NSSM009XT

No. STSE-CM6042A SPECIFICATIONS FOR NICHIA CHIP TYPE FULL COLOR MODEL : NSSM009BT LED NICHIA CORPORATION -0- Nichia STSE-CM6042A 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Reverse Voltage Power Dissipation Total Power Dissipation Operating Temperature Storage Temperature Soldering Temperature Symbol IF IFP VR PD Ptot Topr Tstg Tsld Absolute Maximum Rating Blue Green Red 35 35 50 110 110 200 5 123 123 125 280 -30 ~ + 85 -40 ~ +100 Reflow Soldering : 260°C for 10sec. Hand Soldering : 350°C for 3sec. (Ta=25°C) Unit mA mA V mW mW °C °C IFP Conditions : Pulse Width < 10msec. and Duty < 1/10 = = Value for one LED device (Single color). Value for total power dissipation when two and more devices are lit simultaneously. (2) Initial Electrical/Optical Characteristics Item Forward Voltage Reverse Current Luminous Intensity Chromaticity Coordinate x y Symbol Condition IF=20[mA] VR= 5[V] IF=20[mA] IF=20[mA] IF=20[mA] Blue Typ. Max. 3.5 50 (3.2) (400) 0.133 0.075 (Ta=25°C) Green Typ. (3.2) (1200) 0.189 0.718 Max. 3.5 50 - Red Typ. (2.1) (700) 0.700 0.299 Max. 2.5 50 - Unit VF IR Iv - V µA mcd - Please refer to CIE 1931 chromaticity diagram. (3) Ranking Item Luminous Intensity Symbol Condition IF=20[mA] Blue Min. Max. 560 280 (Ta=25°C) Green Min. 800 Max. 1600 380 Red Min. Max. 1080 Unit Iv mcd Luminous Intensity Measurement allowance is ± 10%. Color Ranks Blue (IF=20mA, Ta=25°C) Rank W 0.113 0.134 0.080 0.105 Rank G0d 0.176 0.220 0.750 0.745 x y Green 0.139 0.035 0.129 0.050 0.145 0.072 0.152 0.056 x y 0.190 0.628 0.136 0.739 0.250 0.638 -1- 0.219 0.637 Nichia STSE-CM6042A Red x y 0.674 0.296 Rank R 0.648 0.677 0.323 0.323 0.708 0.292 Color Coordinates Measurement allowance is ± 0.01. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure’s page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure’s page. Package Material as follows ; Encapsulating Resin Electrodes : : : Heat-Resistant Polymer Epoxy Resin (Diffused) Ag Plating Copper Alloy 4.PACKAGING · The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; Year ( 5 for 2005, 6 for 2006 ) Month ( 1 for Jan., 9 for Sep., A for Oct., Nichia's Product Number B for Nov. ) -2- Nichia STSE-CM6042A 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Resistance to Soldering Heat (Reflow Soldering) Thermal Shock Temperature Cycle Moisture Resistance Cyclic High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Standard Test Method JEITA ED-4701 300 301 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) 0°C ~ 100°C 15sec. 15sec. -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. 25°C ~ 65°C ~ -10°C 90%RH 24hrs./1cycle Ta=100°C Ta=60°C, RH=90% Ta=-40°C Ta=25°C, B IF=13mA G IF=32mA R IF=21mA Note 2 times Number of Damaged 0/50 100 cycles 100 cycles 10 cycles 500hrs. 500hrs. 500hrs. 500hrs. 0/50 0/50 0/50 0/50 0/50 0/50 0/50 Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Value for one LED device (Single color). 60°C, RH=90%, B IF=8.5mA G IF=18mA R IF=14.5mA Ta=-30°C, B IF=13mA G IF=32mA R IF=21mA 500hrs. 0/50 500hrs. 0/50 (2) CRITERIA FOR JUDGING DAMAGE (Value for one LED device (Single color).) Criteria for Judgement Min. Max. Item Symbol Test Conditions Forward Voltage Reverse Current Luminous Intensity VF IR IV B,G,R IF=20mA B,G,R VR=5V B,G,R IF=20mA L.S.L.**) 0.7 U.S.L.*) 1.1 U.S.L.*) 2.0 - *) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level -3- Nichia STSE-CM6042A-1 7.CAUTIONS (1) Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. · The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : more than 24 hours at 65 ± 5°C · Nichia LED electrodes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · During operation of the LEDs the total power dissipation of the diode elements (red, green, and blue) within the LEDs must not exceed the maximum power dissipation. · The operating current should be decided after considering the ambient maximum temperature of LEDs. -4- Nichia STSE-CM6042A-1 (4) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200°C 120 ~ 150°C 120 sec. Max. 120 sec. Max. 240°C Max. 260°C Max. 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Hand Soldering Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. 2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 60sec.Max. Above 200°C 120sec.Max. 240°C Max. 10sec. Max. 1 ~ 5°C / sec. 1 ~ 5°C / sec. Pre-heating 180 ~ 200°C 60sec.Max. Above 220°C 260°C Max. 10sec. Max. 2.5 ~ 5°C / sec. 120sec.Max. [Recommended soldering pad design] 1.7 Use the following conditions shown in the figure. 