CRCW060316K2FKEA

LM3492 Evaluation Board Reference Design LM3492 Evaluation Board Reference Design National Semiconductor Application Note 2056 L.K. Wong September 21, 2010 Introduction The LM3492 integrates a boost converter and a two-channel current regulator to implement a high efficient and cost effective LED driver for driving two individually dimmable LED strings with a maximum power of 15W and an output voltage of up to 65V. The boost converter employs a proprietary Projected-On-Time control method to give a fast transient response with no compensation required, and a nearly constant switching frequency programmable from 200 kHz to 1 MHz. The application circuit is stable with ceramic capacitors and produces no audible noise on dimming. The programmable peak current limit and soft-start features reduce current surges at startup, and an integrated 190 mΩ, 3.9A N-Channel MOSFET switch minimizes the solution size. The fast slew rate current regulator allows high frequency and narrow pulse width dimming signals to achieve a very high contrast ratio of 1000:1 at a dimming frequency of more than 3 kHz. The LED current is programmable from 50 mA to 200 mA by a single resistor. To maximize the efficiency, Dynamic Headroom Control (DHC) automatically adjusts the output voltage to a minimum. DHC also facilitates a single BOM for different number of LED in a string, which is required for backlight panels of different size, thereby reducing overall development time and cost. The LM3492 comes with a versatile COMM pin which serves as a bi-directional I/O pin interfacing with an external MCU for the following functions: power-good, over-temperature, IOUT over- and under-voltage indications, switching frequency tuning, and channel 1 disabling. Other supervisory functions of the LM3492 include precise enable, VCC under-voltage lockout, current regulator Over-Power protection, and thermal shutdown protection. The LM3492 is available in the thermally enhanced eTSSOP-20 package. This application note details the design of a LM3492 evaluation board which drives 2 LED strings, each of which consists of 10 LEDs running at 150 mA and the forward voltage of each LED is typically 3.8V. The input voltage is from 9V to 16V. The evaluation board schematic, PCB layout, Bill of Materials, and circuit design descriptions are shown. Typical performance and operating waveforms are also provided for reference. Evaluation Board Schematic and PCB Layout 30123301 FIGURE 1. LM3492 Evaluation Board Schematic AN-2056 © 2010 National Semiconductor Corporation 301233 www.national.com AN-2056 30123302 FIGURE 2. LM3492 Evaluation Board Top Overlay 30123303 FIGURE 3. LM3492 Evaluation Board Top View 30123304 FIGURE 4. LM3492 Evaluation Board Bottom View www.national.com 2 AN-2056 Evaluation Board Quick Setup Procedures Step 1 2 3 4 5 Description Connect a power supply to VIN and PGND terminals Connect 2 LED strings: from VLED1 to IOUT1 terminals, and VLED2 to IOUT2 terminals The EN terminal should be left open for normal operation. Ground this terminal to shutdown Connect DIM1 and DIM2 terminals to a voltage > 2V, apply VIN = 12V Ground the EN terminal to check the shutdown function Evaluation Board Performance Characteristic Description Input Voltage Rail Voltage LED Current LED Current Regulationt Efficiency Symbol VIN VOUT ILED ΔILED ALL VIN conditions VIN = 9V VIN = 12V VIN = 16V -3 85.7 88.2 89.1 L1 = (VIN(MAX) x ton) / 2IIN(MIN) Condition Min 9 Typ 12 39 150 +3 Max 16 Unit V V mA % % % % (4) Nominal LED current is 150 mA per channel Notes VIN range: 9V to 16V Each LED string consists of 10 LEDs with a forward voltage of 3.8V per LED at 150 mA Design Procedure The following procedures detail the design of the LM3492 evaluation board driving 2 LED strings consists of 10 LEDs per string. The forward voltage of each LED is 3.8V, and the LED current is 150 mA. The input voltage is ranged from 9V to 16V. The switching frequency fSW is designed to be 500 kHz. Design Parameters: VIN = 9V to 16V, typical 