KP0215ANBKG036CF-1FJB 数据手册
Series KP
Toggles
Miniature Audio/Video Pushbuttons
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Low Level: 100mA maximum @ 12V DC
Pushbuttons
Other Ratings
Programmable Illuminated PB
D
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life:
Electrical Life: Nominal Operating Force: Travel:
Keylocks
200 milliohms maximum 100 megohms minimum @ 250V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum 5,000,000 operations minimum; 1,000,000 operations minimum for custom Rectangular Switch/Cap Assembly (at center of cap) 5,000,000 operations minimum KP01: 1.9N maximum for Tactile & Nontactile models (at center of cap) KP02: 1.6N maximum for Tactile, Nontactile & Tactile/Audible models (at center of cap) KP01: Pretravel .122” (3.1mm); Overtravel .055” (1.4mm); Total Travel .177” (4.5mm) KP02: Pretravel .091” (2.3mm); Overtravel .047” (1.2mm); Total Travel .138” (3.5mm)
Materials & Finishes
Plunger/Upper Housing: Lower Housing: Movable Contact: Stationary Contacts: Switch Terminals:
Polyacetal Glass fiber reinforced PBT (UL94V-0) Stainless steel with gold plating Gold over copper alloy Brass with tin plating
Slides
Rotaries
Environmental Data
Tactiles
Operating Temperature Range: Humidity: Vibration: Shock:
–25°C through +50°C (–13°F through +122°F) 90-95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 51G (500m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Installation
Cap Installation Force :
50.0N maximum downward force on actuator
Touch
PCB Processing
Soldering: Cleaning:
Indicators
Wave Soldering. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards:
Accessories
UL94V-0 lower housing The KP Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Supplement
D36
www.nkk.com
Miniature Audio/Video Pushbuttons
Series KP
Toggles
Available with super bright red/green bicolor LED and RGB LEDs. The RGB LED full color spectrum in a switch package provides unlimited color combinations. Specially designed snap-in standoff for simple and secure PC board mounting and alignment. Unique actuation guide gives positive indication of circuit transfer as well as smooth and silent operation. (Patent pending). Choices of tactile, nontactile or tactile/audible actuation. Compact design with height of .906” (23.0mm) from PC board to top of cap. (Same height as programmable SmartSwitch™.) Flat, sculptured or home key square caps in three common sizes for design flexibility in audio/video applications. Twin contacts with gold plating assure high reliability and long life of 5,000,000 operations minimum.
Actual Size
D
www.nkk.com
D37
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Distinct, long total travel of .177” (4.5mm) for KP01 or shorter stroke of .138 (3.5mm) for KP02.
Pushbuttons
KP series offers a complete switch solution for all broadcast panel needs, including home keys and the custom rectangular switch/cap assembly.
Rockers
Distinctive Characteristics
Series KP
Toggles
Miniature Audio/Video Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
Pushbuttons
Rockers
KP 01 15A N B K G03 6CF
Housing
K Black only 6CF RGB
2 S JB
Cap Colors
JB Clear Lens & White Diffuser
LEDs
Super Bright Red/Green Bicolor Red/Green/Blue (Custom) * See Note
Programmable Illuminated PB
D
Pole & Circuit
15A SPST OFF (ON) ( ) = Momentary Normally Open Contacts A B
Plungers
9.2mm Plunger for 12.0mm Cap 11.6mm Plunger for 15.0mm & 17.4mm Caps
Cap Types
F Flat Sculptured Home Key
Contacts & Terminals
G03 Gold Contacts and Straight PC Terminals; 100mA @ 12V DC
S T
Rotaries
Keylocks
Travel & Force
01 02 Stroke: 4.5mm (.177”) Actuation Force: 1.9N Stroke: 3.5mm (.138”) Actuation Force: 1.6N
Actuation
01 C N Tactile Nontactile 02 1 2 3
Cap Sizes
12.0mm Square 15.0mm Square 17.4mm Square ** See Note Notes * Custom RGB LED Page D42 ** Custom Rectangular Cap Page D43
Slides
Tactiles
C N S
Tactile Nontactile Tactile/Audible
Tilt
Touch
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
KP0115ANBKG036CF-2SJB
Indicators
11.6mm Plunger and 15.0mm Sculptured Cap Clear Lens and White Diffuser SPST OFF-Momentary ON Circuit Normally Open Contacts
Super Bright Red/Green Bicolor LED Nontactile Actuation Black Housing Gold Contacts with 100mA Rating Straight PC Terminals
Supplement
Accessories
D38
www.nkk.com
Miniature Audio/Video Pushbuttons
P OLE & CIRCUIT
Plunger Position ( ) = Momentary Normal Down Connected Terminals Normal Down
Series KP
Throw & Switch Schematic Note: Switch terminals “1” & “1a” are actually marked on the switch.
