ADC1413S

ADC1413S series Single 14-bit ADC; 65 Msps, 80 Msps, 105 Msps or 125 Msps; serial JESD204A interface Rev. 2 — 8 June 2011 Product data sheet 1. General description The ADC1413S is a single channel 14-bit Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power at sample rates up to 125 Msps. Pipelined architecture and output error correction ensure the ADC1413S is accurate enough to guarantee zero missing codes over the entire operating range. Supplied from a 3 V source for analog and a 1.8 V source for the output driver, it outputs data in serial mode via a single differential lane, which complies with the JESD204A standard. The integration of Serial Peripheral Interface (SPI) allows the user to easily configure the ADCs and the serial output modes. The device also includes a programmable full-scale SPI to allow a flexible input voltage range from 1 V (p-p) to 2 V (p-p). Excellent dynamic performance is maintained from the baseband to input frequencies of 170 MHz or more, making the ADC1413S ideal for use in communications, imaging, and medical applications. 2. Features and benefits  SNR, 72.1 dBFS; SFDR, 86 dBc  Sample rates up to 125 Msps  Single channel, 14-bit pipelined ADC core  3 V, 1.8 V power supplies  Flexible input voltage range: 1 V (p-p) to 2 V (p-p)  serial output  Compliant with JESD204A serial transmission standard  Pin compatible with the ADC1613S series, ADC1213S series, and ADC1113S125  Input bandwidth, 600 MHz  Power dissipation, 550 mW at 80 Msps  SPI register programming  Duty cycle stabilizer  High Intermediate Frequency (IF) capability  Offset binary, two’s complement, gray code  Power-down mode and Sleep mode  HVQFN32 package 3. Applications  Wireless and wired broadband communications  Spectral analysis  Ultrasound equipment  Portable instrumentation  Imaging systems NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 4. Ordering information Table 1. Ordering information Sampling frequency (Msps) 125 105 80 65 Package Name Description Version Type number ADC1413S125HN/C1 ADC1413S105HN/C1 ADC1413S080HN/C1 ADC1413S065HN/C1 HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm 5. Block diagram SDIO SCLK CS SPI SYNC_P SYNC_N CLKP DLL PLL CLKM ERROR CORRECTION AND DIGITAL PROCESSING ENCODER 8-bit/10-bit A FRAME ASSEMBLY INP T/H INPUT STAGE INM ADC CORE 14-BIT PIPELINED OTR D13 to D0 SCRAMBLER A SERIALIZER A 10-bit OUTPUT BUFFER A CMLP 8-bit 8-bit CMLN CLOCK INPUT STAGE & DUTY CYCLE CONTROL ADC1413S SYSTEM REFERENCE AND POWER MANAGEMENT OTR SENSE VDDD AGND DGND VDDA 005aaa196 Fig 1. ADC1413S_SER Block diagram All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 2 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 6. Pinning information 6.1 Pinning 26 SYNCN 25 SYNCP 31 SENSE 28 DGND 30 AGND 27 VDDD 29 VDDA terminal 1 index area 32 VREF CLKP CLKM AGND REFB REFT VCM INM INP 1 2 3 4 24 n.c. 23 DGND 22 DGND 21 VDDD ADC1413S 5 6 7 8 20 CMLN 19 CMLP 18 VDDD 17 DGND VDDA 10 SDIO 12 CS 13 OTR 14 VDDD 15 DGND 16 VDDA SCLK 11 9 005aaa200 Transparent top view Fig 2. Pinning diagram 6.2 Pin description Table 2. Symbol CLKP CLKM AGND REFB REFT VCM INM INP VDDA VDDA SCLK SDIO CS ADC1413S_SER Pin description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Type [1] I I G O O O I I P P I I/O I Description clock input complementary clock input analog ground ADC bottom reference ADC top reference ADC output common voltage ADC complementary analog input ADC analog input analog power supply 3 V analog power supply 3 V SPI clock SPI data input/output chip select © NXP B.V. 2011. All rights reserved. All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 2 — 8 June 2011 3 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Pin description …continued Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Type [1] O P G G P O O P G G I I P G P G I I/O Description out-of-range information digital power supply 1.8 V digital ground digital ground digital power supply 1.8 V serial output serial complementary output digital power supply 1.8 V digital ground digital ground not connected positive synchronization signal from the receiver negative synchronization signal from the receiver digital power supply 1.8 V digital ground analog power supply 3 V analog ground reference programming pin voltage reference input/output Table 2. Symbol OTR VDDD DGND DGND VDDD CMLP CMLN VDDD DGND DGND n.c. SYNCP SYNCN VDDD DGND VDDA AGND SENSE VREF [1] P: power supply; G: ground; I: input; O: output; I/O: input/output. 7. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VDDA VDDD(1V8) Tstg Tamb Tj Parameter analog supply voltage digital supply voltage (1.8 V) storage temperature ambient temperature junction temperature Conditions Min 0.4 0.4 55 40 Max +4.6 +2.5 +125 +85 125 Unit V V C C C ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 4 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 8. Thermal characteristics Table 4. Symbol Rth(j-a) Rth(j-c) [1] Thermal characteristics Parameter thermal resistance from junction to ambient thermal resistance from junction to case Conditions [1] [1] Typ 25.6 8.6 Unit K/W K/W Value for six layers board in still air with a minimum of 25 thermal vias. 9. Static characteristics Table 5. Symbol Supplies VDDA VDDD(1V8) IDDA IDDD(1V8) Ptot analog supply voltage digital supply voltage (1.8 V) analog supply current digital supply current (1.8 V) total power dissipation fclk = 125 Msps; fi = 70 MHz fclk = 125 Msps; fi = 70 MHz fclk = 125 Msps fclk = 105 