UZS1A470MCL

ALUMINUM ELECTROLYTIC CAPACITORS ZS 4.5mmL Chip Type series Chip type with 4.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WX Smaller ZT High Te m p e rature ZS Smaller Bi-polarized ZP Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ ZR Performance Characteristics – 40 ~ + 85°C 4 ~ 50V 0.1 ~ 220µF + 20% at 120Hz, 20°C – After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C R ated voltage (V) tan δ (MAX.) 4 0.50 6.3 0.30 10 0.24 16 0.19 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C 4 7 15 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Endurance After 2000 hours' application of rated voltage at 85°C,capacitors meet the characteristics requirements listed at right. Capacitance change tan δ Leakage current Within + 20% of initial value – 200% or less of initial specified value Initial specified value or less Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within + 10% of initial value – for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature,they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Black print on the case top. Chip Type Positive 0.5 MAX. Capacitance Lot No. Voltage Plastic platform 0.3 MAX. C + 0.2 – Type numbering system (Example : 16V 10µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UZ S 1 C 1 0 0 MC L 1GB Taping code A+ 0.2 A + 0.2 – – φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 Configuration Capacitance tolerance (+ 20%) – Rated Capacitance (10µF) Rated voltage (16V) Series name Type X2 10 16V φD+ 0.5 – B+ 0.2 – 4.5 Voltage mark for 6.3V is 6V . +0.1 –0.2 0.5 ~ 0.8 Dimensions V Cap. (µF) Code 4 0G 6.3 0J E Negative 10 1A 16 1C 25 1E 35 1V 4 4 4 4 4 4 4 5 6.3 50 1H 1.0 2.0 2.8 4.0 8.4 13 17 20 33 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 221 4 4 5 6.3 28 33 56 96 4 5 5 6.3 28 37 45 70 5 5 6.3 33 41 52 4 5 6.3 6.3 23 37 49 58 4 5 6.3 6.3 16 27 42 52 4 5 6.3 18 29 46 Case size φ D (mm) Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UR(p.70), UG(p.75) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V