PCA9698DGG,518

PCA9698 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Rev. 3 — 3 August 2010 Product data sheet 1. General description The PCA9698 provides 40-bit parallel input/output (I/O) port expansion for I2C-bus applications organized in 5 banks of 8 I/Os. At 5 V supply voltage, the outputs are capable of sourcing 10 mA and sinking 25 mA with a total package load of 1 A to allow direct driving of 40 LEDs. Any of the 40 I/O ports can be configured as an input or output. The PCA9698 is the first GPIO device in a new Fast-mode Plus (Fm+) family. Fm+ devices offer higher frequency (up to 1 MHz) and longer, more densely populated bus operation (up to 4000 pF). The device is fully configurable: output ports can be programmed to be totem-pole or open-drain and logic states can change at either the Acknowledge (bank change) or the Stop Command (global change), each input port can be masked to prevent it from generating interrupts when its state changes, I/O data logic state can be inverted when read by the system master. An open-drain interrupt output pin (INT) allows monitoring of the input pins and is asserted each time a change occurs in one or several input ports (unless masked). The Output Enable pin (OE) 3-states any I/O selected as output and can be used as an input signal to blink or dim LEDs (PWM with frequency > 80 Hz and change duty cycle). A ‘GPIO All Call’ command allows to program multiple Advanced GPIOs at the same time even if they have different I2C-bus addresses. This allows optimal code programming when more than one device needs to be programmed with the same instruction or if all outputs need to be turned on or off at the same time (for example, LED test). The Device ID, hard coded in the PCA9698, allows the system master to read manufacturer, part type and revision information. The SMBus Alert feature allows the SMBALERT pins of multiple devices with this feature to be connected together to form a wired-AND signal and to be used in conjunction with the SMBus Alert Response Address. The internal Power-On Reset (POR) or hardware reset pin (RESET) initializes the 40 I/Os as inputs. Three address select pins configure one of 64 slave addresses. The PCA9698 is available in 56-pin TSSOP and HVQFN packages and is specified over the −40 °C to +85 °C industrial temperature range. 2. Features and benefits „ 1 MHz Fast-mode Plus I2C-bus serial interface „ Compliant with I2C-bus Fast-mode (400 kHz) and Standard-mode (100 kHz) PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT „ 2.3 V to 5.5 V operation with 5.5 V tolerant I/Os „ 40 configurable I/O pins that default to inputs at power-up „ Outputs: ‹ Programmable totem-pole (10 mA source, 25 mA sink) or open-drain (25 mA sink) with controlled edge rate output structure. Default to totem-pole on power-up. ‹ Active LOW Output Enable (OE) input pin 3-states all outputs. Polarity can be programmed to active HIGH through the I2C-bus. Defaults to OE on power-up. ‹ Output state change programmable on the Acknowledge or the STOP Command to update outputs byte-by-byte or all at the same time respectively. Defaults to Acknowledge on power-up. „ Inputs: ‹ Open-drain active LOW Interrupt (INT) output pin allows monitoring of logic level change of pins programmed as inputs ‹ Programmable Interrupt Mask Control for input pins that do not require an interrupt when their states change ‹ Polarity Inverter register allows inversion of the polarity of the I/O pins when read „ Active LOW SMBus Alert (SMBALERT) output pin allows to initiate SMBus ‘Alert Response Address’ sequence. Own slave address sent when sequence initiated. „ Active LOW Reset (RESET) input pin resets device to power-up default state „ GPIO All Call address allows programming of more than one device at the same time with the same parameters „ 64 programmable slave addresses using 3 address pins „ Readable Device ID (manufacturer, device type and revision) „ Designed for live insertion in PICMG applications ‹ Minimize line disturbance (IOFF and power-up 3-state) ‹ Signal transient rejection (50 ns noise filter and robust I2C-bus state machine) „ Low standby current „ −40 °C to +85 °C operation „ ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 „ Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA „ Packages offered: TSSOP56, and HVQFN56 3. Applications „ „ „ „ „ „ „ „ PCA9698 Product data sheet Servers RAID systems Industrial control Medical equipment PLCs Cell phones Gaming machines Instrumentation and test measurement All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 2 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 4. Ordering information Table 1. Ordering information Tamb = −40 °C to +85 °C Type number Topside mark Package Name Description Version PCA9698DGG PCA9698DGG TSSOP56 plastic thin shrink small outline package; 56 leads; body width 6.1 mm SOT364-1 PCA9698BS PCA9698BS HVQFN56 plastic thermal enhanced very thin quad flat package; no leads; 56 terminals; body 8 × 8 × 0.85 mm SOT684-1 5. Block diagram OE PCA9698 AD0 AD1 AD2 8-bit INPUT/ OUTPUT PORTS read pulse 0 BANK 0 ADDRESS DECODER IO0_0 IO0_1 IO0_2 IO0_3 IO0_4 IO0_5 IO0_6 IO0_7 write pulse 0 BANK 1 SCL SDA LOW PASS INPUT FILTERS I2C-BUS/SMBUS CONTROL BANK 2 BANK 3 8-bit INPUT/ OUTPUT PORTS read pulse 4 BANK 4 VDD VSS POWER-ON RESET IO4_0 IO4_1 IO4_2 IO4_3 IO4_4 IO4_5 IO4_6 IO4_7 write pulse 4 RESET INTERRUPT MANAGEMENT INT/SMBALERT LP FILTER 002aab935 Remark: All I/Os are set to inputs at power-up and RESET. Fig 1. PCA9698 Product data sheet Block diagram of PCA9698 All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 3 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT configuration port register data (Cx[y]) output port register data (Ox[y]) OE OEPOL I/O configuration register data from shift register D Q VDD OUTx FF write configuration pulse CK Q IOx_y output port register data from shift register D D Q Q FF FF Mx[y] OCH CK write pulse CK STOP pulse INTERRUPT MANAGEMENT INT input port register D Q FF read pulse input port register data (Ix[y]) CK polarity inversion register data from shift register D Q FF write polarity pulse polarity inversion register data (Px[y]) CK 002aab936 On power-up or RESET, all registers return to default values. Fig 2. Simplified schematic of the I/Os (IO0_0 to IO4_7) PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 4 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 6. Pinning information 6.1 Pinning SDA 1 56 RESET SCL 2 55 INT/SMBALERT IO0_0 3 54 IO4_7 IO0_1 4 53 IO4_6 IO0_2 5 52 IO4_5 VSS 6 51 VSS IO0_3 7 50 IO4_4 IO0_4 8 49 IO4_3 IO0_5 9 48 IO4_2 IO0_6 10 47 IO4_1 VSS 11 46 VDD IO0_7 12 45 IO4_0 IO1_0 13 44 IO3_7 IO1_1 14 IO1_2 15 43 IO3_6 PCA9698DGG 42 IO3_5 IO1_3 16 41 IO3_4 IO1_4 17 40 IO3_3 VDD 18 39 VSS IO1_5 19 38 IO3_2 IO1_6 20 37 IO3_1 IO1_7 21 36 IO3_0 IO2_0 22 35 IO2_7 VSS 23 34 VSS IO2_1 24 33 IO2_6 IO2_2 25 32 IO2_5 IO2_3 26 31 IO2_4 AD0 27 30 OE AD1 28 29 AD2 002aab932 Fig 3. PCA9698 Product data sheet Pin configuration for TSSOP56 All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 5 of 48 PCA9698 NXP Semiconductors 43 IO4_4 44 VSS 45 IO4_5 46 IO4_6 47 IO4_7 48 INT/SMBALERT 49 RESET 50 SDA 51 SCL 52 IO0_0 53 IO0_1 54 IO0_2 terminal 1 index area 55 VSS 56 IO0_3 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT IO0_4 1 42 IO4_3 IO0_5 2 41 IO4_2 IO0_6 3 40 IO4_1 VSS 4 39 VDD IO0_7 5 38 IO4_0 IO1_0 6 37 IO3_7 IO1_1 7 IO1_2 8 IO1_3 9 34 IO3_4 IO1_4 10 33 IO3_3 36 IO3_6 PCA9698BS 35 IO3_5 VDD 11 32 VSS IO2_7 28 VSS 27 IO2_6 26 IO2_5 25 IO2_4 24 OE 23 AD2 22 AD1 21 AD0 20 IO2_3 19 IO2_2 18 29 IO3_0 IO2_1 17 30 IO3_1 IO1_7 14 VSS 16 31 IO3_2 IO1_6 13 IO2_0 15 IO1_5 12 002aab934 Transparent top view Fig 4. Pin configuration for HVQFN56 6.2 Pin description Table 2. PCA9698 Product data sheet Pin description Symbol Pin Type Description TSSOP56 HVQFN56 SDA 1 50 input/output serial data line SCL 2 51 input serial clock line IO0_0 to IO0_7 3, 4, 5, 7, 8, 9, 10, 12 52, 53, 54, 56, 1, 2, 3, 5 input/output input/output bank 0 IO1_0 to IO1_7 13, 14, 15, 16, 17, 19, 20, 21 6, 7, 8, 9, 10, 12, 13, 14 input/output input/output bank 1 IO2_0 to IO2_7 22, 24, 25, 26, 31, 32, 33, 35 15, 17, 18, 19, 24, 25, 26, 28 input/output input/output bank 2 IO3_0 to IO3_7 36, 37, 38, 40, 41, 42, 43, 44 29, 30, 31, 33, 34, 35, 36, 37 input/output input/output bank 3 IO4_0 to IO4_7 45, 47, 48, 49, 50, 52, 53, 54 38, 40, 41, 42, 43, 45, 46, 47 input/output input/output bank 4 VSS 6, 11, 23, 34, 39, 51 4, 16, 27, 32, 44, 55[1] power supply supply ground VDD 18, 46 11, 39 power supply supply voltage AD0 27 20 input address input 0 AD1 28 21 input address input 1 All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 6 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Table 2. Pin description …continued Symbol Pin Type Description 22 input address input 2 30 23 input active LOW output enable INT/SMBALERT 55 48 output active LOW interrupt output/ active LOW SMBus alert output RESET 56 49 input active LOW reset input TSSOP56 HVQFN56 AD2 29 OE [1] HVQFN56 package die supply ground is connected to both VSS pins and exposed center pad. VSS pins must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the printed-circuit board in the thermal pad region. 