ADC08061

ADC08061/ADC08062 500 ns A/D Converter with S/H Function and Input Multiplexer OBSOLETE ADC08061/ADC08062 500 ns A/D Converter with S/H Function and Input Multiplexer General Description NOTE: These products are obsolete. This data sheet is provided for reference only. Using a patented multi-step A/D conversion technique, the 8bit ADC08061 and ADC08062 CMOS ADCs offer 500 ns (typ) conversion time, internal sample-and-hold (S/H), and dissipate only 125 mW of power. The ADC08062 has a twochannel multiplexer. The ADC08061/2 performs 8-bit conversions using a multistep flash approach. Input track-and-hold circuitry eliminates the need for an external sample-and-hold. The ADC08061/2 performs accurate conversions of full-scale input signals that have a frequency range of DC to 300 kHz (full-power bandwidth) without need of an external S/H. The digital interface has been designed to ease connection to microprocessors and allows the parts to be I/O or memory mapped. July 15, 2009 Key Specifications ■ ■ ■ ■ ■ ■ Resolution Conversion Time Full Power Bandwidth Throughput rate Power Consumption Total Unadjusted Error 8 bits 560 ns max (WR-RD Mode) 300 kHz 1.5 MHz 100 mW max ±½ LSB and ±1 LSB Features ■ ■ ■ ■ ■ 1 or 2 input channels No external clock required Analog input voltage range from GND to V+ Overflow output for cascading (ADC08061) ADC08061 pin-compatible with the ADC0820 Applications ■ ■ ■ ■ Mobile telecommunications Hard disk drives Instrumentation High-speed data acquisition systems Block Diagram 1108601 * ADC08061 ** ADC08062 Ordering Information Industrial (−40°C ≤ TA ≤ 85°C) ADC08061BIN, ADC08062BIN ADC08061CIWM, ADC08062CIWM Package N20A M20B © 2009 National Semiconductor Corporation 11086 Print Date/Time: 2009/07/15 15:48:35 www.national.com 11086 Version 6 Revision 2 ADC08061/ADC08062 Connection Diagrams 1108614 1108615 Dual-In-Line and Wide-Body Small-Outline Packages N20A or M20B Dual-In-Line and Wide-Body Small-Outline Packages N20A or M20B output latch. INT is reset by the rising edge of RD. This is the power supply ground pin. The ground pin should be connected to a “clean” ground reference point. These are the reference voltage inputs. They may be placed at any voltage between GND − 50 mV and V+ + 50 mV, but VREF+ must be greater than VREF−. Ideally, an input voltage equal to VREF− produces an output code of 0, and an input voltage greater than VREF+ − 1.5 LSB produces an output code of 255. For the ADC08062, an input voltage on any unselected input that exceeds V+ by more than 100 mV or is below GND by more than 100 mV will create errors in a selected channel that is operating within proper operating conditions. This is the active low Chip Select input. A logic low signal applied to this input pin enables the RD and WR inputs. Internally, the CS signal is ORed with RD and WR signals. Overflow Output. If the analog input is higher than VREF+ − ½ LSB, OFL will be low at the end of conversion. It can be used when cascading two ADC08061s to achieve higher resolution (9 bits). This output is always active and does not go into TRI-STATE as DB0–DB7 do. When OFL is set, all data outputs remain high when the ADC08061's output data is read. No connection. This logic input is used to select one of the ADC08062's input multiplexer channels. A channel is selected as shown in the table below. ADC08062 A0 0 1 Channel VIN1 VIN2 Pin Descriptions VIN,VIN1–8 These are analog inputs. The input range is GND–50 mV ≤ VINPUT ≤ V+ + 50 mV. The ADC08061 has a single input (VIN) and the ADC08062 has a two-channel multiplexer (VIN1–2). TRI-STATE data outputs—bit 0 (LSB) through bit 7 (MSB). WR-RD Mode (Logic high applied to MODE pin) WR: With CS low, the conversion is started on the falling edge of WR. The digital result will be strobed into the output latch at the end of conversion (see Figures 2, 3, 4). RD Mode (Logic low applied to MODE pin) RDY: This is an open drain output (no internal pull-up device). RDY will go low after the falling edge of CS and return high at the end