H2C-R-AC120-B

Motor Timer H2C 1/16 DIN Size Motor Timer Offers Five Selectable Time Ranges ■ Each unit provides five field-selectable time ranges using the front panel time range selector ■ ON-delay or Signal OFF-delay from clutch input are available ■ Neon timing indicator and moving pointer show status ■ Panel mounting adapters, sockets, protective cover and other accessories may be ordered separately Ordering Information ■ TIMERS Note: The complete part numbers shown here are the only H2C timers currently available. Some time ranges and supply voltages have been discontinued. Timing function Contact type Time limit Instantaneous Motor and clutch connection Terminal form Time range codes Part number ON-delay ON-delay Signal OFF-delay SPDT SPDT SPDT SPDT SPDT – Parallel Independent Independent 8-pin round socket Front terminal screws 8-pin round socket A = 1.25 sec to 30 hr, B = 0.2 sec to 6 hr, C = 0.5 sec to 12 hr H2C-8-AC24-B H2C-F-AC24-B H2C-8R-AC24-A H2C-8-AC120-A H2C-F-AC12-C H2C-8R-AC120-A H2C-8-AC120-B H2C-8R-AC120-B H2C-8-AC120-C H2C-8R-AC120-C H2C-8-AC240-A H2C-8R-AC240-A H2C-8-AC240-B H2C-8R-AC240-B H2C-8-AC240-C H2C-8R-AC240-C ■ ACCESSORIES Description Sockets 8-pin (For H2C-8 and H2C-8R) Hold-down clips Panel mounting adapters Time setting ring Protective cover NEMA 4 cover Mounting track End plate Spacer Bottom surface or track mounting, top screw terminals; order hold down clips separately Bottom surface or track mounting, top screw terminals Bottom surface or track mounting, top screw terminals, finger safe terminal conforms to VDE0106/P100 Back mounting, for use with Y92F-30 mounting adapter, bottom screw terminals Terminal cover for P3G sockets, conforms to VDE0106/P100 One pair; for surface mounting using PF085A socket Fits behind panel, ideal for side-by-side installation. Use P3G-08 socket Flush mounting adapter (88 mm x 58 mm x 63.7 mm) Flush mounting adapter (58 mm x 50 mm x 63.7 mm) Use one or two to lock in settings Hard plastic cover protects against dust, dirt and water; not for use with panel adapters Y92F-70 and Y92F-71 Waterproof front cover DIN rail, 50 cm (1.64 ft) length; 7.3 mm thick DIN rail, 1 m (3.28 ft) length; 7.3 mm thick DIN rail, 1m (3.28 ft) length; 16 mm thick Part number PF085A P2CF-08 P2CF-08-E P3G-08 Y92A-48G Y92H-2 Y92F-30 Y92F-70 Y92F-71 Y92A-Y1 Y92A-48B Y92A-48N PFP-50N PFP-100N PFP-100N2 PFP-M PFP-S H2C Time range code A B C H2C Range selector position Display Time range Display Time range Display Timer range 30 s 1.25 to 30 sec 6s 0.2 to 6 sec 12 s 0.5 to 12 sec 3m 7.5 sec to 3 min 60 s 2 to 60 sec 120 s 5 to 120 sec 30 m 1.25 to 30 min 6m 0.2 to 6 min 12 m 0.5 to 12 min 3h 7.5 min to 3 hr 60 m 2 to 60 min 120 m 5 to 120 min 30 h 1.25 to 30 hr 6h 0.2 to 60 hr 12 h 0.5 to 12 hr Specifications Part number Supply voltage Operating voltage AC Power consumption Motor and clutch connection Timing functions Inputs Control output Type Time limit Instantaneous Max. load Min. load Repeat accuracy Setting error Resetting system Resetting time Indicators Materials Mounting Connections Weight Approvals UL CSA Others Operating ambient temperature Humidity Vibration Mechanical durability Malfunction durability Shock Mechanical durability Malfunction durability Variation due to voltage change Variation due to temperature change Insulation resistance Dielectric strength Service life Mechanical Electrical H2C-8 H2C-F H2C-8R 24 V, 120 V or 240 V; 50/60 Hz 85% to 110% of rated voltage 90% to 110% of rated voltage if voltage continues to be applied after set time elapses 3.5 VA Parallel Independent Independent ON-delay ON-delay Signal OFF-delay (clutch) – – Voltage clutch signal SPDT SPDT SPDT SPDT SPDT – 6 A, 250 VAC (p.f. = 1) 100 mA, 5 VDC ±0.5% max.; ±1% max. for 0.2 to 6 second range and 0.5 to 12 second range ±2% max. Self resetting Electric resetting 0.5 sec max. Timing (red), moving pointer Plastic case, knob Panel, surface, track Surface or track Panel, surface track 8-pin round socket