1 (COM)
Pole
Model
SP
KP0115A KP0215A
OFF
(ON)
Normally Open
1-1a
SPST
1a
ACTUATION C
Tactile KP01 or KP02
HOUSING S
Tactile/Audible KP02 only
D
N
Nontactile KP01 or KP02
K
Black only
G03
Gold Contacts
Straight PC Terminals
100mA @ 12V DC
Rotaries
SUPER BRIGHT BICOLOR LED SPECIFICATIONS
The electrical specifications shown are determined at a basic temperature of 25°C.
Red
Colors IV IV I FM IF VF
PD
Red 450 700 30 (25 for amber) 15 2.1 63 5 630 ~ 640 0.40 –25 ~ +50
Green 820 1100 25 (22 for amber) 15 3.2 80 5 520 ~ 535 0.36
Unit mcd mcd mA
Minimum Luminous Intensity LEDs are an integral part of the switch and are not available separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Standard Luminous Intensity Forward Peak Current Continuous Forward Current Forward Voltage Power Peak Dissipation Reverse Peak Voltage Wavelength at Peak Emission Current Reduction Rate Above 25°C Ambient Temperature Range
V mW V nm mA/°C °C
VRM λ ∆I F
Amber can be achieved by simultaneous illumination of Red & Green.
www.nkk.com
D39
Supplement
Accessories
Indicators
Touch
mA
Tilt
Tactiles
ELECTROSTATIC SENSITIVE DEVICES
ATTENTION
(–) L2 (+) COM Green (–) L1
6 CF
Slides
Keylocks
CONTACTS, TERMINALS, & RATING
Programmable Illuminated PB
Pushbuttons
Rockers
Toggles
Series KP
Toggles
Miniature Audio/Video Pushbuttons
PLUNGERS
Rockers
A
9.2mm Plunger for 12.0mm Cap 9.2mm Plunger is designed with a narrower neck to hold the 12.0mm Cap.
(9.2) .362 (6.4) .252
B
11.6mm Plunger for 15.0mm & 17.4mm Caps 11.6mm Plunger is designed with a wider neck to hold both the 15.0mm and 17.4mm Caps.
(11.6) .457 (6.4) .252
Pushbuttons
CAP TYPES & COLORS
Programmable Illuminated PB
D
1
12.0mm Square
Used on A Plunger
F
AT3083 Flat Cap
(6.5) .256
S
AT3078 Sculptured Cap
(6.5) .256
T
AT3086 Home Key Cap
(6.5) .256
Keylocks
(2.6) Dia .102
(12.0) Sq .472
(12.0) Sq .472
(12.0) Sq .472
2
15.0mm Square
Used on B Plunger
Rotaries
F
AT3084 Flat Cap
S
(7.0) .276
AT3079 Sculptured Cap
T
(7.0) .276
AT3087 Home Key Cap
Slides
(7.0) .276 (2.6) Dia .102
(15.0) Sq .591
(15.0) Sq .591
(15.0) Sq .591
Tactiles
3
17.4mm Square
Used on B Plunger
Tilt
F
AT3085 Flat Cap
S
AT3080 Sculptured Cap
T
AT3088 Home Key Cap
Touch
(7.0) .276
(7.0) .276 (2.6) Dia .102
(7.0) .276
(17.4) Sq .685
(17.4) Sq .685
(17.4) Sq .685
Indicators
JB
Lens & Diffuser Colors Available: Clear/White
Clear Lens White Diffuser
Accessories
Materials & Finishes: Lens - Polycarbonate with glossy finish; Diffuser - Polycarbonate with textured finish Optional Protective Guard AT4170 available; contact factory.