of conversion. Mode: Mode (RD or WR-RD) selection input— This pin is pulled to a logic low through an internal 50 µA current sink when left unconnected. RD Mode is selected if the MODE pin is left unconnected or externally forced low. A complete conversion is accomplished by pulling RD low until output data appears. WR-RD Mode is selected when a high is applied to the MODE pin. A conversion starts with the WR signal's rising edge and then using RD to access the data. WR-RD Mode (logic high on the MODE pin) This is the active low Read input. With a logic low applied to the CS pin, the TRI-STATE data outputs (DB0–DB7) will be activated when RD goes low (Figures 2, 3, 4). RD Mode (logic low on the MODE pin) With CS low, a conversion starts on the falling edge of RD. Output data appears on DB0–DB7 at the end of conversion (see Figures 1, 5). This is an active low output that indicates that a conversion is complete and the data is in the 2 11086 Version 6 Revision 2 GND VREF−,VREF+ DB0–DB7 WR /RDY   : CS MODE OFL NC A0 RD INT V+ Positive power supply voltage input. Nominal operating supply voltage is +5V. The supply pin should be bypassed with a 10 µF bead tantalum in parallel with a 0.1 ceramic capacitor. Lead length should be as short as possible. www.national.com Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 Absolute Maximum Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V+) Logic Control Inputs Voltage at Other Inputs and Outputs Input Current at Any Pin (Note 3) Package Input Current (Note 3) Power Dissipation (Note 4) All Packages Storage Temperature Lead Temperature (Note 5) J Package (Soldering, 10 sec.) N Package (Soldering, 10 sec.) WM Package (Vapor Phase, 60 sec.) WM Package (Infrared, 15 sec.) ESD Susceptibility (Note 6) 6V −0.3V to V+ + 0.3V −0.3V to V+ + 0.3V 5 mA 20 mA 875 mW −65°C to +150°C +300°C +260°C +215°C +220°C 2 kV Operating Ratings Temperature Range Supply Voltage, (V+) Pos. Reference Voltage, VREF+ Neg. Reference Voltage, VREF− Input Voltage Range (Notes 1, 2) TMIN ≤ TA ≤ TMAX = −40°C ≤ TA ≤ 85°C +4.5V to +5.5V (VREF− + 1V) to V+ GND to (VREF+ − 1V) VREF− to VREF+ Converter Characteristics The following specifications apply for RD Mode, V+ = 5V, VREF+ = 5V, and VREF− = GND unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C. Symbol INL TUE Parameter Integral Non Linearity Total Unadjusted Error Missing Codes Reference Input Resistance VREF+ VREF− VIN Positive Reference Input Voltage Negative Reference Input Voltage Analog Input Voltage (Note 10) On Channel Input = 5V, Off Channel Input = 0V (Note 11) On Channel Input = 0V, Off Channel Input = 5V (Note 11) V+ = 5V ±5%, VREF = 4.75V All Codes Tested −0.4 −0.4 ±1/16 7.8 300 0.5 50 50 700 700 Conditions ADC08061/2BIN ADC08061/2CIWM ADC08061/2BIN ADC08061/2CIWM Typical (Note 7) Limits (Note 8) ±½ ±1 ±½ ±1 0 500 1250 VREF− V+ GND VREF+ GND − 0.1 V+ + 0.1 −20 −20 ±½ Units (Limit) LSB (max) LSB (max) LSB (max) LSB (max) Bits (max) Ω(min) Ω (max) V (min) V (max) V (min) V (max) V (min) V (max) µA (max) µA (max) LSB (max) Bits kHz % dB dB On Channel Input Current PSS Power Supply Sensitivity Effective Bits Full-Power Bandwidth THD S/N IMD Total Harmonic Distortion Signal-to-Noise Ratio Intermodulation Distortion 3 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 AC Electrical Characteristics The following specifications apply for V+ = 5V, tr = tf = 10 ns, VREF+ = 5V, VREF− = 0V unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C. Symbol tWR tRD tRDW tCONV tCRD tACCO Parameter Write Time Condition Mode Pin to V+; (Figures 2, 3, 4) Typical (Note 7) 100 350 200 400 500 655 640 Limits (Note 8) 100 350 250 400 560 900 900 Units (Limit) ns (min) ns (min) ns (min) ns (max) ns (max) ns (max) ns (max) Read Time (Time from Falling Edge of Mode Pin to V+; (Figure 2) WR to Falling Edge of RD ) RD Width Mode Pin to GND; (Figure 5) WR -RD Mode Conversion Time (tWR Mode Pin to V+; (Figure 2) + tRD + tACC1) RD Mode Conversion Time Mode Pin to GND; (Figure 1) Access Time (Delay from Falling Edge CL ≤ 