0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
PCA9542AD,118

PCA9542AD,118

  • 厂商:

    NXP(恩智浦)

  • 封装:

    SOIC14

  • 描述:

    IC I2C MUX 2CH 14-SOIC

  • 数据手册
  • 价格&库存
PCA9542AD,118 数据手册
PCA9542A 2-channel I2C-bus multiplexer and interrupt logic Rev. 5.1 — 15 July 2015 Product data sheet 1. General description The PCA9542A is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus. The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels. Only one SCx/SDx channel is selected at a time, determined by the contents of the programmable control register. Two interrupt inputs, INT0 and INT1, one for each of the SCx/SDx downstream pairs, are provided. One interrupt output, INT, which acts as an AND of the two interrupt inputs, is provided. A power-on reset function puts the registers in their default state and initializes the I2C-bus state machine with no channels selected. The pass gates of the multiplexer are constructed such that the VDD pin can be used to limit the maximum high voltage which will be passed by the PCA9542A. This allows the use of different bus voltages on each SCx/SDx pair, so that 1.8 V, 2.5 V, or 3.3 V parts can communicate with 5 V parts without any additional protection. External pull-up resistors pull the bus up to the desired voltage level for each channel. All I/O pins are 5 V tolerant. 2. Features and benefits                 1-of-2 bidirectional translating multiplexer I2C-bus interface logic; compatible with SMBus 2 active LOW interrupt inputs (INT0, INT1) Active LOW interrupt output (INT) 3 address pins allowing up to 8 devices on the I2C-bus Channel selection via I2C-bus Powers up with all multiplexer channels deselected Low Ron switches Allows voltage level translation between 1.8 V, 2.5 V, 3.3 V and 5 V buses No glitch on power-up Supports hot insertion Low standby current Operating power supply voltage range of 2.3 V to 5.5 V 5 V tolerant inputs 0 Hz to 400 kHz clock frequency ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101  Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA  Packages offered: SO14, TSSOP14 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 3. Ordering information Table 1. Ordering information Type number Topside marking Package Name Description Version PCA9542AD PCA9542AD SO14 plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 PCA9542APW PA9542A TSSOP14 plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1 3.1 Ordering options Table 2. Ordering options Type number Orderable part number Package Packing method PCA9542AD PCA9542AD,112 SO14 Standard marking 1140 *IC’s tube - DSC bulk pack Tamb = 40 C to +85 C PCA9542AD,118 SO14 Reel 13” Q1/T1 *Standard mark SMD 2500 Tamb = 40 C to +85 C PCA9542APW,112 TSSOP14 Standard marking 2400 *IC’s tube - DSC bulk pack Tamb = 40 C to +85 C PCA9542APW,118 TSSOP14 Reel 13” Q1/T1 *Standard mark SMD Tamb = 40 C to +85 C PCA9542APW PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 Minimum order quantity 2500 Temperature range © NXP Semiconductors N.V. 2015. All rights reserved. 2 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 4. Block diagram PCA9542A SC0 SC1 SD0 SD1 VSS VDD SCL SDA SWITCH CONTROL LOGIC POWER-ON RESET INPUT FILTER A0 I2C-BUS CONTROL A1 A2 INT[1:0] INT INTERRUPT LOGIC 002aae303 Fig 1. PCA9542A Product data sheet Block diagram of PCA9542A All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 3 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 5. Pinning information 5.1 Pinning A0 1 14 VDD A1 2 13 SDA A2 3 12 SCL INT0 4 SD0 5 A0 1 14 VDD A1 2 13 SDA A2 3 INT0 4 SD0 5 10 SC1 SC0 6 9 SD1 VSS 7 8 INT1 PCA9542AD 11 INT 10 SC1 SC0 6 9 SD1 VSS 7 8 INT1 Pin configuration for SO14 11 INT 002aae302 002aae301 Fig 2. 