CAT9534YI-GT2

CAT9534 8-bit I²C and SMBus I/O Port with Interrupt FEATURES  400kHz I²C bus compatible  2.3V to 5.5V operation  Low stand-by current  5V tolerant I/Os  8 I/O pins that default to inputs at power-up  High drive capability  Individual I/O configuration  Polarity inversion register  Active low interrupt output  Internal power-on reset  No glitch on power-up  Noise filter on SDA/SCL inputs  Cascadable up to 8 devices  Industrial temperature range  RoHS-compliant 16-lead SOIC and TSSOP, and 16-pad TQFN (4 x 4mm) packages DESCRIPTION The CAT9534 is an 8-bit parallel input/output port expander for I²C and SMBus compatible applications. These I/O expanders provide a simple solution in applications where additional I/Os are needed: sensors, power switches, LEDs, pushbuttons, and fans. The CAT9534 consists of an input port register, an output port register, a configuration register, a polarity inversion register and an I²C/SMBus-compatible serial interface. Any of the eight I/Os can be configured as an input or output by writing to the configuration register. The system master can invert the CAT9534 input data by writing to the active-high polarity inversion register. The CAT9534 features an active low interrupt output which indicates to the system master that an input state has changed. The device’s extended addressing capability allows up to 8 devices to share the same bus. CAT9534 is offered in 16 pin SOIC, TSSOP and TQFN packages and operates over the full -40ºC to +85ºC industrial temperature range. For Ordering Information details, see page 15. APPLICATIONS  White goods (dishwashers, washing machines)  Handheld devices (cell phones, PDAs, digital cameras)  Data Communications (routers, hubs and servers) BLOCK DIAGRAM A0 A1 A2 SCL SDA (1) I/O0 I/O1 8-BIT INPUT FILTER I2C/SMBUS CONTROL WRITE pulse READ pulse INPUT/ OUTPUT PORTS I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 LP FILTER INT VCC VCC VSS POWER-ON RESET Notes: (1) All I/Os are set to inputs at RESET. © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 1 Doc. No. MD-9004 Rev. D CAT9534 PIN CONFIGURATION SOIC (W), TSSOP (Y) A0 1 A1 2 A2 3 I/O0 4 I/O1 5 I/O2 6 I/O3 7 VSS 8 16 VCC 15 SDA 14 SCL 13 INT 12 I/O7 11 TQFN 4 x 4mm (HV4) (Top View) A1 16 A2 I/O0 I/O1 I/O2 1 2 3 4 5 6 7 8 A0 15 VCC SDA 14 13 12 SCL 11 INT 10 I/O7 9 I/O6 I/O6 10 I/O5 9 I/O4 I/O3 VSS I/O4 I/O5 PIN DESCRIPTION SOIC / TSSOP 1 2 3 4-7 8 9-12 13 14 15 16 TQFN 15 16 1 2-5 6 7-10 11 12 13 14 Pin Name A0 A1 A2 I/O0-3 VSS I/O4-7 ¯¯¯ INT SCL SDA VCC Function Address Input 0 Address Input 1 Address Input 2 Input/Output Port 0 to Input/Output Port 3 Ground Input/Output Port 4 to Input/Output Port 7 Interrupt Output (open drain) Serial Clock Serial Data Power Supply ABSOLUTE MAXIMUM RATINGS (1) Parameters VCC with Respect to Ground Voltage on Any Pin with Respect to Ground DC Current on I/O0 to I/O7 DC Input Current VCC Supply Current VSS Supply Current Package Power Dissipation Capability (TA = 25°C) Junction Temperature Storage Temperature Ratings -0.5 to +6.5 -0.5 to +5.5 ±50 ±20 85 100 1.0 +150 -65 to +150 Units V V mA mA mA mA W ºC ºC RELIABILITY CHARACTERISTICS Symbol (2) VZAP (2)(3) ILTH Parameter ESD Susceptibility Latch-up Reference Test Method JEDEC Standard JESD 22 JEDEC Standard 17 Min 2000 100 Units Volts mA Notes: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. (2) This parameter is tested initially and after a design or process change that affects the parameter. (3) Latch-up protection is provided for stresses up to 100mA on address and data pins from -1V to VCC +1V. Doc. No. MD-9004 