100 pF Mode Pin to GND; of RD to Output Valid) (Figure 1) Mode Pin to V+, tRD ≤ tINTL Access Time (Delay from Falling Edge (Figure 2) CL = 10 pF of RD to Output Valid) CL ≤ 100 pF tRD > tINTL; (Figures 3, 4) CL ≤ 10 pF CL = 100 pF RL = 3 kΩ, CL = 10 pF RL = 3 kΩ, CL = 10 pF (Figures 3, 4) Mode Pin = V+, CL = 50 pF CL = 50 pF; (Figures 1, 2, 3, 4)2b, and 4 ) CL = 50 pF; (Figure 4) Mode Pin = 0V, CL = 50 pF, RL = 3 kΩ (Figure 1) RL = 3 kΩ, CL = 100 pF; (Figure 4) Mode Pin = V+, tRD ≤ tINTL; (Figure 3) tACC1 45 50 110 ns (max) ns tACC2 Access Time (Delay from Falling Edge of RD to Output Valid) TRI-STATE Control (Delay from Rising Edge of RD to HI-Z State) TRI-STATE Control (Delay from Rising Edge of RD to HI-Z State) Delay from Rising Edge of WR to Falling Edge of INT Delay from Rising Edge of RD to Rising Edge of INT Delay from Rising Edge of WR to Rising Edge of INT Delay from CS to RDY Delay from INT to Output Valid Delay from RD to INT 25 30 30 30 520 50 45 25 0 60 50 10 0 0 0 25 5 5 55 ns (max) t0H t1H tINTL tINTH tINTH tRDY tID tRI tN tAH tAS tCSS tCSH CVIN COUT CIN 60 60 690 95 95 45 15 115 50 60 0 0 0 ns (max) ns (max) ns (max) ns (max) ns (max) ns (max) ns (max) ns (max) ns (min) ns (min) ns (max) ns (max) ns (min) pF pF pF Time between End of RD and Start of (Figures 1, 2, 3, 4, 5) New Conversion Channel Address Hold Time Channel Address Setup Time CS Setup Time CS Hold Time Analog Input Capacitance Logic Output Capacitance Logic Input Capacitance (Figures 1, 2, 3, 4, 5) (Figures 1, 2, 3, 4, 5) (Figures 1, 2, 3, 4, 5) (Figures 1, 2, 3, 4, 5) www.national.com 11086 Version 6 Revision 2 4 Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 DC Electrical Characteristics The following specifications apply for V+ = 5V unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C. Symbol Parameter V+ = 5.5V VIH Logic “1” Input Voltage Mode Pin ADC08062 CS, WR, RD, A0 Pins ADC08061 CS, WR, RD Pins V+ = 4.5V VIL Logic “0” Input Voltage Mode Pin ADC08062 CS, WR, RD, A0 Pins ADC08061 CS, WR, RD Pins VIH = 5V IIH Logic “1” Input Current CS, RD, A0 Pins WR Pin Mode Pin VIL = 0V IIL Logic “0” Input Current CS, RD, WR, A0 Pins Mode Pin V+ = 4.75V IOUT = −360 µA VOH Logic “1” Output Voltage DB0–DB7, OFL, INT IOUT = −10 µA DB0–DB7, OFL, INT VOL Logic “0” Output Voltage V+ = 4.75V, IOUT = 1.6 mA DB0–DB7, OFL, INT, RDY VOUT = 5.0V IO TRI-STATE Output Current DB0–DB7, RDY VOUT = 0V DB0–DB7, RDY ISOURCE ISINK IC Output Source Current Output Sink Current Supply Current VOUT = 0V DB0–DB7, OFL, INT VOUT = 5V DB0–DB7, OFL, INT, RDY CS = WR = RD = 0 0.1 −0.1 −26 24 11.5 2.4 4.5 0.4 3 −3 −6 7 20 V (min) V (min) V (max) µA (max) µA (max) mA (min) mA (min) mA (max) −0.005 −2 µA (max) 0.005 0.1 50 1 3 200 µA (max) µA (max) µA (max) 1.5 0.7 0.8 V (max) V (max) V (max) 3.5 2.2 2.0 V (min) V (min) V (min) Conditions Typical (Note 7) Limits (Note 8) Units (Limit) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating ratings. Operating Ratings indicate conditions for which the device is functional, but do not guarantee performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to the GND pin, unless otherwise specified. Note 3: When the input voltage (VIN) at any pin exceeds the power supply voltage (VIN < GND or VIN > V+), the absolute value of the current at that pin should be limited to 5 mA or less. The 20 mA package input current specification limits the number of pins that can exceed the power supply boundaries with a 5 mA current limit to four. Note 4: The power dissipation of this device under normal operation should never exceed 875 mW (Quiescent Power Dissipation + the loads on the digital outputs). Caution should be taken not to exceed absolute maximum power rating when the device is operating in a severe fault condition (e.g., when any input or output exceeds the power supply). The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX (maximum junction temperature), θJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJMAX − TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower. The table below details TJMAX and θJA for the various packages and versions of the ADC08061/2. Part Number ADC08061/2BIN ADC08061/2CIWM Note 6: Human body model, 100 pF discharged through a 1.5 kΩ resistor. TJMAX 105 105 θJA 51 85 Note 5: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. 