7. Functional description Refer to Figure 1 “Block diagram of PCA9698”. 7.1 Device address Following a START condition the bus master must send the address of the slave it is accessing and the operation it wants to perform (read or write). The address of the PCA9698 is shown in Figure 5. Slave address pins AD2, AD1 and AD0 choose 1 of 64 slave addresses. To conserve power, no internal pull-up resistors are incorporated on AD2, AD1 and AD0. Address values depending on AD2, AD1 and AD0 can be found in Table 12 “PCA9698 address map”. slave address A6 A5 A4 A3 A2 A1 programmable Fig 5. A0 R/W 002aab937 PCA9698 device address The last bit of the first byte defines the operation to be performed. When set to logic 1 a read is selected while a logic 0 selects a write operation. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 7 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.2 Alert response, GPIO All Call and Device ID addresses Three other different addresses can be sent to the PCA9698. • Alert Response address: allows to perform an ‘SMBus Alert’ operation as defined in the SMBus specification. This address is always used to perform a Read operation. See Section 7.11 “SMBus Alert output (SMBALERT)” for more information. • GPIO All Call address: allows to program several Advanced GPIO devices at the same time. This address is always used to perform a Write operation. See Section 7.6 “GPIO All Call” for more information. • Device ID address: allows to read ID information from the device (manufacturer, part identification, revision). See Section 7.5 “Device ID - PCA9698 ID field” for more information. R/W 0 0 0 1 1 0 0 1 R/W 1 1 0 1 1 1 002aab938 Fig 6. Alert Response address 0 0 1 1 1 1 1 0 002aab939 Fig 7. 0 R/W 002aab940 GPIO All Call address Fig 8. Device ID address 7.3 Command register Following the successful acknowledgement of the slave address + R/W bit, the bus master will send a byte to the PCA9698, which will be stored in the Command register. AI − D5 D4 D3 D2 D1 D0 1 0 0 0 0 0 0 0 default at power-up or after RESET register number Auto-Increment Fig 9. 002aab941 Command register The lowest 6 bits are used as a pointer to determine which register will be accessed. Registers are divided into 2 categories: 5-bank register category, and 1-bank register category. Only a command register code with the 7 least significant bits equal to the 28 allowable values as defined in Table 3 “Register summary” will be acknowledged. Reserved or undefined command codes will not be acknowledged. At power-up, this register defaults to 80h, with the AI bit set to ‘1’, and the lowest 7 bits set to ‘0'. During a write operation, the PCA9698 will acknowledge a byte sent to the OP, PI, IOC, MSK, OUTCONF, ALLBNK, and MODE registers, but will not acknowledge a byte sent to the IPx registers since these are read-only registers. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 8 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.3.1 5-bank register category • • • • • IP – Input registers OP – Output registers PI – Polarity Inversion registers IOC – I/O Configuration registers MSK – Mask interrupt registers If the Auto-Increment flag is set (AI = 1), the 3 least significant bits are automatically incremented after a read or write. This allows the user to program and/or read the 5 register banks sequentially. If more than 5 bytes of data are written and AI = 1, previous data in the selected registers will be overwritten or reread. Reserved registers are skipped and not accessed (refer to Table 3). If the Auto-Increment flag is cleared (AI = 0), the 3 least significant bits are not incremented after data is read or written, only one register will be repeatedly read or written. 7.3.2 1-bank register category • OUTCONF – Output Structure Configuration register • ALLBNK – All Bank Control register • MODE – Mode Selection register If more than 1 byte of data is written or read, previous data in the same register is overwritten independently of the value of AI. 7.4 Register definitions Table 3. Reg # Register summary D5 D4 D3 D2 D1 D0 Name Type Function Input Port registers 00h 0 0 0 0 0 0 IP0 read only Input Port register bank 0 01h 0 0 0 0 0 1 IP1 read only Input Port register bank 1 02h 0 0 0 0 1 0 IP2 read only Input Port register bank 2 03h 0 0 0 0 1 1 IP3 read only Input Port register bank 3 04h 0 0 0 1 0 0 IP4 read only Input Port register bank 4 05h 0 0 0 1 0 1 - - reserved for future use 06h 0 0 0 1 1 0 - - reserved for future use 07h 0 0 0 1 1 1 - - reserved for future use PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 9 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Table 3. Reg # Register summary …continued D5 D4 D3 D2 D1 D0 Name Type Function Output Port registers 08h 0 0 1 0 0 0 OP0 read/write Output Port register bank 0 09h 0 0 1 0 0 1 OP1 read/write Output Port register bank 1 0Ah 0 0 1 0 1 0 OP2 read/write Output Port register bank 2 0Bh 0 0 1 0 1 1 OP3 read/write Output Port register bank 3 0Ch 0 0 1 1 0 0 OP4 read/write Output Port register bank 4 0Dh 0 0 1 1 0 1 - - reserved for future use 0Eh 0 0 1 1 1 0 - - reserved for future use 0Fh 0 0 1 1 1 1 - - reserved for future use 0 0 0 PI0 read/write Polarity Inversion register bank 0 Polarity Inversion registers 10h 0 1 0 11h 0 1 0 0 0 1 PI1 read/write Polarity Inversion register bank 1 12h 0 1 0 0 1 0 PI2 read/write Polarity Inversion register bank 2 13h 0 1 0 0 1 1 PI3 read/write Polarity Inversion register bank 3 14h 0 1 0 1 0 0 PI4 read/write Polarity Inversion register bank 4 15h 0 1 0 1 0 1 - - reserved for future use 16h 0 1 0 1 1 0 - - reserved for future use 17h 0 1 0 1 1 1 - - reserved for future use I/O Configuration registers 18h 0 1 1 0 0 0 IOC0 read/write I/O Configuration register bank 0 19h 0 1 1 0 0 1 IOC1 read/write I/O Configuration register bank 1 1Ah 0 1 1 0 1 0 IOC2 read/write I/O Configuration register bank 2 1Bh 0 1 1 0 1 1 IOC3 read/write I/O Configuration register bank 3 1Ch 0 1 1 1 0 0 IOC4 read/write I/O Configuration register bank 4 1Dh 0 1 1 1 0 1 - - reserved for future use 1Eh 0 1 1 1 1 0 - - reserved for future use 1Fh 0 1 1 1 1 1 - - reserved for future use Mask Interrupt registers 20h 1 0 0 0 0 0 MSK0 read/write Mask interrupt register bank 0 21h 1 0 0 0 0 1 MSK1 read/write Mask interrupt register bank 1 22h 1 0 0 0 1 0 MSK2 read/write Mask interrupt register bank 2 23h 1 0 0 0 1 1 MSK3 read/write Mask interrupt register bank 3 24h 1 0 0 1 0 0 MSK4 read/write Mask interrupt register bank 4 25h 1 0 0 1 0 1 - - reserved for future use 26h 1 0 0 1 1 0 - - reserved for future use 27h 1 0 0 1 1 1 - - reserved for future use Miscellaneous 28h 1 0 1 0 0 0 OUTCONF read/write output structure configuration 29h 1 0 1 0 0 1 ALLBNK read/write control all banks 2Ah 1 0 1 0 1 0 MODE read/write PCA9698 mode selection PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 10 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.4.1 IP0 to IP4 - Input Port registers These registers are read-only. They reflect the incoming logic levels of the port pins regardless of whether the pin is defined as an input or an output by the I/O Configuration register. If the corresponding Px[y] bit in the PI registers is set to 0, or the inverted incoming logic levels if the corresponding Px[y] bit in the PI register is set to 1. Writes to these registers have no effect. Table 4. IP0 to IP4 - Input Port registers (address 00h to 04h) bit description Legend: * default value ‘X’ determined by the externally applied logic level. Address Register Bit Symbol Access Value Description 00h IP0 7 to 0 I0[7:0] R XXXX XXXX* Input Port register bank 0 01h IP1 7 to 0 I1[7:0] R XXXX XXXX* Input Port register bank 1 02h IP2 7 to 0 I2[7:0] R XXXX XXXX* Input Port register bank 2 03h IP3 7 to 0 I3[7:0] R XXXX XXXX* Input Port register bank 3 04h IP4 7 to 0 I4[7:0] R XXXX XXXX* Input Port register bank 4 The Polarity Inversion register can invert the logic states of the port pins. The polarity of the corresponding bit is inverted when Px[y] bit in the PI register is set to 1. The polarity of the corresponding bit is not inverted when Px[y] bits in the PI register is set to 0. 