Rev. D 2 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 D.C. OPERATING CHARACTERISTICS VCC = 2.3 to 5.5V; TA = -40°C to +85°C, unless otherwise specified. Symbol Supplies VCC ICC Istbl Istbh VPOR VIL VIH (1) (1) Parameter Supply voltage Supply current Standby current Standby current Power-on reset voltage Low level input voltage Conditions Min 2.3 Typ — 104 0.25 0.25 1.5 — — — — — — — — — — — 10 13 17 24 14 19 — — — — — — — — — Max 5.5 175 3 1 1.65 0.3 x VCC 5.5 — +1 6 8 0.8 5.5 1 0.8 5.5 — — — — — — — — — — — — 1 5 8 Unit V µA µA µA V V V mA µA pF pF V V µA V V mA mA mA mA mA mA V V V V V V µA pF pF Operating mode; VCC = 5.5V; no load; fSCL = 100kHz Standby mode; VCC = 5.5V; no load; VI = VSS; fSCL = 0kHz; I/O = inputs Standby mode; VCC = 5.5V; no load; VI = VCC; fSCL = 0kHz; I/O = inputs No load; VI = VCC or VSS — — — — -0.5 0.7 x VCC SCL, SDA, ¯¯¯ INT High level input voltage Low level output IOL current IL Leakage current (2) CI Input capacitance (2) CO Output capacitance A0, A1, A2 (1) VIL Low level input voltage (1) VIH High level input voltage ILI Input leakage current I/Os VIL Low level input voltage VIH High level input voltage VOL = 0.4V VI = VCC or VSS VI = VSS VO = VSS 3 -1 — — -0.5 2.0 -1 -0.5 2.0 8 10 8 10 8 10 1.8 1.7 2.6 2.5 4.1 4.0 — — — IOL Low level output current VOH High level output voltage IL (2) CI (2) CO Input leakage current Input capacitance Output capacitance VOL = 0.5V; VCC = 2.3V (3) VOL = 0.7 V; VCC = 2.3 V (3) VOL = 0.5 V; VCC = 4.5 V (3) VOL = 0.7 V; VCC = 4.5 V (3) VOL = 0.5 V; VCC = 3.0 V (3) VOL = 0.7 V; VCC = 3.0 V (4) IOH = -8 mA; VCC = 2.3 V (4) IOH = -10 mA; VCC = 2.3 V (4) IOH = - 8 mA; VCC = 3.0 V (4) IOH = -10 mA; VCC = 3.0 V (4) IOH = -8 mA; VCC = 4.75 V (4) IOH = -10 mA; VCC = 4.75 V VCC = 3.6V; VI = VCC (3) Notes: (1) VIL min and VIH max are reference values only and are not tested. (2) This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested. (3) The total current sunk by all I/Os must be limited to 100mA and each I/O limited to 25mA maximum. (4) The total current sourced by all I/Os must be limited to 85mA. © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 3 Doc. No. MD-9004 Rev. D CAT9534 A.C. CHARACTERISTICS VCC = 2.3 to 5.5V; TA = -40°C to +85°C, unless otherwise specified. Symbol FSCL tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF (2) (2) (1) 2 2 Standard I C Parameter Min Clock Frequency START Condition Hold Time Low Period of SCL Clock High Period of SCL Clock START Condition Setup Time Data In Hold Time Data In Setup Time SDA and SCL Rise Time SDA and SCL Fall Time STOP Condition Setup Time Bus Free Time Between STOP and START SCL Low to Data Out Valid Data Out Hold Time Noise Pulse Filtered at SCL and SDA Inputs Parameter Output Data Valid Input Data Setup Time Input Data Hold Time Interrupt Valid Interrupt Reset 100 100 4 4.7 3.5 4 4.7 4 4.7 0 250 1000 300 Max 100 Fast I C Units Min 0.6 1.3 0.6 0.6 0 100 300 300 0.6 1.3 0.9 50 100 Min Max 200 100 1 4 4 Max 400 kHz µs µs µs µs µs ns ns ns µs µs µs ns ns Units ns ns µs µs µs tSU:STO (2) tBUF tAA tDH Ti (2) Symbol Port Timing tPV tPS tPH tIV tIR Interrupt Timing Notes: (1) Test conditions according to "AC Test Conditions" table. (2) This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested. Doc. No. MD-9004 Rev. D 4 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 A.C. TEST CONDITIONS Input Rise and Fall time CMOS Input Voltages CMOS Input Reference Voltages TTL Input Voltages TTL Input Reference Voltages Output Reference Voltages Output Load: SDA, ¯¯¯ INT Output Load: I/Os ≤ 10ns 0.2VCC to 