Supplement
D40
www.nkk.com
Miniature Audio/Video Pushbuttons
TYPICAL SWITCH DIMENSIONS
Series KP
12.0mm Square Cap
Rockers
(1.3) Dia Typ .051 (0.9) Dia Typ .035 (0.6) Dia Typ .024
– (5.08) + 0.5 .200
(12.0) Sq .472
(1.1) .043 (6.5) (5.0) (11.5) .256 .197 .453 (23.0) .906
(6.0) .236
(12.7) .500 (15.0) Sq .591
(2.54) Typ .100 (12.7) .500
D
KP0115ACAKG036CF-1SJB
(0.3) .012 (4.5) .177 (12.7) .500 (0.25) .010
(0.37) Typ .015
(0.6) Typ .024
(1.3) Dia Typ .051 (0.9) Dia Typ .035 (0.6) Dia Typ .024
1 L1 C
1a L2
L2
COM
L1
(4.5) .177 (12.7) .500
KP0115ANBKG036CF-2SJB
Tilt
17.4mm Square Cap
Touch
L2
(6.4) .252
(3.6) .142
(0.3) .012 (4.5) .177 (12.7) .500 (0.25) .010
(0.37) Typ .015
(7.62) .300
(0.6) Typ .024
(7.62) .300 (1.3) Dia Typ .051 (0.9) Dia Typ .035 (0.6) Dia Typ .024
1 L1 C 1a
L2
COM
L1
(4.5) .177 (12.7) .500
(17.4) Sq .685
(6.0) .236
(12.7) .500 (15.0) Sq .591
(12.7) .500
KP0115ANBKG036CF-3SJB www.nkk.com D41
Supplement
Accessories
(1.1) .043 (11.5) (7.0) (4.5) .453 .276 .177 (23.0) .906
– (5.08) + 0.5 .200
(2.54) Typ .100
Indicators
Tactiles
1
(15.0) Sq .591
(1.1) .043 (7.0) (4.5) (11.5) .276 .177 .453 (23.0) .906
– (5.08) + 0.5 .200
(6.0) .236
(12.7) .500 (15.0) Sq .591
(2.54) Typ .100 (12.7) .500
Slides
Rotaries
(6.4) .252
(3.6) .142
(7.62) .300
(7.62) .300
Keylocks
15.0mm Square Cap
Programmable Illuminated PB
(4.5) .177 (12.7) .500 (0.25) .010
1 L1 C
1a L2
L2
COM
L1
(4.5) .177 (12.7) .500
Pushbuttons
(6.4) .252
(3.6) .142
(0.3) .012
(0.37) Typ .015
(7.62) .300
(0.6) Typ .024
(7.62) .300
Toggles
1a 1a 1a
1 1
Series KP
Toggles
Miniature Audio/Video Pushbuttons
CUSTOM RGB LED SPECIFICATIONS
Rockers
Programmable Illuminated PB
D
The electrical specifications shown are determined at a basic temperature of 25°C. LEDs are an integral part of the switch and are not available separately. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement Section. Note: For applications that require white illumination, contact factory.
