UPB1510GV

DATA SHEET BIPOLAR DIGITAL INTEGRATED CIRCUIT µPB1510GV 3 GHz INPUT DIVIDE BY 4 PRESCALER IC FOR DBS TUNERS The µPB1510GV is a 3.0 GHz input divide by 4 prescaler IC for DBS tuner applications. The µPB1510GV is suitable for use of frequency divider for PLL synthesizer block. The µPB1510GV is a shrink package version of the µPB585G so that this small package contributes to reduce the mounting space. The µPB1510GV is manufactured using NEC’s high fT NESAT™ IV silicon bipolar process. This process uses silicon nitride passivation film and gold electrodes. These materials can protect chip surface from external pollution and prevent corrosion/migration. Thus, this IC has excellent performance, uniformity and reliability. FEATURES • • • • High toggle frequency Low current consumption Fixed division : fin = 0.5 GHz to 3.0 GHz : 5 V, 14 mA TYP. : ÷4 High-density surface mounting : 8-pin plastic SSOP (175 mil) APPLICATION • • Prescaler between local oscillator and PLL frequency synthesizer included modulus prescaler DBS tuners with kit use of VHF/UHF band PLL frequency synthesizer ORDERING INFORMATION Part Number Package 8-pin plastic SSOP (175 mil) Marking 1510 Supplying Form Embossed tape 8 mm wide. Pin 1 is in tape pull-out direction. 1000 p/reel µPB1510GV-E1 Remark To order evaluation samples, please contact your local NEC sales office. (Part number for sample order: µPB1510GV) Caution Electro-static sensitive devices T he information in this document is subject to change without notice. Document No. P12752EJ2V0DS00 (2nd edition) Date Published October 1998 N CP(K) Printed in Japan The mark shows major revised points. © 1997 µ PB1510GV PIN CONNECTION (Top View) Pin No. 1 8 Pin name VCC IN IN GND GND NC OUT NC 1 2 2 7 3 3 6 4 5 4 5 6 7 8 PRODUCT LINE-UP Features (Division, Frequency) ÷4, 2.5 GHz input ÷4, 3.0 GHz input Part number ICC (mA) 18 14 fin (GHz) 0.5 to 2.5 0.5 to 3.0 VCC (V) 4.5 to 5.5 4.5 to 5.5 Package 8-pin SOP (225 mil) 8-pin SSOP (175 mil) Pin Connection NEC Original µPB585G µPB1510GV Remark This table shows the TYP values of main parameters. Please refer to ELECTRICAL CHARACTERISTICS. µPB585G is discontinued. INTERNAL BLOCK DIAGRAM D CLK Q IN CLK Q CLK D Q Q AMP OUT IN SYSTEM APPLICATION EXAMPLE RF unit block of DBS tuners 1st IF input from DBS converter BPF MIX SAW AGC amp. FM demo. Baseband output µ PB1510GV OSC ÷4 Prescaler PLL synth. for VHF/UHF band LPF 2 µ PB1510GV PIN EXPLANATION Applied Voltage (Unit: V) 4.5 to 5.5 Pin Voltage (Unit: V)  Pin No. 1 Symbol VCC Functions and Explanation Supply voltage pin. This pin must be equipped with bypass capacitor (e.g. 1 000 pF) to minimize ground impedance. Signal input pin. This pin should be coupled to signal source with capacitor (e.g. 1 000 pF) for DC cut. Signal input bypass pin. This pin must be equipped with bypass capacitor (e.g. 1 000 pF) to minimize ground impedance. Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance. Non connection pins. These pins should be opened. Divided frequency output pin. This pin is designed as emitter follower output. This pin can be connected to input of prescaler within PLL synthesizer through DC cut capacitor. 