5 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 Note 7: Typical figures are at 25°C and represent most likely parametric norm. Note 8: Limits are guaranteed to National's AOQL (Average Output Quality Level). Note 9: Total unadjusted error includes offset, full-scale, and linearity errors. Note 10: Two on-chip diodes are tied to each analog input and are reversed biased during normal operation. One is connected to V+ and the other is connected to GND. They will become forward biased and conduct when an analog input voltage is equal to or greater than one diode drop above V+ or below GND. Therefore, caution should be exercised when testing with V+ = 4.5V. Analog inputs with magnitudes equal to 5V can cause an input diode to conduct, especially at elevated temperatures. This can create conversion errors for analog signals near full-scale. The specification allows 50 mV forward bias on either diode; e.g., the output code will be correct as long as the analog input signal does not exceed the supply voltage by more than 50 mV. Exceeding this range on an unselected channel will corrupt the reading of a selected channel. An absolute analog input signal voltage range of 0V ≤ VIN ≤ 5V can be achieved by ensuring that the minimum supply voltage applied to V+ is 4.950V over temperature variations, initial tolerance, and loading. Note 11: Off-channel leakage current is measured after the on-channel selection. TRI-STATE Test Circuits and Waveforms t1H t0H, CL = 10 pF 1108602 1108605 t1H, CL = 10 pF tr = 10 ns 1108604 tr = 10 ns t0H 1108603 www.national.com 11086 Version 6 Revision 2 6 Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 Timing Diagrams 1108606 FIGURE 1. RD Mode (Mode Pin is Low) 1108607 FIGURE 2. WR-RD Mode (Mode Pin is High and tRD ≤ tINTL) 7 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 1108608 FIGURE 3. WR-RD Mode (Mode Pin is High and tRD > tINTL) 1108609 FIGURE 4. WR-RD Mode (Mode Pin is High) Reduced Interface System Connection (CS = RD = 0) www.national.com 11086 Version 6 Revision 2 8 Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 1108610 FIGURE 5. RD Mode (Pipeline Operation) (Mode Pin is Low and tRDW must be between 200 ns and 400 ns) 9 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 Typical Performance Characteristics tCRD vs. Temperature Linearity Error vs. Reference Voltage 1108625 1108626 Offset Error vs. Reference Voltage Supply Current vs. Temperature 1108627 1108628 Logic Threshold vs. Temperature Output Current vs. Temperature 1108629 1108630 www.national.com 11086 Version 6 Revision 2 10 Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 Application Information 1.0 FUNCTIONAL DESCRIPTION The ADC08061 and ADC08062 perform 8-bit analog-to-digital conversions using a multi-step flash technique. The first flash generates the five most significant bits (MSBs) and the second flash generates the three least significant bits (LSBs). Figure 6 shows the major functional blocks of the ADC08061/2's multi-step flash converter. It consists of an over-encoded 2½-bit Voltage Estimator, an internal DAC with two different voltage spans, a 3-bit half-flash converter and a comparator multiplexer. The resistor string near the center of the block diagram in Figure 6 forms the internal main DAC. Each of the eight resistors at the bottom of the string is equal to 1/256 of the total string resistance. These resistors form the LSB Ladder and have a voltage drop of 1/256 of the total reference voltage (VREF+ − VREF−) across them. The remaining resistors make up the MSB Ladder. They are made up of eight groups of four resistors connected in series. Each MSB Ladder section has ⅛ of the total reference voltage across it. Within a given MSB Ladder section, each