................... 7 Message Format................................................................................................................................ 7 8. Unit life and reliability..................................................................................................... 8 9. Period of guarantee......................................................................................................... 8 10. Maintenance ...................................................................................................................... 8 11. Precautions ....................................................................................................................... 8 11.1. 11.2. 12. Handling .......................................................................................................................................... 8 Cautions .......................................................................................................................................... 8 Appearance ..................................................................................................................... 10 © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No.: MIS-DG60B144A Page.2 Specification for ZU-1870MU1 1. Introduction This specification describes Panasonic’s Manual Insertion Type Magnetic Card Reader Model # ZU-1870MU1. Features of the reader are as follows: • • • • • This card reader has the USB (Keyboard Emulation) interface. Communications with a Host Computer through USB connection. Reads Track 1 and Track 2 of standard Magnetic Stripe Cards per ISO standards. Can use standard Windows drivers for communications. No third part device driver is required. Raindrop proof design (IPX4) 2. Product Name and Model # Product Name: Model #: Support Operating System: Manual insertion type magnetic card reader with USB ZU-1870MU1 Microsoft© Windows© XP Home/Professional Edition 3. Equipment Specification 3.1. Basic features Card operating speed: Card operation: 10 cm/s ～ 120 cm/s Insertion / Ejection (Data is transmitted as keyboard data after inserting a card and ejecting a card from a card reader. Refer to 7 ) Read/Write: Magnetic Head: Read only Double sided heads 3.2. Electrical specification Power supply: Current consumption: DC 5 V ± 0.25 V 40 mA max. 3.3. Physical dimension Width: Depth: Height: Weight: 93.5 mm 121.0 mm 50.0 mm Approx. 130 g 4. Environments Operating temperature range: Storage temperature range: Operating humidity range: Storage humidity range: 0 °C ~ 60 °C -30 °C ~ 70 ℃ 10 % ~ 90 % RH (No condensation allowed) 10 %～95 % RH (No condensation allowed) © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 3 Specification for ZU-1870MU1 Environment requirements Outdoor acceptable under following condition Note)This card reader is designed to have water protection level IPX4. To achieve the level for this card reader, card readerrequires sealing the bezel to the main unit (Customer box) by utilizing a sealant or gasket on the bezel. Such sealing must prevent main body of this card reader from being exposed to moisture. Main unit (Customer box) that card reader is installed must be sealed with the internal temperature, humidity and etc. meeting this specification. © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 4 Specification for ZU-1870MU1 5. Card Specification 5.1. Magnetic reading Card standard: Card standard Track used Recording method Recording density Recording capacity ISO1 Track 1st F2F 210 BPI 79 characters (7 bit code) ISO2 Track 2nd F2F 75 BPI 40 characters (5 bit code) Dimensions in millimeters Top reference edge 53.92 to 54.18 Front of the card 85.47 to 85.90 Top reference edge 5.66 max. 8.46 min. / 8.97 max. 8.97 max. / 8.46 min. 11.76 min. / 12.27 max. 12.52 max. / 12.01 min. 15.32 min. / 15.82 max. Track 1 Track 2 Track 3 Magnetic stripe 6.93 min. Center line of last data bit Track 1, 2: 7.44 ± 0.51 Track 3: Center line of first data bit Back of the card © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 5 Specification for ZU-1870MU1 5.2. Physical characteristics Thickness: Warpage: 0.76 mm ( tolerance ± 0.08 mm ) 2.5 mm max. (Include relief height of embossed characters) 5.3. Magnetic characteristics Coercive force (Hc): Residual flux (¢r): Squareness ratio (¢r/¢m): 2.4 x 104 A/m to 2.4 x 105 A/m 1.25 Maxwell/cm ± 0.15 Maxwell/cm More than 0.70 6. Terminal No. of connector Pin No. & Signal Name: Card reader side: Cable side: Housing: Contact: 53261-0571 (Molex) Connector Signal Pin No. Name 1 +5V 2 D3 D+ 4 SG 5 FG 51021-05** (Molex) 50079-81** (Molex) © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 6 Specification for ZU-1870MU1 7. Interface specification This card reader compatible with USB specification revision 1.1 and Human Interface Device (HID) class specification version 1.1. The reader communicates to the host as Human Interface Device (HID) keyboard. Microsoft Windows XP Home/Professional Edition operating system has a standard USB HID keyboard device driver. This card reader is a low speed USB device. Data is transmitted as keyboard data after inserting a card and ejecting a card from a card reader. In case of reading error occurs during a card insertion, reading is tried again during a card ejection. The reader can not transmit card data to keyboard code correctly in case of following: • Operating system other than U.S. version • On states Caps lock key or Num lock key • Card is read during keyboard input 7.1. Configuration Properties Configuration properties of USB descriptors as follows: Vendor ID: 0x04da Product ID: 0x117c Transfer Type: Interrupt Max Packet Size: 8 bytes Polling Interval: 10 msec 7.2. Message Format Track 1 Track 2 T1SS T1Data ES T2SS T2Data ES “%” Any “?” “;” Any “?” where: T1SS