12 SCL PCA9542APW Fig 3. Pin configuration for TSSOP14 5.2 Pin description Table 3. PCA9542A Product data sheet Pin description Symbol Pin Description A0 1 address input 0 A1 2 address input 1 A2 3 address input 2 INT0 4 active LOW interrupt input 0 SD0 5 serial data 0 SC0 6 serial clock 0 VSS 7 supply ground INT1 8 active LOW interrupt input 1 SD1 9 serial data 1 SC1 10 serial clock 1 INT 11 active LOW interrupt output SCL 12 serial clock line SDA 13 serial data line VDD 14 supply voltage All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 4 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 6. Functional description Refer to Figure 1 “Block diagram of PCA9542A”. 6.1 Device addressing Following a START condition the bus master must output the address of the slave it is accessing. The address of the PCA9542A is shown in Figure 4. To conserve power, no internal pull-up resistors are incorporated on the hardware selectable address pins and they must be pulled HIGH or LOW. 1 1 1 0 fixed A2 A1 A0 R/W hardware selectable 002aab189 Fig 4. Slave address The last bit of the slave address defines the operation to be performed. When set to logic 1 a read is selected, while a logic 0 selects a write operation. 6.2 Control register Following the successful acknowledgement of the slave address, the bus master will send a byte to the PCA9542A which will be stored in the control register. If multiple bytes are received by the PCA9542A, it will save the last byte received. This register can be written and read via the I2C-bus. interrupt bits (read only) bit 7 6 X X 5 4 INT1 INT0 writable, but always read 0 Fig 5. channel selection bits (read/write) 3 2 1 0 X B2 B1 B0 enable bit 002aae304 Control register 6.2.1 Control register definition A SCx/SDx downstream pair, or channel, is selected by the contents of the control register. This register is written after the PCA9542A has been addressed. The 3 LSBs of the control byte are used to determine which channel is to be selected. When a channel is selected, it will become active after a STOP condition has been placed on the I2C-bus. This ensures that all SCx/SDx lines will be in a HIGH state when the channel is made active, so that no false conditions are generated at the time of connection. Bits INT0, INT1, D6 and D7 are all writable, but will read the chip status. INT0 and INT1 indicate the state of the corresponding interrupt input. D7 and D6 always read 0. See Section 6.3. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 5 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic Table 4. Control register: Write—channel selection; Read—channel status D7 D6 INT1 INT0 D3 B2 B1 B0 Command X X X X X 0 X X no channel selected X X X X X 1 0 0 channel 0 enabled X X X X X 1 0 1 channel 1 enabled X X X X X 1 1 X no channel selected 0 0 0 0 0 0 0 0 no channel selected; power-up default state 6.3 Interrupt handling The PCA9542A provides 2 interrupt inputs, one for each channel and one open-drain interrupt output. When an interrupt is generated by any device, it will be detected by the PCA9542A and the interrupt output will be driven LOW. The channel need not be active for detection of the interrupt. A bit is also set in the control byte. Bits 5:4 of the control byte correspond to channel 1, channel 0 of the PCA9542A, respectively. Therefore, if an interrupt is generated by any device connected to channel 1, the state of the interrupt inputs is loaded into the control register when a read is accomplished. Likewise, an interrupt on any device connected to channel 0 would cause bit 4 of the control register to be set on the read. The master can then address the PCA9542A and read the contents of the control byte to determine which channel contains the device generating the interrupt. The master can then reconfigure the PCA9542A to select this channel, and locate the device generating the interrupt and clear it. It should be noted that more than one device can be providing an interrupt on a channel, so it is up to the master to ensure that all devices on a channel are interrogated for an interrupt. The interrupt inputs may be used as general purpose inputs if the interrupt function is not required. If unused, interrupt input(s) must be connected to VDD through a pull-up resistor. Table 5. D7 Control register read — interrupt D6 0 0 0 0 INT1 X 0 1 INT0 0 1 X D3 B2 B1 B0 X X X X X X X X Command no interrupt on channel 0 interrupt on channel 0 no interrupt on channel 1 interrupt on channel 1 Remark: The two interrupts can be active at the same time. D6 and D7 always read 0. 