Msps fclk = 80 Msps fclk = 65 Msps P Digital inputs Clock inputs: pins CLKP and CLKM (AC-coupled) Low-Voltage Positive Emitter-Coupled Logic (LVPECL) Vi(clk)dif Sine Vi(clk)dif differential clock input voltage LOW-level input voltage HIGH-level input voltage LOW-level input voltage HIGH-level input voltage LOW-level input current HIGH-level input current input capacitance peak 0.8 3.0 V differential clock input voltage peak-to-peak 1.6 V power dissipation Power-down mode Standby mode 2.85 1.65 3.0 1.8 185 75 690 625 550 495 30 150 3.4 1.95 V V mA mA mW mW mW mW mW mW Static characteristics [1] Parameter Conditions Min Typ Max Unit Low Voltage Complementary Metal Oxide Semiconductor (LVCMOS) VIL VIH VIL VIH IIL IIH CI 0.7VDDA 0 0.7VDDA 10 50 4 0.3VDDA 0.3VDDA VDDA +10 +50 V V V V A A pF SPI: pins CS, SDIO, and SCLK ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 5 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 5. Symbol II RI CI VI(cm) Bi VI(dif) VO(cm) IO(cm) Static characteristics …continued[1] Parameter input current input resistance input capacitance common-mode input voltage input bandwidth differential input voltage common-mode output voltage common-mode output current voltage on pin VREF output input peak-to-peak Conditions track mode track mode track mode track mode Min 5 1.1 1 Typ 15 5 1.5 600 0.5VDDA 4 Max +5 2 2 Unit A  pF V MHz V V mA Analog inputs: pins INP and INM Voltage controlled regulator output: pin VCM Reference voltage input/output: pin VREF VVREF 0.5 0.5 1 1 V V Data outputs: CMLP, CMLN Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 000 VOL VOH LOW-level output voltage HIGH-level output voltage DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled DC-coupled; output AC-coupled 1.5 1.35 1.8 1.65 1.45 1.275 1.8 1.625 1.4 1.2 1.8 1.6 1.35 1.125 1.8 1.575 1.3 1.05 1.8 1.55 V V V V V V V V V V V V V V V V V V V V © NXP B.V. 2011. All rights reserved. Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 001 VOL VOH LOW-level output voltage HIGH-level output voltage Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 010 VOL VOH LOW-level output voltage HIGH-level output voltage Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 011 VOL VOH LOW-level output voltage HIGH-level output voltage Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 100 VOL VOH LOW-level output voltage HIGH-level output voltage ADC1413S_SER All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 2 — 8 June 2011 6 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 5. Symbol VIL VIH Accuracy INL DNL Eoffset EG Supply PSRR Static characteristics …continued[1] Parameter LOW-level input voltage Conditions differential; input Min 5 guaranteed no missing codes full-scale 200 mV (p-p) on pin VDDA; fi = DC 0.95 Typ 0.95 1.47 0.5 2  0.5 54 Max +5 +0.95 Unit V V LSB LSB mV % dB Serial configuration: SYNCP, SYNCN HIGH-level input voltage differential; input integral non-linearity differential non-linearity offset error gain error power supply rejection ratio [1] Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 7 of 38 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx 10. Dynamic characteristics 10.1 Dynamic characteristics Table 6. Symbol 2H Dynamic characteristics [1] Parameter second harmonic level Conditions fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz 3H third harmonic level fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz THD total harmonic distortion fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz ENOB effective number of bits fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz SNR signal-to-noise ratio fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz SFDR spurious-free dynamic range fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz ADC1413S065 Min Typ 87 86 85 82 86 85 84 81 83 82 81 78 11.7 11.6 11.5 11.4 72.1 71.3 70.7 70.2 86 85 84 81 Max ADC1413S080 Min Typ 87 86 85 82 86 85 84 81 83 82 81 78 11.7 11.5 11.5 11.4 72.0 71.2 70.7 70.1 86 85 84 81 Max ADC1413S105 Min Typ 86 86 84 81 85 85 83 80 82 82 80 77 11.6 11.5 11.4 11.3 71.8 71.2 70.6 70.0 85 85 83 80 Max ADC1413S125 Min Typ 88 87 85 83 87 86 84 82 84 83 81 79 11.6 11.5 11.4 11.3 71.4 71.1 70.5 69.9 87 86 84 82 Max dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc Unit Product data sheet Rev. 2 — 8 June 2011 8 of 38 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. NXP Semiconductors Single 14-bit ADC: serial JESD204A interface bits bits bits bits dBFS dBFS dBFS dBFS dBc dBc dBc dBc ADC1413S series xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 6. Symbol IMD Dynamic characteristics …continued[1] Parameter intermodulation distortion Conditions fi = 3 MHz fi = 30 MHz fi = 70 MHz fi = 170 MHz ct(ch) [1] Product data sheet Rev. 2 — 8 June 2011 9 of 38 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. NXP Semiconductors ADC1413S065 Min Typ 89 88 87 84 100 Max - ADC1413S080 Min Typ 89 88 87 85 100 Max - ADC1413S105 Min Typ 88 88 86 83 100 Max - ADC1413S125 Min Typ 89 88 86 84 100 Max - Unit dBc dBc dBc dBc dBc channel crosstalk fi = 70 MHz Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C and CL = 5 pF. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. 