SC18IS603

SC18IS602/602B/603 I2C-bus to SPI bridge Rev. 04 — 11 March 2008 Product data sheet 1. General description The SC18IS602/602B and SC18IS603 are designed to serve as an interface between a standard I2C-bus of a microcontroller and an SPI bus. This allows the microcontroller to communicate directly with SPI devices through its I2C-bus. The SC18IS602/602B/603 operates as an I2C-bus slave-transmitter or slave-receiver and an SPI master. The SC18IS602/602B/603 controls all the SPI bus-specific sequences, protocol, and timing. The SC18IS602/602B has its own internal oscillator, while the SC18IS603 requires an external clock source for operation. SC18IS602 and SC18IS603 do not support SS2 function as SPI slave select signal; this pin can only be used as GPIO2. 2. Features I I I I I I I I I I I2C-bus slave interface operating up to 400 kHz SPI master operating up to 1.8 Mbit/s (SC18IS602/602B) or 4 Mbit/s (SC18IS603) 200-byte data buffer Up to four slave select outputs Up to four programmable I/O pins Operating supply voltage: 2.4 V to 3.6 V Low power mode Internal oscillator option Active LOW interrupt output ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 I Latch-up testing is done to JEDEC Standard JESD78 that exceeds 100 mA I Very small 16-pin TSSOP 3. Applications I Converting I2C-bus to SPI I Adding additional SPI bus controllers to an existing system NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 4. Ordering information Table 1. Ordering information Package Name SC18IS602IPW SC18IS602BIPW SC18IS603IPW TSSOP16 TSSOP16 TSSOP16 Description plastic thin shrink small outline package; 16 leads; body width 4.4 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm Version SOT403-1 SOT403-1 SOT403-1 Type number 5. Block diagram SCL I2C-BUS SDA SPI BUFFER CONTROL REGISTER RESET INTERRUPT CONTROL LOGIC MOSI MISO SPICLK SS0 SS1 (1) SS2 SS3 SC18IS602 SC18IS602B INT INTERNAL OSCILLATOR 002aac443 (1) Unused slave select outputs may be used for GPIO. Fig 1. Block diagram of SC18IS602/602B SCL I2C-BUS SDA SPI BUFFER MOSI MISO SPICLK SS0 SS1 (1) SS2 CONTROL REGISTER RESET INTERRUPT CONTROL LOGIC SC18IS603 INT OSCILLATOR CLKIN 002aac444 (1) Unused slave select outputs may be used for GPIO; SC18IS603 does not have SS3. Fig 2. Block diagram of SC18IS603 SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 2 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 6. Pinning information 6.1 Pinning SS0/GPIO0 SS1/GPIO1 RESET VSS MISO MOSI SDA SCL 1 2 3 4 5 6 7 8 002aac441 16 A2 15 A1 14 A0 13 SS3/GPIO3 12 VDD 11 SPICLK 10 SS2/GPIO2 9 INT SS0/GPIO0 SS1/GPIO1 RESET VSS MISO MOSI SDA SCL 1 2 3 4 5 6 7 8 002aac442 16 A2 15 A1 14 A0 13 CLKIN 12 VDD 11 SPICLK 10 SS2/GPIO2 9 INT SC18IS602IPW SC18IS602BIPW SC18IS603IPW a. SC18IS602/602B Fig 3. Pin configuration for TSSOP16 b. SC18IS603 6.2 Pin description Table 2. Symbol Pin description Pin SC18IS602, SC18IS602B SS0/GPIO0 SS1/GPIO1 RESET VSS MISO MOSI SDA SCL INT SS2/GPIO2 SPICLK VDD SS3/GPIO3 CLKIN A0 A1 A2 [1] [2] Type SC18IS603 1 2 3 4 5 6 7 8 9 10[1] 11 12 13 14 15 16 I/O I/O I I O I/O I O I/O O I/O I I I I Description 1 2 3 4 5 6 7 8 9 10[1][2] 11 12 13 14 15 16 SPI slave select output 0 (active LOW) or GPIO 0 SPI slave select output 1 (active LOW) or GPIO 1 reset input (active LOW) ground supply Master In, Slave Out Master Out, Slave In I2C-bus data I2C-bus clock interrupt output (active LOW) SPI slave select output 2 (active LOW) or GPIO 2 SPI clock supply voltage SPI slave select output 3 (active LOW) or GPIO 3 external clock input address input 0 address input 1 address input 2 SC18IS602IPW and SC18IS603IPW do not support SS2. This pin should be used as GPIO2 only. SC18IS602BIPW does support SS2/GPIO2 function. This pin can be used as SS2 or GPIO2. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 3 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7. Functional description The SC18IS602/602B/603 acts as a bridge between an I2C-bus and an SPI interface. It allows an I2C-bus master device to communicate with any SPI-enabled device. 7.1 I2C-bus interface The I2C-bus uses two wires (SDA and SCL) to transfer information between devices connected to the bus, and it has the following features: • Bidirectional data transfer between masters and slaves • Multi-master bus (no central master) • Arbitration between simultaneously transmitting masters without corruption of serial data on the bus • Serial clock synchronization allows devices with different bit rates to communicate via one serial bus • Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial transfer • The I2C-bus may be used for test and diagnostic purposes A typical I2C-bus configuration is shown in Figure 4. (Refer to NXP Semiconductors’ UM10204, “I2C-bus specification and user manual”, document order number 9398 393 40011.) VDD RPU RPU I2C-bus I2C-BUS DEVICE I2C-BUS DEVICE SDA SCL SC18IS602/602B/603 002aac445 Fig 4. I2C-bus configuration The SC18IS602/602B/603 device provides a byte-oriented I2C-bus interface that supports data transfers up to 400 kHz. When the I2C-bus master is reading data from SC18IS60x, the device will be a slave-transmitter. The SC18IS60x will be a slave-receiver when the I2C-bus master is sending data. At no time does the SC18IS60x act as an I2C-bus master, however, it does have the ability to hold the SCL line LOW between bytes to complete its internal processes. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 4 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7.1.1 Addressing R/W slave address 0 1 0 1 A2 A1 A0 X fixed programmable 002aac446 Fig 5. Slave address The first seven bits of the first byte sent after a START condition defines the slave address of the device being accessed on the bus. The eighth bit determines the direction of the message. A ‘0’ in the least significant position of the first byte means that the master will write information to a selected slave. A ‘1’ in this position means that the master will read information from the slave. When an address is sent, each device in a system compares the first seven bits after the START condition with its address. If they match, the device considers itself addressed by the master as a slave-receiver or slave-transmitter, depending on the R/W bit. A slave address of the SC18IS602/602B/603 is comprised of a fixed and a programmable part. The programmable part of the slave address enables the maximum possible number of such devices to be connected to the I2C-bus. Since the SC18IS602/602B/603 have three programmable address bits (defined by the A2, A1, and A0 pins), it is possible to have eight of these devices on the same bus. The state of the A2, A1, and A0 pins are latched at reset. Changes made after reset will not alter the address. 7.1.2 Write to data buffer All communications to or from the SC18IS602/602B/603 occur through the data buffer. The data buffer is 200 bytes deep. A message begins with the SC18IS60x address, followed by the Function ID. Depending upon the Function ID, zero to 200 data bytes can follow. The SC18IS60x will place the data received into a buffer and continue loading the buffer until a STOP condition is received. After the STOP condition is detected, further communications will not be acknowledged until the function designated by the Function ID has been completed. S SLAVE ADDRESS W A FUNCTION ID A 0 TO 200 BYTES A P 002aac447 Fig 6. Write to data buffer 7.1.3 SPI read and write - Function ID 01h to 0Fh Data in the buffer will be sent to the SPI port if the Function ID is 01h to 0Fh. The Function ID contains the Slave Select (SS) to be used for the transmission on the SPI port. There are four Slave Selects that can be used, with each SS being selected by one of the bits in SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 5 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge the Function ID. There is no restriction on the number or combination of Slave Selects that can be enabled for an SPI message. If more than one SSn pin is enabled at one time, the user should be aware of possible contention on the data outputs of the SPI slave devices. Table 3. 7 0 [1] [2] Function ID 01h to 0Fh 6 0 5 0 4 0 3 SS3[1] 2 SS2[2] 1 SS1 0 SS0 SS3 does not exist in the SC18IS603. SS2 does not exist in the SC18IS602 and SC18IS603. Only SC18IS602B supports this function. The data on the SPI port will contain the same information as the I2C-bus data, but without the slave address and Function ID. For example, if the message shown in Figure 7 is transmitted on the I2C-bus, the SPI bus will send the message shown in Figure 8. write to buffer S SLAVE ADDRESS W A FUNCTION ID A DATA 1 A A DATA n A P 002aac448 Fig 7. I2C-bus message SPI data DATA 1 DATA n 002aac451 Fig 8. SPI message The SC18IS602/602B/603 counts the number of data bytes sent to the I2C-bus port and will automatically send this same number of bytes to the SPI bus. As the data is transmitted from the MOSI pin, it is also read from the MISO pin and saved in the data buffer. Therefore, the old data in the buffer is overwritten. The data in the buffer can then be read back. If the data from the SPI bus needs to be returned to the I2C-bus master, the process must be completed by reading the data buffer. Section 8 gives an example of an SPI read. 7.1.4 Read from buffer A read from the data buffer requires no Function ID. The slave address with the R/W bit set to a ‘1’ will cause the SC18IS602/602B/603 to send the buffer contents to the I2C-bus master. The buffer contents are not modified during the read process. S SLAVE ADDRESS R A DATA 1 A A DATA n NA P 002aac449 Fig 9. Read from buffer A typical write and read from an SPI EEPROM is shown in Section 8. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 6 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7.1.5 Configure SPI Interface - Function ID F0h The SPI hardware operating mode, data direction, and frequency can be changed by sending a ‘Configure SPI Interface’ command to the I2C-bus. S SLAVE ADDRESS W A F0h A DATA A P 002aac450 Fig 10. Configure SPI Interface After the SC18IS602/602B/603 address is transmitted on the bus, the Configure SPI Interface Function ID (F0h) is sent followed by a byte which will define the SPI communications. The Clock Phase bit (CPHA) allows the user to set the edges for sampling and changing data. The Clock Polarity bit (CPOL) allows the user to set the clock polarity. Figure 20 and Figure 21 show the different settings of Clock Phase bit CPHA. Table 4. Bit Symbol Reset Table 5. Bit 7:6 5 4 3:2 Configure SPI Interface (F0h) bit allocation 7 X X 6 X X 5 ORDER 0 4 X X 3 MODE1 0 2 MODE0 0 1 F1 0 0 F0 0 Configure SPI Interface (F0h) bit description Symbol ORDER Description reserved When logic 0, the MSB of the data word is transmitted first. If logic 1, the LSB of the data word is transmitted first. reserved 00 - SPICLK LOW when idle; data clocked in on leading edge (CPOL = 0, CPHA = 0) 01 - SPICLK LOW when idle; data clocked in on trailing edge (CPOL = 0, CPHA = 1) 10 - SPICLK HIGH when idle; data clocked in on trailing edge (CPOL = 1, CPHA = 0) 11 - SPICLK HIGH when idle; data clocked in on leading edge (CPOL = 1, CPHA = 1) MODE1:MODE0 Mode selection 1:0 F1:F0 SPI clock rate SC18IS602/602B: 00 - 1843 kHz 01 - 461 kHz 10 - 115 kHz 11 - 58 kHz SC18IS603: 00 - fosc⁄4 01 - fosc⁄16 10 - fosc⁄64 11 - fosc⁄128 SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 7 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7.1.6 Clear Interrupt - Function ID F1h An interrupt is generated by the SC18IS602/602B/603 after any SPI transmission has been completed. This interrupt can be cleared (INT pin HIGH) by sending a ‘Clear Interrupt’ command. It is not necessary to clear the interrupt; when polling the device, this function may be ignored. S SLAVE ADDRESS W A F1h A P 002aac452 Fig 11. Clear Interrupt 7.1.7 Idle mode - Function ID F2h A low-power mode may be entered by sending the ‘Idle Mode’ command. S SLAVE ADDRESS W A F2h A P 002aac453 Fig 12. Idle mode The Idle mode will be exited when its I2C-bus address is detected. 7.1.8 GPIO Write - Function ID F4h The state of the pins defined as GPIO may be changed using the Port Write function. S SLAVE ADDRESS W A F4h A DATA A P 002aac454 Fig 13. GPIO Write The data byte following the F4h command will determine the state of SS3, SS2, SS1, and SS0, if they are configured as GPIO. The Port Enable function will define if these pins are used as SPI Slave Selects or if they are GPIO. Table 6. Bit Symbol Reset [1] GPIO Write (F0h) bit allocation 7 X X 6 X X 5 X X 4 X X 3 SS3[1] 0 2 SS2 0 1 SS1 0 0 SS0 0 SS3 does not exist in the SC18IS603. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 8 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7.1.9 GPIO Read - Function ID F5h The state of the pins defined as GPIO may be read into the SC18IS602/602B/603 data buffer using the GPIO Read function. S SLAVE ADDRESS W A F5h A DATA A P 002aac455 Fig 14. GPIO Read Note that this function does not return the value of the GPIO. To receive the GPIO contents, a one-byte Read Buffer command would be required. The value of the Read Buffer command will return the following byte. Table 7. 7 X [1] GPIO Read (F5h) bit allocation 6 X 5 X 4 X 3 SS3[1] 2 SS2 1 SS1 0 SS0 SS3 does not exist in the SC18IS603. Data for pins not defined as GPIO are undefined. A GPIO Read is always performed to update the GPIO data in the buffer. The buffer is undefined after the GPIO data is read back from the buffer. Therefore, reading data from the GPIO always requires a two-message sequence (GPIO Read, followed by Read Buffer). 7.1.10 GPIO Enable - Function ID F6h At reset, the Slave Select pins (SS0, SS1, SS2 and SS3) are configured to be used as slave select outputs. If these pins are not required for the SPI functions, they can be used as GPIO after they are enabled as GPIO. Any combination of pins may be configured to function as GPIO or Slave Selects. After the GPIO Enable function is sent, the ports defined as GPIO will be configured as quasi-bidirectional. S SLAVE ADDRESS W A F6h A DATA A P 002aac456 Fig 15. GPIO Enable The data byte following the F6h command byte will determine which pins can be used as GPIO. A logic 1 will enable the pin as a GPIO, while a logic 0 will disable GPIO control. Table 8. 7 X [1] GPIO Enable (F6h) bit allocation 6 X 5 X 4 X 3 SS3[1] 2 SS2 1 SS1 0 SS0 SS3 does not exist in the SC18IS603. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 9 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7.1.11 GPIO Configuration - Function ID F7h The pins defined as GPIO may be configured by software to one of four types on a pin-by-pin basis. These are: quasi-bidirectional, push-pull, open-drain, and input-only. Two bits select the output type for each port pin. Table 9. 7 SS3.1[1] [1] GPIO Configuration (F7h) bit allocation 6 SS3.0[1] 5 SS2.1 4 SS2.0 3 SS1.1 2 SS1.0 1 SS0.1 0 SS0.0 SS3.1 and SS3.0 do not exist in the SC18IS603. Table 10. Bit 7 6 GPIO Configuration (F7h) bit description Symbol SS3.1[1] SS3.0[1] Description SS3[1:0] = 00: quasi-bidirectional SS3[1:0] = 01: push-pull SS3[1:0] = 10: input-only (high-impedance) SS3[1:0] = 11: open-drain 5 4 SS2.1 SS2.0 SS2[1:0] = 00: quasi-bidirectional SS2[1:0] = 01: push-pull SS2[1:0] = 10: input-only (high-impedance) SS2[1:0] = 11: open-drain 3 2 SS1.1 SS1.0 SS1[1:0] = 00: quasi-bidirectional SS1[1:0] = 01: push-pull SS1[1:0] = 10: input-only (high-impedance) SS1[1:0] = 11: open-drain 1 0 SS0.1 SS0.0 SS0[1:0] = 00: quasi-bidirectional SS0[1:0] = 01: push-pull SS0[1:0] = 10: input-only (high-impedance) SS0[1:0] = 11: open-drain [1] SS3.1 and SS3.0 do not exist in the SC18IS603. The SSn pins defined as GPIO, for example SS0.0 and SS0.1, may be configured by software to one of four types. These are: quasi-bidirectional, push-pull, open-drain, and input-only. Two configuration bits in GPIO Configuration register for each pin select the type for each pin. A pin has Schmitt-triggered input that also has a glitch suppression circuit. For SC18IS603, the SS3 pin defined as GPIO is non-existent. 7.1.11.1 Quasi-bidirectional output configuration Quasi-bidirectional outputs can be used both as an input and output without the need to reconfigure the pin. This is possible because when the pin outputs a logic HIGH, it is weakly driven, allowing an external device to pull the pin LOW. When the pin is driven LOW, it is driven strongly and able to sink a large current. There are three pull-up transistors in the quasi-bidirectional output that serve different purposes. One of these pull-ups, called the ‘very weak’ pull-up, is turned on whenever the port latch for the pin contains a logic 1. This very weak pull-up sources a very small current that will pull the pin HIGH if it is left floating. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 10 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge A second pull-up, called the ‘weak’ pull-up, is turned on when the port latch for the pin contains a logic 1 and the pin itself is also at a logic 1 level. This pull-up provides the primary source current for a quasi-bidirectional pin that is outputting a 1. If this pin is pulled LOW by an external device, the weak pull-up turns off, and only the very weak pull-up remains on. In order to pull the pin LOW under these conditions, the external device has to sink enough current to overpower the weak pull-up and pull the pin below its input threshold voltage. The third pull-up is referred to as the ‘strong’ pull-up. This pull-up is used to speed up LOW-to-HIGH transitions on a quasi-bidirectional pin when the port latch changes from a logic 0 to a logic 1. When this occurs, the strong pull-up turns on for two CPU clocks quickly pulling the pin HIGH. The quasi-bidirectional pin configuration is shown in Figure 16. Although the SC18IS602/602B/603 is a 3 V device, most of the pins are 5 V tolerant. If 5 V is applied to a pin configured in quasi-bidirectional mode, there will be a current flowing from the pin to VDD causing extra power consumption. Therefore, applying 5 V to pins configured in quasi-bidirectional mode is discouraged. A quasi-bidirectional pin has a Schmitt-triggered input that also has a glitch suppression circuit. 2 SYSTEM CLOCK CYCLES VDD P strong P very weak P weak GPIO pin pin latch data VSS input data glitch rejection 002aac548 Fig 16. Quasi-bidirectional output configuration 7.1.11.2 Open-drain output configuration The open-drain output configuration turns off all pull-ups and only drives the pull-down transistor of the pin when the port latch contains a logic 0. To be used as a logic output, a pin configured in this manner must have an external pull-up, typically a resistor tied to VDD. The pull-down for this mode is the same as for the quasi-bidirectional mode. The open-drain pin configuration is shown in Figure 17. An open-drain pin has a Schmitt-triggered input that also has a glitch suppression circuit. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 11 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge GPIO pin pin latch data VSS input data glitch rejection 002aab883 Fig 17. Open-drain output configuration 7.1.11.3 Input-only configuration The input-only pin configuration is shown in Figure 18. It is a Schmitt-triggered input that also has a glitch suppression circuit. input data glitch rejection GPIO pin 002aab884 Fig 18. Input-only configuration 7.1.11.4 Push-pull output configuration The push-pull output configuration has the same pull-down structure as both the open-drain and the quasi-bidirectional output modes but provides a continuous strong pull-up when the port latch contains a logic 1. The push-pull mode may be used when more source current is needed from a pin output. The push-pull pin configuration is shown in Figure 19. A push-pull pin has a Schmitt-triggered input that also has a glitch suppression circuit. VDD P strong GPIO pin N pin latch data VSS input data glitch rejection 002aab885 Fig 19. Push-pull output configuration SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 12 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 7.2 External clock input (SC18IS603) In this device, the processor clock is derived from an external source driving the CLKIN pin. The rate may be from 0 Hz up to 18 MHz. Using the external clock allows higher frequencies from the SPI interface, thus the SPI Master operating can be up to 4 Mbit/s. The CLKIN frequency does not affect the clock speed of the I2C-bus interface, however, it will have an effect on the low period between bytes on the I2C-bus. 7.3 SPI interface The SPI interface can support Mode 0 through Mode 3 of the SPI specification and can operate up to 1.8 Mbit/s (SC18IS602/602B) or 4.0 Mbit/s (SC18IS603). The SPI interface uses at least four pins: SPICLK, MOSI, MISO, and Slave Select (SSn). SSn are the slave select pins. In a typical configuration, an SPI master selects one SPI device as the current slave. There are actually four SSn pins (SS0, SS1, SS2 and SS3) to allow the SC18IS602/602B/603 to communicate with multiple SPI devices. The SC18IS602/602B/603 generates the SPICLK (SPI clock) signal in order to send and receive data. The SCLK, MOSI, and MISO are typically tied together between two or more SPI devices. Data flows from the SC18IS602/602B/603 (master) to slave on the MOSI pin (Pin 6) and the data flows from slave to SC18IS602/602B/603 (master) on the MISO pin (Pin 5). SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 13 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 8. I2C-bus to SPI communications example The following example describes a typical sequence of events required to read the contents of an SPI-based EEPROM. This example assumes that the SC18IS602/602B/603 is configured to respond to address 50h. A START condition is shown as ‘ST’, while a STOP condition is ‘SP’. The data is presented in hexadecimal format. 1. The first message is used to configure the SPI port for mode and frequency. ST,50,F0,02,SP SPI frequency 115 kHz using Mode 0 2. An SPI EEPROM first requires that a Write Enable command be sent before data can be written. ST,50,04,06,SP 06h EEPROM write enable using SS2, assuming the Write Enable is 3. Clear the interrupt. This is not required if using a polling method rather than interrupts. ST,50,F1,SP Clear interrupt 4. Write the 8 data bytes. The first byte (Function ID) tells the SC18IS602/602B/603 which Slave Select output to use. This example uses SS2 (shown as 04h). The first byte sent to the EEPROM is normally 02h for the EEPROM write command. The next one or two bytes represent the subaddress in the EEPROM. In this example, a two-byte subaddress is used. Bytes 00 and 30 would cause the EEPROM to write to subaddress 0030h. The next eight bytes are the eight data bytes that will be written to subaddresses 0030h through 0037h. ST,50,04,02,00,30,01,02,03,04,05,06,07,08,SP Write 8 bytes using SS2 5. When an interrupt occurs, do a Clear Interrupt or wait until the SC18IS602/602B/603 responds to its I2C-bus address. ST,50,F1,SP Clear interrupt 6. Read the 8 bytes from the EEPROM. Note that we are writing a command, even though we are going to perform a read from the SPI port. The Function ID is again 04h, indicating that we are going to use SS2. The EEPROM requires that you send a 03h for a read, followed by the subaddress you would like to read. We are going to read back the same data previously written, so this means that the subaddress should be 0030h. We would like to read back 8 bytes so we can send eight bytes of FFh to tell the SC18IS602/602B/603 to send eight more bytes on MOSI. While it is sending these eight data bytes, it is also reading the MISO pin and saving the data in the buffer. ST,50,04,03,00,30,FF,FF,FF,FF,FF,FF,FF,FF,SP 7. The interrupt can be cleared, if needed. ST,50,F1,SP Clear interrupt 8. Read back the data buffer. Note that we will actually need to read back 11 data bytes since the first three bytes sent on the SPI port were the read code (03h) and the two subaddress bytes. ST,50,00,00,00,01,02,03,04,05,06,07,08,SP Read the data buffer Read 8 bytes using SS2 SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 14 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge You can see that on the I2C-bus the first four bytes do not contain the data from the SPI bus. The first byte is the SC18IS60x address, followed by three dummy data bytes. These dummy data bytes correspond to the three bytes sent to the EEPROM before it actually places data on the bus (command 03h, subaddress 0030h). 9. Limiting values Table 11. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).[1][2] Symbol Tamb(bias) Tstg Vn IOH(I/O) IOL(I/O) II/O(tot)(max) Ptot/pack [1] [2] [3] Parameter bias ambient temperature storage temperature voltage on any other pin HIGH-level output current per input/output pin LOW-level output current per input/output pin maximum total I/O current total power dissipation per package Conditions operating referenced to VSS Min −55 −65 −0.5 [3] Max +125 +150 +5.5 8 20 120 1.5 Unit °C °C V mA mA mA W - This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum. Parameters are valid over the operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. Based on package heat transfer, not device power consumption. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 15 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 10. Static characteristics Table 12. Static characteristics VDD = 2.4 V to 3.6 V; Tamb = −40 °C to +85 °C (industrial); unless otherwise specified. Symbol IDD(oper) Parameter operating supply current Conditions VDD = 3.6 V f = 7.3728 MHz f = 12 MHz f = 18 MHz IDD(idle) Idle mode supply current VDD = 3.6 V f = 7.3728 MHz f = 12 MHz f = 18 MHz Vth(HL) Vth(LH) Vhys VOL HIGH-LOW threshold voltage LOW-HIGH threshold voltage hysteresis voltage LOW-level output voltage all pins IOL = 20 mA IOL = 10 mA IOL = 3.2 mA VOH HIGH-level output voltage all pins IOH = −8 mA; push-pull mode IOH = −3.2 mA; push-pull mode IOH = −20 µA; quasi-bidirectional mode Cig IIL ILI ITHL RRESET_N(int) input capacitance at gate LOW-level input current input leakage current HIGH-LOW transition current internal pull-up resistance on pin RESET logical 0; VI = 0.4 V all ports; VI = VIL or VIH all ports; logical 1-to-0; VI = 2.0 V at VDD = 3.6 V [2] [3] [4] [5][6] Min 0.22VDD VDD − 1 VDD − 0.7 VDD − 0.3 −30 10 Typ[1] 5.6 7 11 3.3 3.6 4 0.4VDD 0.6VDD 0.2VDD 0.6 0.3 0.2 VDD − 0.4 VDD − 0.2 - Max 6.7 13 16 3.9 4.8 6 0.7VDD 1.0 0.5 0.3 15 −80 ±10 −450 30 Unit mA mA mA mA mA mA V V V V V V V V V pF µA µA µA kΩ Schmitt trigger input Schmitt trigger input [1] [2] [3] [4] [5] [6] Typical ratings are not guaranteed. The values listed are at room temperature, 3 V. Pin capacitance is characterized but not tested. Measured with pins in quasi-bidirectional mode. Measured with pins in high-impedance mode. Pins in quasi-bidirectional mode with weak pull-up (applies to all pins with pull-ups). Pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is highest when VI is approximately 2 V. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 16 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 11. Dynamic characteristics Table 13. Dynamic characteristics VDD = 2.4 V to 3.6 V; Tamb = −40 °C to +85 °C (industrial); unless otherwise specified. Symbol fosc(RC) Parameter internal RC oscillator frequency Conditions nominal f = 7.3728 MHz; trimmed to ±1 % at Tamb = 25 °C [1] Variable clock Min 7.189 Max 7.557 fosc = 12 MHz Min Max - Unit MHz External clock input fosc TCLCL tCHCX tCLCX tCLCH tCHCL tgr tsa oscillator frequency clock cycle time clock HIGH time clock LOW time clock rise time clock fall time glitch rejection time signal acceptance time RESET pin any pin except RESET RESET pin any pin except RESET SPI master interface fSPI TSPICYC tSPICLKH tSPICLKL tSPIDSU tSPIDH tSPIDV tSPIOH tSPIR SPI operating frequency SPI cycle time SPICLK HIGH time SPICLK LOW time SPI data set-up time SPI data hold time SPI enable to output data 3.0 MHz valid time 4.5 MHz SPI output data hold time SPI rise time SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SSn) tSPIF SPI fall time SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SSn) [1] 0 55 22 22 125 50 4⁄ fosc 2⁄ fosc 2⁄ fosc 18 TCLCL − tCLCX TCLCL − tCHCX 5 5 50 15 fosc⁄ 4 22 22 125 50 222 111 111 100 100 0 - 5 5 50 15 4.5 160 111 100 2000 100 2000 MHz ns ns ns ns ns ns ns ns ns MHz ns ns ns ns ns ns ns ns ns ns ns ns Glitch filter 4.5 MHz 4.5 MHz 160 111 100 2000 100 2000 100 100 0 0 0 - Parameters are valid over operating temperature range unless otherwise specified. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 17 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge TCLCL tSPIF SPICLK (CPOL = 0) (output) tSPIF tSPICLKL SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIF MOSI (output) master MSB/LSB out master LSB/MSB out 002aac457 tSPIR tSPICLKL tSPICLKH tSPIR tSPICLKH tSPIDH LSB/MSB in tSPIOH tSPIDV tSPIR MSB/LSB in tSPIDV Fig 20. SPI master timing (CPHA = 0) TCLCL tSPIF SPICLK (CPOL = 0) (output) tSPICLKL tSPIR tSPICLKH tSPIF tSPICLKH SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIF MOSI (output) master MSB/LSB out tSPIDH tSPICLKL tSPIR MSB/LSB in tSPIDV tSPIOH LSB/MSB in tSPIDV tSPIDV tSPIR master LSB/MSB out 002aac458 Fig 21. SPI master timing (CPHA = 1) VDD − 0.5 V 0.45 V 0.2VDD + 0.9 V 0.2VDD − 0.1 V tCHCX tCHCL tCLCX TCLCL tCLCH 002aab886 Fig 22. External clock timing SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 18 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 12. Package outline TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index A1 θ Lp L (A 3) A 1 e bp 8 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.40 0.06 θ 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 23. Package outline SOT403-1 (TSSOP16) SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 19 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 13. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 13.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 13.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 13.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 20 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 13.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 24) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 14 and 15 Table 14. SnPb eutectic process (from J-STD-020C) Package reflow temperature (°C) Volume (mm3) < 350 < 2.5 ≥ 2.5 Table 15. 235 220 Lead-free process (from J-STD-020C) Package reflow temperature (°C) Volume (mm3) < 350 < 1.6 1.6 to 2.5 > 2.5 260 260 250 350 to 2000 260 250 245 > 2000 260 245 245 ≥ 350 220 220 Package thickness (mm) Package thickness (mm) Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 24. SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 21 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 24. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 14. Abbreviations Table 16. Acronym CDM CPU EEPROM ESD GPIO HBM I/O I2C-bus LSB MM MSB SPI Abbreviations Description Charged Device Model Central Processing Unit Electrically Erasable Programmable Read-Only Memory ElectroStatic Discharge General Purpose Input/Output Human Body Model Input/Output Inter-Integrated Circuit bus Least Significant Bit Machine Model Most Significant Bit Serial Peripheral Interface SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 22 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 15. Revision history Table 17. Revision history Release date Data sheet status Product data sheet Change notice Supersedes SC18IS602_603_3 Document ID Modifications: SC18IS602_602B_603_4 20080311 • • • added Type number SC18IS602BIPW Section 1 “General description”, 2nd paragraph: added second sentence. Section 6 “Pinning information”: – added “SC18IS602BIPW” to Figure 3a – Table 2 “Pin description”: added Table note [1] and Table note [2] and their references at pin 10 • • SC18IS602_603_3 SC18IS602_603_2 SC18IS602_603_1 Table 3 “Function ID 01h to 0Fh”: added Table note [2] and its reference at bit 2, SS2 Section 7.1 “I2C-bus interface”, 2nd paragraph: updated title of referenced document Product data sheet Product data sheet Product data sheet SC18IS602_603_2 SC18IS602_603_1 - 20070813 20061213 20060926 SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 23 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 16. Legal information 16.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term ‘short data sheet’ is explained in section “Definitions”. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 16.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com SC18IS602_602B_603_4 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 04 — 11 March 2008 24 of 25 NXP Semiconductors SC18IS602/602B/603 I2C-bus to SPI bridge 18. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 Functional description . . . . . . . . . . . . . . . . . . . 4 7.1 I2C-bus interface . . . . . . . . . . . . . . . . . . . . . . . . 4 7.1.1 Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 7.1.2 Write to data buffer . . . . . . . . . . . . . . . . . . . . . . 5 7.1.3 SPI read and write - Function ID 01h to 0Fh . . 5 7.1.4 Read from buffer . . . . . . . . . . . . . . . . . . . . . . . . 6 7.1.5 Configure SPI Interface - Function ID F0h . . . . 7 7.1.6 Clear Interrupt - Function ID F1h . . . . . . . . . . . 8 7.1.7 Idle mode - Function ID F2h . . . . . . . . . . . . . . . 8 7.1.8 GPIO Write - Function ID F4h . . . . . . . . . . . . . 8 7.1.9 GPIO Read - Function ID F5h . . . . . . . . . . . . . 9 7.1.10 GPIO Enable - Function ID F6h . . . . . . . . . . . . 9 7.1.11 GPIO Configuration - Function ID F7h . . . . . . 10 7.1.11.1 Quasi-bidirectional output configuration . . . . . 10 7.1.11.2 Open-drain output configuration . . . . . . . . . . . 11 7.1.11.3 Input-only configuration . . . . . . . . . . . . . . . . . 12 7.1.11.4 Push-pull output configuration . . . . . . . . . . . . 12 7.2 External clock input (SC18IS603). . . . . . . . . . 13 7.3 SPI interface . . . . . . . . . . . . . . . . . . . . . . . . . . 13 8 I2C-bus to SPI communications example . . . 14 9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 15 10 Static characteristics. . . . . . . . . . . . . . . . . . . . 16 11 Dynamic characteristics . . . . . . . . . . . . . . . . . 17 12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19 13 Soldering of SMD packages . . . . . . . . . . . . . . 20 13.1 Introduction to soldering . . . . . . . . . . . . . . . . . 20 13.2 Wave and reflow soldering . . . . . . . . . . . . . . . 20 13.3 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 20 13.4 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 21 14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 22 15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 23 16 Legal information. . . . . . . . . . . . . . . . . . . . . . . 24 16.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 24 16.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 16.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 16.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 17 Contact information. . . . . . . . . . . . . . . . . . . . . 24 18 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 11 March 2008 Document identifier: SC18IS602_602B_603_4