6.4 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9542A in a reset condition until VDD has reached VPOR. At this point, the reset condition is released and the PCA9542A registers and I2C-bus state machine are initialized to their default states (all zeroes), causing all the channels to be deselected. Thereafter, VDD must be lowered below 0.2 V for at least 5 s in order to reset the device. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 6 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 6.5 Voltage translation The pass gate transistors of the PCA9542A are constructed such that the VDD voltage can be used to limit the maximum voltage that will be passed from one I2C-bus to another. 002aaa964 5.0 Vo(sw) (V) 4.0 (1) (2) 3.0 (3) 2.0 1.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) (1) maximum (2) typical (3) minimum Fig 6. Pass gate voltage versus supply voltage Figure 6 shows the voltage characteristics of the pass gate transistors (note that the graph was generated using the data specified in Section 12 “Dynamic characteristics” of this data sheet). In order for the PCA9542A to act as a voltage translator, the Vo(sw) voltage should be equal to, or lower than the lowest bus voltage. For example, if the main bus was running at 5 V, and the downstream buses were 3.3 V and 2.7 V, then Vo(sw) should be equal to or below 2.7 V to effectively clamp the downstream bus voltages. Looking at Figure 6, we see that Vo(sw)(max) will be at 2.7 V when the PCA9542A supply voltage is 3.5 V or lower so the PCA9542A supply voltage could be set to 3.3 V. Pull-up resistors can then be used to bring the bus voltages to their appropriate levels (see Figure 13). More Information can be found in Application Note AN262, PCA954X family of I2C/SMBus multiplexers and switches. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 7 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 7. Characteristics of the I2C-bus The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 7.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as control signals (see Figure 7). SDA SCL data line stable; data valid Fig 7. change of data allowed mba607 Bit transfer 7.2 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition (P) (see Figure 8). SDA SCL S P START condition STOP condition mba608 Fig 8. Definition of START and STOP conditions 7.3 System configuration A device generating a message is a ‘transmitter’, a device receiving is the ‘receiver’. The device that controls the message is the ‘master’ and the devices which are controlled by the master are the ‘slaves’ (see Figure 9). PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 8 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic SDA SCL MASTER TRANSMITTER/ RECEIVER SLAVE RECEIVER SLAVE TRANSMITTER/ RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER I2C-BUS MULTIPLEXER SLAVE 002aaa966 Fig 9. System configuration 7.4 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also, a master must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse; set-up and hold times must be taken into account. A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 2 S START condition 8 9 clock pulse for acknowledgement 002aaa987 Fig 10. Acknowledgement on the I2C-bus PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 9 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 7.5 Bus transactions slave address SDA S 1 1 1 0 A2 control register A1 A0 START condition 0 A R/W X X X X X