CS3361YDR14G

CS3361 Alternator Voltage Regulator FET Driver The CS3361 integral alternator regulator integrated circuit provides the voltage regulation for automotive, 3−phase alternators. It drives an external logic level N channel enhancement power FET for control of the alternator field current. In the event of a charge fault, a lamp output pin is provided to drive an external darlington transistor capable of switching on a fault indicator lamp. An overvoltage or no Stator signal condition activates the lamp output. This IC has customized current sense circuitry enabling it to drive FET transistors. The CS3361 is available in an SOIC−14 package. www.onsemi.com SOIC−14 D SUFFIX CASE 751A 14 1 Features Drives Logic Level Power NFET 80 V Load Dump Temperature Compensated Regulation Voltage Shorted Field Protection Duty Cycle, Self Clearing This is a Pb−Free Device PIN CONNECTIONS AND MARKING DIAGRAM 1 DD GND NC OSC Lamp NC NC A WL YY WW G 14 CS3361G AWLYWW • • • • • SC NC VCC Sense STATOR NC IGN = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package ORDERING INFORMATION Device Package Shipping† CS3361YDR14G SOIC−14 (Pb−Free) 2500 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2015 March, 2015 − Rev. 11 1 Publication Order Number: CS3361/D CS3361 VCC Load Dump Detection and Protection ENABLE Series Regulator IGN VSUP OSC OSC VSUP Regulator Comparator Sense + + + R − RS Flop Set Dominate Q VREG High Voltage Comparator S Lamp Indicator Device Driver R DELAY + − SC VHV ENABLE LAMP STATOR Timer VSUP GND Figure 1. Block Diagram www.onsemi.com 2 STATOR CS3361 PACKAGE PIN DESCRIPTION PIN NO. PIN SYMBOL FUNCTION 1 Driver Output driver for external power switch. 2 GND Ground. 3, 6, 7, 9, 13 NC 4 OSC Timing capacitor for oscillator. 5 Lamp Base driver for lamp driver indicates no stator signal or overvoltage condition. 8 IGN 10 Stator Stator signal input for stator timer. 11 Sense Battery sense voltage regulator comparator input and protection. 12 VCC Supply for IC. 14 SC Short circuit sensing. No Connection. Switched ignition power up. MAXIMUM RATINGS Rating Value Unit Storage Temperature Range, TS −55 to +165 °C Junction Temperature Range −40 to 150 °C Continuous Supply 27 V ICC Load Dump (@ VCC = 80 Vpeak) 400 mA 260 peak °C Lead Temperature Soldering: Reflow: (SMD styles only) (Note 1) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. 60 second maximum above 183°C. PACKAGE THERMAL DATA SO−14 Unit RΘJC Typical 30 °C/W RΘJA Typical 125 °C/W Parameter www.onsemi.com 3 CS3361 ELECTRICAL CHARACTERISTICS (−40°C < TA < 125°C, −40°C < TJ < 150°C, 9.0 V ≤ VCC ≤ 17 V; unless otherwise specified.) Characteristic Test Conditions Min Typ Max Unit Supply Current Enabled − − − 10 mA Supply Current Disabled − − − 50 μA − 5.5 − 12 V Supply Driver Stage Output High Voltage Output Low Voltage IOL = 25 μA − − 0.35 V Output High Current VDD = 1.2 V −10 −6.0 −4.0 mA Minimum ON Time COSC = 0.022 μF 200 − − μs Minimum Duty Cycle − − 6.0 10 % Short Circuit Duty Cycle − 1.0 − 5.0 % Field Switch Turn On Rise Time − 15 − 75 μs Field Switch Turn On Fall Time − 15 − 75 μs Input High Voltage − 10 − − V Input Low Voltage − − − 6.0 V 6.0 100 600 ms Stator Stator Time Out High to Low Lamp Output High Current VLAMP @ 3.0 V − − 50 μA Output Low Voltage ILAMP @ 30 mA − − 0.35 V Ignition Input High Voltage ICC > 1.0 mA 1.8 − − V Input Low Voltage ICC < 100 μA − − 0.5 V Oscillator Frequency COSC = 0.022 μF 90 − 210 Hz Rise Time/Fall Time COSC = 0.022 μF − 17 − − Oscillator High Threshold COSC = 0.022 μF − − 4.5 V −10 − +10 μA 13.8 − 15.8 V 0.10 − 0.25 V 1.083 − 1.190 V/V 0.020 − 0.600 V Oscillator Battery Sense Input Current Regulation Voltage