FB15ANEP2-FA

.5 Amp Momentary Pushbuttons Series FB Distinctive Characteristics Optional caps in different colors to vary appearance as needed. Low operating force for ease of actuation. Rear panel bushing mount with compact behind panel dimension. Internal antijamming feature to protect the contacts from damage due to excessive force on the plunger. Self-cleaning contacts make FB models highly reliable. Low cost device of rugged one-piece bushing and housing construction. Reliability of construction with an internal guide to maintain contact alignment. Epoxy sealed terminals. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 .5 Amp Momentary Pushbuttons Series FB General Specifications FB Series Electrical Capacity (Resistive Load) Power Level: Logic Level: 500mA @ 125V AC for silver 0.4VA max. @ 28V AC/DC max. for gold (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: 30 milliohms maximum for silver; 30 milliohms maximum for gold 100 megohms minimum @ 500V DC 1,000V AC minimum between contacts & between contacts & case for 1 minute minimum 50,000 operations minimum 50,000 operations minimum 2.16N Pretravel .043” (1.1mm) Overtravel .022” (0.57mm) Total Travel .065” (1.67mm) Materials & Finishes Plunger: Bushing: Case: Movable Contactor: Stationary Contacts: Terminals: Polyacetal Brass with nickel plating Phenolic resin Copper with silver or gold plating Phosphor bronze with silver or gold plating Phosphor bronze with silver or gold plating Environmental & Installation Data Operating Temp Range: Soldering Time & Temperature: –10°C through +70°C (+14°F through +158°F) Manual Soldering: See Profile A in Supplement section. Standards & Certifications UL Recognized: Models rated 0.5A @ 125V AC Single pole; Momentary action circuit with solder lug terminations. UL File No. WOYR2.E44145; add “/U” to end of part number to order UL mark on switch. Models rated 0.5A @ 125V AC Single pole; Momentary action circuit with solder lug terminations. C-UL File No. WOYR8.E44145; add “/C-UL” to end of part number to order C-UL mark on switch. C-UL Recognized: R N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 .5 Amp Momentary Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series FB A FB 15AN EP 2 F P OLE & CIRCUIT 15AN SPST OFF (ON) ( ) = Momentary C ONTACT MATERIALS & RATINGS 2 4 Silver Contacts 500mA @ 125V AC Gold Contacts 0.4VA max. @ 28V AC/DC max. CAP COLORS A B C Black White Red TERMINALS EP P Epoxy Sealed PC/Turret No Epoxy PC/Turret IMPORTANT: Switches are supplied without UL & C-UL markings unless specified. Specific models & ratings noted on General Specifications page. CAPS F H .201” (5.1mm) Dia. .295” (7.5mm) Dia. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE FB15ANEP2-FA .201” (5.1mm) Diameter Black Cap Silver Contacts & 500-Milliamp Rating SPST OFF-(ON) Circuit Epoxy Sealed PC/Turret Terminals POLE & CIRCUIT Plunger Position ( ) = Momentary Normal Pole SP Model FB15AN OFF (ON) OPEN 1-2 Down Connected Terminals Normal Down Throw & Switch Schematics Note: Terminal numbers are not actually on the switch. SPST 1 2 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 .5 Amp Momentary Pushbuttons TERMINALS EP Epoxy Sealed PC/Turret Terminals Series FB P No Epoxy PC/Turret Terminals CONTACT MATERIALS & RATINGS 2 4 Silver Contacts Gold Contacts Power Level Logic Level 500mA @ 125V AC 0.4VA maximum @ 28V AC/DC maximum Complete explanation of operating range in Supplement section. TYPICAL SWITCH DIMENSIONS PC/Turret (5.1) Dia .201 (4.0) .157 M5 P0.5 (1.2) .047 (5.0) Dia .197 (2.8) Dia .110 (0.15) Typ .006 (5.0) .197 (5.9) (4.0) .232 .157 (11.8) .465 (2.7) .106 (2.54) .100 (7.0) Dia .276 FB15ANEP2-FA Plunger is white polyacetal. SLIP-ON CAPS & COLORS F AT475 .201” (5.1mm) Diameter (5.1) Dia .201 (5.9) .232 (4.0) .157 H AT496 .295” (7.5mm) Diameter (7.5) Dia .295 (5.9) .232 (4.0) .157 Material: Polyamide Finish: Glossy Material: Polyamide Finish: Glossy Colors Available: A Black B White C Red STANDARD HARDWARE & PANEL CUTOUT M5 P0.5 AT536 Hex Nut Material: Brass with nickel plating (8.0) .315 (7.0) .276 Panel Thickness: .110” (2.8mm) maximum (5.3) Dia .209 (1.2) .047 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07