NTE5602

NTE5600 thru NTE5607 TRIAC, 4 Amp Description: The NTE5600 through NTE5607 TRIACs are designed primarily for full–wave AC control applications such as light dimmers, motor controls, heating controls and power supplies; or wherever full–wave silicon gate controlled solid–state devices are needed. TRIAC type thyristors switch from a blocking to a conducting state for either polarity of applied anode voltage with positive or negative gate triggering. Features: D 2 Mode Gate Triggering D Blocking Voltages to 600V D All Diffused and Glass Passivated Junctions for Greater Parameters Uniformity and Stability Absolute Maximum Ratings: Repetitive Peak Off–State Voltage (TC = +110°C, Note 1), VDRM NTE5600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V NTE5601 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50V NTE5602 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100V NTE5603 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200V NTE5604 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V NTE5605 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400V NTE5606 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500V NTE5607 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600V RMS On–State Current (TC = +85°C), IT(RMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A Peak Surge Current (One Full Cycle, 60Hz, TJ = –40° to +110°C), ITSM . . . . . . . . . . . . . . . . . . . 30A Circuit Fusing (t = 8.3ms), I2t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7A2s Peak Gate Power, PGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10W Average Gate Power, PG(AV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5W Peak Gate Voltage, VGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Operating Junction Temperature Range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40° to +110°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40° to +150°C Thermal Resistance, Junction–to–Case, RthJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5°C/W Thermal Resistance, Junction–to–Ambient, RthJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75°C/W Mounting Torque (6–32 Screw, Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 in. lb. Note 1. Ratings apply for open gate conditions. Thyristor devices shall not be tested with a constant current source for blocking capability such that the voltage applied exceeds the rated blocking voltage. Note 2. Torque rating applies with the use of a compression washer. Mounting torque in excess of 8 in. lb. does not appreciably lower case–to–sink thermal resistance. MT2 and heatsink contact pad are common. Electrical Characteristics: (TC = +25°C unless otherwise specified) Parameter Peak Forward or Reverse Blocking Current Symbol IDRM, IRRM On–State Voltage (Either Direction) VTM Peak Gate Trigger Voltage MT2 (+), G (+); MT2 (–), G (–) MT2 (+), G (–); MT2 (–), G (+) VGT Peak Gate Trigger Voltage MT2 (+), G (+); MT2 (–), G (–) MT2 (+), G (–); MT2 (–), G (+) VGT Holding Current (Either Direction) IH Turn–On Time (Either Direction) Blocking Voltage Application Rate at Commutation Gate Trigger Current Quads I & III ton dv/dt IGT Test Conditions Min Typ Max Unit Rated VDRM or VRRM, Gate Open, TJ = +25°C – – 10 µA Rated VDRM or VRRM, Gate Open, TJ = +110°C – – 2 mA ITM = 6A Peak – – 2 V Main Terminal Voltage = 12V, RL = 100Ω, TJ = –40°C – 1.4 2.5 V 0.2 – – V Main Terminal Voltage = 12V, Gate Open, TJ = –40°C, Initiating Current = 1A – – 70 mA Main Terminal Voltage = 12V, Gate Open, TJ = +25°C – – 30 mA ITM = 14A, IGT = 100mA – 1.5 – µs Rated VDRM, Gate Open, TJ = +85°C – 5 – V/µs Main Terminal Voltage = 12V, RL = 100Ω, TJ = +25°C – – 30 mA Main Terminal Voltage = 12V, RL = 100Ω, TJ = –40°C – – 60 mA Main Terminal Voltage = Rated VDRM, RL = 10kΩ, TJ = +110°C .330 (8.38) Max .175 (4.45) Max .450 (11.4) Max .118 (3.0) Dia .655 (16.6) Max .030 (.762) Dia MT1 MT2 G .090 (2.28) .130 (3.3) Max