N74F00N,602

Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic and PowerMOS semiconductors with its focus on the automotive, industrial, computing, consumer and wearable application markets In data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below. Instead of http://www.nxp.com, http://www.philips.com/ or http://www.semiconductors.philips.com/, use http://www.nexperia.com Instead of sales.addresses@www.nxp.com or sales.addresses@www.semiconductors.philips.com, use salesaddresses@nexperia.com (email) Replace the copyright notice at the bottom of each page or elsewhere in the document, depending on the version, as shown below: - © NXP N.V. (year). All rights reserved or © Koninklijke Philips Electronics N.V. (year). All rights reserved Should be replaced with: - © Nexperia B.V. (year). All rights reserved. If you have any questions related to the data sheet, please contact our nearest sales office via e-mail or telephone (details via salesaddresses@nexperia.com). Thank you for your cooperation and understanding, Kind regards, Team Nexperia INTEGRATED CIRCUITS 74F06 Inverter/buffer drivers Product data Supersedes data of 1992 Jul 24 
   2004 Mar 12 Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) FEATURES • Open Collector output drive 64mA • High speed • 12V output termination voltage TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F06 3.5ns 30mA ORDERING INFORMATION TYPE NUMBER PKG DWG # 14-pin plastic dual in-line package DESCRIPTION N74F06N SOT27–1 14-pin plastic small outline package N74F06D SOT108–1 PIN CONFIGURATIONS 74F06 A0 1 14 VCC Y0 2 13 A5 A1 3 12 Y5 Y1 4 11 A4 A2 5 10 Y4 Y2 6 9 A3 GND 7 8 Y3 SF00016 LOGIC SYMBOLS 74F06 1 3 5 9 11 13 A0 A1 A2 Y0 Y1 Y2 Y3 Y4 Y5 2 4 6 A3 A4 A5 8 10 12 VCC = Pin 14 GND = Pin 7 SF00018 2004 Mar 12 2 Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) IEC/IEEE SYMBOLS 74F06 1 2 3 4 5 6 9 8 11 10 13 12 SF00020 LOGIC DIAGRAMS 74F06 A0 A1 A2 A3 A4 VCC = Pin 14 GND = Pin 7 A5 1 2 3 4 5 6 9 8 11 10 13 12 Y0 Y1 Y2 Y3 Y4 Y5 SF00022 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION An Data inputs Yn Data outputs NOTES: 1. One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. 2. OC = Open Collector FUNCTION TABLE INPUTS OUTPUTS An Yn L H H L NOTES: 1. H = High voltage level 2. L = Low voltage level 2004 Mar 12 3 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW 1.0/1.0 20µA/0.6mA OC/106.7 OC/64mA Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) RATING UNIT VCC Supply voltage PARAMETER –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to 12 V IOUT Current applied to output in Low output state 128 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C SYMBOL RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL LIMITS UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 V VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIk V Input clamp current –18 mA VOH High-level output voltage 12 V IOL Low-level output current 64 mA +70 °C Tamb 2004 Mar 12 Operating free air temperature range 0 4 Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL TEST CONDITIONS1 PARAMETER LIMITS MIN TYP2 UNIT MAX 250 µA 0.30 0.50 V 0.30 0.50 V –0.73 –1.2 V 100 µA IOH High-level output current VCC = MIN, VIL = MAX, VOH = MAX, VIH = MIN VOL Low-level output voltage VCC = MIN, VIL = MAX, VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage VCC = MAX, VI = 7.0V IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA ICC Supply current (total) 5.0 8.0 mA 30 43 mA ±10% VCC IOL = MAX ±5% VCC VIH = MIN ICCH VCC = MAX ICCL NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL tPLH tPHL 2004 Mar 12 PARAMETER Propagation delay An to Yn TEST CONDITION Waveform 1 VCC = +5.0V Tamb = +25°C CL = 50pF, RL = 100Ω VCC = +5.0V ± 10% Tamb = 0°C to +70°C CL = 50pF, RL = 100Ω Min Typ Max Min Max 2.0 1.5 3.5 3.0 6.0 5.5 1.5 1.0 6.5 6.0 5 UNIT ns Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) TYPICAL PROPAGATION DELAYS VERSUS LOAD FOR OPEN COLLECTOR OUTPUTS 18 16 14 Propagation delay (ns) 12 10 8 tPLH 6 4 tPHL 2 0 0 100 200 300 400 500 600 Load resistor (Ω) SF00024 NOTE: When using Open-Collector parts, the value of the pull-up resistor greatly affects the value of the tPLH. For example, changing the specified pull-up resistor value from 500Ω to 100Ω will improve the tPLH up to 50% with only a slight increase in the tPHL. However, if the value of the pull-up resistor is changed, the user must make certain that the total IOL current through the resistor and the total IIL’s of the receivers does not exceed the IOL maximum specification. 2004 Mar 12 6 Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) AC WAVEFORMS An VM VM tPHL tPLH VM Yn VM SF00025 Waveform 1. Propagation delay for inverting outputs NOTE: For all waveforms, VM = 1.5V. TEST CIRCUIT AND WAVEFORMS 7.0V VCC tw 90% VIN RL VOUT PULSE GENERATOR NEGATIVE PULSE VM CL AMP (V) VM 10% D.U.T. RT 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V RL AMP (V) 90% 90% Test Circuit for Open Collector Outputs POSITIVE PULSE VM VM 10% DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. 10% tw 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns SF00027 2004 Mar 12 7 Philips Semiconductors Product data Hex inverter/buffer drivers (open-collector) DIP14: plastic dual in-line package; 14 leads (300 mil) 2004 Mar 12 8 74F06 SOT27-1 Philips Semiconductors Product data Hex inverter/buffer drivers (open-collector) SO14: plastic small outline package; 14 leads; body width 3.9 mm 2004 Mar 12 9 74F06 SOT108-1 Philips Semiconductors Product data Hex inverter/buffer drivers (open-collector) 74F06 REVISION HISTORY Rev Date Description _3 20040312 Product data (9397 750 13034); supersedes data sheet 74F06_A_7_A_2 of 1992 Jul 24 (9397 750 05054). Modifications: • Delete all references to 74F06A and 74F07A (product discontinued). • Separate 74F06 and 74F07 into standalone data sheets. _2 19920724 2004 Mar 12 Product data (9397 750 05054); supersedes previous version. 10 Philips Semiconductors Product data 74F06 Hex inverter/buffer drivers (open-collector) Data sheet status Level Data sheet status [1] Product status [2] [3] Definitions I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes in the products—including circuits, standard cells, and/or software—described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.  Koninklijke Philips Electronics N.V. 2004 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 03-04 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. Document order number: 
   2004 Mar 12 11 9397 750 13034