7.4.2 OP0 to OP4 - Output Port registers These registers reflect the outgoing logic levels of the pins defined as outputs by the I/O Configuration register. Bit values in these registers have no effect on pins defined as inputs. In turn, reads from these registers reflect the values that are in the flip-flops controlling the output selection, not the actual pin values. Ox[y] = 0: IOx_y = 0 if IOx_y defined as output (Cx[y] in IOC register = 0). Ox[y] = 1: IOx_y = 1 if IOx_y defined as output (Cx[y] in IOC register = 0). Where ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Table 5. OP0 to OP4 - Output Port registers (address 08h to 0Ch) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 08h OP0 7 to 0 O0[7:0] R/W 0000 0000* Output Port register bank 0 09h OP1 7 to 0 O1[7:0] R/W 0000 0000* Output Port register bank 1 0Ah OP2 7 to 0 O2[7:0] R/W 0000 0000* Output Port register bank 2 0Bh OP3 7 to 0 O3[7:0] R/W 0000 0000* Output Port register bank 3 0Ch OP4 7 to 0 O4[7:0] R/W 0000 0000* Output Port register bank 4 PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 11 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.4.3 PI0 to PI4 - Polarity Inversion registers These registers allow inversion of the polarity of the corresponding Input Port register. Px[y] = 0: The corresponding Input Port register data polarity is retained. Px[y] = 1: The corresponding Input Port register data polarity is inverted. Where ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Table 6. PI0 to PI4 - Polarity Inversion registers (address 10h to 14h) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 10h PI0 7 to 0 P0[7:0] R/W 0000 0000* Polarity Inversion register bank 0 11h PI1 7 to 0 P1[7:0] R/W 0000 0000* Polarity Inversion register bank 1 12h PI2 7 to 0 P2[7:0] R/W 0000 0000* Polarity Inversion register bank 2 13h PI3 7 to 0 P3[7:0] R/W 0000 0000* Polarity Inversion register bank 3 14h PI4 7 to 0 P4[7:0] R/W 0000 0000* Polarity Inversion register bank 4 7.4.4 IOC0 to IOC4 - I/O Configuration registers These registers configure the direction of the I/O pins. Cx[y] = 0: The corresponding port pin is an output. Cx[y] = 1: The corresponding port pin is an input. Where ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Table 7. IOC0 to IOC4 - I/O Configuration registers (address 18h to 1Ch) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 18h IOC0 7 to 0 C0[7:0] R/W 1111 1111* I/O Configuration register bank 0 19h IOC1 7 to 0 C1[7:0] R/W 1111 1111* I/O Configuration register bank 1 1Ah IOC2 7 to 0 C2[7:0] R/W 1111 1111* I/O Configuration register bank 2 1Bh IOC3 7 to 0 C3[7:0] R/W 1111 1111* I/O Configuration register bank 3 1Ch IOC4 7 to 0 C4[7:0] R/W 1111 1111* I/O Configuration register bank 4 PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 12 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.4.5 MSK0 to MSK4 - Mask interrupt registers These registers mask the interrupt due to a change in the I/O pins configured as inputs. ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Mx[y] = 0: A level change at the I/O will generate an interrupt if IOx_y defined as input (Cx[y] in IOC register = 1). Mx[y] = 1: A level change in the input port will not generate an interrupt if IOx_y defined as input (Cx[y] in IOC register = 1). Table 8. MSK0 to MSK4 - Mask interrupt registers (address 20h to 24h) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 20h MSK0 7 to 0 M0[7:0] R/W 1111 1111* Mask Interrupt register bank 0 21h MSK1 7 to 0 M1[7:0] R/W 1111 1111* Mask Interrupt register bank 1 22h MSK2 7 to 0 M2[7:0] R/W 1111 1111* Mask Interrupt register bank 2 23h MSK3 7 to 0 M3[7:0] R/W 1111 1111* Mask Interrupt register bank 3 24h MSK4 7 to 0 M4[7:0] R/W 1111 1111* Mask Interrupt register bank 4 7.4.6 OUTCONF - output structure configuration register Table 9. Bit OUTCONF - output structure configuration register (address 28h) description 7 6 5 4 3 2 1 0 Symbol OUT4 OUT3 OUT2 OUT1 OUT067 OUT045 OUT023 OUT001 Default 1 1 1 1 1 1 1 1 This register controls the configuration of the output ports as open-drain or totem-pole. The 4 least significant bits control the output architecture for bank 0, 2 bits at a time. OUT001 controls the output structure for IO0_0 and IO0_1 OUT023 controls the output structure for IO0_2 and IO0_3 OUT045 controls the output structure for IO0_4 and IO0_5 OUT067 controls the output structure for IO0_6 and IO0_7 The 4 most significant bits control the output architectures for bank 1 to bank 4, each bit controlling one bank. OUT1 controls the output structure for bank 1 (IO1_0 to IO1_7) OUT2 controls the output structure for bank 2 (IO2_0 to IO2_7) OUT3 controls the output structure for bank 3 (IO3_0 to IO3_7) OUT4 controls the output structure for bank 4 (IO4_0 to IO4_7) OUTx = 0: The I/Os are configured with an open-drain structure. OUTx = 1: The I/Os are configured with a totem-pole structure. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 13 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.4.7 ALLBNK - All Bank control register Table 10. Bit ALLBNK - All Bank control register (address 29h) description 7 6 5 4 3 2 1 0 Symbol BSEL X X B4 B3 B2 B1 B0 Default 1 0 0 0 0 0 0 0 This register allows all the I/Os configured as outputs to be programmed with the same logic value. This programming is applied to all the banks or a selection of banks. When this register is programmed, values in the Output Port registers are not changed and do not reflect the states of I/Os configured as outputs anymore. • B0 to B4 controls the logic level to be applied to Bank 0 to Bank 4, respectively. – Bx = 0: All the I/Os configured as outputs in the corresponding Bank x are programmed with 0s. – Bx = 1: All the I/Os configured as outputs in the corresponding Bank x are programmed with 1s. • Bit 5 and bit 6 are not used and can be programmed to either ‘1’ or ‘0’. • BSEL is a filter bit that allows programming of some banks only, and not the others. – BSEL = 0: When Bx = 0, all the I/Os configured as output in the corresponding Bank x are programmed with 0s. When Bx = 1, all the I/Os configured as output in the corresponding Bank x are programmed with their actual value from the corresponding output register. – BSEL = 1: When Bx = 0, all the I/Os configured as output in the corresponding Bank x are programmed with their actual value from the corresponding output register. When Bx = 1, all the I/Os configured as output in the corresponding Bank x are programmed with 1s. 7.4.7.1 Examples • If ALLBNK = 0XX0 0000: All I/Os configured as outputs in Bank 0 to Bank 4 will be programmed with 0s, overwriting values programmed in the five Output Port registers. • If ALLBNK = 1XX1 1111: All I/Os configured as outputs in Bank 0 to Bank 4 will be programmed with 1s, overwriting values programmed in the five Output Port registers. • If ALLBNK = 0XX0 0110: All I/Os configured as outputs in Banks 0, 3, and 4 only will be programmed with 0s, overwriting values programmed in the Output Port registers 0, 3, and 4, while I/Os configured as outputs in Bank 1 and Bank 2 are programmed with values in Output Port registers 1 and 2. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 14 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT • If ALLBNK = 1XX0 1100: All I/Os configured as outputs in Bank 2 and 3 will be programmed with 1s, overwriting values programmed in the Output Port registers 2 and 3, while I/Os configured as outputs in Bank 0, 1, and 4 are programmed with values in Output Port registers 0, 1, and 4. 7.4.8 MODE - PCA9698 mode selection register Table 11. MODE - mode selection register (address 2Ah) description Bit 7 6 5 4 3 2 1 0 Symbol X X X SMBA IOAC X OCH OEPOL Default 0 0 0 0 0 0 1 0 This register allows programming of the PCA9698 modes. • OEPOL bit controls the polarity of OE pin. – OEPOL = 0: OE pin is active LOW. – OEPOL = 1: OE pin is active HIGH (equivalent to OE pin). • OCH bit selects the I2C-bus event where the state of the I/Os configured as outputs change. – OCH = 0: outputs change on STOP command. – OCH = 1: outputs change on ACK. • IOAC bit controls the ability of the device to respond to a ‘GPIO All Call’ command (see Section 7.6 “GPIO All Call” for more information), allowing programming of more than one device at the same time. – IOAC = 0: The device cannot respond to a ‘GPIO All Call’ command. – IOAC = 1: The device can respond to a ‘GPIO All Call’ command. Remark: The ‘GPIO ALL CALL’ command defined for the PCA9698 is different from the I2C-bus protocol ‘General Call’ command. • SMBA bit controls the capability of the PCA9698 to respond to a SMBAlert command. – SMBA = 0: PCA9698 does not respond to an Alert Response Address. – SMBA = 1: PCA9698 responds to an Alert Response Address. Bits 5, 6 and 7 are reserved and must be programmed with 0s. • Unused bits (bits 2, 5, 6 and 7) must be programmed with 0s for proper device operation. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 15 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.5 Device ID - PCA9698 ID field The Device ID field is a 3 byte read-only (24 bits) word giving the following information: • 12 bits with the manufacturer name, unique per manufacturer (e.g., NXP) • 9 bits with the part identification, assigned by manufacturer (e.g., PCA9698) • 3 bits with the die revision, assigned by manufacturer (e.g., RevX) The Device ID is read-only, hard-wired in the device and can be accessed as follows: 1. START command 2. The master sends the Reserved Device ID I2C-bus address followed by the R/W bit set to ‘0’ (write): ‘1111 1000’. 3. The master sends the I2C-bus slave address of the slave device it needs to identify. The LSB is a ‘Don’t care’ value. Only one device must acknowledge this byte (the one that has the I2C-bus slave address). 4. The master sends a Re-START command. Remark: A STOP command followed by a START command will reset the slave state machine and the Device ID Read cannot be performed. Also, a STOP command or a Re-START command followed by an access to another slave device will reset the slave state machine and the Device ID Read cannot be performed. 5. The master sends the Reserved Device ID I2C-bus address followed by the R/W bit set to ‘1’ (read): ‘1111 1001’. 6. The Device ID Read can be done, starting with the 12 manufacturer bits (first byte + 4 MSBs of the second byte), followed by the 9 part identification bits (4 LSBs of the second byte + 5 MSBs of the third byte), and then the 3 die revision bits (3 LSBs of the third byte). 7. The master ends the reading sequence by NACKing the last byte, thus resetting the slave device state machine and allowing the master to send the STOP command. Remark: The reading of the Device ID can be stopped anytime by sending a NACK command. If the master continues to ACK the bytes after the third byte, the PCA9698 rolls back to the first byte and keeps sending the Device ID sequence until a NACK has been detected. For the PCA9698, the Device ID is as shown in Figure 10. manufacturer 0 part identification 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 revision 0 002aab942 Fig 10. PCA9698 ID field PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 16 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.6 GPIO All Call A ‘GPIO All Call’ command allows the programming of multiple advanced GPIOs with different I2C-bus addresses at the same time. This allows to optimize code programming when the master needs to send the same instruction to several devices. To respond to such a command and sequence, the PCA9698 needs to have its IOAC bit (register 2Ah, bit 3) set to 1. Devices that have this bit set to 0 do not participate in any ‘GPIO All Call’ sequence. The ‘GPIO All Call’ command can be performed only for a write operation and cannot be used in conjunction with a read operation. • Master initiates a command sequence with the START command, the ‘GPIO All Call’ command associated with a Write command: Start − 1101 110 + Write • All the devices that are programmed to respond to this command will acknowledge • The master then sends the data and all the devices that are programmed to respond acknowledge the byte(s) • The master ends the sequence by sending a STOP or Repeated START command. If the master initiates a ‘GPIO All Call’ sequence with a Read command, none of the slave devices acknowledge. 7.7 Output state change on ACK or STOP State change of the I/Os programmed as outputs can be done either: • during the ACK phase every time an Output Port register is modified. The output state is then updated one-by-one (at a bank level): OCH bit = 1 (register 2Ah, bit 1) • at a STOP command allowing all the outputs to change at the exact same moment: OCH bit = 0 (register 2Ah, bit 1). Change of the outputs at the STOP command allows synchronizing of all the programmed banks in a single device, and also allows synchronizing outputs of more than one PCA9698. Example 1: Only one PCA9698 is used on the I2C-bus and all the outputs need to change at the same time. • OCH bit (Mode Selection Register, bit 1) must be equal to ‘0’. • The master accesses the device and programs the Output Port register(s) that has (have) to be changed (up to 5 ports). • When done, the master must generate a STOP command. • At the STOP command, the PCA9698 will update the Output Port register(s) that has (have) been programmed and change the output states all at the same time. Example 2: More than one PCA9698 is used on the I2C-bus and all the outputs need to change at the same time. • OCH bit (Mode Selection Register, bit 1) must be equal to ‘0’ in all the devices. • The master device must access the devices one-by-one. • Access to each device must be separated by a Re-START command. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 17 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT • When all the devices have been accessed, the master must generate a STOP command. • At the STOP command, all the PCA9698s that have been accessed will update their Output Port registers that have been programmed and change the output states all at the same time. Remark: After programming a PCA9698, its state machine will be in a ‘wait-for-STOP-condition’ until a STOP condition is received to update the Output Port registers. Since this state machine will be in a ‘wait-state’, the part will not respond to its own address until this state machine gets out to the idle condition, which means that the device can be programmed only once and is not addressable again until a STOP condition has been received. Remark: The PCA9698 has one level of buffers to store 5 bytes of data, and the actual Output Port registers will get updated on the STOP condition. If the master sends more than 5 bytes of data (with AI = 1), the data in the buffer will get overwritten. 7.8 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9698 in a reset condition until VDD has reached VPOR. At that point, the reset condition is released and the PCA9698 registers and I2C-bus/SMBus state machine will initialize to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device. 7.9 RESET input A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The PCA9698 registers and I2C-bus state machine will be held in their default state until the RESET input is once again HIGH. 7.10 Interrupt output (INT) The open-drain active LOW interrupt is activated when one of the port pins changes state and the port pin is configured as an input and the interrupt on it is not masked. The interrupt is deactivated when the port pin input returns to its previous state or the Input Port register is read. It is highly recommended to program the MSK register, and the IOC registers during the initialization sequence after power-up, since any change to them during Normal mode operation may cause undesirable interrupt events to happen. Remark: Changing an I/O from an output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. Only a Read of the Input Port register that contains the bit(s) image of the input(s) that generated the interrupt clears the interrupt condition. If more than one input register changed state before a read of the Input Port register is initiated, the interrupt is cleared when all the input registers containing all the inputs that changed are read. Example: If IO0_5, IO2_3, and IO3_7 change state at the same time, the interrupt is cleared only when INREG0, INREG2, and INREG3 are read. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 18 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.11 SMBus Alert output (SMBALERT) The interrupt output pin (INT) can also be used as an Alert line (SMBALERT). The SMBALERT pins of multiple devices with this feature can be connected together to form a wired-AND signal and can be used in conjunction with the SMBus Alert Response Address. ‘SMBus Alert’ message is 2 bytes long and allows the master to determine which device generated the Alert (SMBALERT going LOW). When SMBA bit = 1 (register 2Ah, bit 4), the PCA9698 supports the SMBus Alert function and its INT/SMBALERT pin may be connected as an SMBus Alert signal. When a master device senses that an ‘SMBus Alert’ condition is present on the ALERT line (SMBALERT pin of the PCA9698 and/or other devices going LOW): • It accesses the slave device(s) through the Alert Response Address (ARA) associated with a Read Command: Start − 0001 100 + R/W = 1. • If the PCA9698 is the device that generated the ‘SMBus Alert’ condition (and its SMBA bit = 1), it will acknowledge the SMBus Alert command and respond by transmitting its slave address on the SDA line. The 8th bit (LSB) of the slave address byte will be a zero. • The device will acknowledge an ARA command only if the SMBALERT signal has been previously asserted (SMBALERT = LOW). • If more than one device pulls its SMBALERT pin LOW, the highest priority (lowest I2C-bus address) device will win communication rights via standard I2C-bus arbitration during the slave address transfer. • If the PCA9698 wins the arbitration, its SMBALERT pin will become inactive (will go HIGH) at the completion of the slave address transmission (9th clock pulse, NACK phase). • If the PCA9698 loses the arbitration, its SMBALERT pin will remain active (will stay LOW). • The master ends the sequence by sending a NACK and then STOP command. • If the SMBALERT is still LOW after transfer is complete, it means that more than one device made the request. Another full transaction is then required. Remark: If the master initiates an ‘SMBus Alert’ sequence with a Write Command, none of the slave devices acknowledge. The SMBALERT is open-drain and requires a pull-up resistor to VDD. Remark: If the master sends an ACK after reading the I2C-bus slave address, the slave device keeps sending ‘1’s until a NACK is received. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 19 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.12 Output enable input (OE) The configurable active LOW or active HIGH output enable pin allows to enable or disable all the I/Os at the same time. • When a LOW level is applied to the OE pin, with OEPOL = 0 (register 2Ah, bit 4) or a HIGH level is applied to the OE pin, with OEPOL = 1 (register 2Ah, bit 0), all the I/Os configured as outputs are enabled and the logic value programmed in their respective OP registers is applied to the pins. • When a HIGH level is applied to the OE pin, with OEPOL = 0 (register 2Ah, bit 0) or a LOW level is applied to the OE pin, with OEPOL = 1 (register 2Ah, bit 0), all the I/Os configured as outputs are 3-stated. For applications requiring LED blinking with brightness control, this pin can be used to control the brightness by applying a high frequency PWM signal on the OE pin. LEDs can be blinked using the Output Port registers and can be dimmed using the PWM signal on the OE pin thus controlling the brightness by adjusting the duty cycle. Default is OEPOL = 0, so if the OE pin is held HIGH, the outputs are disabled. The OE pin needs to be pulled LOW or OEPOL changed to ‘1’ to enable the outputs. It is recommended to define the required polarity of the OE input by programing the value of OEPOL before programming the configuration registers (IOC register). 7.13 Live insertion The PCA9698 is fully specified for live-insertion applications using IOFF, power-up 3-states, robust state machine, and 50 ns noise filter. The IOFF circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The power-up 3-states circuitry places the outputs in the high-impedance state during power-up and power-down, which prevents driver conflict and bus contention. The robust state machine does not respond until it sees a valid START condition and the 50 ns noise filter will filter out any insertion glitches. The PCA9698 will not cause corruption of active data on the bus nor will the device be damaged or cause damage to devices already on the bus when similar featured devices are being used. 7.14 Standby The PCA9698 goes into standby when the I2C-bus is idle. Standby supply current is lower than 1.0 μA (typical). PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 20 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 7.15 Address map Table 12. PCA9698 Product data sheet PCA9698 address map AD2 AD1 AD0 A6 A5 A4 A3 A2 A1 A0 Address VSS SCL VSS 0 0 1 0 0 0 0 20h VSS SCL VDD 0 0 1 0 0 0 1 22h VSS SDA VSS 0 0 1 0 0 1 0 24h VSS SDA VDD 0 0 1 0 0 1 1 26h VDD SCL VSS 0 0 1 0 1 0 0 28h VDD SCL VDD 0 0 1 0 1 0 1 2Ah VDD SDA VSS 0 0 1 0 1 1 0 2Ch VDD SDA VDD 0 0 1 0 1 1 1 2Eh VSS SCL SCL 0 0 1 1 0 0 0 30h VSS SCL SDA 0 0 1 1 0 0 1 32h VSS SDA SCL 0 0 1 1 0 1 0 34h VSS SDA SDA 0 0 1 1 0 1 1 36h VDD SCL SCL 0 0 1 1 1 0 0 38h VDD SCL SDA 0 0 1 1 1 0 1 3Ah VDD SDA SCL 0 0 1 1 1 1 0 3Ch VDD SDA SDA 0 0 1 1 1 1 1 3Eh VSS VSS VSS 0 1 0 0 0 0 0 40h VSS VSS VDD 0 1 0 0 0 0 1 42h VSS VDD VSS 0 1 0 0 0 1 0 44h VSS VDD VDD 0 1 0 0 0 1 1 46h VDD VSS VSS 0 1 0 0 1 0 0 48h VDD VSS VDD 0 1 0 0 1 0 1 4Ah VDD VDD VSS 0 1 0 0 1 1 0 4Ch VDD VDD VDD 0 1 0 0 1 1 1 4Eh VSS VSS SCL 0 1 0 1 0 0 0 50h VSS VSS SDA 0 1 0 1 0 0 1 52h VSS VDD SCL 0 1 0 1 0 1 0 54h VSS VDD SDA 0 1 0 1 0 1 1 56h VDD VSS SCL 0 1 0 1 1 0 0 58h VDD VSS SDA 0 1 0 1 1 0 1 5Ah VDD VDD SCL 0 1 0 1 1 1 0 5Ch VDD VDD SDA 0 1 0 1 1 1 1 5Eh All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 21 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Table 12. PCA9698 Product data sheet PCA9698 address map …continued AD2 AD1 AD0 A6 A5 A4 A3 A2 A1 A0 Address SCL SCL VSS 1 0 1 0 0 0 0 A0h SCL SCL VDD 1 0 1 0 0 0 1 A2h SCL SDA VSS 1 0 1 0 0 1 0 A4h SCL SDA VDD 1 0 1 0 0 1 1 A6h SDA SCL VSS 1 0 1 0 1 0 0 A8h SDA SCL VDD 1 0 1 0 1 0 1 AAh SDA SDA VSS 1 0 1 0 1 1 0 ACh SDA SDA VDD 1 0 1 0 1 1 1 AEh SCL SCL SCL 1 0 1 1 0 0 0 B0h SCL SCL SDA 1 0 1 1 0 0 1 B2h SCL SDA SCL 1 0 1 1 0 1 0 B4h SCL SDA SDA 1 0 1 1 0 1 1 B6h SDA SCL SCL 1 0 1 1 1 0 0 B8h SDA SCL SDA 1 0 1 1 1 0 1 BAh SDA SDA SCL 1 0 1 1 1 1 0 BCh SDA SDA SDA 1 0 1 1 1 1 1 BEh SCL VSS VSS 1 1 0 0 0 0 0 C0h SCL VSS VDD 1 1 0 0 0 0 1 C2h SCL VDD VSS 1 1 0 0 0 1 0 C4h SCL VDD VDD 1 1 0 0 0 1 1 C6h SDA VSS VSS 1 1 0 0 1 0 0 C8h SDA VSS VDD 1 1 0 0 1 0 1 CAh SDA VDD VSS 1 1 0 0 1 1 0 CCh SDA VDD VDD 1 1 0 0 1 1 1 CEh SCL VSS SCL 1 1 1 0 0 0 1 E0h SCL VSS SDA 1 1 1 0 0 1 0 E2h SCL VDD SCL 1 1 1 0 0 1 1 E4h SCL VDD SDA 1 1 1 0 1 0 0 E6h SDA VSS SCL 1 1 1 0 1 0 1 E8h SDA VSS SDA 1 1 1 0 1 1 0 EAh SDA VDD SCL 1 1 1 0 1 1 1 ECh SDA VDD SDA 1 1 1 0 0 0 1 EEh All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 22 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 8. Characteristics of the I2C-bus The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 8.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as control signals (see Figure 11). SDA SCL data line stable; data valid change of data allowed mba607 Fig 11. Bit transfer 8.1.1 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition (P) (see Figure 12.) SDA SCL S P START condition STOP condition mba608 Fig 12. Definition of START and STOP conditions PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 23 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 8.2 System configuration A device generating a message is a ‘transmitter’; a device receiving is the ‘receiver’. The device that controls the message is the ‘master’ and the devices which are controlled by the master are the ‘slaves’ (see Figure 13). SDA SCL MASTER TRANSMITTER/ RECEIVER SLAVE RECEIVER SLAVE TRANSMITTER/ RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER I2C-BUS MULTIPLEXER SLAVE 002aaa966 Fig 13. System configuration 8.3 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse; set-up and hold times must be taken into account. A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 2 S START condition 8 9 clock pulse for acknowledgement 002aaa987 Fig 14. Acknowledgement on the I2C-bus PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 24 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 8.4 Bus transactions Data is transmitted to the PCA9698 registers using ‘Write Byte’ transfers (see Figure 15, Figure 16, Figure 17, and Figure 18). Data is read from the PCA9698 registers using ‘Read Byte’ and ‘Receive Byte’ transfers (see Figure 19 and Figure 20). PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 25 of 48 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCA9698 Product data sheet acknowledge from slave acknowledge from slave slave address command register acknowledge from slave acknowledge from slave acknowledge from slave acknowledge from slave acknowledge from slave STOP condition SDA S A6 A5 A4 A3 A2 A1 A0 0 A 1 0 0 0 1 0 0 0 A DATA BANK 0 A DATA BANK 1 A DATA BANK 2 A DATA BANK 3 A DATA BANK 4 A P START condition R/W AI = 1 Output Port register bank 0 is selected write to port when OCH = 0 tv(Q) data out from port when OCH = 0 write to port when OCH = 1 tv(Q) data out from port when OCH = 1 data valid bank 0 data valid bank 1 data valid bank 2 data valid bank 3 data valid bank 4 002aab944 OE is LOW (with OEPOL = 0) or HIGH (with OEPOL = 1) to observe a change in the outputs. If more than 5 bytes are written, previous data are overwritten. Fig 15. Write to the 5 output ports PCA9698 26 of 48 © NXP B.V. 2010. All rights reserved. 