74HC4060N

74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Rev. 03 — 14 July 2008 Product data sheet 1. General description The 74HC4060; 74HCT4060 are high-speed Si-gate CMOS device and is pin compatible with the HEF4060. The 74HC4060; 74HCT4060 are 14-stage ripple-carry counter/dividers and oscillators with three oscillator terminals (RS, RTC and CTC), ten buffered outputs (Q3 to Q9 and Q11 to Q13) and an overriding asynchronous master reset (MR). The oscillator configuration allows design of either RC or crystal oscillator circuits. The oscillator may be replaced by an external clock signal at input RS. In this case keep the other oscillator pins (RTC and CTC) floating. The counter advances on the negative-going transition of RS. A HIGH level on MR resets the counter (Q3 to Q9 and Q11 to Q13 = LOW), independent of other input conditions. In the HCT version, the MR input is TTL compatible, but the RS input has CMOS input switching levels and can be driven by a TTL output by using a pull-up resistor to VCC. 2. Features I I I I All active components on chip RC or crystal oscillator configuration Complies with JEDEC standard no. 7 A ESD protection: N HBM JESD22-A114E exceeds 2000 V N MM JESD22-A115-A exceeds 200 V I Multiple package options I Specified from −40 °C to +85 °C and from −40 °C to +125 °C 3. Applications I I I I Control counters Timers Frequency dividers Time-delay circuits NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 4. Ordering information Table 1. Ordering information Package Temperature range Name 74HC4060N 74HCT4060N 74HC4060D 74HCT4060D 74HC4060DB 74HCT4060DB 74HC4060PW 74HC4060BQ 74HCT4060BQ −40 °C to +125 °C −40 °C to +125 °C TSSOP16 −40 °C to +125 °C SSOP16 −40 °C to +125 °C SO16 plastic small outline package; 16 leads; body width 3.9 mm plastic shrink small outline package; 16 leads; body width 5.3 mm SOT109-1 SOT338-1 −40 °C to +125 °C DIP16 Description plastic dual in-line package; 16 leads (300 mil) Version SOT38-4 Type number plastic thin shrink small outline package; 16 leads; SOT403-1 body width 4.4 mm DHVQFN16 plastic dual in-line compatible thermal-enhanced SOT763-1 very thin quad flat package; no leads; 16 terminals; body 2.5 × 3.5 × 0.85 mm 5. Functional diagram 10 9 RTC CTC 11 12 RS MR Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q11 Q12 Q13 7 5 4 6 14 13 15 1 2 3 001aai467 Fig 1. Logic symbol 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 2 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator CTR14 !G 9 10 11 12 CT = 0 CX RX RCX CT 9 11 13 (a) + 3 7 5 4 6 14 13 15 1 2 3 11 12 CTR14 3 7 5 4 AND + CT CT = 0 9 11 13 (b) 001aai468 6 14 13 15 1 2 3 Fig 2. IEC logic symbol 10 RTC 11 RS 9 CTC CP MR 14-STAGE BINARY COUNTER Q4 5 4 Q5 6 Q6 Q7 14 Q8 13 Q9 15 1 Q11 Q12 Q13 2 3 001aai113 12 MR Q3 7 Fig 3. Functional diagram CTC RTC RS FF 1 CP Q MR MR FF 4 CP Q MR FF 10 CP Q MR FF 12 CP Q MR FF 14 CP Q MR Q3 Q9 Q11 Q13 001aai114 Fig 4. Logic diagram 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 3 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 6. Pinning information 6.1 Pinning 74HC4060 74HCT4060 Q11 Q12 Q13 Q5 Q4 Q6 Q3 GND 1 2 3 4 5 6 7 8 001aai115 74HC4060 74HCT4060 16 VCC 15 Q9 Q12 14 Q7 13 Q8 12 MR 11 RS 10 RTC 9 CTC Q13 Q5 Q4 Q6 Q3 2 3 4 5 6 7 8 GND CTC 9 VCC (1) terminal 1 index area 16 VCC 15 Q9 14 Q7 13 Q8 12 MR 11 RS 10 RTC 1 Q11 001aai469 Transparent top view (1) The die substrate is attached to this pad using conductive die attach material. It cannot be used as supply pin or input. Fig 5. Pin configuration DIP16, SO16 and (T)SSOP16 Fig 6. Pin configuration DHVQFN16 6.2 Pin description Table 2. Symbol Q11 to Q13 Q3 to Q9 GND CTC RTC RS MR VCC Pin description Pin 1, 2, 3 7, 5, 4, 6, 14, 13, 15 8 9 10 11 12 16 Description counter output counter output ground (0 V) external capacitor connection external resistor connection clock input /oscillator pin master reset input (active HIGH) supply voltage 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 4 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 7. Functional description 1 RS 2 4 8 16 32 64 128 256 512 1024 2048 4096 8192 16384 MR Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q11 Q12 Q13 001aai117 Fig 7. Timing diagram 8. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC IIK IOK IO ICC IGND Tstg Parameter supply voltage input clamping current output clamping current output current supply current ground current storage temperature VI < −0.5 V or VI > VCC + 0.5 V VO < −0.5 V or VO > VCC + 0.5 V −0.5 V < VO < VCC + 0.5 V [1] [1] Conditions Min −0.5 −50 −65 Max +7 ±20 ±20 ±25 50 +150 Unit V mA mA mA mA mA °C 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 5 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Table 3. Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Ptot Parameter total power dissipation Conditions Tamb = −40 °C to +125 °C DIP16 package SO16 package (T)SSOP16 package DHVQFN16 package [1] [2] [3] [4] [5] [2] [3] [4] [5] Min - Max 750 500 500 500 Unit mW mW mW mW The input and output voltage ratings may be exceeded if the input and output current ratings are observed. Ptot derates linearly with 12 mW/K above 70 °C. Ptot derates linearly with 8 mW/K above 70 °C. Ptot derates linearly with 5.5 mW/K above 60 °C. Ptot derates linearly with 4.5 mW/K above 60 °C. 9. Recommended operating conditions Table 4. Recommended operating conditions Voltages are referenced to GND (ground = 0 V) Symbol Parameter VCC VI VO Tamb ∆t/∆V supply voltage input voltage output voltage ambient temperature input transition rise and fall rate VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V Conditions Min 2.0 0 0 −40 74HC4060 Typ 5.0 1.67 Max 6.0 VCC VCC +125 625 139 83 Min 4.5 0 0 −40 74HCT4060 Typ 5.0 1.67 Max 5.5 VCC VCC +125 139 V V V °C ns/V ns/V ns/V Unit 10. Static characteristics Table 5. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter 74HC4060 VIH HIGH-level input voltage MR input VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V RS input VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V 1.7 3.6 4.8 1.7 3.6 4.8 1.7 3.6 4.8 V V V 1.5 3.15 4.2 1.3 2.4 3.1 1.5 3.15 4.2 1.5 3.15 4.2 V V V Conditions Min 25 °C Typ Max −40 °C to +85 °C −40 °C to +125 °C Unit Min Max Min Max 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 6 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Table 5. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VIL LOW-level input voltage Conditions Min MR input VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V RS input VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VOH HIGH-level output voltage RTC output; RS = MR = GND IO = −20 µA; VCC = 2.0 V IO = −20 µA; VCC = 4.5 V IO = −20 µA; VCC = 6.0 V IO = −2.6 mA; VCC = 4.5 V IO = −3.3 mA; VCC = 6.0 V RTC output; RS = MR = VCC IO = −20 µA; VCC = 2.0 V IO = −20 µA; VCC = 4.5 V IO = −20 µA; VCC = 6.0 V IO = −0.65 mA; VCC = 4.5 V IO = −0.85 mA; VCC = 6.0 V CTC output; RS = VIH; MR = VIL IO = −3.2 mA; VCC = 4.5 V IO = −4.2 mA; VCC = 6.0 V VI = VIH or VIL; except RTC output IO = −20 µA; VCC = 2.0 V IO = −20 µA; VCC = 4.5 V IO = −20 µA; VCC = 6.0 V VI = VIH or VIL; except RTC and CTC outputs IO = −4.0 mA; VCC = 4.5 V IO = −5.2 mA; VCC = 6.0 V 3.98 5.48 3.84 5.34 3.7 5.2 V V 1.9 4.4 5.9 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 V V V 3.98 5.48 3.84 5.34 3.7 5.2 V V 1.9 4.4 5.9 3.98 5.48 2.0 4.5 6.0 1.9 4.4 5.9 3.84 5.34 1.9 4.4 5.9 3.7 5.2 V V V V V 1.9 4.4 5.9 3.98 5.48 2.0 4.5 6.0 1.9 4.4 5.9 3.84 5.34 1.9 4.4 5.9 3.7 5.2 V V V V V 0.3 0.9 1.2 0.3 0.9 1.2 0.3 0.9 1.2 V V V 0.8 2.1 2.8 0.5 1.35 1.8 0.5 1.35 1.8 0.5 1.35 1.8 V V V 25 °C Typ Max −40 °C to +85 °C −40 °C to +125 °C Unit Min Max Min Max 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 7 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Table 5. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VOL LOW-level output voltage Conditions Min RTC output; RS = VCC; MR = GND IO = 20 µA; VCC = 2.0 V IO = 20 µA; VCC = 4.5 V IO = 20 µA; VCC = 6.0 V IO = 2.6 mA; VCC = 4.5 V IO = 3.3 mA; VCC = 6.0 V CTC output; RS = VIL; MR = VIH IO = 3.2 mA; VCC = 4.5 V IO = 4.2 mA; VCC = 6.0 V VI = VIH or VIL; except RTC output IO = 20 µA; VCC = 2.0 V IO = 20 µA; VCC = 4.5 V IO = 20 µA; VCC = 6.0 V VI = VIH or VIL; except RTC and CTC outputs IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6.0 V II ICC CI input leakage VI = VCC or GND; VCC = 6.0 V current supply current input capacitance HIGH-level input voltage LOW-level input voltage MR input; VCC = 4.5 V to 5.5 V MR input; VCC = 4.5 V to 5.5 V [1] 25 °C Typ Max −40 °C to +85 °C −40 °C to +125 °C Unit Min Max Min Max - 0 0 0 - 0.1 0.1 0.1 0.26 0.26 - 0.1 0.1 0.1 0.33 0.33 - 0.1 0.1 0.1 0.4 0.4 V V V V V - - 0.26 0.26 - 0.33 0.33 - 0.4 0.4 V V - 0 0 0 0.1 0.1 0.1 - 0.1 0.1 0.1 - 0.1 0.1 0.1 V V V - 3.5 0.26 0.26 ±0.1 8.0 - - 0.33 0.33 ±1.0 80 - - 0.4 0.4 ±1.0 160 - V V µA µA pF VI = VCC or GND; IO = 0 A; VCC = 6.0 V 74HCT4060 VIH VIL 2.0 0.8 2.0 0.8 2.0 0.8 V V [1] 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 8 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Table 5. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VOH HIGH-level output voltage Conditions Min RTC output; RS = MR = VCC IO = −20 µA; VCC = 4.5 V IO = −0.65 mA; VCC = 4.5 V RTC output; RS = MR = GND IO = −20 µA; VCC = 4.5 V IO = −2.6 mA; VCC = 4.5 V CTC output; RS = VIH; MR = VIL IO = −3.2 mA; VCC = 4.5 V VI = VIH or VIL; except RTC output IO = −20 µA; VCC = 4.5 V VI = VIH or VIL; except RTC and CTC outputs IO = −4.0 mA; VCC = 4.5 V VOL LOW-level output voltage RTC output; RS = VCC; MR = GND IO = 20 µA; VCC = 4.5 V IO = 2.6 mA; VCC = 4.5 V CTC output; RS = VIL; MR = VIH IO = 3.2 mA; VCC = 4.5 V VI = VIH or VIL; except RTC output IO = 20 µA; VCC = 4.5 V VI = VIH or VIL; except RTC and CTC outputs IO = 4.0 mA; VCC = 4.5 V II ICC ∆ICC input leakage VI = VCC or GND; VCC = 5.5 V current supply current additional supply current input capacitance VI = VCC or GND; VCC = 5.5 V; IO = 0 A per input pin; VI = VCC − 2.1 V; other inputs at VCC or GND; VCC = 4.5 V to 5.5 V; IO = 0 A 40 0.26 ±0.1 8.0 144 0.33 ±1.0 80 180 0.4 ±1.0 160 196 V µA µA µA 0 0.1 0.1 0.1 V 0.26 0.33 0.4 V 0 0.1 0.26 0.1 0.33 0.1 0.4 V V 3.98 3.84 3.7 V 4.4 4.5 4.4 4.4 V 3.98 3.84 3.7 V 4.4 3.98 4.5 4.4 3.84 4.4 3.7 V V 4.4 3.98 4.5 4.4 3.84 4.4 3.7 V V 25 °C Typ Max −40 °C to +85 °C −40 °C to +125 °C Unit Min Max Min Max CI - 3.5 - - - - - pF [1] For HCT4060, only input MR (pin 12) has TTL input switching levels. 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 9 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 11. Dynamic characteristics Table 6. Dynamic characteristics GND = 0 V; CL = 50 pF unless otherwise specified; for test circuit see Figure 11. Symbol Parameter 74HC4060 tpd propagation delay RS to Q3; see Figure 8 VCC = 2.0 V VCC = 4.5 V VCC = 5.0 V; CL = 15 pF VCC = 6.0 V Qn to Qn+1; see Figure 9 VCC = 2.0 V VCC = 4.5 V VCC = 5.0 V; CL = 15 pF VCC = 6.0 V tPHL HIGH to LOW MR to Qn; see Figure 10 propagation VCC = 2.0 V delay VCC = 4.5 V VCC = 5.0 V; CL = 15 pF VCC = 6.0 V tt transition time Qn; see Figure 8 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V tW pulse width RS (HIGH or LOW); see