CAT5411YI-00-T2

ON Semiconductor Is Now To learn more about onsemi™, please visit our website at www.onsemi.com onsemi and       and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as-is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. Other names and brands may be claimed as the property of others. CAT5411 Dual Digital Potentiometer (POT) with 64 Taps and SPI Interface http://onsemi.com Description The CAT5411 is two digital potentiometers (POTs) integrated with control logic and 16 bytes of NVRAM memory. Each digital POT consists of a series of 63 resistive elements connected between two externally accessible end points. The tap points between each resistive element are connected to the wiper outputs with CMOS switches. A separate 6-bit control register (WCR) independently controls the wiper tap switches for each digital POT. Associated with each wiper control register are four 6-bit non-volatile memory data registers (DR) used for storing up to four wiper settings. Writing to the wiper control register or any of the non-volatile data registers is via a SPI serial bus. On power-up, the contents of the first data register (DR0) for each of the two potentiometers is automatically loaded into its respective wiper control register. The CAT5411 can be used as a potentiometer or as a two terminal, variable resistor. It is intended for circuit level or system level adjustments in a wide variety of applications.         Two Linear-taper Digital Potentiometers 64 Resistor Taps per Potentiometer End to End Resistance 2.5 kW, 10 kW, 50 kW or 100 kW Potentiometer Control and Memory Access via SPI Interface: Mode (0, 0) and (1, 1) Low Wiper Resistance, Typically 80 W Nonvolatile Memory Storage for up to Four Wiper Settings for Each Potentiometer Automatic Recall of Saved Wiper Settings at Power Up 2.5 to 6.0 Volt Operation Standby Current less than 1 mA 24-lead SOIC and 24-lead TSSOP Industrial Temperature Ranges These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant SOIC−24 W SUFFIX CASE 751BK PIN CONNECTIONS VCC NC 1 RL0 NC RH0 NC RW0 NC CS A0 WP Features     TSSOP24 Y SUFFIX CASE 948AR SI CAT5411 SO HOLD SCK A1 RL1 NC RH1 NC RW1 NC GND NC SOIC−24 (W) (Top View) SI A1 RL1 RH1 RW1 GND NC NC NC NC SCK HOLD 1 CAT5411 WP CS RW0 RH0 RL0 VCC NC NC NC NC A0 SO TSSOP24 (Y) (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet.  Semiconductor Components Industries, LLC, 2013 July, 2013 − Rev. 13 1 Publication Order Number: CAT5411/D CAT5411 MARKING DIAGRAMS (SOIC−24) (TSSOP−24) L3B CAT5411WT −RRYMXXXX RLB CAT5411YT 3YMXXX R = Resistance 1 = 2.5 KW 2 = 10 KW 4 = 50 KW 5 = 100 KW L = Assembly Location B = Product Revision (Fixed as “B”) CAT5411Y = Device Code T = Temperature Range (I = Industrial) 3 = Lead Finish − Matte-Tin Y = Production Year (Last Digit) M = Production Month (1−9, O, N, D) XXX = Last Three Digits of Assembly Lot Number L = Assembly Location 3 = Lead Finish − Matte-Tin B = Product Revision (Fixed as “B”) CAT = Fixed as “CAT” 5411W = Device Code T = Temperature Range (I = Industrial) − = Dash RR = Resistance 25 = 2.5 KW 10 = 10 KW 50 = 50 KW 00 = 100 KW Y = Production Year (Last Digit) M = Production Month (1−9, O, N, D) XXXX = Last Four Digits of Assembly Lot Number RH0 CS SCK SI SO SPI BUS INTERFACE RH1 WIPER CONTROL REGISTERS RW0 RW1 WP A0 A1 CONTROL LOGIC NONVOLATILE DATA REGISTERS RL0 Figure 1. Functional Diagram http://onsemi.com 2 RL1 CAT5411 PIN DESCRIPTIONS SI: Serial Input HOLD: Hold SI is the serial data input pin. This pin is used to input all opcodes, byte addresses and data to be written to the CAT5411. Input data is latched on the rising edge of the serial clock. The HOLD pin is used to pause transmission to the CAT5411 while in the middle of a serial sequence without having to re-transmit entire sequence at a later time. To pause, HOLD must be brought low while SCK is low. The SO pin is in a high impedance state during the time the part is paused, and transitions on the SI pins will be ignored. To resume communication, HOLD is brought high, while SCK is low. (HOLD should be held high any time this function is not being used.) HOLD may be tied