T2SS TnData ES LRC LRC (2 byte) CR (carriage return) “%” (Track 1 start sentinel) “;” (Track 2 start sentinel) Track Data “?” (end sentinel) Is the result of an EXCLUSIVE OR (XOR) between the start sentinel and the end sentinel. (ASCII Code) CR SS example: carriage return T1 and T2 card: % Track 1 ? T2 read error or T1 only card: % Track 1 ? LRC T1 read error or T2 only card: ; Track 2 ? LRC T1 and T2 read error or data nothing: Track 2 ; ? LRC (no data) © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 7 Specification for ZU-1870MU1 8. Unit life and reliability Magnetic head Life: Note: 500,000 times pass The life is reliability number based on the result tested in a “clean office” environment. Above life cycles are the numbers which are tested in a “clean office environment“. These numbers may be shortened dependent on the actual environment. Especially in a dusty environment*, even in the indoor application, dust or sand may shorten the life against the mechanical parts and most of the card transport mechanisms. In these case, warranty of the card reader may be void unless the proper protection and countermeasures are performed by the terminal side. (e.g. If used in dusty conditions, the life of the magnetic head will decrease from 1/3 to 1/5 of the above values.) *Dusty environment: Refer to ex.) IEC 68, EN30721-3-3 class 3S2 or worse. 9. Period of guarantee If defects should occur within one year after acceptance inspection of the machine due to improper material or workmanship, the defective parts shall be replaced or repaired, free of charge. 10. Maintenance Because of difficulty in changing components on the P.C Board, replacement of whole unit is recommended for service and maintenance. 11. Precautions Please be noted that we do not guarantee proper performance of the card reader if it is used other than the indicated specification range. 11.1. Handling • • Do not drop or give excessive shocks to this unit. Do not disassemble this unit. 11.2. Cautions Card • • Be sure to use a card, which conforms for the card specification. (please refer to “5. Card specification” on page 2) Store the card carefully so as not to soil, injure or deform it. In particular, deposit of solid matter on the magnetic stripe surface may result in a trouble. Cleaning • Clean the magnetic head by periodically passing a cleaning card. For example, in a clean office room, pass the cleaning card about once a week. If the magnetic head is heavily stained, clean the head by soaking the cleaning card in alcohol properly and pass the card. For example, in the case that the card readers are used in the environment full of dust, please make a cleaning of the card reader with a cleaning card with alcohol everyday. © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 8 Specification for ZU-1870MU1 Installing • • • • • • • • Be sure to install on a flat surface so as to prevent any force to be applied to the card reader at the installation. In the case that it is to incorporate into a machine, be sure not to touch any part of machine structures to the flexible P.C.B. Especially, electric noise on this area should be avoided not cause reading error. Do not touch the printed circuit board with bare hand. Note: particularly static electricity. When installing the card reader, avoid dusty, hot or damp place, or near magnetic field or object generating inductive noise (printer, LED display unit, CRT, etc.). Avoid using the unit in a dusty place or otherwise the reading accuracy may be deteriorated. Keep the unit away from objects that generate magnetism. It may cause read errors and may cause damage to the magnetic card data. Do not supply power from other outlet than connector terminal. Pay special attention to the polarity of power source and wrong connection of connector. Do not use the unit in a place where it is exposed to direct sunlight or splashed by water. FG pin should be connected to FG at customer side in low impedance. In case that FG pin is not connected to FG, electrostatic resisting capability will decrease. Others • • • • • Check the noise, static electricity, etc., with the card reader being incorporated in the equipment. It is possible for the noise from the power supply to cause the reading errors. The equipment which the card reader is built in should be taken measures to reduce the noise from power supply. The operation guarantee temperature range is 0 °C to +60°C and humidity range is 10 % to 90 % RH. Do not use the unit if condensation gathers on it. We recommend you to use the card reader under the environmental condition of temperature +10 °C to +40 °C which is the best for transferring cards and reading data. Especially, in the condition of low temperature, provide heating system separately to warm up card reader. Do not give any vibration more than following conditions, when a card is in the card reader. Conditions: 5 Hz to 50 Hz , 10 m/s2 , sweep , 0.5 oct/min (X,Y,Z direction) Do not give any shock more than 100 m/s2 and more than 1 time, when a card is in the card reader. Card operation speed should be within the specification range. Forced stop or change of speed during the card operation may cause a read error. Appropriate speed to maintain stable operation is 30 cm/s ～ 60 cm/s. © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 9 Specification for ZU-1870MU1 12. Appearance The product label with which the manufacturing number was printed is stuck on the reader module. ZU-1870MU1 65 U Manufactured month: January, February ... September = 1, 2 ... 9, October = O, November = N, December = D Manufactured year: The last digit of the Christian era © 2007 Panasonic Communications Co., Ltd. Devices and Components Company Information Equipment Category Specification No. MIS-DG60B144A Page. 10