Figure 8 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V MR (HIGH); see Figure 10 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V trec recovery time MR to RS; see Figure 10 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V 100 20 17 28 10 8 125 25 21 150 30 26 ns ns ns 80 16 14 25 9 7 100 20 17 120 24 20 ns ns ns 80 16 14 17 6 5 100 20 17 120 24 20 ns ns ns [3] [2] [1] Conditions Min 25 °C Typ Max −40 °C to +85 °C −40 °C to +125 °C Unit Min Max Min Max - 99 36 31 29 22 8 6 6 55 20 17 16 19 7 6 300 60 51 80 16 14 175 35 30 75 15 13 - 375 75 64 100 20 17 220 44 37 95 19 16 - 450 90 77 120 24 20 265 53 45 110 22 19 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 10 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Table 6. Dynamic characteristics …continued GND = 0 V; CL = 50 pF unless otherwise specified; for test circuit see Figure 11. Symbol Parameter fmax maximum frequency Conditions Min RS; see Figure 8 VCC = 2.0 V VCC = 4.5 V VCC = 5.0 V; CL = 15 pF VCC = 6.0 V CPD power dissipation capacitance propagation delay VI = GND to VCC; VCC = 5 V; fi = 1 MHz [4] 25 °C Typ 26 80 87 95 40 Max - −40 °C to +85 °C −40 °C to +125 °C Unit Min 4.8 24 28 Max Min 4 20 24 Max MHz MHz MHz MHz pF 6 30 35 - 74HCT4060 tpd RS to Q3; see Figure 8 VCC = 4.5 V VCC = 5.0 V; CL = 15 pF Qn to Qn+1; see Figure 9 VCC = 4.5 V VCC = 5.0 V; CL = 15 pF tPHL HIGH to LOW MR to Qn; see Figure 10 propagation VCC = 4.5 V delay VCC = 5.0 V; CL = 15 pF tt tW transition time Qn; see Figure 8 VCC = 4.5 V pulse width RS (HIGH or LOW); see Figure 8 VCC = 4.5 V MR (HIGH); see Figure 10 VCC = 4.5 V trec fmax recovery time maximum frequency MR to RS; see Figure 10 VCC = 4.5 V RS; see Figure 8 VCC = 4.5 V VCC = 5.0 V; CL = 15 pF 30 80 88 24 20 MHz MHz 26 13 33 39 ns 16 6 20 24 ns 16 6 20 24 ns [3] [2] [1] - 33 31 8 6 21 18 7 66 16 44 15 - 83 20 55 19 - 99 24 66 22 ns ns ns ns ns ns ns 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 11 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator Table 6. Dynamic characteristics …continued GND = 0 V; CL = 50 pF unless otherwise specified; for test circuit see Figure 11. Symbol Parameter CPD power dissipation capacitance Conditions Min VI = GND to VCC − 1.5 V; VCC = 5 V; fi = 1 MHz [4] 25 °C Typ 40 Max - −40 °C to +85 °C −40 °C to +125 °C Unit Min Max Min Max pF [1] [2] [3] [4] tpd is the same as tPHL and tPLH. Qn+1 is the next Qn output. tt is the same as tTHL and tTLH. CPD is used to determine the dynamic power dissipation (PD in µW): PD = CPD × VCC2 × fi × N + ∑(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; ∑(CL × VCC2 × fo) = sum of outputs. 12. Waveforms 1/fmax VI RS input GND tW tPHL VOH Q3 output VOL 90 % VM 10 % tTHL 10 % tTLH 001aai118 tPLH 90 % VM Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Fig 8. Waveforms showing the clock (RS) to output (Q3) propagation delays, the clock pulse width, the output transition times and the maximum clock frequency 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 12 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator VOH Qn output VOL tPLH VOH Qn+1 output VOL VM 001aai120 VM tPHL Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Fig 9. Waveforms showing the output Qn to output Qn+1 propagation delays VI MR input GND TW VI RS input GND tPHL VOH Qn output VOL VM 001aai119 VM trec VM Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Fig 10. Waveforms showing the master reset (MR) pulse width, the master reset to output (Qn) propagation delays and the master reset to clock (RS) recovery time Table 7. Type 74HC4060 74HCT4060 Measurement points Input VM 0.5 × VCC 1.3 V Output VM 0.5 × VCC 1.3 V 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 13 