Proportional Control High Voltage Threshold Ratio High Voltage Hysteresis − @25°C, R1 = 100 kΩ, R2 = 50 kΩ − VHigh Voltage@LampOn VRegulation@50%Duty Cycle − Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 4 CS3361 TYPICAL PERFORMANCE CHARACTERISTICS 15.5 Battery Voltage 15 14.5 14 13.5 13 −40 −20 0 20 40 60 Temperature (°C) 80 100 120 Figure 2. CS3361 Battery Voltage vs. Temperature (°C) Over Process Variation www.onsemi.com 5 CS3361 APPLICATIONS INFORMATION is detected on the sense pin. This causes the darlington lamp drive transistor to switch on and pull current through the lamp. If the system voltage continues to increase, the field and lamp output turn off as in an overvoltage or load dump condition. The SC or Short Circuit pin monitors the field voltage. If the drive output and the SC voltage are simultaneously high for a predetermined period, a short circuit condition is assumed and the output is disabled. The regulator is forced to a minimum short circuit duty cycle. The CS3361 is designed for use in an alternator charging system. In a standard alternator design (Figure 3), the rotor carries the field winding. An alternator rotor usually has several N and S poles. The magnetic field for the rotor is produced by forcing current through a field or rotor winding. The Stator windings are formed into a number of coils spaced around a cylindrical core. The number of coils equals the number of pairs of N and S poles on the rotor. The alternating current in the Stator windings is rectified by the diodes and applied to the regulator. By controlling the amount of field current, the magnetic field strength is controlled and hence the output voltage of the alternator. Referring to Figure 7, a typical application diagram, the oscillator frequency is set by an external capacitor connected between OSC and ground. The sawtooth waveform ramps between 1.0 V and 3.0 V and provides the timing for the system. For the circuit shown the oscillator frequency is approximately 140 Hz. The alternator voltage is sensed at Terminal A via the resistor divider network R1/R2 on the Sense pin of the IC. The voltage at the sense pin determines the duty cycle for the regulator. The voltage is adjusted by potentiometer R2. A relatively low voltage on the sense pin causes a long duty cycle that increases the Field current. A high voltage results in a short duty cycle. The ignition Terminal (I) switches power to the IC through the VCC pin. The Stator pin monitors the voltage from the stator and senses a stopped engine condition. It drives the Lamp pin high after the stator timeout expires. The Lamp pin also goes high when an overvoltage condition A Regulator STATOR Winding I S Lamp Indicator IGNITION SWITCH FIELD GND FIELD Winding Figure 3. IAR System Block Diagram www.onsemi.com 6 BATT CS3361 REGULATION WAVEFORMS Figure 4 shows typical steady−state operation. A 50% duty cycle is maintained. Figure 5 shows the effect of a drop in voltage on (VBAT/N + VOSC). Notice the duty cycle increase to the field drive. Figure 6 shows the effect of an increase in voltage (above the regulation voltage) on (VBAT/N + VOSC). Notice the decrease in field drive. The CS3361 utilizes proportion control to maintain regulation. Waveforms depicting operation are shown in Figures 4, 5 and 6, where VBAT/N is the divided down voltage present on the Sense pin using R1 and R2 (Figure 7). A sawtooth waveform is generated internally. The amplitude of this waveform is listed in the electric parameter section as proportion control. The oscillator voltage is summed with VBAT/N, and compared with the internal voltage regulator (VREG) in the regulation comparator which controls the field through the output “Device Driver.” VBAT/N + VOSC VREG VBAT/N + VOSC VREG ÌÌ ÌÌ VBAT/N + VOSC VREG ÌÌ ÌÌ Field Driver On ÌÌ ÌÌ Field Driver On Figure 4. 