2 IN   1.7 to 4.95 3 IN 1.7 to 4.95 4, 5 GND 0  6, 8 7 NC OUT    1.0 to 4.7 3 µ PB1510GV ABSOLUTE MAXIMUM RATINGS Parameter Supply voltage Total power dissipation Symbol VCC PD TA = +25 °C Mounted on double sided copper clad 50 × 50 × 1.6 mm epoxy glass PWB (TA = +85 °C) Conditions Ratings 6.0 250 −40 to +85 −55 to +150 Unit V mW °C °C Operating ambient temperature Storage temperature TA Tstg RECOMMENDED OPERATING CONDITIONS Parameter Supply voltage Operating ambient temperature Symbol VCC TA MIN. 4.5 −40 TYP. 5.0 +25 MAX. 5.5 +85 Unit V °C Notice ELECTRICAL CHARACTERISTICS (TA = −40 to +85 °C, VCC = 4.5 to 5.5 V, ZS = ZL = 50 Ω) Parameter Circuit current Upper limit operating frequency 1 Upper limit operating frequency 2 Lower limit operating frequency Input power 1 Input power 2 Output power Symbol ICC fin(U)1 fin(U)2 fin(L) Pin1 Pin2 Pout Test Conditions No signals Pin = −10 to +6 dBm Pin = −15 to +6 dBm Pin = −15 to +6 dBm fin = 2.7 to 3.0 GHz fin = 0.5 to 2.7 GHz Pin = 0 dBm, fin = 2.0 GHz MIN. 10.5 3.0 2.7  −10 −15 −12 TYP. 14      −7 MAX. 17   0.5 +6 +6  Unit mA GHz GHz GHz dBm dBm dBm 4 µ PB1510GV TYPICAL CHARACTERISTICS (TA = 25°C, VCC = 5 V, unless otherwise specified) CIRCUIT CURRENT vs. SUPPLY VOLTAGE 20 No input signal ICC - Circuit Current - mA 15 TA = 25 °C 10 TA = 85 °C TA = –40 °C 5 0 0 1 2 3 4 5 6 7 VCC - Supply Voltage - V INPUT POWER vs. INPUT FREQUENCY 20 10 Pin - Input Power - dBm INPUT POWER vs. INPUT FREQUENCY 20 10 Pin - Input Power - dBm TA = 25 °C TA = –40 °C TA = 25 °C 0 –10 –20 –30 –40 –50 0.1 VCC = 4.5 to 5.5 V Guaranteed operating range 0 –10 –20 –30 –40 –50 0.1 TA = 85 °C TA = 85 °C TA = 25 °C Guaranteed operating range TA = –40 °C VCC = 5 V 0.5 1 3 10 0.5 1 3 10 fin - Input Frequency - GHz fin - Input Frequency - GHz OUTPUT POWER vs. INPUT FREQUENCY 0 0 OUTPUT POWER vs. INPUT FREQUENCY Pout - Output Power - dBm Pout - Output Power - dBm TA = 85 °C –5 TA = 25 °C VCC = 5 V –5 VCC = 5.5 V TA = –40 °C –10 VCC = 4.5V –10 VCC = 5 V Pin = 0 dBm ZL = 50 Ω –15 0.1 0.5 1 3 10 –15 0.1 TA = 25 °C Pin = 0 dBm ZL = 50 Ω 0.5 1 3 10 fin - Input Frequency - GHz fin - Input Frequency - GHz 5 µ PB1510GV TYPICAL CHARACTERISTICS (TA = 25°C, VCC = 5V, unless otherwise specified) OUTPUT POWER vs. INPUT FREQUENCY 0 0 OUTPUT POWER vs. INPUT FREQUENCY Pout - Output Power - dBm Pout - Output Power - dBm VCC = 5 V –5 VCC = 5 V –5 VCC = 5.5 V VCC = 5.5 V VCC = 4.5 V –10 VCC = 4.5 V –10 TA = –40 ˚C Pin = 0 dBm ZL = 50 Ω –15 0.1 0.5 1 3 10 TA = 85 ˚C Pin = 0 dBm ZL = 50 Ω –15 0.1 0.5 1 3 10 fin - Input Frequency - GHz fin - Input Frequency - GHz S11 vs. INPUT FREQUENCY VCC = 5.0 V, TA = 25°C, ZO = 50 Ω S11 Z REF 1.0 Units 4 200.0 mUnits/ 27.159 Ω –27.582 Ω hp MARKER 4 3 GHZ Frequency (MHz) S11 (Ω) 37.1 – j207.8 14.2 – j105.1 7.9 – j35.8 27.1 – j27.5 1 : 500 MHZ 2 : 1000 MHZ 3 : 2000 MHZ 4 : 3000 MHZ 4 1 2 500 1000 2000 3000 3 START 0.500000000 GHZ STOP 3.000000000 GHZ 6 µ PB1510GV S22 vs. OUTPUT FREQUENCY VCC = 5.0V, fin = 500 MHz, TA = 25°C, ZO = 50 Ω S22 Z REF 1.0 Units 4 200.0 mUnits/ 60.925 Ω 