B2 acknowledge from slave B1 B0 A P acknowledge from slave STOP condition 002aae299 Fig 11. Write control register slave address SDA S 1 1 1 0 A2 last byte control register A1 A0 START condition 1 A R/W X X INT INT 1 0 X B2 acknowledge from slave B1 B0 NA P no acknowledge from master STOP condition 002aae305 Fig 12. Read control register 8. Application design-in information VDD = 2.7 V to 5.5 V VDD = 3.3 V V = 2.7 V to 5.5 V (1) SDA SDA SD0 SCL SCL SC0 INT INT0 PCA9542A I2C-bus/SMBus master channel 0 V = 2.7 V to 5.5 V (1) A2 A1 SD1 A0 SC1 VSS INT1 channel 1 002aae306 (1) If the device generating the interrupt has an open-drain output structure or can be 3-stated, a pull-up resistor is required. If the device generating the interrupt has a totem pole output structure and cannot be 3-stated, a pull-up resistor is not required. The interrupt inputs should not be left floating. Fig 13. Typical application PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 10 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 9. Limiting values Table 6. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to ground (VSS = 0 V).[1] Symbol Parameter VDD VI Conditions Min Max Unit supply voltage 0.5 +7.0 V input voltage 0.5 +7.0 V II input current - 20 mA IO output current - 25 mA IDD supply current - 100 mA ISS ground supply current - 100 mA Ptot total power dissipation - 400 mW - 125 C Tj(max) maximum junction temperature Tstg storage temperature Tamb ambient temperature [1] [1] operating 60 +150 C 40 +85 C The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 125 C. 10. Thermal characteristics Table 7. PCA9542A Product data sheet Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient SO14 package 127 C/W TSSOP14 package 175 C/W All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 11 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 11. Static characteristics Table 8. Static characteristics at VDD = 2.3 V to 3.6 V VSS = 0 V; Tamb = 40 C to +85 C; unless otherwise specified. See Table 9 for VDD = 4.5 V to 5.5 V.[1] Symbol Parameter Conditions Min Typ Max Unit Supply VDD supply voltage 2.3 - 3.6 V IDD supply current operating mode; VDD = 3.6 V; no load; VI = VDD or VSS; fSCL = 100 kHz - 10 30 A Istb standby current standby mode; VDD = 3.6 V; no load; VI = VDD or VSS; fSCL = 0 kHz - 0.1 1 A VPOR power-on reset voltage no load; VI = VDD or VSS - 1.6 2.1 V [2] Input SCL; input/output SDA VIL LOW-level input voltage 0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 6 V IOL LOW-level output current VOL = 0.4 V 3 7 - mA VOL = 0.6 V 6 10 - mA IL leakage current VI = VDD or VSS 1 - +1 A Ci input capacitance VI = VSS - 9 10 pF 0.5 - +0.3VDD V Select inputs A0, A1, A2, INT0, INT1 VIL LOW-level input voltage VIH HIGH-level input voltage 0.7VDD - 6 V ILI input leakage current VI = VDD or VSS 1 - +1 A Ci input capacitance VI = VSS - 1.6 3 pF ON-state resistance VDD = 3.0 V to 3.6 V; VO = 0.4 V; IO = 15 mA 5 11 30  VDD = 2.3 V to 2.7 V; VO = 0.4 V; IO = 10 mA 7 16 55  Vi(sw) = VDD = 3.3 V; Io(sw) = 100 A - 1.9 - V Vi(sw) = VDD = 3.0 V to 3.6 V; Io(sw) = 100 A 1.6 - 2.8 V Vi(sw) = VDD = 2.5 V; Io(sw) = 100 A - 1.5 - V Vi(sw) = VDD = 2.3 V to 2.7 V; Io(sw) = 100 A 1.1 - 2.0 V Pass gate Ron Vo(sw) switch output voltage IL leakage current VI = VDD or VSS 1 - +1 A Cio input/output capacitance VI = VSS - 3 5 pF IOL LOW-level output current VOL = 0.4 V 3 - - mA IOH HIGH-level output current - - +10 A INT output [1] For operation between published voltage ranges, refer to worst case parameter in both ranges. [2] VDD must be lowered to 0.2 V for at least 5 s in order to reset part. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 12 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic Table 9. Static characteristics at VDD = 4.5 V to 5.5 V VSS = 0 V; Tamb = 40 C to +85 C; unless otherwise specified. See Table 8 for VDD = 2.3 V to 3.6 V.