UPC3224TB

DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUIT µPC3224TB 5 V, SILICON MMIC WIDEBAND AMPLIFIER DESCRIPTION The µPC3224TB is a silicon monolithic IC designed as IF amplifier for DBS tuners. This IC is manufactured using our 30 GHz fmax UHS0 (Ultra High Speed Process) silicon bipolar process. FEATURES • Wideband response : fu = 3.2 GHz TYP. @ 3 dB bandwidth • Low current • Power gain • Supply voltage • Port impedance : ICC = 9.0 mA TYP. : GP = 21.5 dB TYP. @ f = 1.0 GHz : GP = 21.5 dB TYP. @ f = 2.2 GHz : VCC = 4.5 to 5.5 V : input/output 50 Ω APPLICATION • IF amplifiers in DBS converters etc. ORDERING INFORMATION Part Number Package 6-pin super minimold Marking C3K Supplying Form • Embossed tape 8 mm wide • 1, 2, 3 pins face the perforation side of tape • Qty 3 kpcs/reel µPC3224TB-E3 Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: µPC3224TB Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC Compound Semiconductor Devices representative for availability and additional information. Document No. PU10490EJ01V0DS (1st edition) Date Published May 2004 CP(K) Printed in Japan  NEC Compound Semiconductor Devices 2004 µPC3224TB PIN CONNECTIONS Pin No. Pin Name INPUT GND GND OUTPUT GND VCC (Top View) (Bottom View) 4 5 6 4 5 6 3 2 1 1 2 3 4 5 6 3 2 1 PRODUCT LINE-UP OF 5 V-BIAS SILICON MMIC MEDIUM WIDEBAND AMPLIFIER (TA = +25°C, f = 1 GHz, VCC = Vout = 5.0 V, ZS = ZL = 50 Ω) fu (GHz) 2.9 2.6 Note C3K Part No. PO (sat) (dBm) +1.0 +3.0 +3.5 +4.0 GP (dB) 13 20 20.5 21.5 NF (dB) 5.0 4.5 2.3 4.3 ICC (mA) 12 12 14 9.0 Package 6-pin super minimold Marking C1G C1H C3H C3K µPC2711TB µPC2712TB µPC3215TB µPC3224TB 2.9 3.2 Note µPC3215TB is f = 1.5 GHz Remark Typical performance. Please refer to ELECTRICAL CHARACTERISTICS in detail. 2 Data Sheet PU10490EJ01V0DS µPC3224TB PIN EXPLANATIONS PIN No. 1 Pin Name INPUT Applied Voltage (V) – Pin Voltage Note (V) 0.91 Signal input pin. A internal matching circuit, configured with resistors, enables 50 Ω connection over a wide band. A multi-feedback circuits is designed to cancel the deviations of hFE and resistance. This pin must be coupled to signal source with capacitor for DC cut. 4 OUTPUT – 4.42 Signal output pin. A internal matching circuit, configured with resistors, enables 50 Ω connection over a wide band. This pin must be coupled to next stage with capacitor for DC cut. 6 VCC 4.5 to 5.5 – Power suplly pin. This pin should be externally equipped with bypass capacitor to minimize its impedance. 2 3 5 GND 0 – Ground pin. This pin should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be connected together with wide ground pattern to decrease impedance difference. Function and Applications Note Pin Voltage is measured at VCC = 5.0 V Data Sheet PU10490EJ01V0DS 3 µPC3224TB ABSOLUTE MAXIMUM RATINGS Parameter Supply Voltage Total Circuit Current Power Dissipation Operating Ambient Temperature Storage Temperature Input Power Symbol VCC ICC PD TA Tstg Pin TA = +25°C TA = +25°C TA = +25°C TA = +85°C Note Conditions Ratings 6.0 25 270 −40 to +85 −55 to +150 +10 Unit V mA mW °C °C dBm Note Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB RECOMMENDED OPERATING RANGE Parameter Supply Voltage Operating Ambient Temperature Symbol VCC TA Conditions MIN. 4.5 −40 TYP. 5.0 +25 MAX. 5.5 +85 Unit V °C ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC = 5.0 V, ZS = ZL = 50 Ω) Parameter Circuit Current Power Gain Symbol ICC GP Test Conditions No input signal f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Saturated Output Power PO (sat) f = 1.0 GHz, Pin = −5 dBm f = 2.2 GHz, Pin = −5 dBm Gain 1 dB Compression Output Power Noise Figure NF PO (1 dB) f = 1.0 GHz f = 2.2 GHz f = 1.0 GHz f = 2.2 GHz Upper Limit Operating Frequency Isolation fu ISL 3 dB down below flat gain at f = 0.1 GHz