UUP1A330MCL

ALUMINUM ELECTROLYTIC CAPACITORS UP 6mmL Chip Type, Bi-Polarized series Chip type, bi-polarized withstanding high temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). UN Extended range UP High Temperature WP Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics – 55 ~ +105°C 6.3 ~ 50V 0.1 ~ 47µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.) 6.3 0.24 10 0.20 6.3 4 8 16 0.17 10 3 6 25 0.17 16 2 4 25 2 4 35 0.15 35 2 3 50 0.15 50 2 3 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Endurance Shelf Life Resistance to soldering heat Marking After 1000 hours' application of rated Capacitance change Within ±20% of initial value voltage at 105°C with the polarity inverted tan δ 200% or less of initial specified value every 250 hours, capacitors meet the Leakage current Initial specified value or less characteristic requirements listed at right. After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Black print on the case top. Chip Type 105°C Marking Capacitance Lot No. Type numbering system (Example : 16V 10µF) 1 Plastic platform 0.3 MAX. C ± 0.2 0.5 MAX. 2 3 4 5 6 7 8 9 10 11 12 13 14 UUP 1C 1 0 0 MCL1GS Taping code A ± 0.2 φD Voltage L ± 0.3 0.5 ~ 0.8 A B C E L 4 1.8 4.3 4.3 1.0 5.8 (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 5.8 5.8 Configuration Capacitance tolerance (± 20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Type X2P 10 16V φD ± 0.5 B ± 0.2 E Voltage mark for 6.3V is 6V Dimensions Cap.(µF) V Code 6.3 0J 10 1A A ± 0.2 16 1C 25 1E 35 1V 50 1H 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 5 6.3 6.3 28 37 45 4 6.3 6.3 17 33 41 4 5 6.3 6.3 12 23 37 49 5 5 6.3 12 16 27 4 5 5 6.3 8.4 16 18 29 4 4 4 4 4 5 5 6.3 1.0 2.0 2.8 4.0 8.4 13 17 20 Case size φ D (mm) Rated ripple Rated Ripple (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UN(p.77) series if high CV products are required. Please refer to page 3 for the minimum order quantity. CAT.8100V