[1] Symbol Parameter Conditions Min Typ Max Unit 4.5 - 5.5 V Supply VDD supply voltage IDD supply current operating mode; VDD = 5.5 V; no load; VI = VDD or VSS; fSCL = 100 kHz - 25 100 A Istb standby current standby mode; VDD = 5.5 V; no load; VI = VDD or VSS; fSCL = 0 kHz - 0.3 1 A VPOR power-on reset voltage no load; VI = VDD or VSS - 1.7 2.1 V [2] Input SCL; input/output SDA VIL LOW-level input voltage 0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 6 V IOL LOW-level output current VOL = 0.4 V 3 - - mA VOL = 0.6 V 6 - - mA IL leakage current VI = VDD or VSS 1 - +1 A Ci input capacitance VI = VSS - 9 10 pF Select inputs A0, A1, A2, INT0, INT1 VIL LOW-level input voltage 0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 6 V ILI input leakage current VI = VDD or VSS 1 - +1 A Ci input capacitance VI = VSS - 2 5 pF Ron ON-state resistance VDD = 4.5 V to 5.5 V; VO = 0.4 V; IO = 15 mA 4 9 24  Vo(sw) switch output voltage Vi(sw) = VDD = 5.0 V; Io(sw) = 100 A - 3.6 - V Vi(sw) = VDD = 4.5 V to 5.5 V; Io(sw) = 100 A 2.6 - 4.5 V Pass gate IL leakage current VI = VDD or VSS 1 - +1 A Cio input/output capacitance VI = VSS - 3 5 pF IOL LOW-level output current VOL = 0.4 V 3 - - mA IOH HIGH-level output current - - +10 A INT output [1] For operation between published voltage ranges, refer to worst case parameter in both ranges. [2] VDD must be lowered to 0.2 V for at least 5 s in order to reset part. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 13 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 12. Dynamic characteristics Table 10. Symbol Dynamic characteristics Parameter Conditions Standard-mode I2C-bus from SDA to SDx, or SCL to SCx Fast-mode I2C-bus Unit Min Max Min Max - 0.3[1] - 0.3[1] ns 0 100 0 400 kHz 4.7 - 1.3 - s 4.0 - 0.6 - s s tPD propagation delay fSCL SCL clock frequency tBUF bus free time between a STOP and START condition tHD;STA hold time (repeated) START condition tLOW LOW period of the SCL clock 4.7 - 1.3 - tHIGH HIGH period of the SCL clock 4.0 - 0.6 - s tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - s tSU;STO set-up time for STOP condition 4.0 - 0.6 - s [2] tHD;DAT data hold time 0[3] 3.45 0[3] 0.9 s tSU;DAT data set-up time 250 - 100 - ns tr rise time of both SDA and SCL signals - 1000 20 + 0.1Cb[4] 300 ns tf fall time of both SDA and SCL signals - 300 20 + 0.1Cb[4] 300 ns Cb capacitive load for each bus line - 400 - 400 pF tSP pulse width of spikes that must be suppressed by the input filter - 50 - 50 ns tVD;DAT data valid time tVD;ACK HIGH-to-LOW [5] - 1 - 1 s LOW-to-HIGH [5] - 0.6 - 0.6 s - 1 - 1 s data valid acknowledge time INT tv(INTnN-INTN) valid time from INTn to INT signal [5] - 4 - 4 s td(INTnN-INTN) delay time from INTn to INT inactive [5] - 2 - 2 s INTn inputs [5] 1 - 1 - s INTn inputs [5] 0.5 - 0.5 - s tw(rej)L tw(rej)H LOW-level rejection time HIGH-level rejection time [1] Pass gate propagation delay is calculated from the 20  typical Ron and the 15 pF load capacitance. [2] After this period, the first clock pulse is generated. [3] A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIH(min) of the SCL signal) in order to bridge the undefined region of the falling edge of SCL. [4] Cb = total capacitance of one bus line in pF. [5] Measurements taken with 1 k pull-up resistor and 50 pF load. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 14 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic î9'' 6'$ î9'' WU W%8) WI W+'67$ W63 W/2: î9'' 6&/ î9'' W+'67$ 3 6 W+''$7 W+,*+ W68'$7 W6867$ 6U W68672 3 DDD Fig 14. Definition of timing on the I2C-bus PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 15 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 13. Package outline 62SODVWLFVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP 627 ' ( $ ; F \ +( Y 0 $ =   4 $ $ $   $ SLQLQGH[ ș /S  /  H GHWDLO; Z 0 ES   PP VFDOH ',0(16,216 LQFKGLPHQVLRQVDUHGHULYHGIURPWKHRULJLQDOPPGLPHQVLRQV  81,7 $ PD[ $ $ $ ES F '   (   H +( / /S 4 Y