f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Input Return Loss RLin f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Output Return Loss RLout f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Gain Flatness MIN. 7.0 19.0 18.5 +1.5 −1.5 −6.5 −8.5 − − 2.8 35.0 37.0 9.0 10.0 11.0 8.0 − TYP. 9.0 21.5 21.5 +4.0 +1.5 −3.5 −5.5 4.3 4.3 3.2 40.0 42.0 12.0 14.0 17.0 12.0 ±0.8 MAX. 12.0 24.0 24.5 − − − − 5.8 5.8 − − − − − − − − dB dB dB GHz dB dB dBm dBm Unit mA dB ∆GP f = 0.1 to 2.2 GHz 4 Data Sheet PU10490EJ01V0DS µPC3224TB OTHER CHARACTERISTICS, FOR REFERENCE PURPOSES ONLY (TA = +25°C, VCC = 5.0 V, ZS = ZL = 50 Ω) Parameter Output Intercept Point Symbol OIP3 Test Conditions f = 1.0 GHz f = 2.2 GHz Reference Value +7.0 +5.5 Unit dBm Data Sheet PU10490EJ01V0DS 5 µPC3224TB TEST CIRCUIT VCC C4 1 000 pF 1 000 pF C3 6 50 Ω IN C1 100 pF 1 4 C2 100 pF 50 Ω OUT 2, 3, 5 The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. COMPONENTS OF TEST CIRCUIT FOR MEASURING ELECTRICAL CHARACTERISTICS Type C1, C2 C3 C4 Chip Capacitor Chip Capacitor Feed-through Capacitor Value 100 pF 1 000 pF 1 000 pF CAPACITORS FOR THE VCC, INPUT AND OUTPUT PINS Capacitors of 1000 pF are recommendable as the bypass capacitor for the VCC pin and the coupling capacitors for the input and output pins. The bypass capacitor connected to the VCC pin is used to minimize ground impedance of VCC pin. So, stable bias can be supplied against VCC fluctuation. The coupling capacitors, connected to the input and output pins, are used to cut the DC and minimize RF serial impedance. Their capacitances are therefore selected as lower impedance against a 50 Ω load. The capacitors thus perform as high pass filters, suppressing low frequencies to DC. To obtain a flat gain from 100 MHz upwards, 1 000 pF capacitors are used in the test circuit. In the case of under 10 MHz operation, increase the value of coupling capacitor such as 10 000 pF. Because the coupling capacitors are determined by equation, C = 1/(2 πRfc). 6 Data Sheet PU10490EJ01V0DS µPC3224TB ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD AMP-2 IN C1 C2 OUT C3 VCC C4 COMPONENT LIST Value C1, C2 C3, C4 100 pF 1 000 pF Notes 1. 2. 3. 4. 30 × 30 × 0.4 mm double sided copper clad polyimide board. Back side: GND pattern Solder plated on pattern : Through holes Data Sheet PU10490EJ01V0DS 7 µPC3224TB TYPICAL CHARACTERISTICS (TA = +25°C , unless otherwise specified) CIRCUIT CURRENT vs. OPERATING AMBIENT TEMPERATURE 12 11 Circuit Current ICC (mA) CIRCUIT CURRENT vs. SUPPLY VOLTAGE 16 14 Circuit Current ICC (mA) No input signal No input signal VCC = 5.0 V 12 10 8 6 4 2 0 0 1 2 3 4 TA = − 40˚C 5 6 TA = +25˚C TA = +85˚C 10 9 8 7 6 − 60 − 40 − 20 0 +20 +40 +60 +80 +100 Supply Voltage VCC (V) Operating Ambient Temperature TA (°C) POWER GAIN vs. FREQUENCY 25 TA = +25˚C Input Return Loss RLin (dB) INPUT RETURN LOSS vs. FREQUENCY 10 TA = +25˚C 23 Power Gain GP (dB) VCC = 5.5 V 21 VCC = 5.0 V 19 VCC = 4.5 V 17 0 − 10 − 20 − 30 VCC = 5.0 V VCC = 5.5 V VCC = 4.5 V 1.1 2.1 3.1 4.1 5.1 15 0.1 1.1 2.1 3.1 4.1 5.1 0.1 Frequency f (GHz) Frequency f (GHz) ISOLATION vs. FREQUENCY 0 − 20 Isolation ISL (dB) OUTPUT RETURN LOSS vs. FREQUENCY 10 TA = +25˚C TA = +25˚C Output Return Loss RLout (dB) 0 − 10 VCC = 4.5 V − 20 − 30 0.1 1.1 VCC = 5.0 to 5.5 V 2.1 3.1 4.1 5.1 − 40 − 60 VCC = 4.5 to 5.5 V − 80 − 100 0.1 1.1 2.1 3.1 4.1 5.1 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. 