1.7 1.4 5.6 3 2.75 8.75 3 (Unit : mm) · Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. · After soldering, do not warp the circuit board. (5) Cleaning · It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. -5- Nichia STSE-CM6042A-1 (6) Static Electricity · Static electricity or surge voltage damages the Blue/Green LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) (7) Others · NSSM009B complies with RoHS Directive. · Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating when using the LEDs with matrix drive. · The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. · Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice. -6- Nichia STSE-CM6042A ICI Chromaticity Diagram 0.9 520 530 0.8 540 510 0.7 G0d 550 560 0.6 570 500 0.5 580 590 y 0.4 600 610 620 630 0.3 490 R 0.2 0.1 480 W 470 460 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 x Color Coordinates Measurement allowance is ± 0.01. -7- Forward Voltage vs. Forward Current 200 Forward Current IFP (mA) 100 50 20 10 5 BLUE GREEN RED Forward Current vs. Relative Luminosity Allowable Forward Current IFP (mA) (Ta=25°C) Duty Ratio vs. Allowable Forward Current (Ta=25°C) 6 Relative Luminosity (a.u.) 5 4 3 2 1 0 0 BLUE GREEN RED 300 200 110 50 35 20 10 1 BLUE, GREEN RED (Ta=25°C) 1 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8 Forward Voltage VF (V) 20 40 60 80 100 120 Forward Current IFP (mA) 5 10 20 50 100 Duty Ratio (%) Ambient Temperature vs. Forward Voltage 4.4 Forward Voltage VF (V) 4.0 3.6 3.2 2.8 2.4 2.0 1.6 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) (IFP=20mA) Ambient Temperature vs. Relative Luminosity 2.0 Relative Luminosity (a.u.) (IFP=20mA) BLUE GREEN RED Ambient Temperature vs. Power Dissipation 140 Power Dissipation PD (mW) 120 100 80 60 40 20 0 0 BLUE, GREEN RED Ambient Temperature vs. Power Dissipation Total Power Dissipation Ptot (mW) 350 300 250 200 150 100 50 0 0 20 40 60 80 100 Ambient Temperature Ta (°C) BLUE GREEN RED -8- 1.0 0.5 0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) 20 40 60 80 100 Ambient Temperature Ta (°C) Nichia STSE-CM6042A (NOTE) The value for one device should be within the absolute maximum rating when one or two and more devices are lit (Full color). Total value should be within the absolute maximum rating when two and more devices are lit (Full color). Model NSSM009B NICHIA CORPORATION Title No. CHARACTERISTICS 060403651181 Spectrum Relative Emission Intensity (a.u.) (Ta=25°C, IF=20mA) Directivity X-X 1.2 1.0 0.8 0.6 0.4 0.2 0 400 450 500 550 600 650 700 Wavelength λ (nm) 1.0 (Ta=25°C, IFP=20mA) Y-Y 1.0 (Ta=25°C, IFP=20mA) Y X Y X Relative Luminosity (a.u.) BLUE GREEN RED 0.5 Relative Luminosity (a.u.) 0.5 BLUE GREEN RED 0 -90° -60° -30° 0° 30° 60° 90° Radiation Angle 0 -90° -60° -30° 0° 30° 60° 90° Radiation Angle -9- Nichia STSE-CM6042A Model NSSM009B NICHIA CORPORATION Title No. CHARACTERISTICS 060403651191 5.5 (R 1) 5.1 1.1 4 (0.95) (0.95) 3 Red 3.56 Green Blue 5.5 5 6 2 1 (4) (3.6) (C 0.6 ) 1 Pin Mark (0.4) 2.5 ± 0.3 (1.3) -10- 4 5 6 Red Green Blue 3 2 1 ITEM MATERIALS PACKAGE Heat-Resistant Polymer ENCAPSULATING RESIN Epoxy Resin (Diffused) ELECTRODES Ag Plating Copper Alloy Nichia STSE-CM6042A 1.17 ± 0.3 (1.9) Model NSSM009B Unit mm 10/1 Scale Allow ±0.2 Red LED die and blue LED die are mounted on the cathode side, green LED die is mounted on the anode side. NICHIA CORPORATION Title No. OUTLINE DIMENSIONS 060403651201 Taping part φ 1.5+0.1 -0 8±0.1 2±0.05 4±0.1 1.75±0.1 0.31±0.05 Reel part φ 330±0.2 17.5±1 13.5±0.5 5.5±0.05 12+0.3 - 0.1 5.76±0.1 φ2 1 ±0.8 ±0.2 φ 13 1 Pin Mark 5.76±0.1 φ 2.75±0.1 1.5+0.2 -0 Label 3in1 LED TYPE NSSM009xT LOT XXXXXX QTY pcs Reel end of tape No LEDs LEDs mounting part No LEDs φ 80±1 -11Pull direction Top cover tape Embossed carrier tape Reel Lead Min.40mm (No LEDs) Reel Lead Min.320mm (No LEDs is more than 40) Reel Lead Min.400mm Nichia STSE-CM6042A 3,000pcs/Reel Model Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. NSSM009xT Unit mm Scale Allow NICHIA CORPORATION Title No. TAPING DIMENSIONS 050413309253 Nichia STSE-CM6042A The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Moisture proof foil bag Reel Label Seal NICHIA 3in1 LED TYPE LOT QTY NSSM009xT xxxxxx PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Moisture absorbent material The box is partitioned with the cardboard. Label NICHIA Nichia LED TYPE QTY 3in1 LED NSSM009xT PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Reel/bag 1reel Quantity/bag (pcs) 3,000 MAX. Reel/box 5reel MAX. Quantity/box (pcs) 15,000 MAX. Dimensions (mm) 391 379 149 8t Model NSSM009xT NICHIA CORPORATION Title No. PACKING 050524540321 -12-