10.2 Clock and digital output timing Table 7. Symbol Clock and digital output timing characteristics [1] Parameter Conditions ADC1413S065 Min pins CLKP and CLKM fclk tlat(data) clk td(s) twake [1] ADC1413S080 Min 60 250 30 Typ 50 0.8 76 Max 80 283 70 - ADC1413S105 Min 75 190 30 Typ 50 0.8 76 Max 105 226 70 - ADC1413S125 Min 100 160 30 Typ 50 0.8 76 Max 125 170 70 - Unit Typ 50 0.8 76 Max 65 850 70 - clock frequency data latency time clock duty cycle sampling delay time wake-up time clock cycles DCS_EN = 1: en 45 307 30 - Msps ns % ns ns Single 14-bit ADC: serial JESD204A interface ADC1413S series Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 10.3 Serial output timing The eye diagram of the serial output is shown in Figure 3 and Figure 4. Test conditions are: • 3.125 Gbps data rate • Tamb = 25 °C • DC-coupling with two different receiver common-mode voltages 005aaa088 Fig 3. Eye diagram at 1 V receiver common-mode 005aaa089 Fig 4. Eye diagram at 2 V receiver common-mode ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 10 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 10.4 SPI timing Table 8. Symbol tw(SCLK) tw(SCLKH) tw(SCLKL) tsu SPI timing characteristics [1] Parameter SCLK pulse width SCLK HIGH pulse width SCLK LOW pulse width set-up time data to SCLK HIGH CS to SCLK HIGH th hold time data to SCLK HIGH CS to SCLK HIGH fclk(max) [1] Conditions Min - Typ 40 16 16 5 5 2 2 25 Max - Unit ns ns ns ns ns ns ns MHz maximum clock frequency Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. tsu CS th tsu tw(SCLKL) tw(SCLK) tw(SCLKH) th SCLK SDIO R/W W1 W0 A12 A11 D2 D1 D0 005aaa065 Fig 5. SPI timing ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 11 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 11. Application information 11.1 Analog inputs 11.1.1 Input stage description The analog input of the ADC1413S supports a differential or a single-ended input drive. Optimal performance is achieved using differential inputs with the common-mode input voltage (VI(cm)) on pins INP and INM set to 0.5VDDA. The full-scale analog input voltage range is configurable between 1 V (p-p) and 2 V (p-p) via a programmable internal reference (see Section 11.2 and Table 21). Figure 6 shows the equivalent circuit of the sample-and-hold input stage, including ElectroStatic Discharge (ESD) protection and circuit and package parasitics. package ESD parasitics switch INP 8 Ron = 15 Ω Cs internal clock switch Ron = 15 Ω INM 7 Cs internal clock 005aaa185 Fig 6. Input sampling circuit The sample phase occurs when the internal clock (derived from the clock signal on pin CLKP/CLKM) is HIGH. The voltage is then held on the sampling capacitors. When the clock signal goes LOW, the stage enters the hold phase and the voltage information is transmitted to the ADC core. ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 12 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 11.1.2 Anti-kickback circuitry Anti-kickback circuitry (RC filter in Figure 7) is needed to counteract the effects of a charge injection generated by the sampling capacitance. The RC filter is also used to filter noise from the signal before it reaches the sampling stage. The value of the capacitor should be chosen to maximize noise attenuation without degrading the settling time excessively. R INP C R INM 005aaa073 Fig 7. Anti-kickback circuit The component values are determined by the input frequency and should be selected so as not to affect the input bandwidth. Table 9. RC coupling versus input frequency, typical values Resistance () 25 12 12 Capacitance (pF) 12 8 8 3 70 170 Input frequency (MHz) 11.1.3 Transformer The configuration of the transformer circuit is determined by the input frequency. The configuration shown in Figure 8 would be suitable for a baseband application. ADT1-1WT 100 nF analog input 100 nF 25 Ω 25 Ω INP 12 pF 100 nF 25 Ω 25 Ω 100 nF INM VCM 100 nF 100 nF 005aaa044 Fig 8. Single transformer configuration ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 13 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface The configuration shown in Figure 9 is recommended for high frequency applications. In both cases, the choice of transformer is a compromise between cost and performance. ADT1-1WT 100 nF 50 Ω ADT1-1WT 50 Ω 12 Ω INP analog input 8.2 pF 50 Ω 50 Ω 12 Ω INM VCM 100 nF 100 nF 100 nF 005aaa045 Fig 9. Dual transformer configuration 11.2 System reference and power management 11.2.1 Internal/external reference The ADC1413S has a stable and accurate built-in internal reference voltage to adjust the ADC full-scale. This reference voltage can be set internally via SPI or with pins VREF and SENSE (see Figure 11 to Figure 14), in 1 dB steps between 0 dB and 6 dB, via SPI control bits INTREF[2:0] (when bit INTREF_EN = logic 1; see Table 21). The equivalent reference circuit is shown in Figure 10. External reference is also possible by providing a voltage on pin VREF as described in Figure 14. ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 14 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface REFT REFERENCE AMP REFB VREF EXT_ref BUFFER EXT_ref BANDGAP REFERENCE ADC CORE SENSE SELECTION LOGIC 005aaa164 Fig 10. Reference equivalent schematic Table 10 shows how to choose between the different internal/external modes: Table 10. Mode Internal (Figure 11) Internal (Figure 12) Internal, SPI mode (Figure 13) External (Figure 14) Reference modes SPI bit, “Internal reference” 0 0 1 0 SENSE pin GND VREF pin Full-scale, (V (p-p)) 330 pF capacitor 2 to GND 1 1 to 2 VREF pin = SENSE pin and 330 pF capacitor to GND VREF pin = SENSE pin and 330 pF capacitor to GND VDDA External voltage 1 to 2 from 0.5 V to 1 V Figure 11 to Figure 14 illustrate how to connect the SENSE and VREF pins to select the required reference voltage source. ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 15 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface VREF 330 pF VREF 330 pF REFERENCE EQUIVALENT SCHEMATIC REFERENCE EQUIVALENT SCHEMATIC SENSE SENSE 005aaa116 005aaa117 Fig 11. Internal reference, 2 V (p-p) full-scale Fig 12. Internal reference, 1 V (p-p) full-scale VREF VREF 0.1 μF 330 pF REFERENCE EQUIVALENT SCHEMATIC SENSE V REFERENCE EQUIVALENT SCHEMATIC SENSE 005aaa118 VDDA 005aaa119 Fig 13. Internal reference via SPI, 1 V (p-p) to 2 V (p-p) full-scale Fig 14. External reference, 1 V (p-p) to 2 V (p-p) full-scale 11.2.2 Programmable full-scale The full-scale is programmable between 1 V (p-p) to 2 V (p-p) (see Table 11). Table 11. 000 001 010 011 100 101 110 111 Reference modes Level 0 dB 1 dB 2 dB 3 dB 4 dB 5 dB 6 dB not used Full-scale (V (p-p)) 2 1.78 1.59 1.42 1.26 1.12 1 x INTREF[2:0] ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 16 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 11.2.3 Common-mode output voltage (VO(cm)) An 0.1 F filter capacitor should be connected between pin VCM and ground to ensure a low-noise common-mode output voltage. When AC-coupled, these pins can be used to set the common-mode reference for the analog inputs, for instance via a transformer middle point. package ESD parasitics COMMON-MODE REFERENCE 1.5 V VCM 0.1 μF ADC core 005aaa051 Fig 15. Reference equivalent schematic 11.2.4 Biasing The common-mode input voltage (VI(cm)) on pins INP and INM should be set externally to 0.5VDDA for optimal performance and should always be between 0.9 V and 2 V. 11.3 Clock input 11.3.1 Drive modes The ADC1413S can be driven differentially (LVPECL). It can also be driven by a single-ended LVCMOS signal connected to pin CLKP (CLKM should be connected to ground via a capacitor). LVCMOS clock input CLKP CLKP CLKM LVCMOS clock input CLKM 005aaa174 005aaa053 a. Rising edge LVCMOS Fig 16. LVCMOS single-ended clock input b. Falling edge LVCMOS ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 17 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface CLKP Sine clock input Sine clock input CLKP CLKM CLKM 005aaa173 005aaa054 a. Sine clock input b. Sine clock input (with transformer) CLKP LVPECL clock input CLKM 005aaa172 c. LVPECL clock input Fig 17. Differential clock input 11.3.2 Equivalent input circuit The equivalent circuit of the input clock buffer is shown in Figure 18. The common-mode voltage of the differential input stage is set via internal 5 k resistors. package ESD parasitics CLKP Vcm(clk) SE_SEL SE_SEL 5 kΩ 5 kΩ CLKM 005aaa081 Vcm(clk) = common-mode voltage of the differential input stage. Fig 18. Equivalent input circuit ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 18 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Single-ended or differential clock inputs can be selected via the SPI (see Table 20). If single-ended is selected, the input pin (CLKM or CLKP) is selected via control bit SE_SEL. If single-ended is implemented without setting bit SE_SEL accordingly, the unused pin should be connected to ground via a capacitor. 11.3.3 Duty cycle stabilizer The duty cycle stabilizer can improve the overall performance of the ADC by compensating the input clock signal duty cycle. When the duty cycle stabilizer is active (bit DCS_EN = logic 1; see Table 20), the circuit can handle signals with duty cycles of between 30 % and 70 % (typical). When the duty cycle stabilizer is disabled (DCS_EN = logic 0), the input clock signal should have a duty cycle of between 45 % and 55 %. Table 12. 0 1 Duty cycle stabilizer Description duty cycle stabilizer disable duty cycle stabilizer enable bit DCS_EN 11.3.4 Clock input divider The ADC1413S contains an input clock divider that divides the incoming clock by a factor of 2 (when bit CLKDIV2_SEL = logic 1; see Table 20). This feature allows the user to deliver a higher clock frequency with better jitter performance, leading to a better SNR result once acquisition has been performed. 11.4 Digital outputs 11.4.1 Serial output equivalent circuit The JESD204A standard specifies that if the receiver and the transmitter are DC-coupled both must be fed from the same supply. VDDD VDDD 50 Ω 50 Ω CMLP 100 Ω RECEIVER CMLN + 12 mA to 26 mA AGND 005aaa197 Fig 19. CML output connection to the receiver (DC-coupling) The output should be terminated when 100  (typical) is reached at the receiver side. ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 19 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface VDDD 50 Ω 50 Ω CMLP 10 nF 100 Ω RECEIVER CMLN + 12 mA to 26 mA 10 nF 005aaa187 Fig 20. CML output connection to the receiver (AC-coupling) 11.5 JESD204A serializer For more information about the JESD204A standard refer to the JEDEC web site. 11.5.1 Digital JESD204A formatter The block placed after the ADC cores is used to implement all functions of the JESD204A standard. This ensures signal integrity and guarantees the clock and the data recovery at the receiver side. The block is highly parameterized and can be configured in various ways depending on the sampling frequency and the number of lanes used. M CONVERTERS N bits from Cr0 + CS bits for control L LANES F octets TX transport layer FRAME TO OCTETS SCRAMBLER ALIGNMENT CHARACTER GENERATOR 8-bit/ 10-bit SER LANE 0 SYNC~ TX CONTROLLER N' = N + CS S samples per frame cycle CF: position of controls bits HD: frame boundary break Padding with Tails bits (TT) L × (F) octets L octets 005aaa198 M × (N' × S) bits Fig 21. General overview of the JESD204A serializer ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 20 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface ADC_MODE[1:0] SCR_IN_MODE N AND CS LANE_MODE[1:0] N + CS 8 00 SCR PRBS FSM (frame assembly, character replication, ILA, test mode) 01 8-bit/ 10-bit '0' 10 00 PRBS 11 DUMMY 14 + 1 10 14 + 1 ADC_PD LANE_POL SER 01 ADC 14 + 1 00 FRAME ASSEMBLY '0/1' PRBS 10 11 ×1 PLL AND DLL frame CLK character CLK bit CLK SWING_SEL[2:0] ×F × 10F sync_request 005aaa199 Fig 22. Detailed view of the JESD204A serializer with debug functionality 11.5.2 ADC core output codes versus input voltage Table 13 shows the data output codes for a given analog input voltage. Table 13. < 1 1 0.9998779 0.9997559 0.9996338 0.9995117 .... 