high directly to VCC or tied to VCC through a resistor. SO: Serial Output SO is the serial data output pin. This pin is used to transfer data out of the CAT5411. During a read cycle, data is shifted out on the falling edge of the serial clock. SCK: Serial Clock SCK is the serial clock pin. This pin is used to synchronize the communication between the microcontroller and the CAT5411. Opcodes, byte addresses or data present on the SI pin are latched on the rising edge of the SCK. Data on the SO pin is updated on the falling edge of the SCK. Table 1. PIN CONNECTIONS Pin SOIC Pin TSSOP Name 1 19 VCC Supply Voltage 2 20 RL0 Low Reference Terminal for Potentiometer 0 3 21 RH0 High Reference Terminal for Potentiometer 0 4 22 RW0 Wiper Terminal for Potentiometer 0 5 23 CS Chip Select 6 24 WP Write Protection The four sets of RH and RL pins are equivalent to the terminal connections on a mechanical potentiometer. 7 1 SI Serial Input 8 2 A1 Device Address RW: Wiper 9 3 RL1 The four RW pins are equivalent to the wiper terminal of a mechanical potentiometer. Low Reference Terminal for Potentiometer 1 10 4 RH1 High Reference Terminal for Potentiometer 1 CS: Chip Select 11 5 RW1 Wiper Terminal for Potentiometer 1 12 6 GND Ground 13 7 NC No Connect 14 8 NC No Connect 15 9 NC No Connect 16 10 NC No Connect 17 11 SCK 18 12 HOLD 19 13 SO Serial Data Output 20 14 A0 Device Address, LSB 21 15 NC No Connect 22 16 NC No Connect 23 17 NC No Connect 24 18 NC No Connect A0, A1: Device Address Inputs These inputs set the device address when addressing multiple devices. A total of four devices can be addressed on a single bus. A match in the slave address must be made with the address input in order to initiate communication with the CAT5411. RH, RL: Resistor End Points CAT5251 and CS high disables the CAT5411. CS high takes the SO output pin to high impedance and forces the devices into a Standby mode (unless an internal write operation is underway). The CAT5411 draws ZERO current in the Standby mode. A high to low transition on CS is required prior to any sequence being initiated. A low to high transition on CS after a valid write sequence is what initiates an internal write cycle. WP: Write Protect WP is the Write Protect pin. The Write Protect pin will allow normal read/write operations when held high. When WP is tied low, all non-volatile write operations to the Data registers are inhibited (change of wiper control register is allowed). WP going low while CS is still low will interrupt a write to the registers. If the internal write cycle has already been initiated, WP going low will have no effect on any write operation. http://onsemi.com 3 Function Bus Serial Clock Hold CAT5411 DEVICE OPERATION The CAT5411 is two resistor arrays integrated with SPI serial interface logic, two 6-bit wiper control registers and eight 6-bit, non-volatile memory data registers. Each resistor array contains 63 separate resistive elements connected in series. The physical ends of each array are equivalent to the fixed terminals of a mechanical potentiometer (RH and RL). RH and RL are symmetrical and may be interchanged. The tap positions between and at the ends of the series resistors are connected to the output wiper terminals (RW) by a CMOS transistor switch. Only one tap point for each potentiometer is connected to its wiper terminal at a time and is determined by the value of the wiper control register. Data can be read or written to the wiper control registers or the non-volatile memory data registers via the SPI bus. Additional instructions allow data to be transferred between the wiper control registers and each respective potentiometer’s non-volatile data registers. Also, the device can be instructed to operate in an “increment/decrement” mode. SERIAL BUS PROTOCOL After the device is selected with CS going low the first byte will be received. The part is accessed via the SI pin, with data being clocked in on the rising edge of SCK. The first byte contains one of the six op-codes that define the operation to be performed. The CAT5041 supports the SPI bus data transmission protocol. The synchronous Serial Peripheral