0.8VCC 0.3VCC to 0.7VCC 0.4V to 2.4V 0.8V, 2.0V 0.5VCC Current Source IOL = 3mA; CL = 100pF Current Source: IOL/IOH = 10mA; CL = 50pF tF tLOW SCL tSU:STA tHD:STA tHIGH tLOW tR tHD:DAT tSU:DAT tSU:STO SDA IN tAA SDA OUT tDH tBUF Figure 1. I²C Serial Interface Timing © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 5 Doc. No. MD-9004 Rev. D CAT9534 PIN DESCRIPTION SCL: Serial Clock The serial clock input clocks all data transferred into or out of the device. The SCL line requires a pull-up resistor if it is driven by an open drain output. SDA: Serial Data/Address The bidirectional serial data/address pin is used to transfer all data into and out of the device. The SDA pin is an open drain output and can be wire-ORed with other open drain or open collector outputs. A pullup resistor must be connected from SDA line to VCC. The value of the pull-up resistor, RP, can be calculated based on minimum and maximum values from Figure 2 and Figure 3 (see Note). A0, A1, A2: Device Address Inputs These inputs are used for extended addressing capability. The A0, A1, A2 pins should be hardwired to VCC or VSS. When hardwired, up to eight CAT9534s may be addressed on a single bus system. The levels on these inputs are compared with corresponding bits, A2, A1, A0, from the slave address byte. I/O0 to I/O7: Input / Output Ports Any of these pins may be configured as input or output. The simplified schematic of I/O0 to I/O7 is shown in Figure 4. When an I/O is configured as an input, the Q1 and Q2 output transistors are off creating a high impedance input. If the I/O pin is configured as an output, the push-pull output stage is enabled. Care should be taken if an external voltage is applied to an I/O pin configured as an output due to the low impedance paths that exist between the pin and either VCC or VSS. IOL = 3mA @ VOLmax 2.5 8.00 Fast Mode I²C Bus / tr max - 300ns 7.00 6.00 5.00 4.00 3.00 2.00 1.00 0.00 50 100 150 200 250 300 350 400 RPmin (KΩ) 2 1.5 1 0.5 0 2 2.4 2.8 3.2 3.6 4 4.4 4.8 5.2 5.6 VCC (V) RPmax (KΩ) CBUS (pF) Figure 2. Minimum RP Value versus Supply Voltage Figure 3. Maximum RP Value versus Bus Capacitance Note: According to the Fast Mode I²C bus specification, for bus capacitance up to 200pF, the pull up device can be a resistor. For bus loads between 200pF and 400pF, the pull-up device can be a current source (Imax = 3mA) or a switched resistor circuit. Doc. No. MD-9004 Rev. D 6 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 ¯¯¯: Interrupt Output INT The open-drain interrupt output is activated when one of the port pins configured as an input changes state (differs from the corresponding input port register bit state). The interrupt is deactivated when the input Data from Shift Register Data from Shift Register returns to its previous state or the input port register is read. Changing an I/O from an output to an input may cause a false interrupt if the state of the pin does not match the contents of the input port register. Configuration Register D FF Q Output Port Register Data VCC Q1 Write Configuration Pulse CK Q D FF Q Write Pulse I/O 0 to I/O 7 CK Q Q2 Output Port Register Input Port Register VSS Input Port Register Data D LATCH Read Pulse CK Q Q To INT Data from Shift Register Write Polarity Register D FF CK Q Polarity Register Data Q Polarity Inversion Register Figure 4. Simplified Schematic of I/O0 to I/O7 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 7 Doc. No. MD-9004 Rev. D CAT9534 FUNCTIONAL DESCRIPTION CAT9534’s general purpose input/ output (GPIO) peripherals provide up to eight I/O ports, controlled