0.0002441 0.0001221 0 +0.0001221 +0.0002441 .... +0.9995117 +0.9996338 +0.9997559 +0.9998779 +1 > +1 Output codes versus input voltage Offset binary 00 0000 0000 0000 00 0000 0000 0000 00 0000 0000 0001 00 0000 0000 0010 00 0000 0000 0011 00 0000 0000 0100 .... 01 1111 1111 1110 01 1111 1111 1111 10 0000 0000 0000 10 0000 0000 0001 10 0000 0000 0010 .... 11 1111 1111 1011 11 1111 1111 1100 11 1111 1111 1101 11 1111 1111 1110 11 1111 1111 1111 11 1111 1111 1111 Two’s complement 10 0000 0000 0000 10 0000 0000 0000 10 0000 0000 0001 10 0000 0000 0010 10 0000 0000 0011 10 0000 0000 0100 .... 11 1111 1111 1110 11 1111 1111 1111 00 0000 0000 0000 00 0000 0000 0001 00 0000 0000 0010 .... 01 1111 1111 1011 01 1111 1111 1100 01 1111 1111 1101 01 1111 1111 1110 01 1111 1111 1111 01 1111 1111 1111 OTR 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 INP-INM (V) ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 21 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 11.6 Serial Peripheral Interface (SPI) 11.6.1 Register description The ADC1413S serial interface is a synchronous serial communications port allowing easy interfacing with many industry microprocessors. It provides access to the registers that control the operation of the chip in both read and write modes. This interface is configured as a 3-wire type (SDIO as bidirectional pin). Pin SCLK acts as the serial clock and pin CS acts as the serial chip select. Each read/write operation is sequenced by the CS signal and enabled by a LOW level to to drive the chip with N bytes, depending on the content of the instruction byte (see Table 14). Table 14. Bit Description Instruction bytes for the SPI MSB 7 R/W[1] A7 [1] LSB 6 W1 A6 5 W0 A5 4 A12 A4 3 A11 A3 2 A10 A2 1 A9 A1 0 A8 A0 R/W indicates whether a read or write transfer occurs after the instruction byte. Table 15. R/W[1] 0 1 [1] Read or Write mode access description Description Write mode operation Read mode operation Bits W1 and W0 indicate the number of bytes transferred. ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 22 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Number of bytes to be transferred W0 0 1 0 1 Number of bytes transferred 1 byte 2 bytes 3 bytes 4 or more bytes Table 16. W1 0 0 1 1 Bits A12 to A0 indicate the address of the register being accessed. In the case of a multiple byte transfer, this address is the first register to be accessed. An address counter is incremented to access subsequent addresses. The steps involved in a data transfer are as follows: 1. The falling edge on pin CS in combination with a rising edge on pin SCLK determine the start of communications. 2. The first phase is the transfer of the 2-byte instruction. 3. The second phase is the transfer of the data which can be vary in length but is always a multiple of 8 bits. The MSB is always sent first (for instruction and data bytes). 4. A rising edge on pin CS indicates the end of data transmission. CS SCLK SDIO R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Instruction bytes Register N (data) Register N + 1 (data) 005aaa086 Fig 23. Transfer diagram for two data bytes (3-wire type) ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 23 of 38 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx 11.6.2 Channel control Table 17. Register allocation map Access[1] Bit 7 R/W SW_RST Bit 6 Bit 5 Bit 4 SE_SEL Bit definition Bit 3 DIFF_SE INTREF_EN DIG_OFFSET[5:0] TESTPAT_2[13:6] TESTPAT_3[5:0] TESTPAT_1[2:0] Bit 2 Bit 1 ENABLE PD[1:0] CLKDIV2_SEL INTREF[2:0] DCS_EN Bit 0 Default[2] Bin Address Register name (hex) ADC control register 0003 0005 0006 0008 0013 0014 0015 0016 SPI control 1111 1111 0000 0000 0000 000* 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 Reset and R/W Operating modes Clock Vref Offset Test pattern 1 Test pattern 2 Test pattern 3 R/W R/W R/W R/W R/W R/W Product data sheet Rev. 2 — 8 June 2011 24 of 38 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. NXP Semiconductors JESD204A control Single 14-bit ADC: serial JESD204A interface 0801 0802 0805 Ser_Status Ser_Reset Ser_Control1 R R/W R/W RXSYNC_ ERROR SW_RST 0 0 RESERVED[2:0] 0 SYNC_ POL 0 0 SYNC_ SINGLE_ ENDED 0 0 FSM_SW_ RST 1 0 0 REV_ SCR POR_TST 0 REV_ ENCODER RESERVED 0100 0000 0 REV_ SERIAL 0000 0000 0100 1001 0000 0011 0000 0000 ADC1413S series RESERVED 0808 0809 Ser_Analog_Ctrl Ser_ScramblerA R/W R/W 0 0 0 0 LSB_INIT[6:0] SWING_SEL[2:0] xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 17. Register allocation map …continued Access[1] Bit 7 R/W R/W R R/W* R/W* R/W* R/W* R/W* R/W* R R/W* R/W* R/W* R/W R/W 0 SCR 0 0 0 0 0 0 HD 0 0 0 0 0 0 0 0 CS[0] 0 0 0 0 SCR_IN_ MODE 0 0 0 0 0 0 0 0 0 0 0 FCHK[7:0] LANE_MODE[1:0] ADC_MODE[1:0] 0 0 LANE_ POL 0 0 0 LANE_PD ADC_PD 0 0 0 0 0 0 NP[4:0] 0 0 LID[4:0] 0 CF[1:0] S 0 0 0 0 0 0 K[4:0] 0 N[3:0] 0 M 0 0 0 0 0 Bit 6 Bit 5 Bit 4 Bit definition Bit 3 MSB_INIT[7:0] 0 DID[7:0] BID[3:0] 0 F[2:0] L 0 PRBS_TYPE[1:0] Bit 2 Bit 1 Bit 0 Default[2] Bin 1111 1111 0000 0000 1110 1101 0000 1010 0000 0000 0000 0*** 000* **** 0000 000* 0100 0100 0000 1111 0000 0000 *000 0000 0001 1100 **** **** 0000 0000 0000 0000 Product data sheet Rev. 2 — 8 June 2011 25 of 38 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. NXP Semiconductors Address Register name (hex) 080A 080B 0820 0821 0822 0823 0824 0825 0826 0827 0828 0829 082D 084D 0871 0891 Ser_ScramblerB Ser_PRBS_Ctrl Cfg_0_DID Cfg_1_BID Cfg_3_SCR_L Cfg_4_F Cfg_5_K Cfg_6_M Cfg_7_CS_N Cfg_8_Np Cfg_9_S Cfg_10_HD_CF Cfg_02_2_LID Lane_0_Ctrl ADC_0_Ctrl Single 14-bit ADC: serial JESD204A interface Cfg02_13_FCHK R ADC1413S series [1] [2] an "*" in the Access column means that this register is subject to control access conditions in Write mode. an "*" in the Default column replaces a bit of which the value depends on the binary level of external pins (e.g. CFG[3:0], Swing[1:0], Scrambler). NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 11.6.3 Register description 11.6.3.1 ADC control registers Table 18. Register SPI control (address 0003h) Default values are highlighted. Bit 7 to 2 1 Symbol ENABLE Access R/W 0 1 0 1 Value 111111 Description not used ADC SPI control enable: ADC does not get the next SPI command ADC gets the next SPI command not used Table 19. Register Reset and Power-down mode (address 0005h) Default values are highlighted. Bit 7 Symbol SW_RST Access R/W 0 1 6 to 2 1 to 0 PD[1-0] R/W 00 01 10 11 Table 20. Register Clock (address 0006h) Default values are highlighted. Bit 7 to 5 4 Symbol SE_SEL Access R/W 0 1 3 DIFF_SE R/W 0 1 2 1 CLKDIV2_SEL R/W 0 1 0 DCS_EN R/W 0 1 0 Value 000 Description not used select SE clock input pin: select CLKM input select CLKP input differential/single-ended clock input select: fully differential single-ended not used select clock input divider by 2: disable enable duty cycle stabilizer enable: disable enable 00000 Value Description reset digital part: no reset performs a reset of the digital part not used Power-down mode: normal (power-up) full power-down sleep normal (power-up) ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 26 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 21. Register Vref (address 0008h) Default values are highlighted. Bit 7 to 4 3 Symbol INTREF_EN Access R/W 0 1 2 to 0 INTREF[2:0] R/W 000 001 010 011 100 101 110 111 Value 0000 Description not used enable internal programmable VREF mode: disable enable programmable internal reference: 0 dB (FS = 2 V) 1 dB (FS = 1.78 V) 2 dB (FS = 1.59 V) 3 dB (FS = 1.42 V) 4 dB (FS = 1.26 V) 5 dB (FS = 1.12 V) 6 dB (FS = 1 V) not used Table 22. Digital offset adjustment (address 0013h) Default values are highlighted. Register offset Decimal +31 ... 0 ... 32 DIG_OFFSET[5:0] 011111 ... 000000 ... 100000 +31 LSB ... 0 ... 32 LSB Table 23. Register Test pattern 1 (address 0014h) Default values are highlighted. Bit 7 to 3 2 to 0 Symbol TESTPAT_1[2:0] Access R/W 000 001 010 011 100 101 110 111 Value 00000 Description not used digital test pattern: off mid-scale  FS + FS toggle ‘1111..1111’/’0000..0000’ custom test pattern, to be written in register 0015h and 0016h ‘010101...’ ‘101010...’ ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 27 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 24. Register Test pattern 2 (address 0015h) Default values are highlighted. Bit 7 to 0 Symbol TESTPAT_2[13:6] Access R/W Value Description 00000000 custom digital test pattern (bit 13 to 6) Table 25. Register Test pattern 3 (address 0016h) Default values are highlighted. Bit 7 to 3 2 to 0 Symbol TESTPAT_3[5:0] Access R/W Value 00000 000 Description custom digital test pattern (bit 5 to 0) not used 11.6.4 JESD204A digital control registers Table 26. SER_Status (address 0801h) Default values are highlighted. Bit 7 6 to 4 3 to 2 1 0 Symbol RXSYNC_ERROR RESERVED[2:0] POR_TST RESERVED Access R/W Value 0 100 00 0 0 Description set to 1 when a synchronization error occurs reserved not used power-on-reset reserved Table 27. SER_Reset (address 0802h) Default values are highlighted. Bit 7 6 to 4 3 2 to 0 Symbol SW_RST FSM_SW_RST Access R/W R/W Value 0 000 0 000 Description initiates a software reset of the JEDEC204A unit not used initiates a software reset of the internal state machine of JEDEC204A unit not used Table 28. SER_Control1 (address 0805h) Default values are highlighted. Bit 7 6 5 Symbol RESERVED SYNC_POL Access R/W R/W 0 1 4 SYNC_SINGLE_ENDED R/W 0 1 3 2 REV_SCR 0 1 ADC1413S_SER Value 0 0 Description not used reserved defines the sync signal polarity: synchronization signal is active low synchronization signal is active high defines the input mode of the sync signal: synchronization input mode is set in Differential mode synchronization input mode is set in Single-ended mode not used LSB are swapped to MSB at the scrambler input: disable enable © NXP B.V. 2011. All rights reserved. 