UCW1A331MCL

ALUMINUM ELECTROLYTIC CAPACITORS CW Specifications Item Chip Type, Low Impedance, Long Life Assurance series Chip type with load life of 7000 hours at +105°C. Low impedance temperature range up to +105°C. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). CW Low Impedance CB Performance Characteristics Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ – 25 ~ +105°C 6.3 ~ 50V 10 ~ 470µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.) 6.3 0.32 10 0.28 6.3 4 16 0.26 10 3 25 0.16 16 2 25 2 35 0.14 35 2 50 0.14 50 2 Measurement frequency : 120Hz Rated voltage (V) Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z– 25°C / Z+20°C Endurance After 7000 hours' application of rated voltage at 105°C , capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Within ±30% of initial value 300% or less of initial specified value Initial specified value or less Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Black print on the case top. Chip Type (φ5 ~ 6.3 ) Voltage ( C : 16V ) Series φD ± 0.5 Plastic platform 0.3MAX. C ± 0.2 B ± 0.2 0.5MAX. Positive Type numbering system (Example : 10V 150µF) U CW 1 A 1 5 1 MC L 1 G S Capacitance tolerance (±20%) Rated Capacitance (150µF) Rated voltage (10V) Series name Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L ± 0.3 Lot No. Capacitance H Negative Taping code Configuration fD Code 5 ¥ 6.3 CL 8 ¥ 10 NL (φ8 ~ 10 ) 0.5MAX. Voltage ( V : 35V ) Trade mark Series φD ± 0.5 Plastic platform 0.3MAX. C ± 0.2 A ± 0.2 A ± 0.2 A2 150C CW E Positive f D´L L ± 0.5 Lot No. Capacitance Pressure relief vent H Negative A B C E L H (mm) 5 ´ 7 6.3 ´ 7 6.3 ´ 8.7 8 ´ 10 10 ´ 10 3.2 2.9 2.4 2.4 2.1 10.3 8.3 6.6 6.6 5.3 10.3 8.3 6.6 6.6 5.3 4.5 3.1 2.2 2.2 1.3 10 10 8.7 7.0 7.0 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 Voltage V 6.3 Code j 10 A 16 C 25 E 35 V 50 H Dimension table in next page. A ± 0.2 A ± 0.2 A2 220V CW B ± 0.2 E CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS CW Cap. (µF) series Dimensions V Code 6.3 0J 10 1A 5×7 5×7 2.2 95 6.3 × 7 6.3 × 7 6.3 × 7 1.1 140 6.3 × 8.7 6.3 × 8.7 8 × 10 8 × 10 16 1C 2.2 1.1 1.1 1.0 1.0 0.22 0.22 95 140 140 230 230 600 600 8 × 10 8 × 10 10 × 10 5×7 6.3 × 7 6.3 × 7 6.3 × 8.7 25 1E 5×7 2.2 1.1 1.1 1.0 0.22 0.22 0.16 95 140 140 230 600 600 850 8 × 10 10 × 10 5×7 6.3 × 8.7 6.3 × 8.7 35 1V 2.2 2.2 1.0 1.0 95 95 230 230 8 × 10 8 × 10 0.22 0.16 600 850 10 × 10 Case size φ D × L (mm) 50 1H 10 22 33 47 100 150 220 330 470 100 220 330 470 101 151 221 331 471 6.3 × 8.7 6.3 × 8.7 8 × 10 1.0 1.0 0.22 230 230 600 5×7 6.3 × 7 2.2 1.1 95 140 0.53 0.53 0.35 Impedance 350 350 670 Rated ripple Max. impedance (Ω) at 20°C 100kHz, Rated Ripple (mArms) at 105°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V