LM285Z

LM185/LM285/LM385 Adjustable Micropower Voltage Reference February 2005 LM185/LM285/LM385 Adjustable Micropower Voltage References General Description The LM185/LM285/LM385 are micropower 3-terminal adjustable band-gap voltage reference diodes. Operating from 1.24 to 5.3V and over a 10µA to 20mA current range, they feature exceptionally low dynamic impedance and good temperature stability. On-chip trimming is used to provide tight voltage tolerance. Since the LM185 band-gap reference uses only transistors and resistors, low noise and good long-term stability result. Careful design of the LM185 has made the device tolerant of capacitive loading, making it easy to use in almost any reference application. The wide dynamic operating range allows its use with widely varying supplies with excellent regulation. The extremely low power drain of the LM185 makes it useful for micropower circuitry. This voltage reference can be used to make portable meters, regulators or general purpose analog circuitry with battery life approaching shelf life. Further, the wide operating current allows it to replace older references with a tighter tolerance part. The LM185 is rated for operation over a −55˚C to 125˚C temperature range, while the LM285 is rated −40˚C to 85˚C and the LM385 0˚C to 70˚C. The LM185 is available in a hermetic TO-46 package and a leadless chip carrier package, while the LM285/LM385 are available in a low-cost TO-92 molded package, as well as S.O. Features n n n n n Adjustable from 1.24V to 5.30V Operating current of 10µA to 20mA 1% and 2% initial tolerance 1Ω dynamic impedance Low temperature coefficient Connection Diagrams TO-92 Plastic Package TO-46 Metal Can Package 00525009 Bottom View 00525001 Bottom View 20-Leadless Chip Carrier SOIC Package 00525010 Top View Top View 00525015 © 2005 National Semiconductor Corporation DS005250 www.national.com LM185/LM285/LM385 Ordering Information Package −55˚C to 125˚C LM185BH TO-46 LM185BH/883 LM185BYH LM185BYH/883 LM285BXZ TO-92 LM285BYZ LM285Z LM285M LM285BYM LM185BE/883 LM385BXZ LM385BYZ LM385BZ LM385Z 8-Pin SOIC 20-Leadless Chip Carrier LM385M LM385BM M08A E20A Z03A H03H Temperature Range −40˚C to 85˚C 0˚C to 70˚C NSC Drawing Block Diagram 00525013 Typical Applications 1.2V Reference 5.0V Reference 00525014 00525002 www.national.com 2 LM185/LM285/LM385 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (Note 2) Reverse Current Forward Current Operating Temperature Range (Note 3) LM185 Series LM285 Series LM385 Series −55˚C to 125˚C −40˚C to 85˚C 0˚C to 70˚C 30mA 10mA Storage Temperature Soldering Information TO-92 Package (10 sec.) TO-46 Package (10 sec.) SO Package Vapor Phase (60 sec.) Infrared (15 sec.) −55˚C to 150˚C 260˚C 300˚C 215˚C 220˚C See An-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. Electrical Characteristics (Note 4) LM185, LM285 LM185BX, LM185BY LM185B, LM285BX, Typ LM285BY Tested Design Tested Design Limit (Note 5) Reference Voltage IR = 100µA 1.240 1.252 1.255 1.228 1.215 Reference Voltage Change with Current Impedance IMIN < IR < 1mA 1mA < IR < 20mA 0.2 4 1 10 1.5 20 1 10 1.5 20 0.2 5 1 15 1.5 25 1 15 1.5 25 1.215 1.205 1.228 1.215 1.215 1.205 Limit (Note 6) Limit (Note 5) 1.265 Limit (Note 6) LM285 Typ Tested Design Tested Design Limit (Note 5) Limit (Note 6) 1.255 Limit (Note 5) 1.265 Limit (Note 6) 1.270 V (max) V (min) mV (max) LM385 LM385BX, LM385BY LM385 Units (Limit) Parameter Conditions 1.270 1.240 1.252 Dynamic Output IR = 100µA, f = 100Hz IAC = 0.1 IR VOUT = VREF VOUT = 5.3V Reference Voltage Change with Output Voltage Feedback Current Minimum Operating Current (see curve) Output Wideband Noise VOUT = VREF VOUT = 5.3V IR = 100µA, 10Hz < f < 10kHz VOUT = VREF VOUT = 5.3V 50 170 50 170 µVrms 13 6 30 20 9 45 25 10 50 20 9 45 25 10 50 16 7 35 30 11 55 35 