of the MSB resistors has 8/256, or 1/32 of the total reference voltage across it. Tap points are found between all of the resistors in both the MSB and LSB Ladders. Through the Comparator Multiplexer these tap points can be connected, in groups of eight, to the eight comparators shown at the right of Figure 6. This function provides the necessary reference voltages to the comparators during each flash conversion. The six comparators, seven-resistor string (estimator DAC), and Estimator Decoder at the left of Figure 6 form the Voltage Estimator. The estimator DAC connected between VREF+ and VREF− generates the reference voltages for the six Voltage Estimator comparators. These comparators perform a very low resolution A/D conversion to obtain an “estimate” of the input voltage. This estimate is then used to control the Comparator Multiplexer, connecting the appropriate MSB Ladder section to the eight flash comparators. Only 14 comparators, six in the Voltage Estimator and eight in the flash converter, are needed to achieve the full eight-bit resolution, instead of 32 comparators that would be needed by traditional half-flash methods. 1108618 FIGURE 6. Block Diagram of the ADC08061/2 Multi-Step Flash Architecture A conversion begins with the Voltage Estimator comparing the analog input signal against the six tap voltages on the estimator DAC. The estimator decoder then selects one of the groups of tap points along the MSB Ladder. These eight tap points are then connected to the eight flash comparators. For example, if the analog input signal applied to VIN is between 0 and 3/16 of VREF (VREF = VREF+ − VREF−), the estimator decoder instructs the comparator multiplexer to select the eight tap points between 8/256 and 2/8 of VREF and connects them to the eight flash comparators. The first flash conversion is now performed, producing the five MSBs of data. The remaining three LSBs are generated next using the same eight comparators that were used for the first flash conversion. As determined by the results of the MSB flash, a voltage from the MSB Ladder equivalent to the magnitude of the five MSBs is subtracted from the analog input voltage as the upper switch is moved from position one to position two. The resulting remainder voltage is applied to the eight flash compara- 11 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 tors and, with the lower switch in position two, compared with the eight tap points from the LSB Ladder. By using the same eight comparators for both flash conversions, the number of comparators needed by the multi-step converter is significantly reduced when compared to standard half-flash techniques. Voltage Estimator errors as large as 1/16 of VREF (16 LSBs) will be corrected since the flash comparators are connected to ladder voltages that extend beyond the range specified by the Voltage Estimator. For example, if 7/16 VREF < VIN < 9/16 VREF the Voltage Estimator's comparators tied to the tap points below 9/16 VREF will output “1”s (000111). This is decoded by the estimator decoder to “10”. The eight flash comparators will be placed at the MSB Ladder tap points between ⅛ VREF and ⅛ VREF. The overlap of 1/16 VREF on each side of the Voltage Estimator's span will automatically correct an error of up to 16 LSBs (16 LSBs = 312.5 mV for VREF = 5V). If the first flash conversion determines that the input voltage is between ⅛ VREF and 4/8 VREF − LSB/2, the Voltage Estimator's output code will be corrected by subtracting “1”. This results in a corrected value of “01”. If the first flash conversion determines that the input voltage is between 8/16 VREF − LSB/2 and ⅛ VREF, the Voltage Estimator's output code remains unchanged. After correction, the 2-bit data from both the Voltage Estimator and the first flash conversion are decoded to produce the five MSBs. Decoding is similar to that of a 5-bit flash converter since there are 32 tap points on the MSB Ladder. However, 31 comparators are not needed since the Voltage Estimator places the eight comparators along the MSB Ladder where reference tap voltages are present that fall above and below the magnitude of VIN. Comparators are not needed outside this selected range. If a comparator's output is a “0”, all comparators above it will also have outputs of “0” and if a comparator's output is a “1”, all comparators below it will also have outputs of “1”. 