through an I²C compatible serial interface The CAT9534 supports the I²C Bus data transmission protocol. This I²C Bus protocol defines any device that sends data to the bus to be a transmitter and any device receiving data to be a receiver. The transfer is controlled by the Master device which generates the serial clock and all START and STOP conditions for bus access. The CAT9534 operates as a Slave device. Both the Master device and Slave device can operate as either transmitter or receiver, but the Master device controls which mode is activated. I²C BUS PROTOCOL The features of the I²C bus protocol are defined as follows: (1) Data transfer may be initiated only when the bus is not busy. (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock line is high will be interpreted as a START or STOP condition (Figure 5). START AND STOP CONDITIONS The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT9534 monitors the SDA and SCL lines and will not respond until this condition is met. A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. DEVICE ADDRESSING After the bus Master sends a START condition, a slave address byte is required to enable the CAT9534 for a read or write operation. The four most significant bits of the slave address are fixed as binary 0100 and the next three bits are its individual address bits (Figure 6). The address bits A2, A1 and A0 are used to select which device is accessed from maximum eight devices on the same bus. These bits must compare to their hardwired input pins. The 8th bit following the 7¯¯ bit slave address is the R/W bit that specifies whether a read or write operation is to be performed. When this bit is set to “1”, a read operation is initiated, and when set to “0”, a write operation is selected. Following the START condition and the slave address byte, the CAT9534 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. The CAT9534 then performs a read or a write operation depending on ¯¯ the state of the R/W bit. SCL SDA START CONDITION STOP CONDITION Figure 5. START/STOP Condition SLAVE ADDRESS 0 1 0 0 A2 A1 A0 R/W FIXED PROGRAMMABLE HARDWARE SELECTABLE Figure 6. CAT9534 Slave Address Doc. No. MD-9004 Rev. D 8 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 ACKNOWLEDGE After a successful data transfer, each receiving device is required to generate an acknowledge. The acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. The SDA line remains stable LOW during the HIGH period of the acknowledge related clock pulse (Figure 5). The CAT9534 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8-bit byte. When the CAT9534 begins a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT9534 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. The master must then issue a STOP condition to return the CAT9534 to the standby power mode and place the device in a known state. REGISTERS AND BUS TRANSACTIONS The CAT9534 consists of an input port register, an output port register, a polarity inversion register and a configuration register. Table 1 shows the register address table. Tables 2 to 5 list Register 0 through Register 3 information. Table 1. Register Command Byte Command (hex) 0x00 0x01 0x02 0x03 Protocol Read byte Read/write byte Read/write byte Read/write byte Function Input port register Output port register Polarity inversion register Configuration register The command byte is the first byte to follow the device address byte during a write/read bus transaction. The register command byte acts as a pointer to determine which register will be written or read. The input port register is a read