13 60 30 11 55 35 13 60 nA (max) µA (max) IR = 100µA 1 3 6 3 6 2 5 10 5 10 0.3 0.7 0.4 1 Ω mV (max) 3 www.national.com LM185/LM285/LM385 Electrical Characteristics (Note 4) (Continued) LM185, LM285 LM385 LM385BX, LM285 Typ Tested Design Tested Design Limit (Note 5) 30 50 150 150 20 150 150 ppm Limit (Note 6) Limit (Note 5) Limit (Note 6) ppm/˚c (max) Limit (Note 5) Limit (Note 6) LM385BY LM385 Units (Limit) LM185BX, LM185BY LM185B, LM285BX, Typ LM285BY Tested Design Tested Design Limit (Note 5) Average Temperature Coefficient (Note 7) Long Term Stability IR = 100µA X Suffix Y Suffix All Others IR = 100µA, T = 1000 Hr, TA = 25˚C ± 0.1˚C 20 30 50 Limit (Note 6) Parameter Conditions Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Refer to RETS185H for military specifications. Note 3: For elevated temperature operation, TJmax is: LM185 LM285 LM385 Thermal Resistance θJA (Junction to Ambient) θJC (Junction to Case) 150˚C 125˚C 100˚C TO-92 TO-46 SO-8 180˚C/W (0.4" leads) 170˚C/W (0.125" leads) N/A 440˚C/W 165˚C/W 80˚C/W N/A Note 4: Parameters identified with boldface type apply at temperature extremes. All other numbers apply at TA = TJ = 25˚C. Unless otherwise specified, all parameters apply for VREF < VOUT < 5.3V. Note 5: Guaranteed and 100% production tested. Note 6: Guaranteed, but not 100% production tested. These limits are not to be used to calculate average outgoing quality levels. Note 7: The average temperature coefficient is defined as the maximum deviation of reference voltage at all measured temperatures from TMIN to TMAX, divided by TMAX − TMIN. The measured temperatures are −55, −40, 0, 25, 70, 85, 125˚C. www.national.com 4 LM185/LM285/LM385 Typical Performance Characteristics Temperature Drift of 3 Representative Units Feedback Current 00525016 00525017 Minimum Operating Current Reverse Characteristics 00525018 00525019 Reverse Characteristics Forward Characteristics 00525020 00525021 5 www.national.com LM185/LM285/LM385 Typical Performance Characteristics Output Noise Voltage (Continued) Dynamic Output Impedance 00525022 00525023 Response Time 00525024 Temperature Coefficient Typical LM185 LM285 LM385 00525004 www.national.com 6 LM185/LM285/LM385 Typical Applications Precision 10V Reference Low AC Noise Reference 00525025 00525026 25V Low Current Shunt Regulator 200 mA Shunt Regulator 00525027 00525028 7 www.national.com LM185/LM285/LM385 Typical Applications (Continued) High Efficiency Low Power Regulator Series-Shunt 20 mA Regulator 00525029 00525030 Voltage Level Detector Voltage Level Detector 00525031 00525032 Fast Positive Clamp 2.4V + ∆VD1 Bidirectional Clamp ± 2.4V 00525034 00525033 www.national.com 8 LM185/LM285/LM385 Typical Applications (Continued) Bidirectional Adjustable Clamp ± 2.4V to ± 6V Bidirectional Adjustable Clamp ± 1.8V to ± 2.4V 00525035 00525036 Simple Floating Current Detector Current Source 00525038 00525037 9 www.national.com LM185/LM285/LM385 Typical Applications (Continued) Precision Floating Current Detector 00525039 *D1 can be any LED, VF=1.5V to 2.2V at 3 mA. D1 may act as an indicator. D1 will be on if ITHRESHOLD falls below the threshold current, except with I=O. Centigrade Thermometer, 10mV/˚C Freezer Alarm 00525011 00525012 www.national.com 10 LM185/LM285/LM385 Schematic Diagram 00525008 11 www.national.com LM185/LM285/LM385 Physical Dimensions unless otherwise noted inches (millimeters) 20-Leadless Chip Carrier (E) NS Package Number E20A TO-46 Metal Can Package (H) NS Package Number H03H www.national.com 12 LM185/LM285/LM385 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) SO Package (M) NS Package Number M08A TO-92 Plastic Package (Z) NS Package Number Z03A 13 www.national.com LM185/LM285/LM385 Adjustable Micropower Voltage Reference Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.