PCS0J470MCL1GS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCS Chip Type, LongLife Assurance Load life of 5000 hours at 105°C. SMD type : Lead free reflow soldering condition at 　 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. PCL PCS Long Life Long Life PCF Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 4 to 16V Rated Capacitance Range 22 to 560µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value . 1.25 1.25 After 2 minutes' application of rated voltage at 20°C (100kHz) Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Positive B±0.2 C±0.2 Type numbering system (Example : 6.3V 220µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PCS 0 J 2 2 1 MC L 1 GS Taping code Size code A±0.2 0.3 MAX. φD±0.5 CS 220 j 941 Lot No. E Capacitance 0.5 MAX. Plastic platform Configuration Capacitance tolerance (±20%) Series L +0.1 -0.4 Voltage ( j:6.3v) Rated capacitance (220µF) Negative H Rated voltage (6.3V) Series name Size φD L A B C E H Type (mm) φ8 × 7L 8.0 φ5 × 6L 5.0 φ6.3 × 6L 6.3 5.9 5.9 6.9 6.0 7.3 9.0 5.3 5.3 6.6 6.6 8.3 8.3 1.6 2.1 3.2 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 Dimension table in next page. Voltage V 4 6.3 10 16 Code g j A C Frequency coefficient of rated ripple current 0 Frequency0/ 120Hz Coefficient 0.05 1kHz 0.30 10kHz 100kHz or more 0.70 1.00 CAT.8100K CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCS Dimensions Rated Voltage (V) (code) 4 (0G) 6.3 (0J) 10 (1A) 16 (1C) Surge Voltage (V) 4.6 7.2 11.5 18.4 Case Size φD × L (mm) tan δ 150 5×6 0.12 Leakage Current (µA) at 20°C after 2 minutes 120 25 2200 PCS0G151MCL1GS 330 6.3 × 6 0.12 264 20 2800 PCS0G331MCL1GS 330 8×7 0.12 264 22 3200 PCS0G331MCL9GS 560 8×7 0.12 448 18 3600 PCS0G561MCL1GS 47 5×6 0.12 100 35 1600 PCS0J470MCL1GS 100 5×6 0.12 126 25 2400 PCS0J101MCL1GS 100 6.3 × 6 0.12 126 22 2800 PCS0J101MCL9GS 120 6.3 × 6 0.12 151 22 2800 PCS0J121MCL9GS 220 6.3 × 6 0.12 277 20 2800 PCS0J221MCL1GS 220 8×7 0.12 277 22 3200 PCS0J221MCL9GS 390 8×7 0.12 491 22 3200 PCS0J391MCL1GS 33 5×6 0.12 100 40 1300 PCS1A330MCL1GS 56 6.3 × 6 0.12 112 27 2300 PCS1A560MCL9GS 68 5×6 0.12 136 30 2100 PCS1A680MCL1GS 120 6.3 × 6 0.12 240 27 2300 PCS1A121MCL1GS 150 8×7 0.12 300 30 2600 PCS1A151MCL9GS 270 8×7 0.12 540 22 3200 PCS1A271MCL1GS 22 5×6 0.12 100 45 1100 PCS1C220MCL1GS 39 5×6 0.12 125 35 2000 PCS1C390MCL1GS 39 6.3 × 6 0.12 125 30 2200 PCS1C390MCL9GS 68 6.3 × 6 0.12 218 30 2200 PCS1C680MCL1GS 82 8×7 0.12 262 28 2800 PCS1C820MCL9GS 120 8×7 0.12 384 28 2800 PCS1C121MCL1GS Rated Capacitance (µF) ( ) ESR Rated Ripple (mΩ) (mArms) (20°C/100kHz) (105°C/100kHz) Part Number No marked, 1 will be put at 12th digit of type numbering system. : In this case, 9 will be put at 12th digit of type numbering system. For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K