50% Duty Cycle, Steady State Field Driver On Figure 5. > 50% Duty Cycle, Increased Load Figure 6. < 50% Duty Cycle, Decreased Load RECTIFIER MR2502 MR2502 MR2502 MR2502 MR2502 MR2502 STATOR S 250 Ω R3 C1 0.1 μF *C2 10 μF R1 100 kΩ C3 0.047 μF VCC Sense R2 50 kΩ A R4 18 kΩ STATOR D1 MR2502 R5 SC 10 kΩ Driver OSC F Logic level Q1 N Channel MTB20N20E FIELD IGN C4 0.022 μF R7 10 Ω LAMP GND POWER GROUND R6 20 kΩ R9 2.4 kΩ I Lamp Indicator R10 510 Ω IGNITION SWITCH BATTERY MPSA13 *Note: C2 optional for reduced jitter. Figure 7. Typical Application DIagram www.onsemi.com 7 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC−14 NB CASE 751A−03 ISSUE L 14 1 SCALE 1:1 D DATE 03 FEB 2016 A B 14 8 A3 E H L 1 0.25 B M DETAIL A 7 13X M b 0.25 M C A S B S 0.10 X 45 _ M A1 e DETAIL A h A C SEATING PLANE DIM A A1 A3 b D E e H h L M MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.19 0.25 0.35 0.49 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ INCHES MIN MAX 0.054 0.068 0.004 0.010 0.008 0.010 0.014 0.019 0.337 0.344 0.150 0.157 0.050 BSC 0.228 0.244 0.010 0.019 0.016 0.049 0_ 7_ GENERIC MARKING DIAGRAM* SOLDERING FOOTPRINT* 6.50 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF AT MAXIMUM MATERIAL CONDITION. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSIONS. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 14 14X 1.18 XXXXXXXXXG AWLYWW 1 1 1.27 PITCH XXXXX A WL Y WW G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. 14X 0.58 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. STYLES ON PAGE 2 DOCUMENT NUMBER: DESCRIPTION: 98ASB42565B SOIC−14 NB Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 2 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com SOIC−14 CASE 751A−03 ISSUE L DATE 03 FEB 2016 STYLE 1: PIN 1. COMMON CATHODE 2. ANODE/CATHODE 3. ANODE/CATHODE 4. NO CONNECTION 5. ANODE/CATHODE 6. NO CONNECTION 7. ANODE/CATHODE 8. ANODE/CATHODE 9. ANODE/CATHODE 10. NO CONNECTION 11. ANODE/CATHODE 12. ANODE/CATHODE 13. NO CONNECTION 14. COMMON ANODE STYLE 2: CANCELLED STYLE 3: PIN 1. NO CONNECTION 2. ANODE 3. ANODE 4. NO CONNECTION 5. ANODE 6. NO CONNECTION 7. ANODE 8. ANODE 9. ANODE 10. NO CONNECTION 11. ANODE 12. ANODE 13. NO CONNECTION 14. COMMON CATHODE STYLE 4: PIN 1. NO CONNECTION 2. CATHODE 3. CATHODE 4. NO CONNECTION 5. CATHODE 6. NO CONNECTION 7. CATHODE 8. CATHODE 9. CATHODE 10. NO CONNECTION 11. CATHODE 12. CATHODE 13. NO CONNECTION 14. COMMON ANODE STYLE 5: PIN 1. COMMON CATHODE 2. ANODE/CATHODE 3. ANODE/CATHODE 4. ANODE/CATHODE 5. ANODE/CATHODE 6. NO CONNECTION 7. COMMON ANODE 8. COMMON CATHODE 9. ANODE/CATHODE 10. ANODE/CATHODE 11. ANODE/CATHODE 12. ANODE/CATHODE 13. NO CONNECTION 14. COMMON ANODE STYLE 6: PIN 1. CATHODE 2. CATHODE 3. CATHODE 4. CATHODE 5. CATHODE 6. CATHODE 7. CATHODE 8. ANODE 9. ANODE 10. ANODE 11. ANODE 12. ANODE 13. ANODE 14. ANODE STYLE 7: PIN 1. ANODE/CATHODE 2. COMMON ANODE 3. COMMON CATHODE 4. ANODE/CATHODE 5. ANODE/CATHODE 6. ANODE/CATHODE 7. ANODE/CATHODE 8. ANODE/CATHODE 9. ANODE/CATHODE 10. ANODE/CATHODE 11. COMMON CATHODE 12. COMMON ANODE 13. ANODE/CATHODE 14. ANODE/CATHODE STYLE 8: PIN 1. COMMON CATHODE 2. ANODE/CATHODE 3. ANODE/CATHODE 4. NO CONNECTION 5. ANODE/CATHODE 6. ANODE/CATHODE 7. COMMON ANODE 8. COMMON ANODE 9. ANODE/CATHODE 10. ANODE/CATHODE 11. NO CONNECTION 12. ANODE/CATHODE 13. ANODE/CATHODE 14. COMMON CATHODE DOCUMENT NUMBER: DESCRIPTION: 98ASB42565B SOIC−14 NB Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 2 OF 2 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative