Important notice
Dear Customer,
On 7 February 2017 the former NXP Standard Product business became a new company with the
tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic and PowerMOS
semiconductors with its focus on the automotive, industrial, computing, consumer and wearable
application markets
In data sheets and application notes which still contain NXP or Philips Semiconductors references, use
the references to Nexperia, as shown below.
Instead of http://www.nxp.com, http://www.philips.com/ or http://www.semiconductors.philips.com/,
use http://www.nexperia.com
Instead of sales.addresses@www.nxp.com or sales.addresses@www.semiconductors.philips.com, use
salesaddresses@nexperia.com (email)
Replace the copyright notice at the bottom of each page or elsewhere in the document, depending on
the version, as shown below:
- © NXP N.V. (year). All rights reserved or © Koninklijke Philips Electronics N.V. (year). All rights
reserved
Should be replaced with:
- © Nexperia B.V. (year). All rights reserved.
If you have any questions related to the data sheet, please contact our nearest sales office via e-mail
or telephone (details via salesaddresses@nexperia.com). Thank you for your cooperation and
understanding,
Kind regards,
Team Nexperia
PDTA114E series
PNP resistor-equipped transistors;
R1 = 10 k, R2 = 10 k
Rev. 10 — 21 December 2011
Product data sheet
1. Product profile
1.1 General description
PNP Resistor-Equipped Transistor (RET) family in small Surface-Mounted Device (SMD)
plastic packages.
Table 1.
Product overview
Type number
Package
JEDEC
NPN
complement
Package
configuration
NXP
JEITA
PDTA114EE
SOT416
SC-75
-
PDTC114EE
ultra small
PDTA114EM
SOT883
SC-101
-
PDTC114EM
leadless ultra small
PDTA114ET
SOT23
-
TO-236AB PDTC114ET
small
PDTA114EU
SOT323
SC-70
-
very small
PDTC114EU
1.2 Features and benefits
100 mA output current capability
Built-in bias resistors
Simplifies circuit design
Reduces component count
Reduces pick and place costs
AEC-Q101 qualified
1.3 Applications
Digital application in automotive and
industrial segments
Control of IC inputs
Cost-saving alternative for BC847/857
series in digital applications
Switching loads
1.4 Quick reference data
Table 2.
Quick reference data
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VCEO
collector-emitter voltage
open base
-
-
50
V
IO
output current
-
-
100
mA
R1
bias resistor 1 (input)
7
10
13
k
R2/R1
bias resistor ratio
0.8
1.0
1.2
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
2. Pinning information
Table 3.
Pinning
Pin
Description
Simplified outline
Graphic symbol
SOT23; SOT323; SOT416
1
input (base)
2
GND (emitter)
3
3
3
R1
output (collector)
1
R2
1
2
2
006aaa144
sym003
SOT883
1
input (base)
2
GND (emitter)
3
1
3
3
2
output (collector)
R1
1
Transparent
top view
R2
2
sym003
3. Ordering information
Table 4.
Ordering information
Type number
Package
Name
Description
Version
PDTA114EE
SC-75
plastic surface-mounted package; 3 leads
SOT416
PDTA114EM
SC-101
leadless ultra small plastic package; 3 solder lands; SOT883
body 1.0 0.6 0.5 mm
PDTA114ET
-
plastic surface-mounted package; 3 leads
SOT23
PDTA114EU
SC-70
plastic surface-mounted package; 3 leads
SOT323
4. Marking
Table 5.
Type number
Marking code[1]
PDTA114EE
03
PDTA114EM
E5
PDTA114ET
*03
PDTA114EU
*03
[1]
PDTA114E_SER
Product data sheet
Marking codes
* = placeholder for manufacturing site code.
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
2 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
5. Limiting values
Table 6.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
Max
Unit
VCBO
collector-base voltage
open emitter
-
50
V
VCEO
collector-emitter voltage
open base
-
50
V
VEBO
emitter-base voltage
open collector
-
10
V
VI
input voltage
-
+40
V
positive
PDTA114E_SER
Product data sheet
negative
-
10
V
IO
output current
-
100
mA
ICM
peak collector current
single pulse; tp 1 ms
-
100
mA
Ptot
total power dissipation
Tamb 25 C
PDTA114EE (SOT416)
[1][2]
-
150
mW
PDTA114EM (SOT883)
[2][3]
-
250
mW
PDTA114ET (SOT23)
[1]
-
250
mW
PDTA114EU (SOT323)
[1]
-
200
mW
Tj
junction temperature
-
150
C
Tamb
ambient temperature
65
+150
C
Tstg
storage temperature
65
+150
C
[1]
Device mounted on an FR4 Printed-Circuit Board (PCB), single-sided copper, tin-plated and standard
footprint.
[2]
Reflow soldering is the only recommended soldering method.
[3]
Device mounted on an FR4 PCB with 70 m copper strip line, standard footprint.
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
3 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
006aac778
300
Ptot
(mW)
(1)
(2)
200
(3)
100
0
-75
-25
25
75
125
175
Tamb (°C)
(1) SOT23; FR4 PCB, standard footprint
SOT883; FR4 PCB with 70 m copper strip line, standard footprint
(2) SOT323; FR4 PCB, standard footprint
(3) SOT416; FR4 PCB, standard footprint
Fig 1.
Power derating curves
6. Thermal characteristics
Table 7.
PDTA114E_SER
Product data sheet
Thermal characteristics
Symbol
Parameter
Conditions
Rth(j-a)
thermal resistance from junction
to ambient
in free air
Min
Typ
Max
Unit
PDTA114EE (SOT416)
[1][2]
-
-
830
K/W
PDTA114EM (SOT883)
[2][3]
-
-
500
K/W
PDTA114ET (SOT23)
[1]
-
-
500
K/W
PDTA114EU (SOT323)
[1]
-
-
625
K/W
[1]
Device mounted on an FR4 PCB, single-sided copper, tin-plated and standard footprint.
[2]
Reflow soldering is the only recommended soldering method.
[3]
Device mounted on an FR4 PCB with 70 m copper strip line, standard footprint.
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
4 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
006aac781
103
duty cycle = 1
Zth(j-a)
(K/W)
0.75
0.5
0.33
0.2
102
0.1
0.05
0.02
10
0.01
0
1
10-5
10-4
10-3
10-2
10-1
1
10
102
103
tp (s)
FR4 PCB, standard footprint
Fig 2.
Transient thermal impedance from junction to ambient as a function of pulse duration for
PDTA114EE (SOT416); typical values
006aac782
103
Zth(j-a)
(K/W)
duty cycle = 1
0.75
0.5
102
0.33
0.2
0.1
0.05
10
0.02
0.01
0
1
10-5
10-4
10-3
10-2
10-1
1
10
102
103
tp (s)
FR4 PCB, 70 m copper strip line
Fig 3.
Transient thermal impedance from junction to ambient as a function of pulse duration for
PDTA114EM (SOT883); typical values
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
5 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
006aac779
103
duty cycle = 1
Zth(j-a)
(K/W)
0.75
0.5
0.33
102
0.2
0.1
0.05
0.02
10
0.01
0
1
10-5
10-4
10-3
10-2
10-1
1
10
102
103
tp (s)
FR4 PCB, standard footprint
Fig 4.
Transient thermal impedance from junction to ambient as a function of pulse duration for
PDTA114ET (SOT23); typical values
006aac780
103
duty cycle = 1
Zth(j-a)
(K/W)
0.75
0.5
0.33
102
0.2
0.1
0.05
0.02
10
0.01
0
1
10-5
10-4
10-3
10-2
10-1
1
10
102
103
tp (s)
FR4 PCB, standard footprint
Fig 5.
Transient thermal impedance from junction to ambient as a function of pulse duration for
PDTA114EU (SOT323); typical values
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
6 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
7. Characteristics
Table 8.
Characteristics
Tamb = 25 C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
ICBO
collector-base
cut-off current
VCB = 50 V; IE = 0 A
-
-
100
nA
ICEO
collector-emitter
cut-off current
VCE = 30 V; IB = 0 A
-
-
1
A
VCE = 30 V; IB = 0 A;
Tj = 150 C
-
-
5
A
A
IEBO
emitter-base
cut-off current
VEB = 5 V; IC = 0 A
-
-
400
hFE
DC current gain
VCE = 5 V; IC = 5 mA
30
-
-
VCEsat
collector-emitter
saturation voltage
IC = 10 mA;
IB = 0.5 mA
-
-
150
mV
VI(off)
off-state input
voltage
VCE = 5 V;
IC = 100 A
-
1.1
0.8
V
VI(on)
on-state input
voltage
VCE = 0.3 V;
IC = 10 mA
2.5
1.8
-
V
R1
bias resistor 1 (input)
7
10
13
k
R2/R1
bias resistor ratio
0.8
1.0
1.2
Cc
collector capacitance VCB = 10 V;
IE = ie = 0 A; f = 1 MHz
-
-
3
pF
fT
transition frequency
-
180
-
MHz
[1]
PDTA114E_SER
Product data sheet
VCE = 5 V;
IC = 10 mA;
f = 100 MHz
[1]
Characteristics of built-in transistor.
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
7 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
006aac773
103
hFE
006aac774
-1
(1)
VCEsat
(V)
(2)
(3)
102
-10-1
(1)
10
(2)
(3)
1
-10-1
-1
-102
-10
-10-2
-1
-102
-10
IC (mA)
IC (mA)
VCE = 5 V
IC/IB = 20
(1) Tamb = 100 C
(1) Tamb = 100 C
(2) Tamb = 25 C
(2) Tamb = 25 C
(3) Tamb = 40 C
(3) Tamb = 40 C
Fig 6.
DC current gain as a function of collector
current; typical values
Fig 7.
006aac775
-10
Collector-emitter saturation voltage as a
function of collector current; typical values
006aac776
-10
VI(off)
(V)
VI(on)
(V)
(1)
(1)
(2)
(2)
-1
-1
(3)
-10-1
-10-1
-1
-102
-10
(3)
-10-1
-10-1
IC (mA)
VCE = 0.3 V
VCE = 5 V
(1) Tamb = 40 C
(2) Tamb = 25 C
(2) Tamb = 25 C
(3) Tamb = 100 C
(3) Tamb = 100 C
On-state input voltage as a function of
collector current; typical values
PDTA114E_SER
Product data sheet
-10
IC (mA)
(1) Tamb = 40 C
Fig 8.
-1
Fig 9.
Off-state input voltage as a function of
collector current; typical values
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
8 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
006aac777
6
Cc
(pF)
006aac763
103
fT
(MHz)
4
102
2
0
0
-10
-20
-30
-40
-50
VCB (V)
f = 1 MHz; Tamb = 25 C
10
-10-1
-1
-102
-10
IC (mA)
VCE = 5 V; Tamb = 25 C
Fig 10. Collector capacitance as a function of
collector-base voltage; typical values
Fig 11. Transition frequency as a function of collector
current; typical values of built-in transistor
8. Test information
8.1 Quality information
This product has been qualified in accordance with the Automotive Electronics Council
(AEC) standard Q101 - Stress test qualification for discrete semiconductors, and is
suitable for use in automotive applications.
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
9 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
9. Package outline
0.62
0.55
0.55
0.47
0.95
0.60
1.8
1.4
3
0.45
0.15
0.50
0.46
3
0.30
0.22
1.75 0.9
1.45 0.7
1.02
0.95
0.65
1
0.30
0.22
2
0.30
0.15
0.25
0.10
2
1
0.20
0.12
1
0.35
Dimensions in mm
04-11-04
Fig 12. Package outline PDTA114EE (SOT416/SC-75)
3.0
2.8
Dimensions in mm
03-04-03
Fig 13. Package outline PDTA114EM (SOT883/SC-101)
1.1
0.9
2.2
1.8
1.1
0.8
0.45
0.15
3
3
0.45
0.15
2.5 1.4
2.1 1.2
2.2 1.35
2.0 1.15
1
1
2
0.48
0.38
1.9
Dimensions in mm
0.25
0.10
1.3
04-11-04
Fig 14. Package outline PDTA114ET (SOT23)
2
0.4
0.3
0.15
0.09
Dimensions in mm
04-11-04
Fig 15. Package outline PDTA114EU (SOT323/SC-70)
10. Packing information
Table 9.
