74HCT9046AD

74HCT9046A PLL with band gap controlled VCO Rev. 06 — 15 September 2009 Product data sheet 1. General description The 74HCT9046A is a high-speed Si-gate CMOS device. It is specified in compliance with JEDEC standard no 7A. 2. Features I I I I I Operation power supply voltage range from 4.5 V to 5.5 V Low power consumption Inhibit control for ON/OFF keying and for low standby power consumption center frequency up to 17 MHz (typical) at VCC = 5.5 V Choice of two phase comparators: N PC1: EXCLUSIVE-OR N PC2: Edge-triggered JK flip-flop No dead zone of PC2 Charge pump output on PC2, whose current is set by an external resistor Rbias center frequency tolerance ±10 % Excellent Voltage Controlled Oscillator (VCO) linearity Low frequency drift with supply voltage and temperature variations On-chip band gap reference Glitch free operation of VCO, even at very low frequencies Zero voltage offset due to operational amplifier buffering ESD protection: N HBM JESD22-A114F exceeds 2000 V N MM JESD22-A115-A exceeds 200 V I I I I I I I I I NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 3. Applications I FM modulation and demodulation where a small center frequency tolerance is essential I Frequency synthesis and multiplication where a low jitter is required (e.g. video picture-in-picture) I Frequency discrimination I Tone decoding I Data synchronization and conditioning I Voltage-to-frequency conversion I Motor-speed control 4. Ordering information Table 1. Ordering information Package Temperature range Name 74HCT9046AN 74HCT9046AD 74HCT9046APW −40 °C to +125 °C −40 °C to +125 °C −40 °C to +125 °C DIP16 SO16 TSSOP16 Description plastic dual in-line package; 16 leads (300 mil) plastic small outline package; 16 leads; body width 3.9 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm Version SOT38-4 SOT109-1 SOT403-1 Type number 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 2 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 5. Block diagram fout C1 fin C1A 6 C1B 7 VCO_OUT COMP_IN SIG_IN 4 3 14 VCC 16 9046A R2 12 PHASE COMPARATOR 1 PC1_OUT/ 2 PCP_OUT R3 R2 VCO R1 11 R1 PHASE COMPARATOR 2 13 PC2_OUT 15 RB Rbias R4 C2 5 INH 10 9 8 GND 1 GND mbd040 DEM_OUT VCO_IN Rs Fig 1. Block diagram 6. Functional diagram 3 14 15 COMP_IN SIG_IN RB PC1_OUT/ PCP_OUT 2 Φ PC2_OUT Φ PLL 9046A 3 14 6 COMP_IN SIG_IN C1A C1B R1 R2 RB VCO_IN INH mbd039 13 PC1_OUT/ PCP_OUT PC2_OUT 2 13 6 7 11 12 9 5 C1A C1B R1 R2 VCO_IN INH mbd038 7 VCO_OUT 4 11 12 15 VCO DEM_OUT DEM_OUT VCO_OUT 10 4 10 9 5 Fig 2. Logic symbol Fig 3. IEC logic symbol 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 3 of 43 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data sheet Rev. 06 — 15 September 2009 4 of 43 74HCT9046A_6 NXP Semiconductors C1 fout 7 4 COMP_IN 3 fin 14 SIG_IN PC1 6 C1A C1B VCO_OUT Vref2 12 R2 PC1_OUT/ PCP_OUT 2 R2 VCO R3 Vref1 11 R1 logic 1 D CP Q up PCP R1 Q RD logic 1 10 DEM_OUT RS D CP Q down CHARGE PUMP PC2_OUT 13 (1) R3' R4 C2 Vref1 Vref2 Q RD RB 15 Rbias BAND GAP Vref2 VCO_IN 9 INH 5 PLL with band gap controlled VCO (1) R3' = Rbias /17 mbd102 Fig 4. Logic diagram 74HCT9046A © NXP B.V. 2009. All rights reserved. NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 7. Pinning information 7.1 Pinning 74HCT9046A GND PC1_OUT/ PCP_OUT COMP_IN VCO_OUT INH C1A C1B GND 1 2 3 4 5 6 7 8 001aae500 16 VCC 15 RB 14 SIG_IN 13 PC2_OUT 12 R2 11 R1 10 DEM_OUT 9 VCO_IN Fig 5. Pin configuration 7.2 Pin description Table 2. Symbol GND PC1_OUT/PCP_OUT COMP_IN VCO_OUT INH C1A C1B GND VCO_IN DEM_OUT R1 R2 PC2_OUT SIG_IN RB VCC Pin description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description ground (0 V) of phase comparators phase comparator 1 output or phase comparator pulse output comparator input VCO output inhibit input capacitor C1 connection A capacitor C1 connection B ground (0 V) VCO VCO input demodulator output resistor R1 connection resistor R2 connection phase comparator 2 output; current source adjustable with Rbias signal input bias resistor (Rbias) connection supply voltage 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 5 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 8. Functional description The 74HCT9046A is a phase-locked-loop circuit that comprises a linear VCO and two different phase comparators (PC1 and PC2) with a common signal input amplifier and a common comparator input, see Figure 1. The signal input can be directly coupled to large voltage signals (CMOS level), or indirectly coupled (with a series capacitor) to small voltage signals. A self-bias input circuit keeps small voltage signals within the linear region of the input amplifiers. With a passive low-pass filter, the 74HCT9046A forms a second-order loop PLL. The principle of this phase-locked-loop is based on the familiar 74HCT4046A. However extra features are built-in, allowing very high-performance phase-locked-loop applications. This is done, at the expense of PC3, which is skipped in this 74HCT9046A. The PC2 is equipped with a current source output stage here. Further a band gap is applied for all internal references, allowing a small center frequency tolerance. The details are summed up in Section 8.1. If one is familiar with the 74HCT4046A already, it will do to read this section only. 8.1 Differences with respect to the familiar 74HCT4046A • A center frequency tolerance of maximum ±10 %. • The on board band gap sets the internal references resulting in a minimal frequency shift at supply voltage variations and temperature variations. • The value of the frequency offset is determined by an internal reference voltage of 2.5 V instead of VCC − 0.7 V; In this way the offset frequency will not shift over the supply voltage range. • A current switch charge pump output on pin PC2_OUT allows a virtually ideal performance of PC2; The gain of PC2 is independent of the voltage across the low-pass filter; Further a passive low-pass filter in the loop achieves an active performance. The influence of the parasitic capacitance of the PC2 output plays no role here, resulting in a true correspondence of the output correction pulse and the phase difference even up to phase differences as small as a few