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Rev. 3 — 3 August 2010 All information provided in this document is subject to legal disclaimers. data valid all banks PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT acknowledge from slave slave address SDA S A6 A5 A4 A3 A2 A1 A0 0 A AI 0 START condition 0 0 1 D2 D1 D0 A bank X determined by D2, D1, D0 acknowledge from slave DATA BANK X A P acknowledge from slave R/W STOP condition write to port tv(Q) data X valid data out from port 002aab945 OE is LOW (with OEPOL = 0) or HIGH (with OEPOL = 1) to observe a change in the outputs. OCH = 0. When OCH = 1, the change in the port happens at the acknowledge phase. Two, three, or four adjacent banks can be programmed by using the Auto-Increment feature (AI = 1) and change at the corresponding output port becomes effective at the STOP command when OCH = 0, or at each acknowledge when OCH = 1. Fig 16. Write to a specific output port acknowledge from slave slave address command register SDA S A6 A5 A4 A3 A2 A1 A0 0 A 1 START condition R/W acknowledge from slave acknowledge from slave acknowledge from slave 0 D5 D4 D3 D2 D1 D0 A DATA BANK 0 A DATA BANK 1 A 01 0000 for Polarity Inversion register programming bank 0 01 1000 for Configuration register programming bank 0 10 0000 for Mask interrupt register programming bank 0 AI = 1 acknowledge from slave acknowledge from slave acknowledge from slave DATA BANK 2 A DATA BANK 3 A DATA BANK 4 A P STOP condition 002aab946 The programing becomes effective at the Acknowledge. Less than 5 bytes can be programmed by using the same scheme. ‘D5 D4 D3 D2 D1 D0’ refers to the first register to be programmed. If more than 5 bytes are written, previous data are overwritten (the sixth configuration register will roll over to the first addressed configuration register, the sixth Polarity Inversion register will roll over to the first addressed Polarity Inversion register, the sixth Mask interrupt register will roll over to the first addressed Mask interrupt register. Fig 17. Write to the I/O Configuration, Polarity Inversion, or Mask interrupt registers (5 banks) PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 27 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT acknowledge from slave slave address command register SDA S A6 A5 A4 A3 A2 A1 A0 0 A X R/W START condition 0 1 0 1 acknowledge from slave 0 D1 D0 A acknowledge from slave DATA A P AI = 'don't care' STOP condition 00 for output structure configuration programming 01 for all bank control register programming 10 for mode selection register programming 002aab947 The programming becomes effective at the Acknowledge. If more than 1 byte is written, previous data is overwritten. Fig 18. Write to the output structure configuration, all bank control, or mode selection acknowledge from slave command register acknowledge from slave slave address SDA S A6 A5 A4 A3 A2 A1 A0 0 A 1 START condition R/W acknowledge from slave slave address 0 D5 D4 D3 D2 D1 D0 A Sr A6 A5 A4 A3 A2 A1 A0 1 A AI = 1 repeated START condition R/W D[5:0] = 00 0000 for Input Port register bank 0 D[5:0] = 00 1000 for Output Port register bank 0 D[5:0] = 01 0000 for Polarity Inversion register bank 0 D[5:0] = 01 1000 for Configuration register bank 0 D[5:0] = 10 0000 for Mask Interrupt register bank 0 data from register DATA first byte register determined by D4 D3 D2 D1 D0 A data from register data from register DATA DATA second byte last byte no acknowledge from master A P STOP condition acknowledge from master 002aab948 If AI = 0, the same register is read during the whole sequence. If AI = 1, the register value is incremented after each read. When the last register bank is read, it rolls over to the first byte of the category (see category definition in Section 7.3 “Command register”). The INT signal is released only when the last register containing an input that changed has been read. For example, when IO2_4 and IO4_7 change at the same time and an Input Port register read sequence is initiated, starting with IP0, INT is released after IP4 is read (and not after IP2 is read). Fig 19. Read from Input Port, Output Port, I/O Configuration, Polarity Inversion, or Mask interrupt registers PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 28 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT acknowledge from slave slave address SDA S A6 A5 A4 A3 A2 A1 A0 0 A X R/W START condition acknowledge from slave slave address acknowledge from slave command register 0 1 0 1 no acknowledge from master data from register DATA 0 D1 D0 A Sr A6 A5 A4 A3 A2 A1 A0 1 A AI = 'don't care' repeated START condition last byte R/W 00 for output structure configuration register reading 01 for for all bank control register reading 10 for mode selection register reading A P STOP condition At this moment master-transmitter becomes master-receiver, and slave-receiver becomes slave-transmitter. 002aab949 If AI = 0 or 1, the same register is read during the all sequence. Fig 20. Read from output structure configuration, all bank control or mode selection registers acknowledge from slave that generated the alert S 0 0 0 1 1 START condition 0 no acknowledge from master PCA9698 I2C-bus slave address SMBus Alert response address 0 1 A A6 A5 A4 A3 A2 A1 A0 0 A P R/W R/W STOP condition At this moment master-transmitter becomes master-receiver and slave receiver becomes slave-transmitter. SMBALERT signal is released (assuming that only one device generated the alert) SMBALERT 002aab950 Fig 21. SMBus Alert procedure acknowledge from one or several slaves Device ID address S 1 1 1 1 1 0 START condition 0 I2C-bus slave address of the device to be identified acknowledge from slave to be identified Device ID address 0 A A6 A5 A4 A3 A2 A1 A0 0 A Sr 1 R/W don't care acknowledge from master 1 1 1 repeated START condition acknowledge from master 1 0 acknowledge from slave to be identified 0 1 A R/W no acknowledge from master M M M9 M8 M7 M6 M5 M4 A M3 M2 M1 M0 P8 P7 P6 P5 A P4 P3 P2 P1 P0 R2 R1 R0 A P 11 10 STOP condition manufacturer name = 000000000000 part identification = 000000000 revision = 000 002aab951 If more than 3 bytes are read, the slave device loops back to the first byte (manufacturer byte) and keeps sending data until the master generates a ‘No Acknowledge’. Fig 22. Device ID field reading PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 29 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT acknowledge from slave GPIO All Call address SDA S 1 1 0 1 1 1 0 START condition 0 A 1 R/W acknowledge from slave(s) command register acknowledge from slave(s) acknowledge from slave(s) 0 D5 D4 D3 D2 D1 D0 A DATA BANK 0 A DATA BANK 1 A 00 1000 for Output Port register programming bank 0 01 0000 for Polarity Inversion register programming bank 0 01 1000 for Configuration register programming bank 0 10 0000 for Mask interrupt register programming bank 0 AI = 1 acknowledge from slave(s) acknowledge from slave(s) acknowledge from slave DATA BANK 2 A DATA BANK 3 A DATA BANK 4 A P STOP condition 002aab952 Only slave devices with bit IOAC = 1 answer to the GPIO All Call transaction. Output Port register programming becomes effective at the STOP command if OCH = 0, at each acknowledge if OCH = 1. Configuration, Polarity Inversion, and Mask interrupt registers become effective at the acknowledge. Less than 5 bytes can be programmed by using the same scheme. ‘D5 D4 D3 D2 D1 D0’ refers to the first register to be programmed. If more than 5 bytes are written, previous data are overwritten (the sixth Configuration register will roll over to the first addressed Configuration register, the sixth Polarity Inversion register will roll over to the first addressed Polarity Inversion register, the sixth Mask interrupt register will roll over to the first addressed Mask interrupt register). Fig 23. GPIO All Call write to the Output Port, I/O Configuration, Polarity Inversion, or Mask interrupt registers acknowledge from slave(s) acknowledge from slave(s) slave address SDA S 1 1 0 1 START condition 1 acknowledge from slave(s) command register 1 0 0 A X R/W 0 1 0 1 0 D1 D0 A AI = 'don't care' DATA A P STOP condition 00 for Output structure configuration register programming 01 for All Bank Control register programming 10 for Mode selection register programming 002aab953 Only slave devices with bit 0 IOAC = 1 answer the GPIO All Call transaction. The programming becomes effective at the acknowledge. If more than 1 byte is written, previous data is overwritten. Fig 24. GPIO All Call write to the Output structure configuration, All Bank Control, or Mode selection registers PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 30 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 9. Application design-in information 5V VDD 1.6 kΩ 1.6 kΩ 1.1 kΩ (optional) 2 kΩ 2 kΩ 1.1 kΩ (optional) VDD VDD MASTER CONTROLLER SCL PCA9698 SCL IO0_0 SUBSYSTEM 1 (e.g., temp. sensor) SDA SDA IO0_1 INT RESET IO0_2 RESET INT INT/SMBALERT IO0_3 OE OE RESET SUBSYSTEM 2 (e.g., counter) IO0_4 VSS IO0_5 A IO1_0 controlled switch (e.g., CBT device) enable IO3_7 IO4_0 B IO4_7 ALARM AD2 SUBSYSTEM 3 (e.g., alarm system) AD1 AD0 VDD VSS 24 LED MATRIX ALPHANUMERIC KEYPAD 002aab954 Device address configured as ‘0100 000x’ for this example. IO0_0, IO0_2, IO0_3, IO1_0 to IO3_7 are configured as outputs. IO0_1, IO0_4, IO4_0 to IO4_7 are configured as inputs. Fig 25. Typical application PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 31 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 10. Limiting values Table 13. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). PCA9698 Product data sheet Symbol Parameter Conditions VDD supply voltage VI input voltage VSS − 0.5 5.5 V II input current - ±20 mA VI/O voltage on an input/output pin VSS − 0.5 5.5 V IO(IOx_y) output current on pin IOx_y −20 +50 mA IDD supply current - 500 mA ISS ground supply current - 1100 mA Ptot total power dissipation - 500 mW Tstg storage temperature −65 +150 °C Tamb ambient temperature operating −40 +85 °C Tj junction temperature operating - 125 °C storage - 150 °C All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 Min Max Unit −0.5 +6 V © NXP B.V. 2010. All rights reserved. 32 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 11. Static characteristics Table 14. Static characteristics VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 2.3 - 5.5 V VDD = 2.3 V - 135 200 μA VDD = 3.3 V - 250 400 μA VDD = 5.5 V - 550 800 μA VDD = 2.3 V - 0.15 11 μA VDD = 3.3 V - 0.25 12 μA - 0.75 15.5 μA - 1.70 2.0 V Supplies VDD supply voltage IDD supply current Istb standby current Operating mode; no load; fSCL = 1 MHz; AD0, AD1, AD2 = static H or L no load; fSCL = 0 kHz; I/O = inputs; VI = VDD VDD = 5.5 V VPOR power-on reset voltage no load; VI = VDD or VSS [1] Input SCL; input/output SDA VIL LOW-level input voltage −0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 5.5 V IOL LOW-level output current VOL = 0.4 V 20 - - mA IL leakage current VI = VDD or VSS −1 - +1 μA Ci input capacitance VI = VSS - 5 10 pF −0.5 - +0.3VDD V I/Os VIL LOW-level input voltage VIH HIGH-level input voltage IOL LOW-level output current IOL(tot) VOH total LOW-level output current HIGH-level output voltage 2 - 5.5 V VOL = 0.5 V; VDD = 2.3 V [2] 12 - - mA VOL = 0.5 V; VDD = 3.0 V [2] 17 - - mA VOL = 0.5 V; VDD = 4.5 V [2] 25 - - mA TSSOP56 package [2] - - 0.86 A HVQFN56 package [2] - - 1.0 A IOH = −10 mA; VDD = 2.3 V 1.6 - - V IOH = −10 mA; VDD = 3.0 V 2.3 - - V IOH = −10 mA; VDD = 4.5 V 4.0 - - V VOL = 0.5 V; VDD = 4.5 V ILIH HIGH-level input leakage current VDD = 3.6 V; VI/O = VDD −1 - +1 μA ILIL LOW-level input leakage current VDD = 5.5 V; VI/O = VSS −1 - +1 μA Ci input capacitance - 6 7 pF Co output capacitance - 6 7 pF PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 33 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Table 14. Static characteristics …continued VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit VOL = 0.4 V 6 - - mA - 3 5 pF Interrupt INT IOL LOW-level output current Co output capacitance Inputs RESET and OE VIL LOW-level input voltage −0.5 - +0.8 V VIH HIGH-level input voltage 2 - 5.5 V ILI input leakage current −1 - +1 μA Ci input capacitance - 3 5 pF −0.5 - +0.3VDD V Inputs AD0, AD1, AD2 VIL LOW-level input voltage VIH HIGH-level input voltage 0.7VDD - 5.5 V ILI input leakage current −1 - +1 μA Ci input capacitance - 3.5 5 pF [1] VDD must be lowered to 0.2 V in order to reset part. [2] Each bit must be limited to a maximum of 25 mA and the total package limited to the package maximum limit due to internal busing limits. 11.1 Performance curves 002aab955 1.2 IDD (μA) 002aab956 1.2 IDD (μA) VDD = 5 V 0.8 VDD = 5 V 0.8 3.3 V 3.3 V 0.4 0.4 2.3 V 0 −50 0 50 2.3 V 100 Tamb (°C) fSCL = 400 kHz; all I/Os unloaded Product data sheet 0 50 100 Tamb (°C) SCL = VDD; all I/Os unloaded Fig 26. Supply current as a function of temperature PCA9698 0 −50 Fig 27. Standby current as a function of temperature All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 34 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 002aab957 600 IDD (μA) 002aab958 50 Isink (mA) 40 Tamb = −40 °C +25 °C +85 °C 400 30 fSCL = 1 MHz 20 200 400 kHz 10 100 kHz 0 2.0 0 3.0 4.0 5.0 6.0 0 0.2 0.4 VDD (V) 0.6 VOL (V) All I/Os unloaded; address pins static HIGH or LOW Fig 28. Supply current as a function of supply voltage 002aab959 50 Isink (mA) 40 Tamb = −40 °C +25 °C +85 °C 30 Fig 29. I/O sink current as a function of LOW-level output voltage (VDD = 2.3 V) 002aab960 50 Isink (mA) 40 Tamb = −40 °C +25 °C +85 °C 30 20 20 10 10 0 0 0 0.2 0.4 0.6 0 0.2 0.4 VOL (V) Fig 30. I/O sink current as a function of LOW-level output voltage (VDD = 3.0 V) 002aab961 30 Isource (mA) Tamb = −40 °C +25 °C +85 °C 20 0.6 VOL (V) Fig 31. I/O sink current as a function of LOW-level output voltage (VDD = 4.5 V) 002aab962 50 Isource (mA) 40 Tamb = −40 °C +25 °C +85 °C 30 20 10 10 0 0 0 0.2 0.4 0.6 0.8 VDD − VOH (V) Fig 32. I/O source current as a function of HIGH-level output voltage (VDD = 2 V) PCA9698 Product data sheet 0 0.2 0.4 0.6 0.8 VDD − VOH (V) Fig 33. I/O source current as a function of HIGH-level output voltage (VDD = 3.3 V) All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 35 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 002aab965 50 Isource (mA) 40 002aab963 400 Tamb = −40 °C +25 °C +85 °C VOL (mV) 300 (1) 30 200 20 (2) 100 10 (3) 0 0.2 (4) 0 −50 0 0.4 0.6 VDD − VOH (V) 0 50 100 Tamb (°C) (1) VDD = 5 V; Isink = 10 mA (2) VDD = 2.3 V; Isink = 10 mA (3) VDD = 5 V; Isink = 1 mA (4) VDD = 2.3 V; Isink = 1 mA Fig 34. I/O source current as a function of HIGH-level output voltage (VDD = 5 V) Fig 35. I/O LOW-level output voltage as a function of temperature 002aab964 600 VDD − VOH (V) 400 (1) 200 (2) 0 −50 0 50 100 Tamb (°C) (1) VDD = 2.3 V; Isource = 10 mA (2) VDD = 5 V; Isource = 10 mA Fig 36. HIGH-level output voltage as a function of temperature PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 36 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 12. Dynamic characteristics Table 15. Dynamic characteristics Symbol Parameter Conditions Standard-mode I2C-bus [3] Min Max Fast-mode I2C-bus Fast-mode Plus Unit I2C-bus Min Max Min Max fSCL SCL clock frequency 0 100 0 400 0 1000 tBUF bus free time between a STOP and START condition 4.7 - 1.3 - 0.5 - kHz μs tHD;STA hold time (repeated) START condition 4.0 - 0.6 - 0.26 - μs tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - 0.26 - μs tSU;STO set-up time for STOP condition 4.0 - 0.6 - 0.26 - μs tHD;DAT data hold time 0 - 0 - 0 - ns 0.1 3.45 0.1 0.9 0.05 0.45 μs 300 - 75 - 75 450 ns tVD;ACK data valid acknowledge time [1] tVD;DAT data valid time [2] tSU;DAT data set-up time 250 - 100 - 50 - ns tLOW LOW period of the SCL clock 4.7 - 1.3 - 0.5 - μs tHIGH HIGH period of the SCL clock 4.0 - 0.6 - 0.26 - μs tf fall time of both SDA and SCL signals [4][6] - 300 20 + 0.1Cb[5] 300 - 120 ns tr rise time of both SDA and SCL signals [4][6] - 1000 20 + 0.1Cb[5] 300 - 120 ns tSP pulse width of spikes that must be suppressed by the input filter [7] - 50 - 50 - 50 ns - 80 - 80 - 80 ns Port timing ten enable time output tdis disable time output - 40 - 40 - 40 ns tv(Q) data output valid time - 250 - 250 - 250 ns tsu(D) data input set-up time 100 - 100 - 100 - ns th(D) data input hold time 250 - 250 - 250 - ns valid time on pin INT - 4 - 4 - 4 μs trst(INT_N) reset time on pin INT - 4 - 4 - 4 μs Interrupt timing tv(INT_N) Reset tw(rst) reset pulse width 4 - 4 - 4 - ns trec(rst) reset recovery time 0 - 0 - 0 - ns trst reset time 100 - 100 - 100 - ns [1] tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA (out) LOW. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 37 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT [2] tVD;DAT = minimum time for SDA data out to be valid following SCL LOW. [3] Minimum SCL clock frequency is limited by the bus time-out feature, which resets the serial bus interface if either SDA or SCL is held LOW for a minimum of 25 ms. Disable bus time-out feature for DC operation. [4] A master device must internally provide a hold time of at least 300 ns for the SDA signal (refer to the VIL of the SCL signal) in order to bridge the undefined region of SCL’s falling edge. [5] Cb = total capacitance of one bus line in pF. [6] The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA output stage tf is specified at 250 ns. This allows series protection resistors to be connected between the SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf. [7] Input filters on the SDA and SCL inputs suppress noise spikes less than 50 ns. SDA tr tBUF tf tHD;STA tSP tLOW SCL tHD;STA P tSU;STA tHD;DAT S tHIGH tSU;DAT tSU;STO Sr P 002aaa986 Fig 37. Definition of timing on the I2C-bus protocol START condition (S) tSU;STA bit 7 MSB (A7) tLOW bit 6 (A6) tHIGH bit 0 (R/W) acknowledge (A) STOP condition (P) 1/f SCL SCL tBUF tf tr SDA tSU;DAT tHD;STA tHD;DAT tVD;DAT tVD;ACK tSU;STO 002aab175 Rise and fall times refer to VIL and VIH. Fig 38. I2C-bus timing diagram PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 38 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT ACK or read cycle START SCL SDA 30 % trst RESET 50 % 50 % 50 % trec(rst) tw(rst) trst 50 % IOx_y output off 002aac018 Fig 39. Reset timing 13. Test information VDD PULSE GENERATOR VI VO RL 500 Ω 2VDD open VSS DUT RT CL 50 pF 500 Ω 002aac019 RL = load resistance. CL = load capacitance includes jig and probe capacitance. RT = termination resistance should be equal to the output impedance Zo of the pulse generators. Fig 40. Test circuitry for switching times PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 39 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 14. Package outline TSSOP56: plastic thin shrink small outline package; 56 leads; body width 6.1 mm SOT364-1 E D A X c HE y v M A Z 56 29 Q A2 (A 3) A1 pin 1 index A θ Lp L 1 detail X 28 w M bp e 2.5 0 5 mm scale DIMENSIONS (mm are the original dimensions). UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z θ mm 1.2 0.15 0.05 1.05 0.85 0.25 0.28 0.17 0.2 0.1 14.1 13.9 6.2 6.0 0.5 8.3 7.9 1 0.8 0.4 0.50 0.35 0.25 0.08 0.1 0.5 0.1 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT364-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-153 Fig 41. Package outline SOT364-1 (TSSOP56) PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 40 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT HVQFN56: plastic thermal enhanced very thin quad flat package; no leads; 56 terminals; body 8 x 8 x 0.85 mm A B D SOT684-1 terminal 1 index area A E A1 c detail X C e1 e 1/2 e b 15 L y y1 C v M C A B w M C 28 29 14 e e2 Eh 1/2 1 e 42 terminal 1 index area 56 43 X Dh 0 2.5 scale DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. A1 b 1 0.05 0.00 0.30 0.18 5 mm c D(1) Dh E(1) Eh 0.2 8.1 7.9 4.45 4.15 8.1 7.9 4.45 4.15 e e1 6.5 0.5 e2 L v w y y1 6.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT684-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 42. Package outline SOT684-1 (HVQFN56) PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 41 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 15. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling ensure that the appropriate precautions are taken as described in JESD625-A or equivalent standards. 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 16.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 16.3 Wave soldering Key characteristics in wave soldering are: PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 42 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 16.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 43) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 16 and 17 Table 16. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 Table 17. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 43. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 43 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 43. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 17. Abbreviations Table 18. PCA9698 Product data sheet Abbreviations Acronym Description CDM Charged Device Model DUT Device Under Test ESD ElectroStatic Discharge GPIO General Purpose Input/Output HBM Human Body Model I2C-bus Inter-Integrated Circuit bus LED Light Emitting Diode MM Machine Model PICMG PCI Industrial Computer Manufacturers Group PLC Programmable Logic Controller POR Power-On Reset PWM Pulse Width Modulation RAID Redundant Array of Independent Discs SMBus System Management Bus All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 44 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 18. Revision history Table 19. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9698 v.3 20100803 Product data sheet - PCA9698 v.2 Modifications: • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • • Legal texts have been adapted to the new company name where appropriate. • Figure 25 “Typical application”: text below figure corrected from “Device address configured as ‘0010 000x’ for this example.” to “Device address configured as ‘0100 000x’ for this example.” Table 14 “Static characteristics”, sub-section “Inputs RESET and OE” is corrected by removing IOH specification. PCA9698 v.2 20060719 Product data sheet - PCA9698_1 PCA9698 v.1 (9397 750 13751) 20060224 Product data sheet - - PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 45 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 19. Legal information 19.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 19.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 19.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 46 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. 19.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 20. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9698 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 3 August 2010 © NXP B.V. 2010. All rights reserved. 47 of 48 PCA9698 NXP Semiconductors 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT 21. Contents 1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 Functional description . . . . . . . . . . . . . . . . . . . 7 Device address . . . . . . . . . . . . . . . . . . . . . . . . . 7 Alert response, GPIO All Call and Device ID addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7.3 Command register . . . . . . . . . . . . . . . . . . . . . . 8 7.3.1 5-bank register category . . . . . . . . . . . . . . . . . . 9 7.3.2 1-bank register category . . . . . . . . . . . . . . . . . . 9 7.4 Register definitions . . . . . . . . . . . . . . . . . . . . . . 9 7.4.1 IP0 to IP4 - Input Port registers . . . . . . . . . . . 11 7.4.2 OP0 to OP4 - Output Port registers . . . . . . . . 11 7.4.3 PI0 to PI4 - Polarity Inversion registers . . . . . 12 7.4.4 IOC0 to IOC4 - I/O Configuration registers. . . 12 7.4.5 MSK0 to MSK4 - Mask interrupt registers . . . 13 7.4.6 OUTCONF - output structure configuration register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.4.7 ALLBNK - All Bank control register. . . . . . . . . 14 7.4.7.1 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.4.8 MODE - PCA9698 mode selection register . . 15 7.5 Device ID - PCA9698 ID field . . . . . . . . . . . . . 16 7.6 GPIO All Call . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.7 Output state change on ACK or STOP . . . . . . 17 7.8 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 18 7.9 RESET input . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.10 Interrupt output (INT) . . . . . . . . . . . . . . . . . . . 18 7.11 SMBus Alert output (SMBALERT) . . . . . . . . . 19 7.12 Output enable input (OE) . . . . . . . . . . . . . . . . 20 7.13 Live insertion . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.14 Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.15 Address map . . . . . . . . . . . . . . . . . . . . . . . . . 21 8 Characteristics of the I2C-bus . . . . . . . . . . . . 23 8.1 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.1.1 START and STOP conditions . . . . . . . . . . . . . 23 8.2 System configuration . . . . . . . . . . . . . . . . . . . 24 8.3 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 24 8.4 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . 25 9 Application design-in information . . . . . . . . . 31 10 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 32 11 Static characteristics. . . . . . . . . . . . . . . . . . . . 33 11.1 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 19 19.1 19.2 19.3 19.4 20 21 Performance curves. . . . . . . . . . . . . . . . . . . . Dynamic characteristics. . . . . . . . . . . . . . . . . Test information . . . . . . . . . . . . . . . . . . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Handling information . . . . . . . . . . . . . . . . . . . Soldering of SMD packages . . . . . . . . . . . . . . Introduction to soldering. . . . . . . . . . . . . . . . . Wave and reflow soldering. . . . . . . . . . . . . . . Wave soldering . . . . . . . . . . . . . . . . . . . . . . . Reflow soldering . . . . . . . . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 37 39 40 42 42 42 42 42 43 44 45 46 46 46 46 47 47 48 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 3 August 2010 Document identifier: PCA9698