Red Green Common Anode (+) Blue
ELECTROSTATIC SENSITIVE DEVICES
ATTENTION
RGB
Red 30 20 2.0 40 5 625 0.50 Green 30 15 3.3 80 5 525 0.50 –25 ~ +50 Blue 30 15 3.4 80 5 470 0.50 Unit mA mA V mW V nm mA/°C °C
Pushbuttons
Color
I FM IF VF PD VRM λd ∆ IF
Forward Peak Current Continuous Forward Current Forward Voltage Power Peak Dissipation Reverse Peak Voltage Dominant Wavelength Current Reduction Rate Above 25°C Ambient Temperature Range
TYPICAL SWITCH DIMENSIONS
12.0mm Square Cap with RGB LED
1a Common Anode (+) B(-) 1
Keylocks
Terminal Detail
R(-) G(-) (1.3) Dia Typ .051
1
Rotaries
(6.4) .252
(3.6) .142
(0.3) .012
(7.62) .300
(0.6) Typ .024 (4.5) .177
(7.62) .300
1a B(-) (+)
Slides
(3.81) .150 (1.1) .043 (11.5) (6.5) (5.0) .256 .197 .453 (23.0) .906
(12.7) .500
See Terminal Detail (1.52) Typ .060 (12.7) .500 (15.0) Sq .591
(0.9) Dia Typ .035 (0.7) Dia Typ .028 (1.52) Typ .060
R(-) G(-)
(4.5) .177 (12.7) .500 (3.81) .150
1a
1
(0.2) Sq Typ .008 (4.0) .157
(12.7) .500
Tactiles
(12.0) Sq .472
KP0115ACAKG03RGB-1SJB
15.0mm & 17.4mm Square Caps with RGB LED
Tilt
Common Anode (+) B(-) 1a 1
15.0mm Cap
Touch
(15.0) Sq .591
Terminal Detail
R(-) G(-)
Indicators
KP0115ANBKG03RGB-2SJB
(6.4) .252
(3.6) .142
(0.3) .012
(7.62) .300
(0.6) Typ .024 (1.3) Dia Typ .051
1
(7.62) .300
1a B(-) (+)
Accessories
(3.81) .150 (1.1) .043 (11.5) (7.0) (4.5) .276 .177 .453 (23.0) .906
(12.7) .500
(0.9) Dia Typ See Terminal .035 (0.7) Dia Typ Detail .028 (1.52) Typ .060 (12.7) .500 (15.0) Sq .591 (1.52) Typ .060
(4.5) .177
1a
1
R(-) G(-)
(4.5) .177 (12.7) .500 (3.81) .150
(0.2) Sq Typ .008 (4.0) .157
Supplement
(12.7) .500
(17.4) Sq .685
KP0115ANBKG03RGB-3SJB D42
17.4mm Cap
www.nkk.com
Miniature Audio/Video Pushbuttons
CUSTOM RECTANGULAR CAP ASSEMBLY CAP ASSEMBLY DIMENSIONS
(3.6) .142 (4.5) .177
Series KP
Toggles
Switch/Rectangular Cap Assembly
1
(34.8) 1.370
(12.7) .500 (2.54) .100
(7.62) .300 (0.6) .024
L+ L– 1a
D
(7.0) .276 (17.4) .685 (23.0) .906 (6.0) .236 (0.3) .012 (12.7) .500 (15.0) Sq .591
See below for complete assembly of switch, LEDs and LED holders.
KP0115ACBKG03CJB for Tactile KP0115ANBKG03CJB for Nontactile
The electrical specifications shown are determined at a basic temperature of 25°C. Center LED is an integral part of the switch. LEDs are not sold separately. LED circuits are isolated and require an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement Section.
(+)
(-)
Color I FM IF VF VRM λd ∆I F
Red 30 20 2.0 4 623 0.32 –25 ~ +50
Unit mA mA V V mA/°C °C nm
Continuous Forward Current Forward Voltage Reverse Peak Voltage Dominant Wavelength Current Reduction Rate Above 25°C Ambient Temperature Range Contact factory for other LED colors.
ASSEMBLY & INSTALLATION INSTRUCTIONS
(3.1) Dia .122 Cathode (2.54) .100 (0.9) Dia Typ .035 (1.3) Dia Typ .051 (12.7) .500 (5.9) .232 (6.7) .264 (10.4) .409 LED Holder (4.5) .177
LED
Footprint
(2.54) .100
L+ L–
1
LED Holder
(12.7) .500
LED
2 3
Switch
PCB
www.nkk.com
D43
Supplement
One LED (in center of switch bottom) is an integral part of the switch; the other 2 LEDs and 2 LED Holders are packaged separately.