Z \ =   PP                                                 LQFKHV        ș R R  1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPP LQFK PD[LPXPSHUVLGHDUHQRWLQFOXGHG 5()(5(1&(6 287/,1( 9(56,21 ,(& -('(& 627 ( 06 -(,7$ (8523($1 352-(&7,21 ,668('$7(   Fig 15. Package outline SOT108-1 (SO14) PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 16 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 76623SODVWLFWKLQVKULQNVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP ' 627 ( $ ; F \ +( Y 0 $ =   4 $ SLQLQGH[ $   $ $ ș /S /   H GHWDLO; Z 0 ES   PP VFDOH ',0(16,216 PPDUHWKHRULJLQDOGLPHQVLRQV  81,7 $ PD[ $ $ $ ES F '   (   H +( / /S 4 Y Z \ =   ș PP                            R R 1RWHV 3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 3ODVWLFLQWHUOHDGSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 287/,1( 9(56,21 627 5()(5(1&(6 ,(& -('(& -(,7$ (8523($1 352-(&7,21 ,668('$7(   02 Fig 16. Package outline SOT402-1 (TSSOP14) PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 17 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 14. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 14.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 14.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 14.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 18 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 14.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 17) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 11 and 12 Table 11. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350  350 < 2.5 235 220  2.5 220 220 Table 12. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 17. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 19 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 17. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 20 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 15. Soldering: PCB footprints )RRWSULQWLQIRUPDWLRQIRUUHIORZVROGHULQJRI62SDFNDJH 627 +[ *[ 3  +\ *\  %\ $\ & ' [ ' 3 *HQHULFIRRWSULQWSDWWHUQ 5HIHUWRWKHSDFNDJHRXWOLQHGUDZLQJIRUDFWXDOOD\RXW VROGHUODQG RFFXSLHGDUHD ',0(16,216LQPP 3 3 $\ %\ & ' ' *[         *\ +[ +\    VRWBIU Fig 18. PCB footprint for SOT108-1 (SO14); reflow soldering PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 21 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic )RRWSULQWLQIRUPDWLRQIRUUHIORZVROGHULQJRI76623SDFNDJH 627 +[ *[ 3   +\ %\ *\ $\ & ' [ ' 3 *HQHULFIRRWSULQWSDWWHUQ 5HIHUWRWKHSDFNDJHRXWOLQHGUDZLQJIRUDFWXDOOD\RXW VROGHUODQG RFFXSLHGDUHD ',0(16,216LQPP 3 3 $\ %\ & ' ' *[ *\ +[ +\            VRWBIU Fig 19. PCB footprint for SOT402-1 (TSSOP14); reflow soldering PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 22 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 16. Abbreviations Table 13. PCA9542A Product data sheet Abbreviations Acronym Description CDM Charged-Device Model ESD ElectroStatic Discharge HBM Human Body Model I/O Input/Output I2C-bus Inter-Integrated Circuit bus LSB Least Significant Bit POR Power-On Reset SMBus System Management Bus All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 23 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 17. Revision history Table 14. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9542A v.5.1 20150715 Product data sheet - PCA9542A v.5 Modifications: PCA9542A v.5 Modifications: • Table 14 “Revision history”, corrected phrase “for at least 5 ms” to “for at least 5 s” for Table 8 and Table 9 modifications 20140407 • • • Product data sheet - PCA9542A v.4 Section 2 “Features and benefits”, 16th bullet item: deleted phrase “200 V MM per JESD22-A115” Table 1 “Ordering information”: added column “Topside marking” (moved from Table 2) Table 2 “Ordering options”: – deleted column “Topside mark” (moved to Table 1) – added columns “Orderable part number”, “Package”, “Packing method”, and “Minimum order quantity” • • • • • • • Figure 5 “Control register” updated: added notation ‘writable, but