Front terminal screws 8-pin round socket 180 g (6.3 oz) 270 g (9.5 oz) 180 g (6.3 oz) Recognized, File No. E52800 Certified, File No. LR22310 SEV, File No. 1021 -10° to 50°C (14° to 122°F) 45% to 85% RH 10 to 55 Hz, 0.75 mm (0.03 in) double amplitude 10 to 55 Hz, 0.5 mm (0.02 in) double amplitude 100G 15 G ±1% max. ±1% max. 100 MΩ min. at 500 VDC 2,500 VAC, 50/60 Hz for 1 minute between current-carrying and non-current carrying parts 2,000 VAC, 50/60 Hz for 1 minute between contact and control circuit and between contacts of different poles 30 million operations minimum 200,000 operations at 6 A, 250 VAC (p.f. = 1) 2 H2C H2C Engineering Data ■ ELECTRICAL SERVICE LIFE Timing Charts In the schematic diagrams, each thick line indicates the external wiring. ■ H2C-8 ON-DELAY TIMER ■ H2C-8R SIGNAL OFF-DELAY TIMER ■ H2C-F ON-DELAY TIMER 3 H2C H2C Dimensions Unit: mm (inch) ■ TIMERS H2C-8 and H2C-8R H2C-F ■ ACCESSORIES PF085A Bottom Surface or Track Mounting Socket P2CF-08 Track Mounting/Front Connecting Socket Eight M3.5 x 7.5 sems 7.8 (0.31) 3 (0.12) 4.5 (0.18) Terminal Arrangement/ Internal Connections (Top View) Surface Mounting Holes Two, 4.5 dia. or two M4 socket mounting holes 70 max. (2.76) 4 (0.16) 35.4 (1.39) Two 4.5 dia. holes 50 max. (1.97) 40 ± 0.2 (1.57) 20.3 max. (0.80) 4 H2C H2C P2CF-08E Finger Safe Terminal Type Conforming to VDE0106/P100 Eight M3.5 x 7.5 sems 4.5 (0.18) 5 7.8 (0.31) 3 1.3 70 max. (2.76) 35.4 (1.39) Two 4.5 dia. holes 40±0.2 19 50 max. (1.97) 20.3 21.5 max P3G-08 Back Connecting Socket 27 dia. (1.06) Terminal Arrangement 45 (1.77) 45 (1.77) 4.9 (0.19) 17 (0.67) Y92A-48G Finger Safe Terminal for P3G-08 Conforming to VDE0106/P100 Twelve, 6.4 dia. holes 47.7 x 4.47 34 48 x 48 16.5 27.6 47.4 Y92F-30 Mounting Adapter (For H2C-8 and H2C-8R) Adapter installs behind the panel. It is ideal for side by side installation. Use P3GA-08 socket. 5 H2C H2C Unit: mm (inch) Y92F-70 Mounting Adapter Charcoal gray panel adapter installs through panel front. Timer face fits bezel, rear of timer clips to adapter. Use P3G-08. Y92F-71 Mounting Adapter Charcoal gray panel adapter installs through panel front. Timer face fits bezel, rear of timer clips to adapter. Use P3G-08. Y92A-Y1 Time Setting Ring The time setting ring allows the operator to lock in a selected, preset time. A recess in the ring engages a notch in the lock ring tab, stopping movement of the dial. The time setting ring minimizes setting error by repeatedly stopping at the same point on the dial. For machines that are regularly set for two time settings, two Y92A-Y1 Time Setting Rings may be installed for two setpoints. Position to lock in the time setting knob. The set position of the time setting knob is fixed. The time setting ring is secured to the time setting knob. Y92A-48B Protective Cover The protective cover protects the front panel, particularly the time setting section, against dust, dirt and water. It also prevents the set value from being altered due to accidental contact with the time setting knob. Note: 1. The Y92A-48B Protective Cover is made of a hard plastic and therefore must be removed to change the timer set value. 2. The Protective Cover cannot be mounted if the Panel Cover (sold separately) is used on the Timer. 3. When using a front cover for flush mounting, use the Y92F-30 Adapter. The Y92F-73 or Y92F-74 Flush Mounting Adapter cannot be used. 6 H2C H2C Y92H-1 Hold Down Clips Use these clips with H2C-8 and H2C-8R timers mounted in a PF085A socket. The pair of clips secure the timer to the socket in installations with significant vibration. PFP-100N, PFP-50N Mounting Track PFP-100N2 Mounting Track 16 (0.63) 7.3±0.15 4.5 (0.18) 4.5 (0.18) 35±0.3 15 25 25 10 15 25 25 10 L 35±0.3 27 27±0.15 25 25 10 1 (0.04) 25 L 25 29.2 (1.15) 24 1.5 (0.06) 1 (0.04) 15 10 L: Length 1m PFP-100N 50 cm PFP-50N 1m PFP-100N2 PFP-M End Plate PFP-S Spacer 10 (0.39) 6.2 (0.24) 1.8 (0.07) 1 50 (1.97) 1.8 11.5 (0.45) M4 x 8 pan head 10 screw (10.39) 16 (0.63) 