Interface (SPI) helps the CAT5411 to interface directly with many of today’s popular microcontrollers. The CAT5041 contains an 8-bit instruction register. The instruction set and the operation codes are detailed in the instruction set Table 12. Table 2. RELIABILITY CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Parameter Symbol Reference Test Method NEND (Note 1) Endurance MIL−STD−883, Test Method 1033 Min Typ Max Units 1,000,000 Cycles/Byte TDR (Note 1) Data Retention MIL−STD−883, Test Method 1008 100 Years VZAP (Note 1) ESD Susceptibility MIL−STD−883, Test Method 3015 2000 Volts ILTH (Note 1) Latch-up JEDEC Standard 17 100 mA 1. This parameter is tested initially and after a design or process change that affects the parameter. Table 3. ABSOLUTE MAXIMUM RATINGS Ratings Units Temperature Under Bias Parameters −55 to +125 C Storage Temperature Range −65 to +150 C −2.0 to VCC +2.0 V −2.0 to +7.0 V Package Power Dissipation Capability (TA = 25C) 1.0 W Lead Soldering Temperature (10 s) 300 C Wiper Current 12 mA Voltage to any Pins with Respect to VSS (Notes 2, 3) VCC with Respect to GND Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 2. The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5 V, which may overshoot to VCC +2.0 V for periods of less than 20 ns. 3. Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to VCC +1 V. Table 4. RECOMMENDED OPERATING CONDITIONS Parameters Ratings Units VCC +2.5 to 6.0 V Industrial Temperature −40 to +85 C http://onsemi.com 4 CAT5411 Table 5. POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Parameter Symbol Test Conditions Min Typ Max Units RPOT Potentiometer Resistance (−00) 100 kW RPOT Potentiometer Resistance (−50) 50 kW RPOT Potentiometer Resistance (−10) 10 kW RPOT Potentiometer Resistance (−25) 2.5 Potentiometer Resistance Tolerance RPOT Matching Power Rating 25C, each pot IW Wiper Current RW Wiper Resistance IW = +3 mA @ VCC = 3 V RW Wiper Resistance IW = +3 mA @ VCC = 5 V VTERM VN Voltage on any RH or RL Pin VSS = 0 V Noise 80 GND kW +20 % 1 % 50 mW +6 mA 300 W 150 W VCC V (Note 4) Resolution nV/Hz 1.6 % Absolute Linearity (Note 5) RW(n)(actual)−R(n)(expected) (Note 8) +1 LSB (Note 7) Relative Linearity (Note 6) RW(n+1)−[RW(n)+LSB] (Note 8) +0.2 LSB (Note 7) TCRPOT Temperature Coefficient of RPOT (Note 4) TCRATIO Ratiometric Temp. Coefficient (Note 4) CH/CL/CW Potentiometer Capacitances (Note 4) 10/10/25 pF RPOT = 50 kW (Note 4) 0.4 MHz fc Frequency Response +300 ppm/C 20 ppm/C 4. This parameter is tested initially and after a design or process change that affects the parameter. 5. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer. 6. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer. It is a measure of the error in step size. 7. LSB = RTOT / 63 or (RH − RL) / 63, single pot 8. n = 0, 1, 2, ..., 63 Table 6. D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Symbol Parameter Test Conditions Max Units 1 mA VIN = GND or VCC; SO Open 1 mA VIN = GND to VCC 10 mA VOUT = GND to VCC 10 mA −1 VCC x 0.3 V VCC x 0.7 VCC + 1.0 V 0.4 V ICC Power Supply Current fSCK = 2 MHz, SO Open Inputs = GND ISB Standby Current (VCC = 5 V) ILI Input Leakage Current ILO Output Leakage Current VIL Input Low Voltage VIH Input High Voltage VOL1 Output Low Voltage (VCC = 3 V) IOL = 3 mA http://onsemi.com 5 Min CAT5411 Table 7. PIN CAPACITANCE (Note 9) (Applicable over recommended operating range from TA = 25C, f = 1.0 MHz, VCC = +5.0 V (unless otherwise noted).) Test Conditions Max Units Conditions Output Capacitance (SO) 8 pF VOUT = 0 V Input Capacitance (CS, SCK, SI, WP, HOLD) 6 pF VIN = 0 V Symbol COUT CIN Min Typ Table 8. POWER UP TIMING (Note 9) (Over recommended operating conditions unless otherwise stated.) Max Units tPUR (Note 10) Symbol Power-up to Read Operation Parameter Min Typ 1 ms tPUW (Note 10) Power-up to Write Operation 1 ms 9. This parameter is tested initially and after a design or process change that affects the parameter. 10. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. Table 9. ELECTRICAL CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Symbol Parameter Test Conditions Min Typ Max Units tSU Data Setup Time 50 ns tH Data Hold Time 50 ns tWH SCK High Time 125 ns tWL SCK Low Time 125 ns fSCK Clock Frequency DC 3 MHz HOLD to Output Low Z 50 ns tRI (Note 11) Input Rise Time 2 ms tFI (Note 11) Input Fall Time 2 ms tLZ tHD HOLD Setup Time tCD HOLD Hold Time tWC Write Cycle Time tV CL = 50 pF 100 ns 100 ns Output Valid from Clock Low 5 ms 250 ns tHO Output Hold Time tDIS Output Disable Time 0 250 ns ns tHZ HOLD to Output High Z 100 ns tCS CS High Time 250 ns tCSS CS Setup Time 250 ns tCSH CS Hold Time 250 ns 11. This parameter is tested initially and after a design or process change that affects the parameter. Table 10. POTENTIOMETER AC CHARACTERISTICS Symbol Parameter Max Units tWRL Wiper response time after instruction issued (all load instructions) 10 ms tWRID Wiper response time from an active SCK edge (Increment/decrement instruction) 5 ms http://onsemi.com 6 CAT5411 tCS VIH CS VIL tCSS SCK VIH tWL tWH VIL tH tSU VIH SI tCSH VALID IN VIL tRI tFI tV SO VOH tHO tDIS HI−Z HI−Z VOL Figure 2. Synchronous Data Timing CS tCD tCD SCK tHD tHD HOLD tHZ HIGH IMPEDANCE SO tLZ Figure 3. HOLD Timing http://onsemi.com 7 CAT5411 INSTRUCTION AND REGISTER DESCRIPTION Device Type/Address Byte Instruction Byte The first byte sent to the CAT5411 from the master/ processor is called the Device Address Byte. The most significant four bits of the Device Type address are a device type identifier. These bits for the CAT5411 are fixed at 0101[B] (refer to Figure 4). The two least significant bits in the slave address byte, A1 − A0, are the internal slave address and must match the physical device address which is defined by the state of the A1 − A0 input pins for the CAT5411 to successfully continue the command sequence. Only the device which slave address matches the incoming device address sent by the master executes the instruction. The A1 − A0 inputs can be actively driven by CMOS input signals or tied to VCC or VSS. The remaining two bits in the device address byte must be set to 0. The next byte sent to the CAT5411 contains the instruction and register pointer information. The four most significant bits used provide the instruction opcode I [3:0]. The R1 and R0 bits point to one of the four data registers of each associated potentiometer. The least two significant bits point to one of two Wiper Control Registers. The format is shown in Figure 5. Table 11. DATA REGISTER SELECTION Data Register Selected R1 R0 DR0 0 0 DR1 0 1 DR2 1 0 DR3 1 1 Device Type Identifier ID3 0 ID2 ID1 1 0 Slave Address ID0 0 0 A1 A0 1 (MSB) (LSB) Figure 4. Identification Byte Format 0101 Device Type Identifier (MSB) Instruction Opcode I3 I2 (MSB) I1 WCR/Pot Selection Data Register Selection I0 R1 R0 0 P0 (LSB) Figure 5. Instruction Byte Format CS SCK SI ... ... MSB tWRL LSB VW/RW SO High Impedance Figure 6. Potentiometer Timing (for All Load Instructions) WIPER CONTROL AND DATA REGISTERS Wiper Control Register (WCR) transferring the contents of one of four associated Data Registers via the XFR Data Register instruction, it can be modified one step at a time by the Increment/Decrement instruction (see Instruction section for more details). Finally, it is loaded with the content of its data register zero (DR0) upon power-up. The CAT5411 contains two 6-bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 64 switches along its resistor array. The contents of the WCR can be altered in four ways: it may be written by the host via Write Wiper Control Register instruction; it may be written by http://onsemi.com 8 CAT5411 Registers and the associated Wiper Control Register. Any data changes in one of the Data Registers is a non-volatile operation and will take a maximum of 5 ms. The Wiper Control Register is a volatile register that loses its contents when the CAT5411 is powered-down. Although the register is automatically loaded with the value in DR0 upon power-up, this may be different from the value present at power-down. Write in Process The contents of the Data Registers are saved to nonvolatile memory when the CS input goes HIGH after a write sequence is received. The status of the internal write cycle can be monitored by issuing a Read Status command to read the Write in Process (WIP) bit. Data Registers (DR) Each potentiometer has four 6-bit non-volatile Data Registers. These can be read or written directly by the host. Data can also be transferred between any of the four Data INSTRUCTIONS Four of the ten instructions are three bytes in length. These instructions are:  Read Wiper Control Register – read the current wiper position of the selected potentiometer in the WCR  Write Wiper Control Register – change current wiper position in the WCR of the selected potentiometer  Read Data Register – read the contents of the selected   Data Register Write Data Register – write a new value to the selected Data Register Read Status – Read the status of the WIP bit which when set to “1” signifies a write cycle is in progress. Table 12. INSTRUCTION SET (Note: 1/0 = data is one or zero) Instruction Set Instruction I3 I2 I1 I0 R1 R0 0 WCR0/ P0 Read Wiper Control Register 1 0 0 1 0 0 0 1/0 Read the contents of the Wiper Control Register pointed to by P0 Write Wiper Control Register 1 0 1 0 0 0 0 1/0 Write new value to the Wiper Control Register pointed to by P0 Read Data Register 1 0 1 1 1/0 1/0 0 1/0 Read the contents of the Data Register pointed to by P0 and R1−R0 Write Data Register 1 1 0 0 1/0 1/0 0 1/0 Write new value to the Data Register pointed to by P0 and R1−R0 XFR Data Register to Wiper Control Register 1 1 0 1 1/0 1/0 0 1/0 Transfer the contents of the Data Register pointed to by P0 and R1−R0 to its associated Wiper Control Register XFR Wiper Control Register to Data Register 1 1 1 0 1/0 1/0 0 1/0 Transfer the contents of the Wiper Control Register pointed to by P0 to the Data Register pointed to by R1−R0 Global XFR Data Registers to Wiper Control Registers 0 0 0 1 1/0 1/0 0 0 Transfer the contents of the Data Registers pointed to by R1−R0 of all four pots to their respective Wiper Control Registers Global XFR Wiper Control Registers to Data Register 1 0 0 0 1/0 1/0 0 0 Transfer the contents of both Wiper Control Registers to their respective data Registers pointed to by R1−R0 of all four pots Increment/Decrement Wiper Control Register 0 0 1 0 0 0 0 1/0 Enable Increment/decrement of the Control Latch pointed to by P0 Read Status 0 1 0 1 0 0 0 1 Operations Read WIP bit to check internal write cycle status associated registers; or the transfer can occur between all potentiometers and one associated register. Four instructions require a two-byte sequence to complete, as illustrated in Figure 7. These instructions transfer data between the host/processor and the CAT5411; either between the host and one of the data registers or directly between the host and the Wiper Control Register. These instructions are: The basic sequence of the three byte instructions is illustrated in Figure 8. These three-byte instructions exchange data between the WCR and one of the Data Registers. The WCR controls the position of the wiper. The response of the wiper to this action will be delayed by tWRL. A transfer from the WCR (current wiper position), to a Data Register is a write to non-volatile memory and takes a minimum of tWR to complete. The transfer can occur between one of the four potentiometers and one of its http://onsemi.com 9 CAT5411 Increment/Decrement Command  XFR Data Register to Wiper Control Register    The final command is Increment/Decrement (Figures 9 and 10). The Increment/Decrement command is different from the other commands. Once the command is issued the master can clock the selected wiper up and/or down in one segment steps; thereby providing a fine tuning capability to the host. For each SCK clock pulse (tHIGH) while SI is HIGH, the selected wiper will move one resistor segment towards the RH terminal. Similarly, for each SCK clock pulse while SI is LOW, the selected wiper will move one resistor segment towards the RL terminal. See Instructions format for more detail. This transfers the contents of one specified Data Register to the associated Wiper Control Register. XFR Wiper Control Register to Data Register This transfers the contents of the specified Wiper Control Register to the