G12JPCF

Series G Toggles Fully Illuminated Ultra-Miniature Toggles A Rockers General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Programmable Illuminated PB Pushbuttons Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Keylocks Nominal Operating Force: Angle of Throw: 80 milliohms maximum 500 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum 100,000 operations minimum 10,000 operations minimum @ 0.1A @ 28V AC/DC 1.30N 28° Materials & Finishes Rotaries Actuator: Case: Sealing Rings: Movable Contacts: Stationary Contacts: Base: Power Terminals: Lamp Terminals: Polyamide Glass fiber reinforced polyamide Nitrile butadiene rubber Phosphor bronze with gold plating Phosphor bronze with gold plating Glass fiber reinforced polyamide Phosphor bronze with gold plating Phosphor bronze with gold plating Tactiles Slides Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: –25°C through +55°C (–13°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 500Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Tilt Touch PCB Processing Soldering: Cleaning: Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Automated cleaning. See Cleaning specifications in Supplement section. Indicators Standards & Certifications Supplement Accessories The G Series toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. A38 www.nkk.com Fully Illuminated Ultra-Miniature Toggles Series G A Toggles Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Distinctive Characteristics Fully illuminated toggle for highly visible status indication with LED in red, green, or amber for single color and red/green for bicolor. Ultra-miniature size allows high density mounting, and extremely light weight makes these switches ideal for handheld equipment. Totally sealed body construction prevents contact contamination and allows time- and money-saving automated soldering and cleaning. Molded-in, epoxy sealed terminals lock out flux, solvents, and other contaminants. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smooth, positive detent actuation, increased contact stability, and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Round terminals facilitate easier throughhole mounting on PC boards. Actual Size www.nkk.com A39 Series G Toggles Fully Illuminated Ultra-Miniature Toggles TYPICAL SWITCH ORDERING EXAMPLE A Rockers G Pole 1 SPDT 2 1 Circuits ON NONE ON 2 Actuator J Clear J P H V H PC Terminals Straight Right Angle Vertical C D F C LEDS Single Color Red Amber Green Bicolor CF Red/Green ON-NONE-ON & ON-OFF-ON Pushbuttons Programmable Illuminated PB Combines with single color or bicolor LEDs 3 ON OFF ON Combines with bicolor LED only SPDT ON-NONE-ON Circuit Clear Toggle, Red LED ON-NONE-ON only DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Keylocks G12JHC Right Angle PC Terminals P OLES & CIRCUITS Toggle Position Up Pole Throw Model G12 G13 Slot Rotaries Connected Terminals Up Slot Schematics Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external power source. 2 (COM) 3 1 (4) Red (5) (6) (5) (6) Green Center Down Center Down Slides SPDT ON ON NONE OFF ON ON 2-3 2-3 NONE OPEN 2-1 2-1 Single Color Bicolor Tactiles ACTUATOR J 28° Clear Toggle (3.8) .150 (1.7) Dia .067 (4.0) Dia .157 Tilt Touch LED COLORS & SPECIFICATIONS Single Color LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement; see Supplement Index. Bicolor Indicators C Colors Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage I FM IF VF VRM Red 25mA 20mA 2.0V 4V D Amber 25mA 20mA 2.1V 4V F Green 25mA 20mA 2.1V 4V 0.33mA/°C –25° ~ +55°C CF Red/Green 25mA/25mA 20mA/20mA 2.0V/2.1V 4V/4V Accessories Supplement Current Reduction Rate Above 25°C ∆I F Ambient Temperature Range A40 www.nkk.com Fully Illuminated Ultra-Miniature Toggles PC TERMINALS P Straight (2.54) Typ .100 (0.4) Dia Typ .016 (2.54) Typ .100 (2.6) .102 Series G A V Vertical (2.54) Typ .100 (0.4) Dia Typ .016 (7.0) .276 (4.5) .177 (7.0) .276 TYPICAL SWITCH DIMENSIONS Straight PC (1.7) Dia .067 (4.0) Dia .157 (0.4) Dia Typ .016 1 2 3 4 5 6 (2.54) .100 (7.0) .276 (0.6) Dia Typ .024 (2.54) .100 4 5 6 1 2 3 28° (2.54) Typ .100 Slot (4.5) .177 (3.8) .150 (1.6) .063 (7.0) .276 (2.54) Typ .100 (2.6) .102 5 & 6 are LED terminals; 4 is a support pin on single color models & an LED terminal on bicolor models. G12JPC Right Angle PC 28° Slot (1.7) Dia .067 (4.0) Dia .157 3 2 1 (0.4) .016 (4.9) .193 4 5 6 (2.54) .100 (5.08) .200 (2.6) .102 (0.4) Dia Typ .016 (5.08) .200 (7.8) .307 (3.8) .150 (5.08) .200 (1.6) .063 (10.22) .402 (0.5) .020 (2.54) .100 6 5 4 (0.6) Dia Typ .024 (0.4) Dia Typ .016 (2.54) Typ .100 (7.0) .276 Vertical PC (1.7) Dia .067 (4.0) Dia .157 1 2 3 4 5 6 (0.4) .016 (7.4) .292 4 5 6 1 2 3 28° (2.6) .102 (1.0) .039 (5.08) .200 (12.76) .502 (0.5) Typ .020 (2.54) Typ .100 (2.54) Typ .100 (5.08) .200 (0.4) Dia Typ .016 (2.54) .100 (5.3) .209 (1.6) .063 (3.8) .150 (0.4) Dia Typ .016 (2.54) .100 (4.5) .177 5 & 6 are LED terminals; 4 is a support pin on single color models & an LED terminal on bicolor models. www.nkk.com G12JVCF A41 Supplement Accessories Slot (0.6) Dia Typ .024 Indicators (2.54) .100 Touch 5 & 6 are LED terminals; 4 is a support pin on single color models & an LED terminal on bicolor models. G12JHD Tilt Tactiles (2.54) Typ .100 1 2 3 Slides Rotaries Keylocks Programmable Illuminated PB (4.5) .177 (2.54) Typ .100 (7.0) .276 (4.5) .177 Pushbuttons (0.5) Typ .020 (0.4) Dia Typ .016 (2.54) Typ .100 (2.54) Typ .100 (0.5) Typ .020 Rockers H Right Angle Toggles