5 (0.20) 35.5 35.3 (1.39) 12 34.8 (1.37) 44 (1.74) 1.3 (0.05) 4.8 (0.19) 16.5 (0.65) Connections Part number Input (clutch) terminal numbers Power supply terminal numbers Output terminal number AC common AC hot AC common AC hot Type COM NC NO H2C-8 – – 2 7 Time limit 8 5 6 Instantaneous 1 4 3 H2C-8R 1 4 2 7 Time limit 8 5 6 H2C-F B2 B1 A2 A1 Time limit 15 16 18 Instantaneous 21 22 24 7 H2C H2C Installation ■ SELECTING POWER FREQUENCY H2C motor timers are designed to operate accurately on either 50 Hz or 60 Hz. A selector switch is located on the rear of the case in the lower left-hand corner. Set the proper frequency for your installation before mounting the timer. If the power frequency does not match the setting, the time measurement will be inaccurate. Operation ■ SELECTING TIME RANGES The time range selector is a rotary switch located on the top right corner of the front panel. Use a screwdriver or Allen wrench to turn the switch. First, turn power OFF to the timer. The five time range choices are 60 degrees apart. Above the switch is a small window that shows the range selection. WARNING Do not change the time range while the timer is operating. This will cause the timer to malfunction. Mounting ■ PANEL MOUNTING Using Y92F-30 Adapter Insert the timer through the panel cutout. Push the Y92F-30 adapter from the rear of the timer as far forward toward the panel as possible. Wire the P3G-08 socket, then push it onto the rear of the timer. The tighten the two retaining screws. To release the adapter, lift the tab at the rear of the adapter. 8 H2C H2C Several timers may be panel mounted close together using the Y92F-30 adapter as shown here. When mounting two or more timers in a vertical line, arrange the adaptors so that their molded tabs are positioned on the right and left sides. When mounting two or more timers in a horizontal line, arrange the adapters so that their molded tabs are positioned on the top and bottom sides. Using Y92F-70 and Y92F-71 Adapters Install the H2C-8 and H2C-8R timer, face first, into the back side of the Y92F-70 or Y92F-71 adapter so the bezel fits snugly. Be sure the retaining clips at the back of the adapter fit into the slots on either side of the timer. Compress the top and bottom tabs of the adapter then push the adapter through the front side of the panel cutout. Be sure the tabs extend after installation for a secure fit. To remove the timer from the adapter, unclip the two retaining clips at the back of the adapter. To remove the adapter and timer from the panel as a unit, compress the tabs behind the panel and push the unit out the front of the panel. ■ TRACK MOUNTING H2C-F with Built-in Track Adapter Mounting First, hook portion "A" on the rear of the timer onto and edge of the track. Then, press the timer in direction "B" until the latch on the bottom rear of the timer latches securely. Removal Pull the latch "C" with a flat blade screwdriver and remove the timer from the mounting track. 9 H2C H2C P2CF-08 Socket (For H2C-8 and H2C-BR) Mounting The P2CF-08 socket has two hooks that secure the timer to the socket. Be sure to allow at least 20 mm (0.79 in) clearance above and below the socket to gain access and to release the hooks for servicing and maintenance. Insert timer into the socket. Latch hooks. Then clip the rear of the socket to the track. Push the bottom onto the track until the latch hooks securely. Removal Pull the latch on the socket with a flat-blade screwdriver and remove the timer and socket as one unit. ■ TRACK MOUNTING NOTE: DIMENSIONS ARE SHOWN IN MILLIMETERS. To convert millimeters to inches divide by 25.4. OMRON ELECTRONICS LLC OMRON ON-LINE OMRON CANADA, INC. One East Commerce Drive Schaumburg, IL 60173 Global - http://www.omron.com USA - http://www.omron.com/oei Canada - http://www.omron.com/oci 885 Milner Avenue Scarborough, Ontario M1B 5V8 1-800-55-OMRON Cat. No. GC TMCN1 2/02 Specifications subject to change without notice. 10 416-286-6465 Printed in the U.S.A.