104.77 Ω hp MARKER 4 750 MHZ 3 2 1 4 Frequency (MHz) S22 (Ω) 55.5 + j6.7 53.7 + j30.4 55.0 + j60.3 60.9 + j104.8 1 : 125 MHZ 2 : 250 MHZ 3 : 500 MHZ 4 : 750 MHZ 125 250 500 750 START 0.125000000 GHZ STOP 0.750000000 GHZ S22 vs. OUTPUT FREQUENCY VCC = 5.0V, fin = 3 GHz, TA = 25°C, ZO = 50 Ω S22 Z REF 1.0 Units 4 200.0 mUnits/ 15.613 Ω 98.168 Ω hp 4 MARKER 4 750 MHZ 2 1 1 : 125 MHZ 2 : 250 MHZ 3 : 500 MHZ 4 : 750 MHZ 3 Frequency (MHz) 125 250 500 750 S22 (Ω) 28.5 + j11.5 27.6 + j23.6 20.5 + j50.7 15.6 + j98.2 START 0.125000000 GHZ STOP 0.750000000 GHZ 7 µ PB1510GV TEST CIRCUIT Supply Voltage 1000 pF 5 V±0.5 V 1000 pF 1 Signal Generator 50 Ω C1 1000 pF 2 C2 HP8665A 3 1000 pF C3 4 5 6 OPEN 7 C4 8 OPEN 1000 pF Counter HP5350B (Spectrum Analyzer) 50 Ω 8 µ PB1510GV ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD 1P VCC IN IN C2 C1 OUT C3 C4 OUT ,,, ,,,,,,, ,,,,,,, , ,,, ,, µ PB1506/08/09GV COMPONENT LIST Symbol C1 to C4 Value 1000 pF EVALUATION BOARD CHARACTERS (1) 35 µm thick double-sided copper clad 50 × 50 × 0.4 mm polyimide board (2) Back side: GND pattern (3) Solder plated patterns (4) ° (5) : Through holes of pin 3 : partern should be removed. of pin 5 : short chip must be attached to be grounded. The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. ,, ,,,, ,, (6) 9 µ PB1510GV PACKAGE DIMENSIONS 8 PIN PLASTIC SSOP (175 mil) (UNIT: mm) 8 5 1 4 4.94±0.2 3.0 MAX. 3.2±0.1 3° –3° +7° 0.87±0.2 1.8 MAX. 1.5±0.1 0.65 0.15–0.05 0.5±0.2 0.1±0.1 0.575 MAX. 0.3 –0.05 +0.10 +0.10 0.10 M 0.15 10 µ PB1510GV NOTE CORRECT USE (1) Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as wide as possible to minimize ground impedance (to prevent undesired operation). (3) Keep the wiring length of the ground pins as short as possible. (4) Connect a bypass capacitor (e.g. 1 000 pF) to the VCC pin. RECOMMENDED SOLDERING CONDITIONS This product should be soldered under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your NEC sales representative. Soldering Method Infrared Reflow Soldering Conditions Package peak temperature: 235 °C or below Time: 30 seconds or less (at 210 °C) Note Count: 3, Exposure limit : None Package peak temperature: 215 °C or below Time: 40 seconds or less (at 200 °C) Note Count: 3, Exposure limit : None Soldering bath temperature: 260 °C or below Time: 10 seconds or less Note Count: 1, Exposure limit : None Pin temperature: 300 °C Time: 3 seconds or less (per side of device) Note Exposure limit : None Recommended Condition Symbol IR35-00-3 VPS VP15-00-3 Wave Soldering WS60-00-1 Partial Heating – Note After opening the dry pack, keep it in a place below 25 °C and 65 % RH for the allowable storage period. Caution Do not use different soldering methods together (except for partial heating). For details of recommended soldering conditions for surface mounting, refer to information document SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL (C10535E). 11 µ PB1510GV ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. NESAT (NEC Silicon Advanced Technology) is a trademark of NEC Corporation. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96. 5