PCR0J331MCL1GS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCR Chip Type, High Reliability High reliability, High voltage (to 80V). Low ESR, High ripple current. Long life of 4000 hours at 125°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Adapted to the RoHS directive (2011/65/EU). ESR after Endurance at -40°C. PCR High Capacitance Long Life Assurance PCX Specifications Item Performance Characteristics Category Temperature Range – 55 to +125°C Rated Voltage Range 16 to 80V Rated Capacitance Range 22 to 1000µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C 1) ESR ( Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(µA), whichever is greater. Temperature Characteristics (Max.Impedance Ratio) Z+125°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 125°C. 1.25 1.25 (100kHz) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Shelf Life ESR after Endurance ( 1) Less than or equal to the specified value at 100kHz, -40°C Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C, 85% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Plastic platform Lot No. C±0.2 0.3 MAX. 1 0.5 MAX. Capacitance Type numbering system (Example : 35V 150µF) Positive Dimensions 2 3 4 5 6 7 8 9 10 11 12 13 14 PCR 1 V 1 5 1 MC L 1 GS Taping code A±0.2 Capacitance tolerance (±20%) Rated capacitance (150µF) Rated voltage (35V) L +0.1 -0.4 Voltage (V:35V) Series E B±0.2 φD±0.5 CR 150 V 331 Size code Configuration Negative H Series name Type (mm) Size φD φ8 × 7L φ8 × 10L φ8 × 12L φ10 × 8L φ10 ×10L φ10×12.7L 8.0 8.0 8.0 10.0 10.0 10.0 L 6.9 9.9 11.9 7.9 9.9 12.6 A 9.0 9.0 9.0 11.0 11.0 11.0 B 8.3 8.3 8.3 10.3 10.3 10.3 C 8.3 8.3 8.3 10.3 10.3 10.3 3.2 3.2 3.2 4.6 4.6 4.6 E H 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 φ8 × 10L, φ10 × 10L : The vibration structure-resistant product is also available upon request, please ask for details. Voltage V 16 20 25 35 50 63 80 Code C D E V H J K Dimension table in next page. 47 CAT.8100F CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCR Standard Ratings Rated Voltage (V)(code) 16 (1C) Surge Voltage (V) 25 (1E) 35 (1V) 50 (1H) 63 (1J) 80 (1K) 31 63 79 100 60 1500 PCR1C221MCL1GS 17 34 3400 PCR1C471MCL6GS 8 × 10 10 × 8 Rated Ripple (mArms) Part Number (125°C / 100kHz) 0.08 32 64 2200 PCR1C471MCL1GS 560 8 × 12 0.08 16 32 3800 PCR1C561MCL1GS 680 10 × 10 0.08 19 38 3200 PCR1C681MCL1GS 10 × 12.7 0.08 13 26 4300 PCR1C102MCL1GS 150 8×7 0.08 39 78 1200 PCR1D151MCL1GS 330 8 × 10 0.08 19 38 3300 PCR1D331MCL6GS 0.08 33 66 2100 PCR1D331MCL1GS 10 × 8 470 8 × 12 0.08 18 36 3500 PCR1D471MCL1GS 560 10 × 10 0.08 20 40 3100 PCR1D561MCL1GS 680 10 × 12.7 0.08 14 28 4200 PCR1D681MCL1GS 100 8×7 0.08 41 82 1200 PCR1E101MCL1GS 220 8 × 10 0.08 20 40 3200 PCR1E221MCL6GS 0.08 33 66 2100 PCR1E221MCL1GS 220 10 × 8 270 8 × 12 0.08 19 38 3300 PCR1E271MCL1GS 330 10 × 10 0.08 20 40 3100 PCR1E331MCL1GS 470 10 × 12.7 0.08 15 30 4100 PCR1E471MCL1GS 68 8×7 0.08 44 88 1200 PCR1V680MCL1GS 150 8 × 10 0.08 22 44 3100 PCR1V151MCL6GS 0.08 33 66 2100 PCR1V151MCL1GS 150 43 30 0.08 8×7 470 330 25 0.08 220 1000 20 (1D) Low temp. ESR after Endurance (mΩ) (-40°C / 100kHz) tan δ 470 20 Initial ESR (mΩ) (20°C / 100kHz) Case Size φD × L (mm) Rated Capacitance (µF) 10 × 8 220 8 × 12 0.08 21 42 3300 PCR1V221MCL1GS 270 10 × 10 0.08 20 40 3100 PCR1V271MCL1GS 330 10 × 12.7 0.08 16 32 3900 PCR1V331MCL1GS 39 8×7 0.08 45 90 1300 PCR1H390MCL1GS 82 8 × 10 0.08 26 52 2900 PCR1H820MCL6GS 0.08 42 84 1900 PCR1H820MCL1GS 82 10 × 8 120 8 × 12 0.08 25 50 2900 PCR1H121MCL2GS 120 10 × 10 0.08 25 50 3000 PCR1H121MCL1GS 180 10 × 12.7 0.08 19 38 3500 PCR1H181MCL1GS 22 8×7 0.08 48 96 1100 PCR1J220MCL1GS 39 8 × 10 0.08 28 56 2700 PCR1J390MCL1GS 0.08 47 94 1800 PCR1J470MCL1GS 47 10 × 8 56 8 × 12 0.08 27 54 2900 PCR1J560MCL1GS 68 10 × 10 0.08 28 56 2800 PCR1J680MCL1GS 100 10 × 12.7 0.08 24 48 3000 PCR1J101MCL1GS 27 8 × 10 0.08 38 76 1400 PCR1K270MCL1GS 39 8 × 12 0.08 35 70 1600 PCR1K390MCL1GS 47 10 × 10 0.08 33 66 1700 PCR1K470MCL1GS 68 10 × 12.7 0.08 28 56 2100 PCR1K680MCL1GS Rated ripple current (mArms) at 125°C 100kHz No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 48 CAT.8100F