Solder LEDs and LED Holders into PCB. Solder switch into PCB making sure that the two outer LEDs and LED Holders clear the bottom side opening of the cap.
Accessories
Switch/Rectangular Cap assembly has 3 LEDs to achieve bright and even illumination.
1
Install LED into LED Holder (quantity 2).
Indicators
(4.8) .189
(0.8) Dia Typ .031
(2.54) .100
Touch
1a
(7.62) (12.7) (22.86) .300 .500 .900
Tilt
Tactiles
Slides
Rotaries
Forward Peak Current
Keylocks
LED SPECIFICATIONS
Programmable Illuminated PB
(0.45) Sq Typ .018
Pushbuttons
Rockers
Series KP
Toggles
Miniature Audio/Video Pushbuttons
ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS
Rockers
ELECTROSTATIC SENSITIVE DEVICES
ATTENTION
Cap Orientation
Notch Tab Step Plunger Notches
Programmable Illuminated PB
Pushbuttons
As shown in the accompanying illustration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch.
D
Removal of Cap Assembly & Separation of Lens & Diffuser
Holding the switch tightly, pull the cap off the switch. Once the cap assembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens with fingernail or flat tip screwdriver inserted at the step on the diffuser.
Keylocks
Installation or Replacement of Cap
Rotaries
Cap Assembly
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Slides
After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together.
Plunger Switch
D44
www.nkk.com
Miniature Audio/Video Pushbuttons
LEGENDS
Series KP
Toggles
NKK Switches can provide custom legends for caps. Contact factory for more information.
Rockers
Suggested Printable Areas for KP Lens
Pushbuttons
Lens
Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens. Laser Print on film insert. Epoxy based ink is recommended.
Film Insert Diffuser
Printing on Diffuser is not advisable.
D
Shaded areas are suggested printable areas for Lens.
Custom Rectangular Cap Lens
Flat Cap Lens
Sculptured Cap Lens
(28.75) 1.132
(9.8) Sq .386 (12.0) Sq .472
(12.8) Sq .504 (15.0) Sq .591
(13.4) Sq .528 (17.4) Sq .685
(8.97) Dia .353 (10.5) Dia .413
Suggested Printable Areas for KP Film Insert
(0.5) R .020 (2.125) Typ .084 (28.75) 1.132 (0.5) R .020 (33.0) 1.299
(0.5) R .020
(0.5) R .020
(0.5) R .020
(0.5) R .020
(0.5) R .020
Film Insert Material and Thickness: Clear Polyester; 4 mil (100µ) maximum thickness
www.nkk.com
D45
Supplement
Accessories
(8.28) Sq .326 (9.8) Sq .386
(0.76) Typ .030
(11.28) Sq .444 (12.8) Sq .504
(0.76) Typ .030
(11.88) Dia .468 (13.4) Sq .528
(0.76) Typ .030
(8.28)Dia .326 (9.8) Sq .386
(0.76) Typ .030
(11.28) Dia .444 (12.8) Sq .504
(0.76) Typ .030
(11.88) Dia .468 (13.4) Sq .528
(0.76) Typ .030
(13.77) .542 (15.6) .614
(0.91) Typ .036
Indicators
Touch
Flat Cap Film Inserts
Sculptured or Home Key Cap Film Inserts
Tilt
Shaded areas are suggested printable areas for Film Insert.
Custom Rectangular Film Insert
Tactiles
Slides
(0.76) Typ .030
(11.48) Dia .452 (13.0) Dia .512
(0.76) Typ .030
(13.77) Dia .542 (15.3) Dia .602
(0.76) Typ .030
(13.77) .542 (15.3) .602
(0.76) Typ .030
Rotaries
(30.28) 1.192
Keylocks
Programmable Illuminated PB
OP ST
KP0215ANBKG036CF-1FJB 价格&库存
很抱歉,暂时无法提供与“KP0215ANBKG036CF-1FJB”相匹配的价格&库存,您可以联系我们找货
免费人工找货