nanoseconds. • Because of its linear performance without dead zone, higher impedance values for the filter, hence lower C-values, can be chosen; correct operation will not be influenced by parasitic capacitances as in case of the voltage source output using the 74HCT4046A. • No PC3 on pin RB but instead a resistor connected to GND, which sets the load/unload currents of the charge pump (PC2). • Extra GND pin 1 to allow an excellent FM demodulator performance even at 10 MHz and higher. • Combined function of pin PC1_OUT/PCP_OUT. If pin RB is connected to VCC (no bias resistor Rbias) pin PC1_OUT/PCP_OUT has its familiar function viz. output of PC1. If at pin RB a resistor (Rbias) is connected to GND it is assumed that PC2 has been chosen as phase comparator. Connection of Rbias is sensed by internal circuitry and this changes the function of pin PC1_OUT/PCP_OUT into a lock detect output (PCP_OUT) with the same characteristics as PCP_OUT of pin 1 of the 74HCT4046A. 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 6 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO • The inhibit function differs. For the 74HCT4046A a HIGH-level at the inhibit input (pin INH) disables the VCO and demodulator, while a LOW-level turns both on. For the 74HCT9046A a HIGH-level on the inhibit input disables the whole circuit to minimize standby power consumption. 8.2 VCO The VCO requires one external capacitor C1 (between pins C1A and C1B) and one external resistor R1 (between pins R1 and GND) or two external resistors R1 and R2 (between pins R1 and GND, and R2 and GND). Resistor R1 and capacitor C1 determine the frequency range of the VCO. Resistor R2 enables the VCO to have a frequency offset if required (see Figure 4). The high input impedance of the VCO simplifies the design of the low-pass filters by giving the designer a wide choice of resistor/capacitor ranges. In order not to load the low-pass filter, a demodulator output of the VCO input voltage is provided at pin DEM_OUT. The DEM_OUT voltage equals that of the VCO input. If DEM_OUT is used, a series resistor (Rs) should be connected from pin DEM_OUT to GND; if unused, DEM_OUT should be left open. The VCO output (pin VCO_OUT) can be connected directly to the comparator input (pin COMP_IN), or connected via a frequency divider. The output signal has a duty cycle of 50 % (maximum expected deviation 1 %), if the VCO input is held at a constant DC level. A LOW-level at the inhibit input (pin INH) enables the VCO and demodulator, while a HIGH-level turns both off to minimize standby power consumption. 8.3 Phase comparators The signal input (pin SIG_IN) can be directly coupled to the self-biasing amplifier at pin SIG_IN, provided that the signal swing is between the standard HC family input logic levels. Capacitive coupling is required for signals with smaller swings. 8.3.1 Phase Comparator 1 (PC1) This circuit is an EXCLUSIVE-OR network. The signal and comparator input frequencies (fi) must have a 50 % duty cycle to obtain the maximum locking range. The transfer characteristic of PC1, assuming ripple (fr = 2fi) is suppressed, is: V CC V DEM _ OUT = ---------- ( Φ SIG _ IN – Φ COMP_IN ) π where: VDEM_OUT is the demodulator output at pin DEM_OUT VDEM_OUT = VPC1_OUT (via low-pass) V CC The phase comparator gain is: K p = ---------- ( V ⁄ r ) π The average output voltage from PC1, fed to the VCO input via the low-pass filter and seen at the demodulator output at pin DEM_OUT (VDEM_OUT), is the resultant of the phase differences of signals (SIG_IN) and the comparator input (COMP_IN) as shown in Figure 6. The average of VDEM_OUT is equal to 0.5VCC when there is no signal or noise at SIG_IN and with this input the VCO oscillates at the center frequency (f0). Typical 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 7 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO waveforms for the PC1 loop locked at f0 are shown in Figure 7. This figure also shows the actual waveforms across the VCO capacitor at pins C1A and C1B (VC1A and VC1B) to show the relation between these ramps and the VCO_OUT voltage. The frequency capture range (2f0) is defined as the frequency range of input signals on which the PLL will lock if it was initially out-of-lock. The frequency lock range (2fL) is defined as the frequency range of the input signals on which the loop will stay locked if it was initially in lock. The capture range is smaller or equal to the lock range. With PC1, the capture range depends on the low-pass filter characteristics and can be made as large as the lock range. This configuration remains locked even with very noisy input signals. Typical behavior of this type of phase comparator is that it may lock to input frequencies close to the harmonics of the VCO center frequency. VCC VDEM_OUT(AV) mbd101 0.5VCC 0 0o 90 o ΦPC_IN 180 o V CC V DEM _ OUT = V PCI _ OUT = ---------- Φ SIG _ IN – Φ COMP _ IN π Φ PC _ IN = ( Φ SIG _ IN – Φ COMP _ IN ) Fig 6. Phase comparator 1; average output voltage as a function of input phase difference 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 8 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO SIGN_IN COMP_IN VCO_OUT PC1_OUT VCC VCO_IN GND VC1A C1A VC1B C1B mbd100 Fig 7. Typical waveforms for PLL using phase comparator 1; loop-locked at f0 8.3.2 Phase Comparator 2 (PC2) This is a positive edge-triggered phase and frequency detector. When the PLL is using this comparator, the loop is controlled by positive signal transitions and the duty cycles of SIG_IN and COMP_IN are not important. PC2 comprises two D-type flip-flops, control gating and a 3-state output stage with sink and source transistors acting as current sources, henceforth called charge pump output of PC2. The circuit functions as an up-down counter (see Figure 4) where SIG_IN causes an up-count and COMP_IN a down count. The current switch charge pump output allows a virtually ideal performance of PC2, due to appliance of some pulse overlap of the up and down signals, see Figure 8a. The pump current Icp is independent from the supply voltage and is set by the internal band gap reference of 2.5 V. 2.5 I cp = 17 × ----------- ( A ) R bias Where Rbias is the external bias resistor between pin RB and ground. The current and voltage transfer function of PC2 are shown in Figure 9. The phase comparator gain is: I cp K P = --------- ( A ⁄ r ) 2π 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 9 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO V up CC Icp PC2_OUT Icp C2 VCC up R3' Icp down PC2_OUT VC2_OUT C2 ∆ Φ = ΦPC_IN pulse overlap of approximately 15 ns mbd046 down mbd099 a. At every ∆Φ, even at zero ∆Φ both switches are closed simultaneously for a short period (typically 15 ns). Fig 8. The current switch charge pump output of PC2 b. Comparable voltage-controlled switch +Icp VCC VDEM_OUT(AV) 0 0.5VCC Icp × R −Icp −2π 0 ΦPC_IN +2π 0 −2π 0 001aak442 ΦPC_IN +2π 001aak443 a. Current transfer b. Voltage transfer. This transfer can be observed at PC2_OUT by connecting a resistor (R = 10 kΩ) between PC2_OUT and 0.5VCC. 5 V DEM _ OUT = V PC2 _ OUT = ----- Φ PC _ IN 4π Φ PC _ IN = ( Φ SIG _ IN – Φ COMP _ IN ) I cp pump c urrent --------- Φ PC _ IN 2π Fig 9. Phase comparator 2 current and voltage transfer characteristics When the frequencies of SIG_IN and COMP_IN are equal but the phase of SIG_IN leads that of COMP_IN, the up output driver at PC2_OUT is held ‘ON’ for a time corresponding to the phase difference (ΦPC_IN). When the phase of SIG_IN lags that of COMP_IN, the down or sink driver is held ‘ON’. 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 10 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO When the frequency of SIG_IN is higher than that of COMP_IN, the source output driver is held ‘ON’ for most of the input signal cycle time and for the remainder of the cycle time both drivers are ‘OFF’ (3-state). If the SIG_IN frequency is lower than the COMP_IN frequency, then it is the sink driver that is held ‘ON’ for most of the cycle. Subsequently the voltage at the capacitor (C2) of the low-pass filter connected to PC2_OUT varies until the signal and comparator inputs are equal in both phase and frequency. At this stable point the voltage on C2 remains constant as the PC2 output is in 3-state and the VCO input at pin 9 is a high-impedance. Also in this condition the signal at the phase comparator pulse output (PCP_OUT) has a minimum output pulse width equal to the overlap time, so can be used for indicating a locked condition. Thus for PC2 no phase difference exists between SIG_IN and COMP_IN over the full frequency range of the VCO. Moreover, the power dissipation due to the low-pass filter is reduced because both output drivers are OFF for most of the signal input cycle. It should be noted that the PLL lock range for this type of phase comparator is equal to the capture range and is independent of the low-pass filter. With no signal present at SIG_IN the VCO adjust, via PC2, to its lowest frequency. By using current sources as charge pump output on PC2, the dead zone or backlash time could be reduced to zero. Also, the pulse widening due to the parasitic output capacitance plays no role here. This enables a linear transfer function, even in the vicinity of the zero crossing. The differences between a voltage switch charge pump and a current switch charge pump are shown in Figure 11. SIG_IN COMP_IN VCO_OUT UP PC_IN DOWN 15 ns typical CURRENT AT PC2_OUT high-impedance OFF-state, (zero current) PC2_OUT/VCO_IN PCP_OUT mbd047 The pulse overlap of the up and down signals (typically 15 ns). Fig 10. Timing diagram for PC2 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 11 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 2.75 2.75 VCO_IN VCO_IN (1) 2.50 (1) 2.50 (2) 2.25 −25 0 phase error (ns) 25 2.25 −25 0 phase error (ns) 25 001aak444 001aak445 (1) Due to parasitic capacitance on PC2_OUT. (2) Backlash time (dead zone). a. Response with traditional voltage-switch charge-pump PC2_OUT (74HCT4046A). b. Response with current switch charge-pump PC2_OUT as applied in the 74HCT9046A. Fig 11. The response of a locked-loop in the vicinity of the zero crossing of the phase error The design of the low-pass filter is somewhat different when using current sources. The external resistor R3 is no longer present when using PC2 as phase comparator. The current source is set by Rbias. A simple capacitor behaves as an ideal integrator now, because the capacitor is charged by a constant current. The transfer function of the voltage switch charge pump may be used. In fact it is even more valid, because the transfer function is no longer restricted for small changes only. Further the current is independent from both the supply voltage and the voltage across the filter. For one that is familiar with the low-pass filter design of the 74HCT4046A a relation may show how Rbias relates with a fictive series resistance, called R3'. This relation can be derived by assuming first that a voltage controlled switch PC2 of the 74HCT4046A is connected to the filter capacitance C2 via this fictive R3' (see Figure 8b). Then during the PC2 output pulse the charge current equals: V CC – V C2 ( 0 ) I cp = -------------------------------R3' 2.5 With the initial voltage VC2(0) at: 0.5VCC = 2.5 V, I cp = ------R3' As shown before the charge current of the current switch of the 74HCT9046A is: 2.5 I cp = 17 × ----------R bias Hence: R bias R3 ‘ = ----------- ( Ω ) 17 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 12 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO Using this equivalent resistance R3' for the filter design the voltage can now be expressed as a transfer function of PC2; assuming ripple (fr = fi) is suppressed, as: 5 K PC2 = ----- ( V ⁄ r ) 4π Again this illustrates the supply voltage independent behavior of PC2. 