only port. It reflects the incoming logic levels of the I/O pins, regardless of whether the pin is defined as an input or an output by the configuration register. Writes to the input port register are ignored. Table 2. Register 0 – Input Port Register bit default I7 1 I6 1 I5 1 I4 1 I3 1 I2 1 I1 1 I0 1 Table 3. Register 1 – Output Port Register bit default O7 1 O6 1 O5 1 O4 1 O3 1 O2 1 O1 1 O0 1 Table 4. Register 2 – Polarity Inversion Register bit default N7 0 N6 0 N5 0 N4 0 N3 0 N2 0 N1 0 N0 0 Table 5. Register 3 – Configuration Register bit default C7 1 C6 1 C5 1 C4 1 C3 1 C2 1 C1 1 C0 1 BUS RELEASE DELAY (TRANSMITTER) SCL FROM MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START 1 8 9 BUS RELEASE DELAY (RECEIVER) ACK SETUP ACK DELAY Figure 7. Acknowledge Timing © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 9 Doc. No. MD-9004 Rev. D CAT9534 The output port register sets the outgoing logic levels of the I/O ports, defined as outputs by the configuration register. Bit values in this register have no effect on I/O pins defined as inputs. Reads from the output port register reflect the value that is in the flip-flop controlling the output, not the actual I/O pin value. The polarity inversion register allows the user to invert the polarity of the input port register data. If a bit in this register is set (“1”) the corresponding input port data is inverted. If a bit in the polarity inversion register is cleared (“0”), the original input port polarity is retained. The configuration register sets the directions of the ports. Set the bit in the configuration register to enable the corresponding port pin as an input with a high impedance output driver. If a bit in this register is cleared, the corresponding port pin is enabled as an output. At power-up, the I/Os are configured as inputs with a weak pull-up resistor to VCC. Data is transmitted to the CAT9534’s registers using the write mode shown in Figure 8 and Figure 9. The CAT9534’s registers are read according to the timing diagrams shown in Figure 10 and Figure 11. Once a command byte has been sent, the register which was addressed will continue to be accessed by reads until a new command byte will be sent. SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 0 1 0 0 A2 A1 A0 R/W 0 A 0 0 command byte 0 0 0 0 0 1 A data to port DATA 1 acknowledge from slave A P stop condition start condition WRITE TO PORT DATA OUT FROM PO RT acknowledge from slave acknowledge from slave DATA 1 VALID tpv Figure 8. Write to Output Port Register SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 0 1 0 0 A2 A1 A0 R/W 0 A 0 0 command byte 0 0 0 0 1 1/0 A data to register DATA 1 acknowledge from slave A P stop condition start condition WRITE TO REGISTER acknowledge from slave acknowledge from slave Figure 9. Write to Configuration or Polarity Inversion Register Doc. No. MD-9004 Rev. D 10 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 INTERRUPT OUTPUT CAT9534’s interrupt otuput is an active LOW opendrain output that is activated when any port pin configured as an input changes state. The interrupt output is reset when the input returns to its previous state or the Input Port Register is read. Note that changing an I/O from an output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. POWER-ON RESET OPERATION W hen the power supply is applied to VCC pin, an internal power-on reset pulse holds the CAT9534 in a reset state until VCC reaches VPOR level. At this point, the reset condition is released and the internal state machine and the CAT9534’s registers are initialized to their default