LM34DZ

LM34 Precision Fahrenheit Temperature Sensors July 1999 LM34 Precision Fahrenheit Temperature Sensors General Description The LM34 series are precision integrated-circuit temperature sensors, whose output voltage is linearly proportional to the Fahrenheit temperature. The LM34 thus has an advantage over linear temperature sensors calibrated in degrees Kelvin, as the user is not required to subtract a large constant voltage from its output to obtain convenient Fahrenheit scaling. The LM34 does not require any external calibration or trimming to provide typical accuracies of ± 1⁄2˚F at room temperature and ± 11⁄2˚F over a full −50 to +300˚F temperature range. Low cost is assured by trimming and calibration at the wafer level. The LM34’s low output impedance, linear output, and precise inherent calibration make interfacing to readout or control circuitry especially easy. It can be used with single power supplies or with plus and minus supplies. As it draws only 75 µA from its supply, it has very low self-heating, less than 0.2˚F in still air. The LM34 is rated to operate over a −50˚ to +300˚F temperature range, while the LM34C is rated for a −40˚ to +230˚F range (0˚F with improved accuracy). The LM34 series is available packaged in hermetic TO-46 transistor packages, while the LM34C, LM34CA and LM34D are also available in the plastic TO-92 transistor package. The LM34D is also available in an 8-lead surface mount small outline package. The LM34 is a complement to the LM35 (Centigrade) temperature sensor. Features n n n n n n n n n n n Calibrated directly in degrees Fahrenheit Linear +10.0 mV/˚F scale factor 1.0˚F accuracy guaranteed (at +77˚F) Rated for full −50˚ to +300˚F range Suitable for remote applications Low cost due to wafer-level trimming Operates from 5 to 30 volts Less than 90 µA current drain Low self-heating, 0.18˚F in still air Nonlinearity only ± 0.5˚F typical Low-impedance output, 0.4Ω for 1 mA load Connection Diagrams TO-46 Metal Can Package (Note 1) TO-92 Plastic Package SO-8 Small Outline Molded Package DS006685-1 DS006685-2 Order Numbers LM34H, LM34AH, LM34CH, LM34CAH or LM34DH See NS Package Number H03H Order Number LM34CZ, LM34CAZ or LM34DZ See NS Package Number Z03A DS006685-20 N.C. = No Connection Top View Order Number LM34DM See NS Package Number M08A Note 1: Case is connected to negative pin (GND). TRI-STATE ® is a registered trademark of National Semiconductor Corporation. © 1999 National Semiconductor Corporation DS006685 www.national.com Typical Applications DS006685-3 FIGURE 1. Basic Fahrenheit Temperature Sensor (+5˚ to +300˚F) DS006685-4 FIGURE 2. Full-Range Fahrenheit Temperature Sensor www.national.com 2 Absolute Maximum Ratings (Note 11) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Output Voltage Output Current Storage Temperature, TO-46 Package TO-92 Package SO-8 Package ESD Susceptibility (Note 12) Lead Temp. +35V to −0.2V +6V to −1.0V 10 mA −76˚F to +356˚F −76˚F to +300˚F −65˚C to +150˚C 800V TO-46 Package (Soldering, 10 seconds) TO-92 Package (Soldering, 10 seconds) SO Package (Note 13) Vapor Phase (60 seconds) Infrared (15 seconds) Specified Operating Temp. Range (Note 3) LM34, LM34A LM34C, LM34CA LM34D +300˚C +260˚C 215˚C 220˚C TMIN to TMAX −50˚F to +300˚F −40˚F to +230˚F +32˚F to +212˚F DC Electrical Characteristics (Notes 2, 7) LM34A Parameter Conditions Typical Accuracy (Note 8) TA = +77˚F TA = 0˚F TA = TMAX TA = TMIN Nonlinearity (Note 9) Sensor Gain (Average Slope) Load Regulation (Note 4) Line Regulation (Note 4) Quiescent Current (Note 10) TA = +77˚F TMIN ≤ TA ≤ TMAX 0 ≤ IL ≤ 1 mA TA = +77˚F 5V ≤ VS ≤ 30V VS = +5V, +77˚F VS = +5V VS = +30V, +77˚F VS = +30V 4V ≤ VS ≤ 30V, +77˚F 5V ≤ VS ≤ 30V TMIN ≤ TA ≤ TMAX TMIN ≤ TA ≤ TMAX Tested Limit (Note 5) Design Limit (Note 6) Typical LM34CA Tested Limit (Note 5) Design Limit (Note 6) ˚F Units (Max) ± 0.4 ± 0.6 ± 0.8 ± 0.8 ± 0.35 +10.0 ± 1.0 ± 2.0 ± 2.0 ± 0.7 +9.9, +10.1 ± 0.4 ± 0.6 ± 0.8 ± 0.8 ± 0.30 +10.0 ± 1.0 ± 2.0 ± 2.0 ± 3.0 ± 0.6 +9.9, +10.1 ˚F ˚F ˚F ˚F mV/˚F, min mV/˚F, max mV/mA mV/mA mV/V ± 0.4 ± 0.5 ± 0.01 ± 0.02 75 131 76 132 +0.5 +1.0 +0.30 ± 1.0 ± 3.0 ± 0.05 ± 0.1 90 160 92 163 2.0 3.0 +0.5 +5.0 ± 0.4 ± 0.5 ± 0.01 ± 0.02 75 116 76 117 0.5 1.0 +0.30 +3.0 ± 1.0 ± 3.0 ± 0.05 ± 0.1 90 139 92 142 2.0 3.0 +0.5 +5.0 mV/V µA µA µA µA µA µA µA/˚F ˚F ˚F Change of Quiescent Current (Note 4) Temperature Coefficient of Quiescent Current Minimum Temperature for Rated Accuracy Long-Term Stability In circuit of Figure 1, IL = 0 Tj = TMAX for 1000 hours +3.0 ± 0.16 ± 0.16 Note 2: Unless otherwise noted, these specifications apply: −50˚F ≤ Tj ≤ + 300˚F for the LM34 and LM34A; −40˚F ≤ Tj ≤ +230˚F for the LM34C and LM34CA; and +32˚F ≤ Tj ≤ + 212˚F for the LM34D. VS = +5 Vdc and ILOAD = 50 µA in the circuit of Figure 2; +6 Vdc for LM34 and LM34A for 230˚F ≤ Tj ≤ 300˚F. These specifications also apply from +5˚F to TMAX in the circuit of Figure 1. Note 3: Thermal resistance of the TO-46 package is 720˚F/W junction to ambient and 43˚F/W junction to case. Thermal resistance of the TO-92 package is 324˚F/W junction to ambient. Thermal resistance of the small outline molded package is 400˚F/W junction to ambient. For additional thermal resistance information see table in the Typical Applications section. Note 4: Regulation is measured at constant junction temperature using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. Note 5: Tested limits are guaranteed and 100% tested in production. Note 6: Design limits are guaranteed (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are not used to calculate outgoing quality levels. Note 7: Specification in BOLDFACE TYPE apply over the full rated temperature range. 3 www.national.com DC Electrical Characteristics (Notes 2, 7) (Continued) Note 8: Accuracy is defined as the error between the output voltage and 10 mV/˚F times the device’s case temperature at specified conditions of voltage, current, and temperature (expressed in ˚F). Note 9: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line over the device’s rated temperature range. Note 10: Quiescent current is defined in the circuit of Figure 1. Note 11: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its rated operating conditions (Note 2). Note 12: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Note 13: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National Semiconductor Linear Data Book for other methods of soldering surface mount devices. DC Electrical Characteristics (Notes 2, 7) LM34 Parameter Conditions Typical Accuracy, LM34, LM34C (Note 8) TA = +77˚F TA = 0˚F TA = TMAX TA = TMIN TA = +77˚F TA = TMAX TA = TMIN TMIN ≤ TA ≤ TMAX TMIN ≤ TA ≤ TMAX TA = +77˚F TMIN ≤ TA ≤ +150˚F 0 ≤ IL ≤ 1 mA TA = +77˚F 5V ≤ VS ≤ 30V VS = +5V, +77˚F VS = +5V VS = +30V, +77˚F VS = +30V 4V ≤ VS ≤ 30V, +77˚F 5V ≤ VS ≤ 30V