2.0 DIGITAL INTERFACE The ADC08061/2 has two basic interface modes which are selected by connecting the MODE pin to a logic high or low. 2.1 RD Mode With a logic low applied to the MODE pin, the converter is set to Read mode. In this configuration (see Figure 1), a complete version is done by pulling RD low, and holding low, until the conversion is complete and output data appears. This typically takes 655 ns. The INT (interrupt) line goes low at the end of conversion. A typical delay of 50 ns is needed between the rising edge of RD (after the end of a conversion) and the start of the next conversion (by pulling RD low). The RDY output goes low after the falling edge of CS and goes high at the end-of-conversion. It can be used to signal a processor that the converter is busy or serve as a system Transfer Acknowledge signal. For the ADC08062 the data generated by the first conversion cycle after power-up is from an unknown channel. 2.2 RD Mode Pipelined Operation Applications that require shorter RD pulse widths than those used in the Read mode as described above can be achieved by setting RD's width between 200 ns–400 ns (Figure 5). RD pulse widths outside this range will create conversion linearity errors. These errors are caused by exercising internal interface logic circuitry using CS and/or RD during a conversion. When RD goes low, a conversion is initiated and the data from the previous conversion is available on the DB0–DB7 outputs. Reading D0–D7 for the first two times after power-up produces random data. The data will be valid during the third RD pulse that occurs after the first conversion. 2.3 WR-RD (WR then RD) Mode The ADC08061/2 is in the WR-RD mode with the MODE pin tied high. A conversion starts on the falling edge of the WR signal. There are two options for reading the output data which relate to interface timing. If an interrupt-driven scheme is desired, the user can wait for the INT output to go low before reading the conversion result (see Figure 3). Typically, INT will go low 520 ns, maximum, after WR 's rising edge. However, if a shorter conversion time is desired, the processor need not wait for INT and can exercise a read after only 350 ns (see Figure 2). If RD is pulled low before INT goes low, INT will immediately go low and data will appear at the outputs. This is the fastest operating mode (tRD ≤ tINTL) with a conversion time, including data access time, of 560 ns. Allowing 100 ns for reading the conversion data and the delay between conversions gives a total throughput time of 660 ns (throughput rate of 1.5 MHz). 2.4 WR-RD Mode with Reduced Interface System Connection CS and RD can be tied low, using only WR to control the start of conversion for applications that require reduced digital interface while operating in the WR-RD mode (Figure 4). Data will be valid approximately 705 ns following WR 's rising edge. 2.5 Multiplexer Addressing The ADC08062 has 2 multiplexer inputs. These are selected using the A0 multiplexer channel selection input. Table 1 shows the input code needed to select a given channel. The multiplexer address is latched when received but the multiplexer channel is updated after the completion of the current conversion. TABLE 1. Multiplexer Addressing ADC08062 A0 0 1 Channel VIN1 VIN2 The multiplexer address data must be valid at the time of RD's falling edge, remain valid during the conversion, and can go high after RD goes high when operating in the Read Mode. The multiplexer address data should be valid at or before the time of WR's falling edge, remain valid while WR is low, and go invalid after WR goes high when operating in the WR-RD Mode. 3.0 REFERENCE INPUTS The two VREF inputs