12V ILED = 150 mA Step 1: Calculate the output voltage feedback circuit The nominal voltage of the LED string with 10 LEDs is 38V, and the minimum voltage of the IOUTn pin (n = 1, 2) is 0.75V for an ILED of 150 mA. Hence, VOUT(NOM) is 38.75V. Since the dynamic range of VFB under DHC is from 1.05V to 2V, the nominal voltage on the FB pin VFB(NOM) is designed to be around 1.5V. Hence, VOUT(MAX) is designed to be 65V. Since VOUT(MAX) = 2.5V (1 + RFB1/ RFB2) (1) By designing RFB2 to be 16.2 kΩ, RFB1 is calculated to be 405 kΩ, and a standard resistor value of 402 kΩ is selected. CFB1 is selected to be 10 pF as recommended. Step 2: Determine the inductance The main parameter affected by the inductor is the peak to peak inductor current ripple (ILR). To maintain a continuous conduction mode (CCM) operation, the average inductor current IL1 should be larger than half of ILR. For a boost converter, IL1 equals to the input current IIN. The minimum IIN occurs when VIN is maximum, which is 16V in this example, and only 1 LED string is turned on (the 2 LED strings are individually dimmable). Hence, IIN(MIN) = (VOUT(NOM) x ILED) / VIN(MAX) Also ton = (1 – VIN/VOUT) / fSW To ensure a CCM operation, (3) (2) It can be calculated that IIN(MIN), ton, and L1 are 0.363A, 1.17 µs, and 25.8 µH. On the other hand, IIN is maximum when VIN is minimum, which is 9V in this example, and 2 LED strings are turned on. Hence IIN(MAX) is 1.29A. From (3), ton is 1.54 µs when VIN is 9V. Then ILR is ILR = (VIN x ton) / L1 (5) From (5), ILR is 0.53A. The steady state peak inductor current IL1(PEAK) is IL1(PEAK) = IL1 + ILR / 2 (6) As a result, IL1(PEAK) is 1.56A. A standard value of 27 µH is selected for L1, and the saturation current of L1 should be larger than 1.56A. Step 3: Determine the diode The selection of the boost diode D1 depends on two factors. The first factor is the reverse voltage, which equals to VOUT in a boost converter. The second factor is the peak diode current at the steady state, which equals to the peak inductor current as shown in (6). In this example, a 100V 3A schottky diode is selected. Step 4: Determine the value of other components CIN and COUT: The function of the input capacitor CIN and the output capacitor COUT is to reduce the input and output voltage ripples. Experimentation is usually necessary to determine their value. The rated DC voltage of capacitors used should be higher than the maximum DC voltage applied. Owing to the concern of product lifetime, ceramic capacitors are recommended. But ceramic capacitors with high rated DC voltage and high capacitance are rare in general. Multiple capacitors connecting in parallel can be used for CIN and COUT. In this example, two 10 µF 25V ceramic capacitor are used for CIN, and two 2.2 µF 100V ceramic capacitor are used for COUT. CVCC: The capacitor on the VCC pin provides noise filtering and stabilizes the LDO regulator. It also prevents false trig- 3 www.national.com AN-2056 gering of the VCC UVLO. CVCC is recommended to be a 1 µF good quality and low ESR ceramic capacitor. CCDHC: The capacitor at the CDHC pin mainly determines the soft-start time tSS, i.e. the time for the output voltage to reach its maximum. tSS is determined from the following equation: (7) In this example, CCDHC is recommended to be a 0.47 µF good quality and low ESR ceramic capacitor. RRT and RIREF: The resistors RRT and RIREF set the switching frequency fSW of the boost converter and the LED current ILED respectively. From the LM3492 datasheet, RRT is selected to be 274 kΩ if fSW is 500 kHz (Figure 1 of the datasheet), and RIREF is selected to be 8.25 kΩ if ILED is 150 mA (Figure 4 of the datasheet). RCOMM: Since the COMM pin is open drain, a resistor RCOMM of 52.3 kΩ is used to connect the VCC and COMM pins to implement a pull-up function. external components should be placed as close to the LM3492 and each other as possible in order to make copper traces short and direct. In particular, components of the boost converter CIN, L1, D1, COUT, and