UWS1H681MCL

ALUMINUM ELECTROLYTIC CAPACITORS WS Chip Type, High CV High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type higher capacitance in large case size. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WS High Temperature Reflow UR Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics – 40 ~ +85°C 6.3 ~ 50V 22 ~ 1500µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) . Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.) 6.3 0.28 10 0.24 6.3 5 10 16 0.20 10 4 8 25 0.16 16 3 6 35 0.14 25 2 4 35 2 3 50 0.12 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C 50 2 3 Endurance After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Shelf Life After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C, for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Black print on the case top. Capacitance change tan δ Leakage current Resistance to soldering heat Marking Within ±10% of initial value Initial specified value or less Initial specified value or less Chip Type (φ6.3, φ8 × 6.2) Voltage (A:10V) C±0.2 0.5MAX. Plastic platform 0.3MAX. Positive Type numbering system (Example : 10V 100µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UWS 1 A 1 0 1 M C L 1G S Package code Configuration Capacitance tolerance (–20%) Rated Capacitance (100µF) Rated voltage (10V) Series name Type Series N2 100A WS φD±0.5 Lot No. Capacitance L ±0.3 H 1 Size φ8 × 6.2 only Negative A±0.2 1 Trade mark B±0.2 E A±0.2 (mm) (φ8 × 10, φ10 × 10) Positive Voltage (V:35V) Series C±0.2 0.5MAX. Plastic platform 0.3MAX. φD×L 6.3 × 5.8 2.4 6.6 6.6 2.2 5.8 0.5 ~ 0.8 6.3 × 7.7 2.4 6.6 6.6 2.2 7.7 0.5 ~ 0.8 8 × 6.2 3.3 8.3 8.3 2.3 6.2 0.5 ~ 0.8 8 × 10 2.9 8.3 8.3 3.1 10 0.8 ~ 1.1 10 × 10 3.2 10.3 10.3 4.5 10 0.8 ~ 1.1 N2 100V WS φD±0.5 B±0.2 Lot No. Capacitance L±0.5 H Negative Voltage V Code 6.3 j 10 A 16 C 25 E 35 V 50 H Dimension table in next page. A±0.2 Trade mark E A±0.2 A B C E L H CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WS Cap. (µF) series Dimensions V Code 6.3 0J 10 1A 16 1C 25 1E 6.3 × 5.8 6.3 × 5.8 65 145 192 250 305 393 8 × 6.2 8 × 10 8 × 10 10 × 10 10 × 10 35 1V 6.3 × 5.8 55 105 175 214 265 324 8 × 6.2 8 × 10 10 × 10 10 × 10 10 × 10 50 1H 45 95 140 195 238 289 22 33 47 100 150 220 330 470 680 1000 1500 220 330 470 101 151 221 331 471 681 102 152 8 × 6.2 8 × 6.2 8 × 10 8 × 10 10 × 10 10 × 10 160 190 265 318 400 489 6.3 × 5.8 6.3 × 5.8 8 × 6.2 8 × 10 8 × 10 10 × 10 10 × 10 70 85 175 240 290 374 454 8 × 6.2 6.3 × 7.7 8 × 10 8 × 10 10 × 10 10 × 10 125 151 215 270 330 396 8 × 6.2 8 × 10 10 × 10 10 × 10 10 × 10 Case size φ D × L (mm) Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 00 ~ 47V 100 ~ 1500 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz~ 1.67 1.30 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V