always read 0’ Section 6.2.1 “Control register definition”: added second paragraph Section 6.3 “Interrupt handling”, “Remark” paragraph (following Table 5): added second sentence Section 6.4 “Power-on reset”: first paragraph, third sentence: corrected from “VDD must be lowered below 0.2 V to reset the device” to “VDD must be lowered below 0.2 V for at least 5 s in order to reset the device” Table 6 “Limiting values”: added limiting values for “Tj(max)” Added Section 10 “Thermal characteristics” Table 8 “Static characteristics at VDD = 2.3 V to 3.6 V”, – Table note [2]: inserted phrase “for at least 5 s” – sub-section “Select inputs A0, A1, A2, INT0, INT1”: Max value for VIH corrected from “VDD + 0.5 V” to “6 V” • Table 9 “Static characteristics at VDD = 4.5 V to 5.5 V”, – Table note [2]: inserted phrase “for at least 5 s” – sub-section “Select inputs A0, A1, A2, INT0, INT1”: Max value for VIH corrected from “VDD + 0.5 V” to “6 V” • Added Section 15 “Soldering: PCB footprints” PCA9542A v.4 20090615 Product data sheet - PCA9542A v.3 PCA9542A v.3 20081124 Product data sheet - PCA9542A v.2 PCA9542A v.2 (9397 750 13955) 20040929 Product data sheet - PCA9542A v.1 PCA9542A v.1 (9397 750 13307) 20040727 Objective data sheet - - PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 24 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 18.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCA9542A Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 25 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP Semiconductors N.V. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9542A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5.1 — 15 July 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 26 of 27 PCA9542A NXP Semiconductors 2-channel I2C-bus multiplexer and interrupt logic 20. Contents 1 2 3 3.1 4 5 5.1 5.2 6 6.1 6.2 6.2.1 6.3 6.4 6.5 7 7.1 7.2 7.3 7.4 7.5 8 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 17 18 18.1 18.2 18.3 18.4 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Device addressing . . . . . . . . . . . . . . . . . . . . . . 5 Control register . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control register definition . . . . . . . . . . . . . . . . . 5 Interrupt handling . . . . . . . . . . . . . . . . . . . . . . . 6 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 6 Voltage translation . . . . . . . . . . . . . . . . . . . . . . 7 Characteristics of the I2C-bus . . . . . . . . . . . . . 8 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 START and STOP conditions . . . . . . . . . . . . . . 8 System configuration . . . . . . . . . . . . . . . . . . . . 8 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . 10 Application design-in information . . . . . . . . . 10 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 11 Thermal characteristics . . . . . . . . . . . . . . . . . 11 Static characteristics. . . . . . . . . . . . . . . . . . . . 12 Dynamic characteristics . . . . . . . . . . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Soldering of SMD packages . . . . . . . . . . . . . . 18 Introduction to soldering . . . . . . . . . . . . . . . . . 18 Wave and reflow soldering . . . . . . . . . . . . . . . 18 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 18 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 19 Soldering: PCB footprints. . . . . . . . . . . . . . . . 21 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 24 Legal information. . . . . . . . . . . . . . . . . . . . . . . 25 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 25 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Contact information. . . . . . . . . . . . . . . . . . . . . 26 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2015. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 15 July 2015 Document identifier: PCA9542A
PCA9542AD,118 价格&库存

很抱歉,暂时无法提供与“PCA9542AD,118”相匹配的价格&库存,您可以联系我们找货

免费人工找货