8.4 Loop filter component selection Examples of PC2 combined with a passive filter are shown in Figure 12 and 13. Figure 12 shows that PC2 with only a C2 filter behaves as a high-gain filter. For stability the damped version of Figure 13 with series resistance R4 is preferred. Practical design values for Rbias are between 25 kΩ and 250 kΩ with R3' = 1.5 kΩ to 15 kΩ for the filter design. Higher values for R3' require lower values for the filter capacitance which is very advantageous at low values of the loop natural frequency ωn. A Icp Icp 17 Rbias F(jω) INPUT C2 OUTPUT −1/Aτ1 1/ Aτ 001aak449 1 ω 001aak450 001aak451 a. Simple loop filter for PC2 without damping b. Amplitude characteristic c. Pole zero diagram A = DC gain limit, due to leakage R bias τ 1 = ----------- × C2 = R3' × C2 17 1 1 F ( j ω ) = ---------------------------- ≈ ----------1 ⁄ A + j ωτ 1 j ωτ 1 Fig 12. Simple loop filter for PC2 without damping 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 13 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO A Icp Icp 17 R4 Rbias F(jω) INPUT C2 OUTPUT m O −1/τ2 1/Aτ 1 1/ Aτ 001aak446 1 1 / Aτ2 ω 001aak447 001aak448 a. Simple loop filter for PC2 with damping b. Amplitude characteristic c. Pole zero diagram A = DC gain limit, due to leakage R bias τ 1 = ----------- × C2 = R3 ‘ × C2 17 τ 2 = R4 × C2 1 + j ωτ 2 F ( j ω ) = ---------------------------1 ⁄ A + j ωτ 1 Fig 13. Simple loop filter for PC2 with damping 9. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC IIK IOK IO ICC IGND Tstg Ptot Parameter supply voltage input clamping current output clamping current output current supply current ground current storage temperature total power dissipation DIP16 SO16 and TSSOP16 [1] [2] For DIP16 packages: above 70 °C the value of Ptot derates linearly with 12 mW/K. For SO16 and TSSOP16 packages: above 70 °C the value of Ptot derates linearly with 8 mW/K. Conditions VI < −0.5 V or VI > VCC + 0.5 V VO < −0.5 V or VO > VCC + 0.5 V −0.5 V < VO < VCC + 0.5 V Min −0.5 −50 −65 Max +7 ±20 ±20 ±25 +50 +150 750 500 Unit V mA mA mA mA mA °C mW mW Tamb = −40 °C to +125 °C [1] [2] - 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 14 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 10. Recommended operating conditions Table 4. Symbol VCC VI VO Tamb ∆t/∆V Operating conditions Parameter supply voltage input voltage output voltage ambient temperature input transition rise and fall rate pin INH; VCC = 4.5 V Conditions Min 4.5 0 0 −40 1.67 Typ 5.0 Max 5.5 VCC VCC +125 139 Unit V V V °C ns/V 11. Static characteristics Table 5. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Tamb = 25 °C Phase comparator section VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage pins SIG_IN and COMP_IN; VCC = 4.5 V; DC coupled pins SIG_IN and COMP_IN; VCC = 4.5 V; DC coupled pins PCP_OUT and PCn_OUT; VCC = 4.5 V; VI = VIH or VIL IO = −20 µA IO = −4.0 mA VOL LOW-level output voltage pins PCP_OUT and PCn_OUT; VCC = 4.5 V; VI = VIH or VIL IO = 20 µA IO = 4.0 mA II IOZ RI input leakage current OFF-state output current input resistance pins SIG_IN and COMP_IN; VCC = 5.5 V; VI = VCC or GND pin PC2_OUT; VCC = 5.5 V; VI = VIH or VIL; VO = VCC or GND SIG_IN and COMP_IN; VCC = 4.5 V; VI at self-bias operating point; ∆VI = 0.5 V; see Figure 14, 15 and 16 Rbias Icp VCO section VIH VIL HIGH-level input voltage LOW-level input voltage pin INH; VCC = 4.5 V to 5.5 V; DC coupled pin INH; VCC = 4.5 V to 5.5 V; DC coupled 2.0 1.6 1.2 0.8 V V bias resistance charge pump current VCC = 4.5 V VCC = 4.5 V; Rbias = 40 kΩ 25 250 kΩ ±0.53 ±1.06 ±2.12 mA 250 ±0.5 µA kΩ 0 0.15 0.1 0.26 ±30 V V µA 4.4 3.98 4.5 4.32 V V 2.1 1.35 V 3.15 2.4 V Parameter Conditions Min Typ Max Unit 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 15 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO Table 5. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VOH Parameter HIGH-level output voltage Conditions pin VCO_OUT; VCC = 4.5 V; VI = VIH or VIL IO = −20 µA IO = −4.0 mA VOL LOW-level output voltage pin VCO_OUT; VCC = 4.5 V; VI = VIH or VIL IO = 20 µA IO = 4.0 mA pins C1A and C1B; VCC = 4.5 V; VI = VIH or VIL; IO = 4.0 mA II R1 R2 C1 VVCO_IN input leakage current resistor 1 resistor 2 capacitor 1 voltage on pin VCO_IN pins INH and VCO_IN; VCC = 5.5 V; VI = VCC or GND VCC = 4.5 V VCC = 4.5 V VCC = 4.5 V over the range specified for R1 VCC = 4.5 V VCC = 5.0 V VCC = 5.5 V Demodulator section Rs series resistance VCC = 4.5 V; at Rs > 300 kΩ the leakage current can influence VDEM_OUT VCO_IN to VDEM_OUT; VCC = 4.5 V; VI = VVCO_IN = 0.5VCC; values taken over Rs range; see Figure 17 DEM_OUT; VCC = 4.5 V; VDEM_OUT = 0.5VCC disabled; VCC = 5.5 V; pin INH at VCC pin INH; VI = VCC − 2.1 V; VCC = 4.5 V; other inputs at VCC or GND; 50 300 kΩ 1.1 1.1 1.1 3.4 3.9 4.4 V V V 3 3 40 0 0.15 0.1 0.26 0.40 ±0.1 300 300 no limit V V V µA kΩ kΩ pF 4.4 3.98 4.5 4.32 V V Min Typ Max Unit Voffset offset voltage - ±20 - mV Rdyn General ICC ∆ICC CI dynamic resistance - 25 - Ω supply current additional supply current input capacitance - 100 3.5 8.0 360 - µA µA pF Tamb = −40 °C to +85 °C Phase comparator section VIH VIL HIGH-level input voltage LOW-level input voltage pins SIG_IN and COMP_IN; VCC = 4.5 V; DC coupled pins SIG_IN and COMP_IN; VCC = 4.5 V; DC coupled 1.35 V 3.15 V 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 16 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO Table 5. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VOH Parameter HIGH-level output voltage Conditions pins PCP_OUT and PCn_OUT; VCC = 4.5 V; VI = VIH or VIL IO = −20 µA IO = −4.0 mA VOL LOW-level output voltage pins PCP_OUT and PCn_OUT; VCC = 4.5 V; VI = VIH or VIL IO = 20 µA IO = 4.0 mA II IOZ VCO section VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage pin INH; VCC = 4.5 V to 5.5 V; DC coupled pin INH; VCC = 4.5 V to 5.5 V; DC coupled pin VCO_OUT; VCC = 4.5 V; VI = VIH or VIL IO = −20 µA IO = −4.0 mA VOL LOW-level output voltage pin VCO_OUT; VCC = 4.5 V; VI = VIH or VIL IO = 20 µA IO = 4.0 mA pins C1A and C1B; VCC = 4.5 V; VI = VIH or VIL; IO = 4.0 mA II General ICC ∆ICC supply current additional supply current disabled; VCC = 5.5 V; pin INH at VCC per input pin; VI = VCC − 2.1 V; VCC = 4.5 V; other inputs at VCC or GND; 80.0 450 µA µA input leakage current pins INH and VCO_IN; VCC = 5.5 V; VI = VCC or GND 0.1 0.33 0.47 ±1.0 V V V µA 4.4 3.84 V V 2.0 0.8 V V input leakage current OFF-state output current SIG_IN and COMP_IN; VCC = 5.5 V; VI = VCC or GND PC2_OUT; VCC = 5.5 V; VI = VIH or VIL; VO = VCC or GND ±5.0 µA 0.1 0.33 ±38 V V µA 4.4 3.84 V V Min Typ Max Unit Tamb = −40 °C to +125 °C Phase comparator section VIH VIL HIGH-level input voltage LOW-level input voltage pins SIG_IN and COMP_IN; VCC = 4.5 V; DC coupled pins SIG_IN and COMP_IN; VCC = 4.5 V; DC coupled 1.35 V 3.15 V 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 17 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO Table 5. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VOH Parameter HIGH-level output voltage Conditions pins PCP_OUT and PCn_OUT; VCC = 4.5 V; VI = VIH or VIL IO = −20 µA IO = −4.0 mA VOL LOW-level output voltage pins PCP_OUT and PCn_OUT; VCC = 4.5 V; VI = VIH or VIL IO = 20 µA IO = 4.0 mA II IOZ VCO section VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage pin INH; VCC = 4.5 V to 5.5 V; DC coupled pin INH; VCC = 4.5 V to 5.5 V; DC coupled pin VCO_OUT; VCC = 4.5 V; VI = VIH or VIL IO = −20 µA IO = −4.0 mA VOL LOW-level output voltage pin VCO_OUT; VCC = 4.5 V; VI = VIH or VIL IO = 20 µA IO = 4.0 mA pins C1A and C1B; VCC = 4.5 V; VI = VIH or VIL; IO = 4.0 mA II General ICC ∆ICC supply current additional supply current disabled; VCC = 5.5 V; pin INH at VCC per input pin; VI = VCC − 2.1 V; VCC = 4.5 V; other inputs at VCC or GND; 160.0 µA 490 µA input leakage current pins INH and VCO_IN; VCC = 5.5 V; VCC or GND 0.1 0.4 0.54 ±1.0 V V V µA 4.4 3.7 V V 2.0 0.8 V V input leakage current OFF-state output current pins SIG_IN and COMP_IN; VCC = 5.5 V; VI = VCC or GND pin PC2_OUT; VCC = 5.5 V; VI = VIH or VIL; VO = VCC or GND ±10.0 µA 0.1 0.4 ±45 V V µA 4.4 3.7 V V Min Typ Max Unit 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 18 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO mbd108 800 RI (kΩ) mga956 - 1 II ∆VI 600 400 VCC = 4.5 V 200 self-bias operating point 0 (0.5 VCC) − 0.25 0.5 VCC 5.5 V VI (V) (0.5 VCC) + 0.25 VI Fig 14. Typical input resistance curve at SIG_IN and COMP_IN mga957 Fig 15. Input resistance at SIG_IN; COMP_IN with ∆VI = 0.5 V at self-bias point 60 Voffset (mV) 40 mga958 5 VCC = 5.5V 4.5 V II (µA) 20 0 0 4.5 V 5.5 V −20 5.5 V VCC = 4.5 V −5 (0.5 VCC) − 0.25 0.5 VCC VI (V) (0.5 VCC) + 0.25 −40 (0.5 VCC) − 2 0.5 VCC (0.5 VCC) + 2 VVCO_IN (V) ___ Rs = 50 kΩ - - - Rs = 300 kΩ Fig 16. Input current at SIG_IN; COMP_IN with ∆VI = 0.5 V at self-bias point Fig 17. Offset voltage at demodulator output as a function of VCO_IN and Rs 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 19 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 12. Dynamic characteristics Table 6. Dynamic characteristics[1] GND = 0 V; tr = tf = 6 ns; CL = 50 pF. Symbol Tamb = 25 °C Phase comparator section tpd propagation delay SIG_IN, COMP_IN to PC1_OUT; VCC = 4.5 V; see Figure 18 SIG_IN, COMP_IN to PCP_OUT; VCC = 4.5 V; see Figure 18 ten tdis tt Vi(p-p) VCO section ∆f f0 frequency deviation center frequency VCC = 5.0 V; VVCO_IN = 3.9 V; R1 = 10 kΩ; R2 = 10 kΩ; C1 = 1 nF VCC = 4.5 V; duty cycle = 50 %; VVCO_IN = 0.5VCC; R1 = 4.3 kΩ; R2 = ∞ Ω; C1 = 40 pF; see Figure 23 and 31 VCC = 5 V; duty cycle = 50 %; VVCO_IN = 0.5VCC; R1 = 3 kΩ; R2 = ∞ Ω; C1 = 40 pF; see Figure 23 and 31 ∆f/f δ General CPD power dissipation capacitance [2][3] [5] Parameter Conditions Min Typ Max Unit [4] 23 35 30 36 7 50 40 68 56 65 15 - ns ns ns ns ns mV enable time disable time transition time peak-to-peak input voltage SIG_IN, COMP_IN to PC2_OUT; VCC = 4.5 V; see Figure 19 SIG_IN, COMP_IN to PC2_OUT; VCC = 4.5 V; see Figure 19 VCC = 4.5 V; see Figure 18 pin SIGN_IN or COMP_IN; VCC = 4.5 V; AC coupled; fi = 1 MHz - −10 11.0 15.0 +10 - % MHz - 16.0 - MHz relative frequency variation duty cycle VCC = 4.5 V; R1 = 100 kΩ; R2 = ∞ Ω; C1 = 100 pF; see Figure 24 and 25 VCO_OUT; VCC = 4.5 V [6] - 0.4 50 20 - % % pF Tamb = −40 °C to +85 °C Phase comparator section tpd propagation delay SIG_IN, COMP_IN to PC1_OUT; VCC = 4.5 V; see Figure 18 SIG_IN, COMP_IN to PCP_OUT; VCC = 4.5 V; see Figure 18 ten tdis tt VCO section enable time disable time transition time SIG_IN, COMP_IN to PC2_OUT; VCC = 4.5 V; see Figure 19 SIG_IN, COMP_IN to PC2_OUT; VCC = 4.5 V; see Figure 19 VCC = 4.5 V; see Figure 18 70 81 19 ns ns ns 85 ns 50 ns 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 20 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO Table 6. Dynamic characteristics[1] …continued GND = 0 V; tr = tf = 6 ns; CL = 50 pF. Symbol ∆f/∆T Parameter frequency variation with temperature Conditions VCC = 4.5 V; VVCO_IN = 0.5VCC; recommended range: R1 = 10 kΩ; R2 = 10 kΩ; C1 = 1 nF; see Figure 20, 21 and 22 [7] Min - Typ 0.06 Max - Unit %/K Tamb = −40 °C to +125 °C Phase comparator section tpd propagation delay SIG_IN, COMP_IN to PC1_OUT; VCC = 4.5 V; see Figure 18 SIG_IN, COMP_IN to PCP_OUT; VCC = 4.5 V; see Figure 18 ten tdis tt [1] [2] - - 60 102 84 98 22 ns ns ns ns ns enable time disable time transition time SIG_IN, COMP_IN to PC2_OUT; VCC = 4.5 V; see Figure 19 SIG_IN, COMP_IN to PC2_OUT; VCC = 4.5 V; see Figure 19 VCC = 4.5 V; see Figure 18 tpd is the same as tPLH and tPHL; tdis is the same as tPLZ and tPHZ; ten is the same as tPZL and tPZH; tt is the same as tTLH and tTHL. CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + ∑(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = total load switching outputs; ∑(CL × VCC2 × fo) = sum of outputs. Applies to the phase comparator section only (pin INH = HIGH). For power dissipation of the VCO and demodulator sections, see Figure 26, 27 and 28. This is the (peak to peak) input sensitivity. This is the center frequency tolerance. This is the frequency linearity. This is the frequency stability with temperature change. [3] [4] [5] [6] [7] SIG_IN, COMP_IN inputs VM tPHL tPLH PCP_OUT, PC1_OUT outputs VM tTHL tTLH mbd106 VM = 0.5VCC; VI = GND to VCC. Fig 18. Waveforms showing input (SIG_IN and COMP_IN) to output (PCP_OUT and PC1_OUT) propagation delays and the output transition times 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 21 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO SIG_IN input VM COMP_IN input VM tPHZ 90% tPLZ tPZH PC2_OUT output tPZL VM 10% mga941 VM = 0.5VCC; VI = GND to VCC. Fig 19. Waveforms showing the enable and disable times for PC2_OUT 20 ∆f (%) 10 mbd115 ∆f (%) 15 mbd116 10 5 0 0 VCC = −10 5.5 V 4.5 V −20 −50 0 50 100 150 Tamb (°C) −5 −10 VCC = 5.5 V 4.5 V −15 −50 0 50 100 150 Tamb (°C) a. R1 = 3 kΩ; R2 = ∞ Ω; C1 = 100 pF. b. R1 = 10 kΩ; R2 = ∞ Ω; C1 = 100 pF. Fig 20. Frequency stability of the VCO as a function of ambient temperature with supply voltage as a parameter 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 22 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 10 ∆f (%) 5 mbd124 VCC = 5.5 V 4.5 V ∆f (%) 15 10 5 0 mbd117 VCC = 0 −5 −5 −10 −15 −10 −50 −20 −50 5.5 V 4.5 V 0 50 100 150 Tamb (°C) 0 50 100 150 Tamb (°C) a. R1 = 300 kΩ; R2 = ∞ Ω; C1 = 100 pF. b. R1 = ∞ Ω; R2 = 3 kΩ; C1 = 100 pF. Fig 21. Frequency stability of the VCO as a function of ambient temperature with supply voltage as a parameter 8 ∆f (%) 4 mbd118 10 ∆f (%) 5 mbd119 0 0 −4 VCC = 5.5 V −5 VCC = 4.5 V 5.5 V −8 4.5 V −12 −50 0 50 100 150 Tamb (°C) −10 −50 0 50 100 150 Tamb (°C) a. R1 = ∞ Ω; R2 = 10 kΩ; C1 = 100 pF. b. R1 = ∞ Ω; R2 = 300 kΩ; C1 = 100 pF. Fig 22. Frequency stability of the VCO as a function of ambient temperature with supply voltage as a parameter 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 23 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 30 fVCO (MHz) 20 VCC = 4.5 V 10 5.5 V mbd112 30 fVCO (kHz) 20 VCC = 4.5 V mbd113 5.5 V 10 0 0 2 4 VVCO_IN (V) 6 0 0 2 4 VVCO_IN (V) 6 a. R1 = 4.3 kΩ; C1 = 39 pF. mbd120 b. R1 = 4.3 kΩ; C1 = 100 nF. mbd111 800 fVCO (kHz) 600 VCC = 5.5 V 4.5 V 400 f VCO (Hz) 300 VCC = 5.5 V frequency 4.5 V frequency 400 200 200 100 0 0 2 4 VVCO_IN (V) 6 0 0 2 4 VVCO_IN (V) 6 c. R1 = 300 kΩ; C1 = 39 pF. d. R1 = 300 kΩ; C1 = 100 nF. Fig 23. Graphs showing VCO frequency as a function of the VCO input voltage (VVCO_IN) 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 24 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 4 mbd114 mga937 fVCO (%) 0 C1 = 1 µF 4.5 V 5.5 V f (MHz) f2 f0 f' 0 f1 C1 = 39 pF 4.5 V −4 V min 0.5 VCC V max VVCO_IN (V) −8 1 5.5 V 10 10 2 3 R1 (kΩ) 10 f1 + f2 f ‘ 0 = ----------------2 linearity = ----------------- × 100 % - R2 = ∞ Ω and ∆V = 0.5 V f ‘0 – f 0 f0 Fig 24. Definition of VCO frequency linearity: ∆V = 0.5 V over the VCC range mbd121 Fig 25. Frequency linearity as a function of R1, C1 and VCC 1 VCC = 5.5 V C1 = 39 pF 4.5 V C1 = 39 pF mbd110 1 PD (W) VCC = 5.5 V C1 = 1 µF 4.5 V C1 = 1 µF PD (W) 10 1 10 5.5 V C1 = 39 pF 4.5 V C1 = 39 pF 1 5.5 V 4.5 V C1 = 1 µF 10 2 10 0 100 200 R1 (kΩ) 300 2 0 R1 = ∞ Ω 100 200 R2 (kΩ) 300 R2 = ∞ Ω Fig 26. Power dissipation as a function of R1 Fig 27. Power dissipation as a function of R2 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 25 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 10 3 mbd109 PDEM (W) VCC = 10 4 4.5 V 5.5 V 10 5 10 102 Rs (kΩ) 10 3 Fig 28. Typical power dissipation as a function of Rs 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 26 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 13. Application information This information is a guide for the approximation of values of external components to be used with the 74HCT9046A in a phase-locked-loop system. Values of the selected components should be within the ranges shown in Table 7. Table 7. R1 R2 R1 + R2 C1 Table 8. Subject VCO frequency without extra offset Survey of components Value between 3 kΩ and 300 kΩ between 3 kΩ and 300 kΩ parallel value > 2.7 kΩ > 40 pF Design considerations for VCO section Phase comparator PC1, PC2 Design consideration VCO frequency characteristic. With R2 = ∞ and R1 within the range 3 kΩ < R1 < 300 kΩ, the characteristics of the VCO operation will be as shown in Figure 29a. (Due to R1, C1 time constant a small offset remains when R2 = ∞ Ω). Selection of R1 and C1. Given f0, determine the values of R1 and C1 using Figure 31. Given fmax and f0 determine the values of R1 and C1 using Figure 31; use Figure 33 to obtain 2fL and then use this to calculate fmin. VCO frequency characteristic. With R1 and R2 within the ranges 3 kΩ < R1 < 300 kΩ < R2 < 300 kΩ, the characteristics of the VCO operation is as shown in Figure 29b. Selection of R1, R2 and C1. Given f0 and fL determine the value of product R1C1 by using Figure 33. Calculate foff from the equation foff = f0 − 1.6fL. Obtain the values of C1 and R2 by using Figure 32. Calculate the value of R1 from the value of C1 and the product R1C1. VCO adjusts to f0 with ΦPC_IN = 90° and VVCO_IN = 0.5VCC VCO adjusts to foffset with ΦPC_IN = −360° and VVCO_IN = minimum Component PC1 PC2 VCO frequency with extra offset PC1, PC2 PC1, PC2 PLL conditions with no signal at pin SIG_IN PC1 PC2 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 27 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO mga938 f VCO f max f0 f min 1.1 V 0.5 VCC VCC−1.1 V VCC 2f L due to R1,C1 VCO_IN a. Operating without offset; f0 = center frequency; 2fL = frequency lock range. mga939 f VCO f max f0 f min f off 0.6fL due to R2,C1 2fL due to R1,C1 1.1 V 0.5 VCC VCC−1.1 V VCC VCO_IN b. Operating with offset; f0 = center frequency; 2fL = frequency lock range. Fig 29. Frequency characteristic of VCO 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 28 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 13.1 Filter design considerations for PC1 and PC2 of the 74HCT9046A Figure 30 shows some examples of passive and active filters to be used with the phase comparators of the 74HCT9046A. Transfer functions of phase comparators and filters are given in Table 9. Table 9. Transfer functions of phase comparators and filters Explanation V CC K PC1 = ---------- V /r π τ1 = R3 × C2; τ2 = R4 × C2; τ3 = R4 × C3; A = 105 = DC gain amplitude PC2 5 K PC + ----- V / r 4π Figure Figure 30a Filter type passive filter without damping passive filter with damping active filter with damping passive filter with damping Transfer function 1 F ( j ω ) = --------------------1 + j ωτ 1 1 + j ωτ 2 F ( j ω ) = ------------------------------------1 + j ω ( τ1 + τ2 ) 1 + j ωτ 2 1 + j ωτ 2 F ( j ω ) = --------------------------- ≈ --------------------1 / A + j ωτ 1 j ωτ 1 1 + j ωτ 2 1 + j ωτ 2 F ( j ω ) = ---------------------------- ≈ --------------------1 ⁄ A + j ωτ 1 j ωτ 1 A = 105 = DC gain amplitude active filter with damping 1 + j ωτ 2 1 + j ωτ 2 F ( j ω ) = --------------------------- ≈ --------------------1 / A + j ωτ 1 j ωτ 1 A = 105 = DC gain amplitude Phase comparator