1 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 2 — 8 June 2011 28 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 28. SER_Control1 (address 0805h) …continued Default values are highlighted. Bit 1 Symbol REV_ENCODER Access 0 1 0 REV_SERIAL 0 1 Table 29. SER_Analog_Ctrl (address 0808h) Default values are highlighted. Bit 7 to 3 2 to 0 Symbol SWING_SEL[2:0] Access R/W Value 00000 011 Description not used defines the swing output for the lane pads Value Description LSB are swapped to MSB at the 8-bit/10-bit encoder input disable enable LSB are swapped to MSB at the lane input: disable enable Table 30. SER_ScramblerA (address 0809h) Default values are highlighted. Bit 7 6 to 0 Symbol LSB_INIT[6:0] Access R/W Value 0 0000000 Description not used defines the initialization vector for the scrambler polynomial (lower) Table 31. SER_ScramblerB (address 080Ah) Default values are highlighted. Bit 7 to 0 Symbol MSB_INIT[7:0] Access R/W Value 11111111 Description defines the initialization vector for the scrambler polynomial (upper) Table 32. SER_PRBS_Ctrl (address 080Bh) Default values are highlighted. Bit 7 to 2 1 to 0 Symbol PRBS_TYPE[1:0] Access R/W 00 (reset) 01 10 11 Table 33. Cfg_0_DID (address 0820h) Default values are highlighted. Bit 7 to 0 Symbol DID[7:0] Access R Value Description 11101101 defines the device (= link) identification number Value 000000 Description not used defines the type of Pseudo-Random Binary Sequence (PRBS) generator to be used: PRBS-7 PRBS-7 PRBS-23 PRBS-31 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 29 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 34. Cfg_1_BID (address 0821h) Default values are highlighted. Bit 7 to 4 3 to 0 Symbol BID[3:0] Access R/W Value 0000 1010 Description not used defines the bank ID – extension to DID Table 35. Cfg_3_SCR_L (address 0822h) Default values are highlighted. Bit 7 6 to 1 0 Symbol SCR L Access R/W R/W Value 0 000000 0 Description scrambling enabled not used defines the number of lanes per converter device, minus 1 Table 36. Cfg_4_F (address 0823h) Default values are highlighted. Bit 7 to 3 2 to 0 Symbol F[2:0] Access R/W Value 00000 *** Description not used defines the number of octets per frame, minus 1 Table 37. Cfg_5_K (address 0824h) Default values are highlighted. Bit 7 to 5 4 to 0 Symbol K[4:0] Access R/W Value 000 ***** Description not used defines the number of frames per multiframe, minus 1 Table 38. Cfg_6_M (address 0825h) Default values are highlighted. Bit 7 to 1 0 Symbol M Access R/W Value 0000000 * Description not used defines the number of converters per device, minus 1 Table 39. Cfg_7_CS_N (address 0826h) Default values are highlighted. Bit 7 6 5 to 4 3 to 0 Symbol CS[0] N[3:0] Access R/W R/W Value 0 1 00 0100 Description not used defines the number of control bits per sample, minus 1 not used defines the converter resolution Table 40. Cfg_8_Np (address 0827h) Default values are highlighted. Bit 7 to 5 4 to 0 Symbol NP[4:0] Access R/W Value 000 01111 Description not used defines the total number of bits per sample, minus 1 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 30 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 41. Cfg_9_S (address 0828h) Default values are highlighted. Bit 7 to 1 0 Symbol S Access R/W Value 0000000 0 Description not used defines number of samples per converter per frame cycle Table 42. Cfg_10_HD_CF (address 0829h) Default values are highlighted. Bit 7 6 to 2 1 to 0 Symbol HD CF[1:0] Access R/W R/W Value * 00000 00 Description defines high density format not used defines number of control words per frame clock cycle per link. Table 43. Cfg02_2_LID (address 082Dh) Default values are highlighted. Bit 7 to 5 4 to 0 Symbol LID[4:0] Access R/W Value 000 11100 Description not used defines lane identification number Table 44. Cfg01_13_FCHK (address 084Dh) Default values are highlighted. Bit 7 to 0 Symbol FCHK[7:0] Access R Value ******** Description defines the checksum value for lane checksum corresponds to the sum of all the link configuration parameters module 256 (as defined in JEDEC Standard No.204A) Table 45. Lane_0_Ctrl (address 0871h) Default values are highlighted. Bit 7 6 Symbol SCR_IN_MODE Access R/W 0 (reset) 1 Value 0 Description not used defines the input type for scrambler and 8-bit/10-bit units: (normal mode) = Input of the scrambler and 8-bit/10-bit units is the output of the frame assembly unit. input of the scrambler and 8-bit/10-bit units is the PRSB generator (PRBS type is defined with “PRBS_TYPE[1:0]” (Ser_PRBS_ctrl register) defines output type of Lane output unit: 00 (reset) 01 10 11 3 0 normal mode: Lane output is the 8-bit/10-bit output unit constant mode: Lane output is set to a constant (0  0) toggle mode: Lane output is toggling between 0  0 and 0  1 PRBS mode: Lane output is the PRBS generator (PRBS type is defined with “PRBS_TYPE[1:0]” (Ser_PRBS_ctrl register) not used 5 to 4 LANE_MODE[1:0] R/W ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 31 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface Table 45. Lane_0_Ctrl (address 0871h) …continued Default values are highlighted. Bit 2 Symbol LANE_POL Access R/W 0 1 1 0 RESERVED Lane_PD R/W R/W 0 1 Table 46. ADC_0_Ctrl (address 0891h) Default values are highlighted. Bit 7 to 6 5 to 4 Symbol ADC_MODE[1:0] Access R/W 00 (reset) 01 10 11 3 to 1 0 ADC_PD R/W 0 1 000 Value 00 Description not used defines input type of JESD204A unit ADC output is connected to the JESD204A input not used JESD204A input is fed with a dummy constant, set to: OTR = 0 and ADC[13:0] = “10011011101010” JESD204A is fed with a PRBS generator (PRBS type is defined with “PRBS_TYPE[1:0]” (Ser_PRBS_ctrl register) not used ADC power-down control: ADC is operational ADC is in Power-down mode 0 Value Description defines lane