Tested Limit (Note 5) Design Limit (Note 6) Typical LM34C, LM34D Tested Limit (Note 5) Design Limit (Note 6) ˚F Units (Max) ± 0.8 ± 1.0 ± 1.6 ± 1.6 ± 2.0 ± 3.0 ± 3.0 Accuracy, LM34D (Note 8) Nonlinearity (Note 9) Sensor Gain (Average Slope) Load Regulation (Note 4) Line Regulation (Note 4) Quiescent Current (Note 10) ± 0.6 +10.0 +9.8, +10.2 ± 1.0 ± 0.8 ± 1.0 ± 1.6 ± 1.6 ± 1.2 ± 1.8 ± 1.8 ± 0.4 +10.0 ± 2.0 ± 3.0 ± 3.0 ± 4.0 ± 3.0 ± 4.0 ± 4.0 ± 1.0 +9.8, +10.2 ˚F ˚F ˚F ˚F ˚F ˚F ˚F mV/˚F, min mV/˚F, max mV/mA mV/mA mV/V ± 0.4 ± 0.5 ± 0.01 ± 0.02 75 131 76 132 +0.5 +1.0 +0.30 ± 2.5 ± 6.0 ± 0.1 ± 0.2 100 176 103 181 3.0 5.0 +0.7 +5.0 ± 0.4 ± 0.5 ± 0.01 ± 0.02 75 116 76 117 0.5 1.0 +0.30 +3.0 ± 2.5 ± 6.0 ± 0.1 ± 0.2 100 154 103 159 3.0 5.0 +0.7 +5.0 mV/V µA µA µA µA µA µA µA/˚F ˚F ˚F Change of Quiescent Current (Note 4) Temperature Coefficient of Quiescent Current Minimum Temperature for Rated Accuracy Long-Term Stability In circuit of Figure 1, IL = 0 Tj = TMAX for 1000 hours +3.0 ± 0.16 ± 0.16 www.national.com 4 Typical Performance Characteristics Thermal Resistance Junction to Air Thermal Time Constant Thermal Response in Still Air DS006685-23 DS006685-22 DS006685-24 Thermal Response in Stirred Oil Bath Minimum Supply Voltage vs. Temperature Quiescent Current vs. Temperature (In Circuit of Figure 1) DS006685-25 DS006685-26 DS006685-27 Quiescent Current vs. Temperature (In Circuit of Figure 2; −VS = −5V, R1 = 100k) Accuracy vs. Temperature (Guaranteed) Accuracy vs. Temperature (Guaranteed) DS006685-29 DS006685-28 DS006685-30 5 www.national.com Typical Performance Characteristics Noise Voltage (Continued) Start-Up Response DS006685-31 DS006685-32 Typical Applications The LM34 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface and its temperature will be within about 0.02˚F of the surface temperature. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature of the LM34 die would be at an intermediate temperature between the surface temperature and the air temperature. This is expecially true for the TO-92 plastic package, where the copper leads are the principal thermal path to carry heat into the device, so its temperature might be closer to the air temperature than to the surface temperature. To minimize this problem, be sure that the wiring to the LM34, as it leaves the device, is held at the same temperature as the surface of interest. The easiest way to do this is to cover up these wires with a bead of epoxy which will insure that the leads and wires are all at the same temperature as the surface, and that the LM34 die’s temperature will not be affected by the air temperature. The TO-46 metal package can also be soldered to a metal surface or pipe without damage. Of course in that case, the V− terminal of the circuit will be grounded to that metal. Alternatively, the LM34 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM34 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to insure that moisture cannot corrode the LM34 or its connections. and speed up the response in slowly-moving air. On the other hand, a small thermal mass may be added to the sensor to give the steadiest reading despite small deviations in the air temperature. Capacitive Loads Like most micropower circuits, the LM34 has a limited ability to drive heavy capacitive loads. The LM34 by itself is able to drive 50 pF without special precautions. If heavier loads are anticipated, it