of the ADC08061/2 are fully differential and define the zero to full-scale input range of the A to D converter. This allows the designer to vary the span of the analog input since this range will be equivalent to the voltage difference between VREF+ and VREF−. Transducers with minimum output voltages above GND can also be compensated by connecting VREF− to a voltage that is equal to this minimum voltage. By reducing VREF (VREF = VREF+ − VREF−) to less than 5V, the sensitivity of the converter can be increased (i.e., if VREF = 2.5V, then 1 LSB = 9.8 mV). The ADC08061/2's reference arrangement also facilitates ratiometric operation and in many cases the ADC08061/2's power supply can be used 12 www.national.com 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 for transducer power as well as the VREF source. Ratiometric operation is achieved by connecting VREF− to GND and connecting VREF+ and a transducer's power supply input to V+. The ADC08061/2's linearity degrades when VREF+ − |VREF−| is less than 2.0V. The voltage at VREF− sets the input level that produces a digital output of all zeros. Though VIN is not itself differential, the reference design affords nearly differential-input capability for some measurement applications. Figure 7 shows one possible differential configuration. It should be noted that, while the two VREF inputs are fully differential, the digital output will be zero for any analog input voltage if VREF− ≥ VREF+. 4.0 ANALOG INPUT AND SOURCE IMPEDANCE The ADC08061/2's analog input circuitry includes an analog switch with an “on” resistance of 70Ω and capacitance of 1.4 pF and 12 pF (see Figure 7). The switch is closed during the A/D's input signal acquisition time (while WR is low when using the WR -RD Mode). A small transient current flows into the input pin each time the switch closes. A transient voltage, whose magnitude can increase as the source impedance increases, may be present at the input. So long as the source impedance is less than 500Ω, the input voltage transient will not cause errors and need not be filtered. Large source impedances can slow the charging of the sampling capacitors and degrade conversion accuracy. Therefore, only signal sources with output impedances less than 500Ω should be used if rated accuracy is to be achieved at the minimum sample time (100 ns maximum). A signal source with a high output impedance should have its output buffered with an operational amplifier. Any ringing or voltage shifts at the op amp's output during the sampling period can result in conversion errors. Correct conversion results will be obtained for input voltages greater than GND − 100 mV and less than V+ + 100 mV. Do not allow the signal source to drive the analog input pin more than 300 mV higher than V+, or more than 300 mV lower than GND. The current flowing through any analog input pin should be limited to 5 mA or less to avoid permanent damage to the IC if an analog input pin is forced beyond these voltages. The sum of all the overdrive currents into all pins must be less than 20 mA. Some sort of protection scheme should be used when the input signal is expected to extend more than 300 mV beyond the power supply limits. A simple protection network using resistors and diodes is shown in Figure 9. 6.0 INHERENT SAMPLE-AND-HOLD An important benefit of the ADC08061/2's input architecture is the inherent sample-and-hold (S/H) and its ability to measure relatively high speed signals without the help of an external S/H. In a non-sampling converter, regardless of its speed, the input must remain stable to at least ½ LSB throughout the conversion process if full accuracy is to be maintained. Consequently, for many high speed signals, this signal must be externally sampled and held stationary during the conversion. The ADC08061 and ADC08062 are suitable for DSP-based systems because of the direct control of the S/H through the WR signal. The WR input signal allows the A/D to be synchronized to a DSP system's sampling rate or to other ADC08061 and ADC08062s. 1108619 *Represents a multiplexer channel in the ADC08062. FIGURE 7. ADC08061 and ADC08062 Equivalent Input Circuit Model External Reference 2.5V Full-Scale (Standard Application) Power Supply as Reference 1108621 1108620 Note : Bypass capacitors consist of a 0.1 µF ceramic in parallel with a 10 µF bead tantalum. 