specified associated Data Register. Global XFR Data Register to Wiper Control Register This transfers the contents of all specified Data Registers to the associated Wiper Control Registers. Global XFR Wiper Counter Register to Data Register This transfers the contents of all Wiper Control Registers to the specified associated Data Registers. SI 0 1 0 1 0 0 ID3 ID2 ID1 ID0 A3 A2 A1 A0 Internal Address Device ID I3 I2 I1 I0 R1 R0 0 P0 Instruction Opcode Register Pot/WCR Address Address Figure 7. Two-byte Instruction Sequence 0 SI 1 0 1 0 0 ID3 ID2 ID1 ID0 A3 A2 A1 A0 I3 Internal Address Device ID I2 I0 R1 R0 0 P0 D7 D6 D5 D4 D3 D2 D1 D0 I1 Instruction Opcode Data Pot/WCR Register Address Address WCR[7:0] or Data Register D[7:0] Figure 8. Three-byte Instruction Sequence SI 0 1 0 1 0 0 ID3 ID2 ID1 ID0 A3 A2 A1 A0 Device ID Internal Address I3 I2 I1 I0 Instruction Opcode R1 R0 0 P0 I N C Data Pot/WCR Register Address 1 Address I N C 2 I N C n Figure 9. Increment/Decrement Instruction Sequence INC/DEC Command Issued tWRL SCK SI RW Voltage Out Figure 10. Increment/Decrement Timing Limits http://onsemi.com 10 D E C 1 D E C n CAT5411 INSTRUCTION FORMAT Table 13. READ WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 INSTRUCTION A0 1 0 0 1 0 0 CS DATA 0 P0 7 6 0 0 5 4 3 2 1 0 Table 14. WRITE WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 INSTRUCTION A0 1 0 1 0 0 0 CS DATA 0 P0 7 6 0 0 5 4 3 2 1 0 Table 15. READ DATA REGISTER (DR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 INSTRUCTION A0 1 0 1 1 R1 R0 CS DATA 0 P0 7 6 5 4 3 2 1 0 Table 16. WRITE DATA REGISTER (DR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 INSTRUCTION A0 1 1 0 0 R1 R0 CS DATA 0 P0 7 6 5 4 3 2 1 0 Table 17. READ STATUS (WIP) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 INSTRUCTION A0 0 1 0 1 0 0 CS DATA 0 1 7 6 0 0 5 4 3 2 1 W I P Table 18. GLOBAL TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 CS INSTRUCTION A0 0 0 0 1 R1 R0 0 0 Table 19. GLOBAL TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 CS INSTRUCTION A0 1 0 0 0 R1 R0 0 0 http://onsemi.com 11 High Voltage Write Cycle High Voltage Write Cycle CAT5411 Table 20. TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 CS INSTRUCTION A0 1 1 1 0 R1 R0 0 P0 High Voltage Write Cycle Table 21. TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 CS INSTRUCTION A0 1 1 0 1 R1 R0 0 P0 Table 22. INCREMENT (I)/DECREMENT (D) WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESS 0 1 0 1 0 0 A1 INSTRUCTION A0 0 0 1 0 0 0 CS DATA 0 P0 I/D I/D I/D I/D ... NOTE: Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after CS goes high. Table 23. ORDERING INFORMATION Orderable Part Number Resistance (kW) CAT5411WI-25-T1 2.5 CAT5411WI-10-T1 10 CAT5411WI-50-T1 50 CAT5411WI-00-T1 100 CAT5411YI-25-T2 2.5 CAT5411YI-10-T2 10 CAT5411YI-50-T2 50 CAT5411YI-00-T2 100 CAT5411WI25 2.5 CAT5411WI10 10 CAT5411WI50 50 CAT5411WI00 100 CAT5411YI25 2.5 CAT5411YI10 10 CAT5411YI50 50 CAT5411YI00 100 Lead Finish Package Shipping† SOIC−24 (Pb-Free) 1,000 / Tape & Reel TSSOP24 (Pb-Free) 2,000 / Tape & Reel SOIC−24 (Pb-Free) 31 Units / Tube TSSOP24 (Pb-Free) 62 Units / Tube Matte-Tin †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 12. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com. 13. All packages are RoHS-compliant (Pb-Free, Halogen Free). 14. The standard lead finish is Matte-Tin. http://onsemi.com 12 CAT5411 PACKAGE DIMENSIONS SOIC−24, 300 mils CASE 751BK ISSUE O E1 SYMBOL MIN A 2.35 2.65 A1 0.10 0.30 A2 2.05 2.55 b 0.31 0.51 c 0.20 0.33 D 15.20 15.40 E 10.11 10.51 E1 7.34 7.60 E e PIN#1 IDENTIFICATION MAX 1.27 BSC e b NOM h 0.25 0.75 L 0.40 1.27 θ 0º 8º θ1 5º 15º TOP VIEW h D A2 A A1 SIDE VIEW h q1 q q1 L END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-013. http://onsemi.com 13 c CAT5411 PACKAGE DIMENSIONS TSSOP24, 4.4x7.8 CASE 948AR ISSUE A b SYMBOL MIN NOM A E1 E MAX 1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 7.70 7.80 7.90 E 6.25 6.40 6.55 E1 4.30 4.40 4.50 e L 0.65 BSC 0.50 L1 θ 0.60 0.70 1.00 REF 0º 8º e TOP VIEW D c A2 A θ1 L A1 SIDE VIEW END VIEW L1 Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAT5411/D