is easy to isolate or decouple the load with a resistor; see Figure 3. Or you can improve the tolerance of capacitance with a series R-C damper from output to ground; see Figure 4. When the LM34 is applied with a 499Ω load resistor (as shown), it is relatively immune to wiring capacitance because the capacitance forms a bypass from ground to input, not on the output. However, as with any linear circuit connected to wires in a hostile environment, its performance can be affected adversely by intense electromagnetic sources such as relays, radio transmitters, motors with arcing brushes, SCR’s transients, etc., as its wiring can act as a receiving antenna and its internal junctions can act as rectifiers. For best results in such cases, a bypass capacitor from VIN to ground and a series R-C damper such as 75Ω in series with 0.2 or 1 µF from output to ground are often useful. These are shown in the following circuits. DS006685-6 These devices are sometimes soldered to a small, light-weight heat fin to decrease the thermal time constant www.national.com 6 Typical Applications DS006685-7 FIGURE 3. LM34 with Decoupling from Capacitive Load DS006685-8 FIGURE 4. LM34 with R-C Damper Temperature Rise of LM34 Due to Self-Heating (Thermal Resistance) Conditions TO-46, No Heat Sink Still air Moving air Still oil Stirred oil (Clamped to metal, infinite heat sink) Note 14: Wakefield type 201 or 1" disc of 0.020" sheet brass, soldered to case, or similar. Note 15: TO-92 and SO-8 packages glued and leads soldered to 1" square of 1/16" printed circuit board with 2 oz copper foil, or similar. TO-46, Small Heat Fin (Note 14) 180˚F/W 72˚F/W 72˚F/W 54˚F/W (43˚F/W) TO-92, No Heat Sink 324˚F/W 162˚F/W 162˚F/W 81˚F/W TO-92, Small Heat Fin (Note 15) 252˚F/W 126˚F/W 126˚F/W 72˚F/W SO-8 No Heat Sink 400˚F/W 190˚F/W SO-8 Small Heat Fin (Note 15) 200˚F/W 160˚F/W 720˚F/W 180˚F/W 180˚F/W 90˚F/W (95˚F/W) Two-Wire Remote Temperature Sensor (Grounded Sensor) Two-Wire Remote Temperature Sensor (Output Referred to Ground) DS006685-9 DS006685-10 VOUT = 10mV/˚F (TA+3˚F) FROM +3˚F TO + 100˚F 7 www.national.com Typical Applications (Continued) Fahrenheit Thermometer (Analog Meter) 4-to-20 mA Current Source (0 to +100˚F) DS006685-12 DS006685-11 Expanded Scale Thermometer (50˚ to 80˚ Fahrenheit, for Example Shown) Temperature-to-Digital Converter (Serial Output, +128˚F Full Scale) DS006685-14 DS006685-13 LM34 with Voltage-to-Frequency Converter and Isolated Output (3˚F to + 300˚F; 30 Hz to 3000 Hz) DS006685-15 www.national.com 8 Typical Applications (Continued) Bar-Graph Temperature Display (Dot Mode) DS006685-16 * = 1% or 2% film resistor — Trim RB for VB = 3.525V — Trim RC for VC = 2.725V — Trim RA for VA = 0.085V + 40 mV/˚F x TAMBIENT — Example, VA = 3.285V at 80˚F Temperature-to-Digital Converter (Parallel TRI-STATE ® Outputs for Standard Data Bus to µP Interface, 128 ˚F Full Scale) DS006685-17 9 www.national.com Typical Applications (Continued) Temperature Controller DS006685-18 Block Diagram DS006685-19 www.national.com 10 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM34H, LM34AH, LM34CH, LM34CAH or LM34DH NS Package H03H Order Number LM34DM NS Package Number M08A 11 www.national.com LM34 Precision Fahrenheit Temperature Sensors Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Order Number LM34CZ, LM34CAZ or LM34DZ NS Package Z03A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.