13 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 Input Not Referred to GND * Signal source driving VIN(−) must be capable of sinking 5 mA. 1108622 FIGURE 8. Analog Input Options 1108623 Note the multiple bypass capacitors on the reference and power supply pins. VREF− should be bypass to analog ground using multiple capacitors if it is not grounded (see Section 7.0 “Layout, Grounds, and Bypassing”). VIN1 is shown with an optional input protection network. FIGURE 9. Typical Connection The analog inputs should be isolated from noisy signal traces to avoid having spurious signals couple to the input. Any external component (e.g., an input filter capacitor) connected across the inputs should be returned to a very clean ground point. Incorrectly grounding the ADC08061/2 will result in reduced conversion accuracy. The V+ supply pin, VREF+, and VREF− (if not grounded) should be bypassed with a parallel combination of a 0.1 µF ceramic capacitor and a 10 µF tantalum capacitor placed as close as possible to the supply pin using short circuit board traces. See Figures 8, 9. The ADC08061 can perform accurate conversions of fullscale input signals at frequencies from DC to more than 300 kHz (full power bandwidth) without the need of an external sample-and-hold (S/H). 7.0 LAYOUT, GROUNDS, AND BYPASSING In order to ensure fast, accurate conversions from the ADC08061/2, it is necessary to use appropriate circuit board layout techniques. Ideally, the analog-to-digital converter's ground reference should be low impedance and free of noise from other parts of the system. Digital circuits can produce a great deal of noise on their ground returns and, therefore, should have their own separate ground lines. Best performance is obtained using separate ground planes for the digital and analog parts of the system. www.national.com 11086 Version 6 Revision 2 14 Print Date/Time: 2009/07/15 15:48:35 ADC08061/ADC08062 Physical Dimensions inches (millimeters) unless otherwise noted Wide-Body Small-Outline Package (M) Order Number ADC08061CIWM, or ADC08062CIWM NS Package Number M20B Dual-In-Line Package (N) Order Number ADC08061BIN or ADC08062BIN NS Package Number N20A 15 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35 www.national.com ADC08061/ADC08062 500 ns A/D Converter with S/H Function and Input Multiplexer Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers Audio Clock and Timing Data Converters Interface LVDS Power Management Switching Regulators LDOs LED Lighting Voltage Reference PowerWise® Solutions Temperature Sensors Wireless (PLL/VCO) www.national.com/amplifiers www.national.com/audio www.national.com/timing www.national.com/adc www.national.com/interface www.national.com/lvds www.national.com/power www.national.com/switchers www.national.com/ldo www.national.com/led www.national.com/vref www.national.com/powerwise WEBENCH® Tools App Notes Reference Designs Samples Eval Boards Packaging Green Compliance Distributors Quality and Reliability Feedback/Support Design Made Easy Solutions Mil/Aero PowerWise® Design University Design Support www.national.com/webench www.national.com/appnotes www.national.com/refdesigns www.national.com/samples www.national.com/evalboards www.national.com/packaging www.national.com/quality/green www.national.com/contacts www.national.com/quality www.national.com/feedback www.national.com/easy www.national.com/solutions www.national.com/milaero www.national.com/solarmagic www.national.com/training Serial Digital Interface (SDI) www.national.com/sdi www.national.com/wireless www.national.com/tempsensors SolarMagic™ THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com 11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35