polarity: lane polarity is normal lane polarity is inverted reserved lane power-down control: lane is operational lane is in Power-down mode ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 32 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 12. Package outline HVQFN32R: plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; resin based; body 7 x 7 x 0.8 mm SOT1152-1 D B A terminal 1 index area E A detail X e1 e L1 9 L 8 17 b 1/2 e 16 ∅v ∅w CAB C y1 C C y Eh 1/2 e 1 terminal 1 index area 32 Dh 0 Dimensions Unit mm A b D 7.1 7.0 6.9 Dh 4.05 4.00 3.95 E 7.1 7.0 6.9 Eh e e1 e2 L 2.5 scale 25 24 e e2 X 5 mm L1 v 0.1 w y y1 0.1 max 0.90 0.28 nom 0.80 0.23 min 0.75 0.18 4.05 0.55 0.10 4.00 0.65 4.55 4.55 0.50 0.05 3.95 0.45 0.00 0.05 0.08 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included Outline version SOT1152-1 References IEC --JEDEC --JEITA --European projection sot1152-1_po Issue date 09-10-13 09-11-16 Fig 24. Package outline SOT1152-1 (HVQFN32) ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 33 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 13. Abbreviations Table 47. Acronym ADC DCS ESD IF IMD LSB LVCMOS LVPECL MSB OTR PRBS SFDR SNR SPI TX Abbreviations Description Analog-to-Digital Converter Duty Cycle Stabilizer ElectroStatic Discharge Intermediate Frequency InterModulation Distortion Least Significant Bit Low-Voltage Complementary Metal-Oxide Semiconductor Low-Voltage Positive Emitter-Coupled Logic Most Significant Bit OuT-of-Range Pseudo-Random Binary Sequence Spurious-Free Dynamic Range Signal-to-Noise Ratio Serial Peripheral Interface Transmitter ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 34 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 14. Revision history Table 48. Revision history Release date 20110608 Data sheet status Product data sheet Product data sheet Change notice Supersedes ADC1413S_SER v.1 Document ID ADC1413S_SER v.2 Modifications: ADC1413S_SER v.1 • Section 10.2 “Clock and digital output timing” has been updated. 20110314 ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 35 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 15. Legal information 15.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term ‘short data sheet’ is explained in section “Definitions”. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 15.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. © NXP B.V. 2011. All rights reserved. 15.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or ADC1413S_SER All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 2 — 8 June 2011 36 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond 15.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com ADC1413S_SER All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 — 8 June 2011 37 of 38 NXP Semiconductors ADC1413S series Single 14-bit ADC: serial JESD204A interface 17. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 Thermal characteristics . . . . . . . . . . . . . . . . . . 5 9 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 10 Dynamic characteristics . . . . . . . . . . . . . . . . . . 8 10.1 Dynamic characteristics . . . . . . . . . . . . . . . . . . 8 10.2 Clock and digital output timing . . . . . . . . . . . . . 9 10.3 Serial output timing . . . . . . . . . . . . . . . . . . . . . 10 10.4 SPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 Application information. . . . . . . . . . . . . . . . . . 12 11.1 Analog inputs . . . . . . . . . . . . . . . . . . . . . . . . . 12 11.1.1 Input stage description . . . . . . . . . . . . . . . . . . 12 11.1.2 Anti-kickback circuitry . . . . . . . . . . . . . . . . . . . 13 11.1.3 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . 13 11.2 System reference and power management . . 14 11.2.1 Internal/external reference . . . . . . . . . . . . . . . 14 11.2.2 Programmable full-scale . . . . . . . . . . . . . . . . . 16 11.2.3 Common-mode output voltage (VO(cm)) . . . . . 17 11.2.4 Biasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 11.3 Clock input . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 11.3.1 Drive modes . . . . . . . . . . . . . . . . . . . . . . . . . . 17 11.3.2 Equivalent input circuit . . . . . . . . . . . . . . . . . . 18 11.3.3 Duty cycle stabilizer . . . . . . . . . . . . . . . . . . . . 19 11.3.4 Clock input divider . . . . . . . . . . . . . . . . . . . . . 19 11.4 Digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . 19 11.4.1 Serial output equivalent circuit . . . . . . . . . . . . 19 11.5 JESD204A serializer. . . . . . . . . . . . . . . . . . . . 20 11.5.1 Digital JESD204A formatter . . . . . . . . . . . . . . 20 11.5.2 ADC core output codes versus input voltage . 21 11.6 Serial Peripheral Interface (SPI) . . . . . . . . . . . 22 11.6.1 Register description . . . . . . . . . . . . . . . . . . . . 22 11.6.2 Channel control . . . . . . . . . . . . . . . . . . . . . . . 24 11.6.3 Register description . . . . . . . . . . . . . . . . . . . . 26 11.6.3.1 ADC control registers . . . . . . . . . . . . . . . . . . . 26 11.6.4 JESD204A digital control registers . . . . . . . . . 28 12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 33 13 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 34 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 35 15 15.1 15.2 15.3 15.4 16 17 Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 36 36 36 37 37 38 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 8 June 2011 Document identifier: ADC1413S_SER