8 Data Sheet PU10490EJ01V0DS µPC3224TB POWER GAIN vs. FREQUENCY 25 VCC = 5.0 V 23 Power Gain GP (dB) Input Return Loss RLin (dB) INPUT RETURN LOSS vs. FREQUENCY 10 VCC = 5.0 V 21 TA = − 40˚C 0 − 10 − 20 − 30 0.1 1.1 TA = +25 to +85˚C 19 TA = +85˚C TA = − 40˚C 17 TA = +25˚C 1.1 2.1 3.1 4.1 5.1 15 0.1 2.1 3.1 4.1 5.1 Frequency f (GHz) Frequency f (GHz) ISOLATION vs. FREQUENCY 0 − 20 Isolation ISL (dB) OUTPUT RETURN LOSS vs. FREQUENCY 10 VCC = 5.0 V VCC = 5.0 V Output Return Loss RLout (dB) 0 − 10 − 20 TA = +25˚C − 30 0.1 1.1 2.1 TA = − 40˚C 3.1 4.1 5.1 − 40 − 60 − 80 TA = +85˚C TA = − 40 to +85˚C − 100 0.1 1.1 2.1 3.1 4.1 5.1 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. Data Sheet PU10490EJ01V0DS 9 µPC3224TB OUTPUT POWER vs. INPUT POWER 10 5 0 −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) f = 1.0 GHz TA = +25˚C VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V Output Power Pout (dBm) OUTPUT POWER vs. INPUT POWER 10 5 0 TA = − 40˚C −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) f = 1.0 GHz VCC = 5.0 V TA = +25 to +85˚C Output Power Pout (dBm) 0 5 10 0 5 10 OUTPUT POWER vs. INPUT POWER 10 5 0 −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) f = 2.2 GHz TA = +25˚C Output Power Pout (dBm) OUTPUT POWER vs. INPUT POWER 10 5 0 −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) TA = − 40˚C f = 2.2 GHz VCC = 5.0 V TA = +25 to +85˚C Output Power Pout (dBm) VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V 0 5 10 0 5 10 Output Power (2 tones) Pout (dBm) 3rd Order Intermodulation Distortion IM3 (dBm) 10 Output Power (2 tones) Pout (dBm) 3rd Order Intermodulation Distortion IM3 (dBm) OUTPUT POWER (2 tones), IM3 vs. INPUT POWER f1 = 1 000 MHz 0 f2 = 1 001 MHz Pout 5.5 V VCC = 5.5 V 5.0 V 4.5 V 5.0 V 4.5 V OUTPUT POWER (2 tones), IM3 vs. INPUT POWER 10 f1 = 2 200 MHz 0 f2 = 2 201 MHz Pout VCC = 5.5 V 5.0 V 4.5 V 5.5 V 5.0 V 4.5 V − 10 − 20 − 30 − 40 − 50 VCC = 4.5 V − 60 − 70 − 10 − 20 − 30 − 40 − 50 − 60 − 70 IM3 IM3 VCC = 5.5 V 0 VCC = 5.0 V − 80 − 50 − 45 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) − 80 − 50 − 45 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) 0 Remark The graphs indicate nominal characteristics. 10 Data Sheet PU10490EJ01V0DS µPC3224TB S-PARAMETERS (TA = +25°C, VCC = 5.0 V) S11−FREQUENCY 2.2 GHz 1.0 GHz S22−FREQUENCY 1.0 GHz 2.2 GHz Data Sheet PU10490EJ01V0DS 11 µPC3224TB PACKAGE DIMENSIONS 6-PIN SUPER MINIMOLD (UNIT: mm) 2.1±0.1 1.25±0.1 2.0±0.2 1.3 0.65 0.65 0.1 MIN. 0.9±0.1 0.7 12 Data Sheet PU10490EJ01V0DS 0 to 0.1 0.15+0.1 –0.05 0.2+0.1 –0.05 µPC3224TB NOTES ON CORRECT USE (1) Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation). All the ground pins must be connected together with wide ground pattern to decrease impedance difference. (3) The bypass capacitor should be attached to VCC line. (4) The DC cut capacitor must be each attached to input and output pin. RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below : 260°C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260 For soldering Preheating temperature (package surface temperature) : 120°C or below Caution Do not use different soldering methods together (except for partial heating). Data Sheet PU10490EJ01V0DS 13 µPC3224TB • The information in this document is current as of May, 2004. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation, NEC Compound Semiconductor Devices, Ltd. and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4 - 0110 14 Data Sheet PU10490EJ01V0DS µPC3224TB For further information, please contact NEC Compound Semiconductor Devices, Ltd. http://www.ncsd.necel.com/ E-mail: salesinfo@ml.ncsd.necel.com (sales and general) techinfo@ml.ncsd.necel.com (technical) 5th Sales Group, Sales Division TEL: +81-44-435-1588 FAX: +81-44-435-1579 NEC Compound Semiconductor Devices Hong Kong Limited E-mail: ncsd-hk@elhk.nec.com.hk (sales, technical and general) FAX: +852-3107-7309 TEL: +852-3107-7303 Hong Kong Head Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Taipei Branch Office FAX: +82-2-558-5209 TEL: +82-2-558-2120 Korea Branch Office NEC Electronics (Europe) GmbH http://www.ee.nec.de/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 0401