PC1 Figure 30b Figure 30c Figure 30d τ1 = R3’ × C2; τ2 = R4 × C2; Figure 30e τ3 = R4 × C3; R3' = Rbias/17; Rbias = 25 kΩ to 250 kΩ Table 10. Subject General design considerations Phase comparator PC1 PC2 PC1 PC2 PC1 PC2 Design consideration yes no high low fr = 2fi; large ripple content at ΦPC_IN = 90° fr = fi; small ripple content at ΦPC_IN = 0° PLL locks on harmonics at center frequency Noise rejection at signal input AC ripple content when PLL is locked 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 29 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO PC1 CIRCUIT F(jω ) R3 AMPLITUDE CHARACTERISTIC POLE ZERO DIAGRAM C2 1/ τ 1 X 1/ τ 1 (a) F(jω ) R3 1/ τ 2 C3 R4 1/ τ 3 O 1/ τ 2 X 1 1/ τ 1 τ 2 C2 τ1 τ2 (b) A C3 C2 R4 R3 1/ τ 2 1/ τ 3 O 1/ τ 2 X 1/ A τ 1 1/ A τ 1 A (c) PC2 A R3' 1/ τ 2 R4 1/ τ 3 O 1/ τ 2 X 1/ A τ 1 AR3' C2 1/A τ 1 (d) A C3 C2 R4 R3' 1/ τ 2 1/ τ 3 O 1/ τ 2 X 1/ A τ 1 A 1/A τ 1 (e) mbd107 Fig 30. Passive and active filters for 74HCT9046A 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 30 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 108 f0 (Hz) 107 106 105 104 103 102 10 1 10 102 103 104 105 mbd103 (1) (2) (3) (4) (5) (6) (7) (8) 106 107 C1 (pF) VCC = 5.5 V; R1 = 3 kΩ. VCC = 4.5 V; R1 = 3 kΩ. VCC = 5.5 V; R1 = 10 kΩ. VCC = 4.5 V; R1 = 10 kΩ. VCC = 5.5 V; R1 = 150 kΩ. VCC = 4.5 V; R1 = 150 kΩ. VCC = 5.5 V; R1 = 300 kΩ. VCC = 4.5 V; R1 = 300 kΩ. R2 = ∞ Ω; VVCO_IN = 0.5VCC; INH = GND; Tamb = 25 °C. Fig 31. Typical value of VCO center frequency (f0) as a function of C1 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 31 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 108 foff (Hz) 107 106 105 104 103 102 10 1 10 102 103 104 105 mbd104 (1) (2) (3) (4) 106 107 C1 (pF) VCC = 4.5 V to 5.5 V; R1 = 3 kΩ. VCC = 4.5 V to 5.5 V; R1 = 10 kΩ. VCC = 4.5 V to 5.5 V; R1 = 150 kΩ. VCC = 4.5 V to 5.5 V; R1 = 300 kΩ. R1 = ∞ Ω; VVCO_IN = 0.5VCC; INH = GND; Tamb = 25 °C. Fig 32. Typical value of frequency offset as a function of C1 108 2fL (Hz) 107 106 105 104 103 102 10 10−7 mbd105 VCC = 5.5 V 4.5 V 10−6 10−5 10−4 10−3 10−2 10−1 1 R1C1 (s) 2fL K v = --------------------------------------- 2 π ( r ⁄ s ⁄ V ) V VCO _ IN range VVCO_IN = 1.1 V to (VCC − 1.1) V Fig 33. Typical frequency lock range 2fL as a function of the product R1 and C1 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 32 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 13.2 PLL design example The frequency synthesizer used in the design example shown in Figure 34 has the following parameters: Output frequency: 2 MHz to 3 MHz Frequency steps: 100 kHz Settling time: 1 ms Overshoot: < 20 % The open loop gain is: H (s) × G (s) = K p × K f × K o × K n and the closed loop: K p × K f × Ko × Kn Φu ------ = ------------------------------------------------------1 + K p × K f × Ko × Kn Φi where: Kp = phase comparator gain Kf = low-pass filter transfer gain Ko = Kv/s VCO gain Kn = 1⁄n divider ratio The programmable counter ratio Kn can be found as follows: f OUT 2 MHz N min = ------------ = -------------------- = 20 100 kHz f step f OUT 3 MHz N max = ------------ = -------------------- = 30 f step 100 kHz The VCO is set by the values of R1, R2 and C1; R2 = 10 kΩ (adjustable). The values can be determined using the information in Table 8. With f0 = 2.5 MHz and fL = 500 kHz this gives the following values (VCC = 5.0 V): R1 = 30 kΩ R2 = 30 kΩ C1 = 100 pF The VCO gain is: 2 f L × 2π 1 MHz 6 K v = ----------------------------------------- = ---------------- × 2 π ≈ 2.24 × 10 r ⁄ s ⁄ V 2.8 ( V CC – 1.1 ) – 1.1 The gain of the phase comparator PC2 is: 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 33 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 5 K p = ----------- = 0.4 V ⁄ r 4×π Using PC2 with the passive filter as shown in Figure 34 results in a high gain loop with the same performance as a loop with an active filter. Hence loop filter equations as for a high gain loop should be used. The current source output of PC2 can be simulated then with a fictive filter resistance: R bias R3 ‘ = ----------17 The transfer functions of the filter is given by: 1 + s τ2 K f = ---------------s τ2 Where: τ 1 = R3 ‘ × C2 τ 2 = R4 × C2 The characteristic equation is: 1 + K p × K f × K o × K n This results in: 1 + s τ2 K v 1 + K p  ----------------  ----- K n = 0  s τ 1 - sor: τ2 2 s + sK p K v K n ---- + K p K v K n ⁄ τ 1 = 0 τ1 This can be written as: s + 2 ξω n s + ( ω n ) = 0 with the natural frequency ωn defined as: ωn = K p × Kv × Kn -------------------------------τ1 2 2 and the damping value given as: ζ = 0.5 × τ 2 × ω n In Figure 35 the output frequency response to a step of input frequency is shown. The overshoot and settling time percentages are now used to determine ωn. From Figure 35 it can be seen that the damping ratio ζ = 0.707 will produce an overshoot of less than 20 % and settle to within 5 % at ωnt = 5. The required settling time is 1 ms. This results in: 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 34 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 3 5 5 ω n = -- = ------------ = 5 × 10 r ⁄ s t 0.001 Rewriting the equation for natural frequency results in: K p × Kv × Kn τ 1 = -------------------------------2 ( ωn ) The maximum overshoot occurs at Nmax = 30; hence Kn = 1⁄30: 0.4 × 2.24 × 10 τ 1 = -------------------------------------- = 0.0012 2 5000 × 30 When C2 = 470 nF, it follows: τ1 0.0012 R3 ‘ = ------ = ------------------------- = 2550 Ω –9 C2 470 × 10 Hence the current source bias resistance R bias = 17 × 2550 = 43 k Ω With ζ = 0.707 (0.5 × τ2 × ωn) it follows: 0.707 τ 2 = ------------------------- = 0.00028 0.5 × 5000 τ2 0.00028 R4 = ------ = ------------------------- = 600 Ω –9 C2 470 × 10 For extra ripple suppression a capacitor C3 can be connected in parallel with R4, with an extra τ3 = R4 × C3. For stability reasons τ3 should be < 0.1τ2, hence C3 < 0.1C2 or C3 = 39 nF. 6 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 35 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO Kp 100 kHz OSCILLATOR "HCU04" DIVIDE BY 10 "190" 14 3 PHASE COMPARATOR PC2 R3' (1) Kf 13 R4 C3 C2 R1 Ko 9 4 fOUT VCO 11 R2 C1 15 12 6 7 5 Φu 1 MHz Kn PROGRAMMABLE DIVIDER "4059" Rbias mbd098 (1) R3’ = fictive resistance R3’ = -----------C1 = 100 pF C2 = 470 nF C3 = 39 nF R1 = 30 kΩ R2 = 30 kΩ R3' = 2550 Ω Rbias = 43 kΩ R4 = 600 Ω R bias 17 Fig 34. Frequency synthesizer 1.6 mga959 −0.6 −0.4 −0.2 ∆ωe(t) ∆ωe/ωn 1.4 ζ = 0.3 0.5 0.707 1.0 ∆Φe(t) ∆Φe/ωn 1.2 ζ = 5.0 1.0 ζ = 2.0 0 0.8 0.2 0.6 0.4 0.4 0.6 0.2 0.8 0 0 1 2 3 4 5 6 7 ωnt 8 1.0 Fig 35. Type 2, second order frequency step response 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 36 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 3.1 proportional to output frequency (MHz) 2.9 step input 2.1 N stepped from 21 to 20 2.0 N = 30 mga952 N stepped from 29 to 30 1.9 0 0.5 1.0 1.5 2.0 2.5 time (ms) Fig 36. Frequency compared to the time response Since the output frequency is proportional to the VCO control voltage, the PLL frequency response can be observed with an oscilloscope by monitoring pin VCO_IN of the VCO. The average frequency response, as calculated by the Laplace method, is found experimentally by smoothing this voltage at pin VCO_IN with a simple RC filter, whose time constant is long compared with the phase detector sampling rate but short compared with the PLL response time. 13.3 Further information For an extensive description and application example please refer to “Application note” ordering number 9397 750 00078. 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 37 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 14. Package outline DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4 D seating plane ME A2 A L A1 c Z e b1 b 16 9 b2 MH wM (e 1) pin 1 index E 1 8 0 5 scale 10 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.02 A2 max. 3.2 0.13 b 1.73 1.30 0.068 0.051 b1 0.53 0.38 0.021 0.015 b2 1.25 0.85 0.049 0.033 c 0.36 0.23 0.014 0.009 D (1) 19.50 18.55 0.77 0.73 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.1 e1 7.62 0.3 L 3.60 3.05 0.14 0.12 ME 8.25 7.80 0.32 0.31 MH 10.0 8.3 0.39 0.33 w 0.254 0.01 Z (1) max. 0.76 0.03 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT38-4 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 95-01-14 03-02-13 Fig 37. Package outline SOT38-4 (DIP16) 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 38 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index θ Lp 1 e bp 8 wM L detail X A1 (A 3) A 0 2.5 scale 5 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07 JEDEC MS-012 JEITA EUROPEAN PROJECTION A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3 θ 0.010 0.057 0.069 0.004 0.049 0.019 0.0100 0.39 0.014 0.0075 0.38 0.244 0.041 0.228 0.028 0.004 0.012 8 o 0 o ISSUE DATE 99-12-27 03-02-19 Fig 38. Package outline SOT109-1 (SO16) 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 39 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index A1 θ Lp L (A 3) A 1 e bp 8 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.40 0.06 θ 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 39. Package outline SOT403-1 (TSSOP16) 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 40 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 15. Abbreviations Table 11. Acronym CMOS DUT ESD HBM MM PLL VCO Abbreviations Description Complementary Metal Oxide Semiconductor Device Under Test ElectroStatic Discharge Human Body Model Machine Model Phase Locked Loop Voltage Controlled Oscillator 16. Revision history Table 12. Revision history Release date 20090915 Data sheet status Product data sheet Change notice Supersedes 74HCT9046A_5 Document ID 74HCT9046A_6 Modifications: • • • • • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Vi(p-p) value changed from 15 mV to 50 mV in Section 12. ∆f/∆T value moved from minimum to typical column Section 12. Package version SOT38-1 changed to SOT38-4 in Section 4 and Figure 37. Product specification Product specification Product specification 74HCT9046A_4 74HCT9046A_3 - 74HCT9046A_5 74HCT9046A_4 74HCT9046A_3 20031030 20030515 19990111 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 41 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 17. Legal information 17.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term ‘short data sheet’ is explained in section “Definitions”. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 17.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 17.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental 17.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 18. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com 74HCT9046A_6 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 06 — 15 September 2009 42 of 43 NXP Semiconductors 74HCT9046A PLL with band gap controlled VCO 19. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 8.2 8.3 8.3.1 8.3.2 8.4 9 10 11 12 13 13.1 13.2 13.3 14 15 16 17 17.1 17.2 17.3 17.4 18 19 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 6 Differences with respect to the familiar 74HCT4046A . . . . . . . . . . . . . . . . . . . . . . . . . . 6 VCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Phase comparators. . . . . . . . . . . . . . . . . . . . . . 7 Phase Comparator 1 (PC1) . . . . . . . . . . . . . . . 7 Phase Comparator 2 (PC2) . . . . . . . . . . . . . . . 9 Loop filter component selection . . . . . . . . . . . 13 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 14 Recommended operating conditions. . . . . . . 15 Static characteristics. . . . . . . . . . . . . . . . . . . . 15 Dynamic characteristics . . . . . . . . . . . . . . . . . 20 Application information. . . . . . . . . . . . . . . . . . 27 Filter design considerations for PC1 and PC2 of the 74HCT9046A . . . . . . . . . . . . . . . . 29 PLL design example . . . . . . . . . . . . . . . . . . . . 33 Further information . . . . . . . . . . . . . . . . . . . . . 37 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 38 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 41 Legal information. . . . . . . . . . . . . . . . . . . . . . . 42 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 42 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Contact information. . . . . . . . . . . . . . . . . . . . . 42 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 15 September 2009 Document identifier: 74HCT9046A_6