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator VI negative pulse GND tW 90 % VM 10 % tf tr tr tf 90 % VM 10 % tW VCC G VI VO VM VI positive pulse GND VM DUT RT CL 001aah768 Test data is given in Table 8. Definitions test circuit: RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. Fig 11. Test circuit for measuring switching times Table 8. Type 74HC4060 74HCT4060 Test data Input VI VCC 3V tr, tf 6 ns 6 ns Load CL 15 pF, 50 pF 15 pF, 50 pF 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 14 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 13. RC oscillator 13.1 Timing component limitations The oscillator frequency is mainly determined by RtCt, provided R2 ≈ 2Rt and R2C2 50 pF, up to any practical value and 10 kΩ < Rt < 1 MΩ. In order to avoid start-up problems, Rt ≥ 1 kΩ. 13.2 Typical crystal oscillator circuit In Figure 13, R2 is the power limiting resistor. For starting and maintaining oscillation a minimum transconductance is necessary, so R2 should not be too large. A practical value for R2 is 2.2 kΩ. 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 15 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator MR (from logic) 11 RS 74HC4060 74HCT4060 Rbias 560 kΩ VDD RTC 10 0.47 pF 100 µF Rbias 100 kΩ to 1MΩ VI (fi = 1 kHz) R2 2.2 kΩ input output A IO GND 001aai123 gfs = ∆IO / ∆VI at VO is constant; MR = LOW. C3 22 pF to 37 pF C2 100 pF See also Figure 15. 001aai122 Fig 13. External component connection for a crystal oscillator Fig 14. Test set-up for measuring forward transconductance 14 (1) 001aai124 gfs (mA/V) 10 (2) (3) 6 2 0 2 4 VCC (V) 6 Tamb = 25 °C. (1) Maximum. (2) Typical. (3) Minimum. Fig 15. Typical forward transconductance as function of the supply voltage 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 16 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 105 fosc (Hz) 104 Rt 001aai125 105 fosc (Hz) 104 Ct 001aai127 103 103 102 102 10 103 104 105 Rt (Ω) 106 10 10−4 10−3 10−2 Ct (µF) 10−1 VCC = 2.0 V to 6.0 V; Tamb = 25 °C. For Rt curve: Ct = 1 nF; R2 = 2 × Rt. VCC = 2.0 V to 6.0 V; Tamb = 25 °C. For Ct curve: Rt = 100 kΩ; R2 = 200 kΩ. Fig 16. RC oscillator frequency as a function of Rt Fig 17. RC oscillator frequency as a function of Ct 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 17 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 14. Package outline DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4 D seating plane ME A2 A L A1 c Z e b1 b 16 9 b2 MH wM (e 1) pin 1 index E 1 8 0 5 scale 10 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.02 A2 max. 3.2 0.13 b 1.73 1.30 0.068 0.051 b1 0.53 0.38 0.021 0.015 b2 1.25 0.85 0.049 0.033 c 0.36 0.23 0.014 0.009 D (1) 19.50 18.55 0.77 0.73 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.1 e1 7.62 0.3 L 3.60 3.05 0.14 0.12 ME 8.25 7.80 0.32 0.31 MH 10.0 8.3 0.39 0.33 w 0.254 0.01 Z (1) max. 0.76 0.03 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT38-4 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 95-01-14 03-02-13 Fig 18. Package outline SOT38-4 (DIP16) 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 18 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index θ Lp 1 e bp 8 wM L detail X A1 (A 3) A 0 2.5 scale 5 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07 JEDEC MS-012 JEITA EUROPEAN PROJECTION A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3 θ 0.010 0.057 0.069 0.004 0.049 0.019 0.0100 0.39 0.014 0.0075 0.38 0.244 0.041 0.228 0.028 0.004 0.012 8 o 0 o ISSUE DATE 99-12-27 03-02-19 Fig 19. Package outline SOT109-1 (SO16) 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 19 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 D E A X c y HE vM A Z 16 9 Q A2 A1 pin 1 index Lp L 1 bp 8 wM detail X (A 3) θ A e 