Packing methods
The indicated -xxx are the last three digits of the 12NC ordering code.[1]
Type number
Product data sheet
Description
Packing quantity
3000
10000
4 mm pitch, 8 mm tape and reel
-115
-135
PDTA114EE
SOT416
PDTA114EM
SOT883
2 mm pitch, 8 mm tape and reel
-
-315
PDTA114ET
SOT23
4 mm pitch, 8 mm tape and reel
-215
-235
PDTA114EU
SOT323
4 mm pitch, 8 mm tape and reel
-115
-135
[1]
PDTA114E_SER
Package
For further information and the availability of packing methods, see Section 14.
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
10 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
11. Soldering
2.2
1.7
solder lands
solder resist
1
0.85
2
solder paste
0.5
(3×)
occupied area
Dimensions in mm
0.6
(3×)
1.3
sot416_fr
Reflow soldering is the only recommended soldering method.
Fig 16. Reflow soldering footprint PDTA114EE (SOT416/SC-75)
1.3
0.7
R0.05 (12×)
solder lands
solder resist
0.9
0.6
0.7
solder paste
0.25
(2×)
occupied area
0.3
(2×)
0.3
0.4
(2×)
0.4
Dimensions in mm
sot883_fr
Reflow soldering is the only recommended soldering method.
Fig 17. Reflow soldering footprint PDTA114EM (SOT883/SC-101)
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
11 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
3.3
2.9
1.9
solder lands
solder resist
3
2
1.7
solder paste
occupied area
0.6
(3×)
0.7
(3×)
Dimensions in mm
0.5
(3×)
0.6
(3×)
1
sot023_fr
Fig 18. Reflow soldering footprint PDTA114ET (SOT23)
2.2
1.2
(2×)
1.4
(2×)
solder lands
4.6
solder resist
2.6
occupied area
Dimensions in mm
1.4
preferred transport direction during soldering
2.8
4.5
sot023_fw
Fig 19. Wave soldering footprint PDTA114ET (SOT23)
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
12 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
2.65
1.85
1.325
solder lands
solder resist
2
2.35
0.6
(3×)
3
solder paste
1.3
1
occupied area
0.5
(3×)
Dimensions in mm
0.55
(3×)
sot323_fr
Fig 20. Reflow soldering footprint PDTA114EU (SOT323/SC-70)
4.6
2.575
1.425
(3×)
solder lands
solder resist
occupied area
1.8
3.65 2.1
09
(2×)
Dimensions in mm
preferred transport
direction during soldering
sot323_fw
Fig 21. Wave soldering footprint PDTA114EU (SOT323/SC-70)
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
13 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
12. Revision history
Table 10.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
PDTA114E_SER v.10
20111221
Product data sheet
-
PDTA114E_SER v.9
Modifications:
•
Figure 2 and 5: corrected
PDTA114E_SER v.9
20111122
Product data sheet
-
PDTA114E_SERIES v.8
PDTA114E_SERIES v.8
20040802
Product specification
-
PDTA114E_SERIES v.7
PDTA114E_SERIES v.7
20030410
Product specification
-
-
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
14 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
13. Legal information
13.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
13.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
13.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
PDTA114E_SER
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
15 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
13.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
14. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
PDTA114E_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 21 December 2011
© NXP B.V. 2011. All rights reserved.
16 of 17
PDTA114E series
NXP Semiconductors
PNP resistor-equipped transistors; R1 = 10 k, R2 = 10 k
15. Contents
1
1.1
1.2
1.3
1.4
2
3
4
5
6
7
8
8.1
9
10
11
12
13
13.1
13.2
13.3
13.4
14
15
Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General description . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick reference data . . . . . . . . . . . . . . . . . . . . 1
Pinning information . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3
Thermal characteristics . . . . . . . . . . . . . . . . . . 4
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Test information . . . . . . . . . . . . . . . . . . . . . . . . . 9
Quality information . . . . . . . . . . . . . . . . . . . . . . 9
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 10
Packing information . . . . . . . . . . . . . . . . . . . . 10
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 14
Legal information. . . . . . . . . . . . . . . . . . . . . . . 15
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 15
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Contact information. . . . . . . . . . . . . . . . . . . . . 16
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 21 December 2011
Document identifier: PDTA114E_SER