the LM3492 should be closed. Also, the output feedback capacitor CFB1 should be closed to the output capacitor COUT. The ground plane connecting the GND, PGND, and LGND pins and the exposed pad of the LM3492 and the ground connection of the CIN and COUT should be placed on the same copper layer. Good heat dissipation helps optimize the performance of the LM3492. The ground plane should be used to connect the exposed pad of the LM3492, which is internally connected to the LM3492 die substrate. The area of the ground plane should be extended as much as possible on the same copper layer around the LM3492. Using numerous vias beneath the exposed pad to dissipate heat of the LM3492 to another copper layer is also a good practice. PC Board Layout The layout of the printed circuit board is critical to optimize the performance of the LM3492 application circuit. In general, www.national.com 4 AN-2056 Bill of Materials Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part Number GRM31CR61E106KA12L GRM188R71C474KA88D GRM1885C2A100RA01D GRM188R71C105KA12D GRM32ER72A225KA35L CRCW060352K3FKEA CRCW0603274KFKEA CRCW0603402KFKEA CRCW060316K2FKEA CRCW06038K25FKEA CRCW06030000Z0EA CDRH10D68/ANP-270MC SK310A-TP 1502-2k-ND Mfg name muRata muRata muRata muRata muRata Vishay Vishay Vishay Vishay Vishay Vishay Sumida KEYSTONE Part Description Cap 10 µF 25V X5R 0603/X7R/0.47 µF/16V 0603/COG/10 pF/100V 0603/X7R/1 µF/16V Cap 2.2uF 100V X7R Resistor Chip 52.3 kΩ 1% Resistor Chip 274 kΩ 1% Resistor Chip 402 kΩ 1% Resistor Chip 16.2 kΩ 1% Resistor Chip 8.25 kΩ 1% Resistor Chip 0Ω 1% Inductor 27 µH 1.9A Terminal DBL Turret 0.109”L Brass Qty 2 1 1 1 2 1 1 1 1 1 1 1 1 11 Ref Designator(s) CIN1, CIN2 CCDHC CFB1 CVCC CO1, CO2 RCOMM RRT RFB1 RFB2 RIREF RILIM0 L1 D1 VIN, GND, PGND, VLED1, VLED2, IOUT1, IOUT2, DIM1, DIM2, COMM, EN PCB U1 eTSSOP-20 Size 1206 0603 0603 0603 1210 0603 0603 0603 0603 0603 0603 10×10×6.8 SMA Micro Commercial Schottky 100V 3A 15 16 LM3492EVAL LM3492MH NSC NSC LM3492 demo board IC LM3492 1 1 5 www.national.com AN-2056 Typical Performance and Waveforms board and TA = 25°C unless otherwise specified. Efficiency vs Input Voltage (ILED = 150 mA) All curves and waveforms taken at VIN = 12V with the evaluation ILED Regulation vs Input Voltage (ILED = 150 mA) 30123306 30123307 Steady State Operation (VIN = 12V, ILED = 150 mA) LED 50% Dimming (VIN = 12V, ILED = 150 mA) 30123308 30123309 Power Up (VIN = 12V, ILED = 150 mA) Enable Transient (VIN = 12V, ILED = 150 mA) 30123310 30123311 www.national.com 6 AN-2056 7 www.national.com LM3492 Evaluation Board Reference Design Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Amplifiers Audio Clock and Timing Data Converters Interface LVDS Power Management Switching Regulators LDOs LED Lighting Voltage References PowerWise® Solutions Temperature Sensors PLL/VCO www.national.com/amplifiers www.national.com/audio www.national.com/timing www.national.com/adc www.national.com/interface www.national.com/lvds www.national.com/power www.national.com/switchers www.national.com/ldo www.national.com/led www.national.com/vref www.national.com/powerwise WEBENCH® Tools App Notes Reference Designs Samples Eval Boards Packaging Green Compliance Distributors Quality and Reliability Feedback/Support Design Made Easy Design Support www.national.com/webench www.national.com/appnotes www.national.com/refdesigns www.national.com/samples www.national.com/evalboards www.national.com/packaging www.national.com/quality/green www.national.com/contacts www.national.com/quality www.national.com/feedback www.national.com/easy www.national.com/solutions www.national.com/milaero www.national.com/solarmagic www.national.com/training Applications & Markets Mil/Aero PowerWise® Design University Serial Digital Interface (SDI) www.national.com/sdi www.national.com/wireless www.national.com/tempsensors SolarMagic™ THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2010 National Semiconductor Corporation AN-2056 For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com