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 2 A1 0.21 0.05 A2 1.80 1.65 A3 0.25 bp 0.38 0.25 c 0.20 0.09 D (1) 6.4 6.0 E (1) 5.4 5.2 e 0.65 HE 7.9 7.6 L 1.25 Lp 1.03 0.63 Q 0.9 0.7 v 0.2 w 0.13 y 0.1 Z (1) 1.00 0.55 θ 8 o 0 o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT338-1 REFERENCES IEC JEDEC MO-150 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 20. Package outline SOT338-1 (SSOP16) 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 20 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index A1 θ Lp L (A 3) A 1 e bp 8 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.40 0.06 θ 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 21. Package outline SOT403-1 (TSSOP16) 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 21 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; SOT763-1 16 terminals; body 2.5 x 3.5 x 0.85 mm D B A A A1 E c terminal 1 index area detail X terminal 1 index area e 2 L e1 b 7 vMCAB wM C y1 C C y 1 Eh 16 8 e 9 15 Dh 10 X 2.5 scale 5 mm 0 DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. 1 A1 0.05 0.00 b 0.30 0.18 c 0.2 D (1) 3.6 3.4 Dh 2.15 1.85 E (1) 2.6 2.4 Eh 1.15 0.85 e 0.5 e1 2.5 L 0.5 0.3 v 0.1 w 0.05 y 0.05 y1 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. OUTLINE VERSION SOT763-1 REFERENCES IEC --JEDEC MO-241 JEITA --EUROPEAN PROJECTION ISSUE DATE 02-10-17 03-01-27 Fig 22. Package outline SOT763-1 (DHVQFN16) 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 22 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 15. Abbreviations Table 9. Acronym CMOS DUT ESD HBM MM TTL Abbreviations Description Complementary Metal-Oxide Semiconductor Device Under Test ElectroStatic Discharge Human Body Model Machine Model Transistor-Transistor Logic 16. Revision history Table 10. Revision history Release date 20080714 Data sheet status Product data sheet Change notice Supersedes 74HC_HCT4060_CNV_2 Document ID 74HC_HCT4060_3 Modifications: • • • • • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Section 4: DHVQFN16 package added. Section 8: derating values added for DHVQFN16 package. Section 14: outline drawing added for DHVQFN16 package. Product specification - 74HC_HCT4060_CNV_2 19970901 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 23 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 17. Legal information 18. Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term ‘short data sheet’ is explained in section “Definitions”. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.1 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 18.2 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or 18.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com 74HC_HCT4060_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 14 July 2008 24 of 25 NXP Semiconductors 74HC4060; 74HCT4060 14-stage binary ripple counter with oscillator 20. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 12 13 13.1 13.2 14 15 16 17 18 18.1 18.2 18.3 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recommended operating conditions. . . . . . . . 6 Static characteristics. . . . . . . . . . . . . . . . . . . . . 6 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 RC oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Timing component limitations . . . . . . . . . . . . . 15 Typical crystal oscillator circuit . . . . . . . . . . . . 15 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 23 Legal information. . . . . . . . . . . . . . . . . . . . . . . 24 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 24 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Contact information. . . . . . . . . . . . . . . . . . . . . 24 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 14 July 2008 Document identifier: 74HC_HCT4060_3