state. slave address S 0 1 0 0 A2 A1 A0 R/W 0 A COMMAND BYTE acknowledge from slave A S 0 1 slave address 0 0 R/W acknowledge from master data from register DATA first byte A A2 A1 A0 1 A acknowledge from slave acknowledge from slave At this moment master-transmitter becomes master-receiver and slave-receiver becomes slave-transmitter no acknowledge from master data from register DATA last byte NA P Figure 10. Read from Register SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 0 1 0 0 A2 A1 A0 R/W 1 A data from port DATA 1 acknowledge from master A data from port DATA 4 no acknowledge from master NA P stop condition start condition READ FROM PORT DATA INTO PORT acknowledge from slave DATA 1 DATA 2 DATA 3 DATA 4 tPH tPS INT tIV tIR Figure 11. Read Input Port Register © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 11 Doc. No. MD-9004 Rev. D CAT9534 PACKAGE OUTLINE DRAWINGS SOIC 16-Lead 150mils (W) (1) (2) SYMBOL MIN NOM MAX A A1 b c E1 E 1.35 0.10 0.33 0.19 9.80 5.80 3.80 0.25 0.40 0º 9.90 6.00 3.90 1.27 BSC 1.75 0.25 0.51 0.25 10.00 6.20 4.00 0.50 1.27 8º D E E1 e h L θ PIN#1 IDENTIFICATION TOP VIEW D h A θ e b A1 L c SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC standard MS-012 Doc. No. MD-9004 Rev. D 12 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 TSSOP 16-Lead 4.4mm (Y) (1) (2) b SYMBOL MIN NOM MAX A A1 A2 b E1 E 1.10 0.05 0.85 0.19 0.13 4.90 6.30 4.30 0.65 BSC 1.00 REF 0.45 0° 0.75 8° 0.15 0.95 0.30 0.20 5.10 6.50 4.50 c D E E1 e L L1 θ1 PIN#1 IDENTIFICATION TOP VIEW e D c A2 A θ1 A1 L SIDE VIEW END VIEW L1 Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC standard MO-153. © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 13 Doc. No. MD-9004 Rev. D CAT9534 TQFN 16-Pad 4 x 4mm (HV4) (1) (2) D A DETAIL A E E2 PIN#1 ID PIN#1 INDEX AREA A1 SIDE VIEW D2 TOP VIEW BOTTOM VIEW SYMBOL MIN NOM MAX b e A A1 A3 b D D2 E E2 e L 0.70 0.00 0.25 3.90 2.00 3.90 2.00 0.45 0.75 0.02 0.20 REF 0.30 4.00 – 4.00 – 0.65 BSC – 0.80 0.05 0.35 4.10 2.25 4.10 2.25 A L DETAIL A 0.65 A1 FRONT VIEW A3 Notes: (1) All dimensions are in millimeters. (2) Refer to JEDEC standard MO-220. Doc. No. MD-9004 Rev. D 14 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice CAT9534 EXAMPLE OF ORDERING INFORMATION (1) Prefix CAT Optional Company ID Device # 9534 Product Number Suffix W Package W: SOIC Y: TSSOP HV4: TQFN I -G Lead Finish Blank: Matte-Tin G: NiPdAu T2 Tape & Reel T: Tape & Reel 2: 2,000/Reel 9534 Temperature Range I = Industrial (-40ºC to 85ºC) ORDERING PART NUMBER Part Number CAT9534WI-GT2 CAT9534YI-GT2 CAT9534HV4I-GT2 Package SOIC TSSOP TQFN Lead Finish NiPdAu NiPdAu NiPdAu Notes: (1) All packages are RoHS-compliant (Lead-free, Halogen-free). (2) The standard lead finish is NiPdAu. (3) The device used in the above example is a CAT9534WI-GT2 (SOIC, Industrial Temperature, NiPdAu, Tape & Reel, 2,000/Reel). (4) For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. © 2010 SCILLC. All rights reserved Characteristics subject to change without notice 15 Doc. No. MD-9004 Rev. D CAT9534 REVISION HISTORY Date 23-May-08 03-Dec-08 06-May-09 14-June-10 Revisio A B C D Description Initial Issue Update A.C. Characteristics table to include Standard I C and Fast I C. Change logo and fine print to ON Semiconductor Update D.C. Operating Characteristics table (Supplies) Update Order Part Number table 2 2 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center: Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative Doc. No. MD-9004, Rev. D 16 © 2010 SCILLC. All rights reserved Characteristics subject to change without notice