LM323AT

ON Semiconductort 3.0 A Positive Voltage Regulators The LM323,A are monolithic integrated circuits which supply a fixed positive 5.0 V output with a load driving capability in excess of 3.0 A. These three–terminal regulators employ internal current limiting, thermal shutdown, and safe–area compensation. The A–suffix is an improved device with superior electrical characteristics and a 2% output voltage tolerance. These regulators are offered with a 0° to +125°C temperature range in a low cost plastic power package. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. These devices can be used with a series pass transistor to supply up to 15 A at 5.0 V. • Output Current in Excess of 3.0 A • Available with 2% Output Voltage Tolerance • No External Components Required • Internal Thermal Overload Protection • Internal Short Circuit Current Limiting • Output Transistor Safe–Area Compensation • Thermal Regulation and Ripple Rejection Have Specified Limits LM323, LM323A 3–AMPERE, 5 VOLT POSITIVE VOLTAGE REGULATORS SEMICONDUCTOR TECHNICAL DATA T SUFFIX PLASTIC PACKAGE CASE 221A Pin 1. Input 2. Ground 3. Output 1 2 3 Heatsink surface is connected to Pin 2. ORDERING INFORMATION Output Voltage Tolerance 4% 2% Operating Temperature Range TJ = 0° to +125°C Device LM323T LM323AT Package Plastic Power Simplified Application Input Cin* 0.33µF LM323, A Output CO** A common ground is required between the input and the output voltages. The input voltage must remain typically 2.5 V above the output voltage even during the low point on the input ripple voltage. *Cin is required if regulator is located an appreciable *distance from power supply filter. (See Applications *Information for details.) **CO is not needed for stability; however, it does **improve transient response. © Semiconductor Components Industries, LLC, 2002 1 January, 2002 – Rev. 2 Publication Order Number: LM323/D LM323, LM323A MAXIMUM RATINGS Rating Input Voltage Power Dissipation Operating Junction Temperature Range Storage Temperature Range Lead Temperature (Soldering, 10 s) Symbol Vin PD TJ Tstg Tsolder Value 20 Internally Limited 0 to +125 –65 to +150 300 Unit Vdc W °C °C °C ELECTRICAL CHARACTERISTICS (TJ = Tlow to Thigh [Note 1], unless otherwise noted.) LM323A Characteristics Output Voltage (Vin = 7.5 V, 0 ≤ Iout ≤ 3.0 A, TJ = 25°C) Output Voltage (7.5 V ≤ Vin ≤ 15 V, 0 ≤ Iout ≤ 3.0 A, P ≤ Pmax) (Note 2) Line Regulation (7.5 V ≤ Vin ≤ 15 V, TJ = 25°C) (Note 3) Load Regulation (Vin = 7.5 V, 0 ≤ Iout ≤ 3.0 A, TJ = 25°C) (Note 3) Thermal Regulation (Pulse = 10 ms, P = 20 W, TA = 25°C) Quiescent Current (7.5 V ≤ Vin ≤ 15 V, 0 ≤ Iout ≤ 3.0 A) Output Noise Voltage (10 Hz ≤ f ≤ 100 kHz, TJ = 25°C) Ripple Rejection (8.0 V ≤ Vin ≤ 18 V, Iout = 2.0A, f = 120 Hz, TJ = 25°C) Short Circuit Current Limit (Vin = 15 V, TJ = 25°C) (Vin = 7.5 V, TJ = 25°C) Long Term Stability Thermal Resistance, Junction–to–Case (Note 4) Symbol VO VO Min 4.9 4.8 Typ 5.0 5.0 Max 5.1 5.2 Min 4.8 4.75 LM323 Typ 5.0 5.0 Max 5.2 5.25 Unit V V Regline Regload – – 1.0 10 15 50 – – 1.0 10 25 100 mV mV Regtherm IB VN RR – – – 66 0.001 3.5 40 75 0.01 10 – – – – – 62 0.002 3.5 40 75 0.03 20 – – %VO/W mA µVrms dB ISC – – S RΘJC – – 4.5 5.5 – 2.0 – – 35 – – – – – 4.5 5.5 – 2.0 – – 35 – A mV °C/W NOTES: 1. Tlow to Thigh = 0° to +125°C 2. Although power dissipation is internally limited, specifications apply only for P ≤ Pmax = 25 W. 3. Load and line regulation are specified at constant junction temperature. Pulse testing is required with a pulse width ≤ 1.0 ms and a duty cycle ≤ 5%. 4. Without a heatsink, the thermal resistance (RθJA is 65°C/W). With a heatsink, the effective thermal resistance can approach the specified values of 2.0°C/W, depending on the efficiency of the heatsink. http://onsemi.com 2 LM323, LM323A Representative Schematic Diagram 1.0k Q1 Q8 300 Q4 Q5 Q3 10k Q10 520 Q12 2.6k Q6 Q7 Q11 6.0k 2.0k 3.9k Q13 Q14 6.0k Q17 40pF Q18 Q15 2.8k Gnd 1.7k 7.2k 3.0k 5.6k Q16 1.0k Q2 Q20 Q22 6.7V 1.0k Q19 10pF Q23 300 13 50 200 840 Output 0.12 2 210 16k Q24 Q21 100 200 Q25 Q27 Q26 Input Q9 VOLTAGE REGULATOR PERFORMANCE The performance of a voltage regulator is specified by its immunity to changes in load, input voltage, power dissipation, and temperature. Line and load regulation are tested with a pulse of short duration (< 100 µs) and are strictly a function of electrical gain. However, pulse widths of longer duration (> 1.0 ms) are sufficient to affect temperature gradients across the die. These temperature gradients can cause a change in the output voltage, in addition to changes by line and load regulation. Longer pulse widths and thermal gradients make it desirable to specify thermal regulation. Thermal regulation is defined as the change in output voltage caused by a change in dissipated power for a specified time, and is expressed as a percentage output ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) (2.0 mV/DIV) 2 voltage change per watt. The change in dissipated power can be caused by a change in either input voltage or the load current. Thermal regulation is a function of IC layout and die attach techniques, and usually occurs within 10 ms of a change in power dissipation. After 10 ms, additional changes in the output voltage are due to the temperature coefficient of the device. Figure 1 shows the line and thermal regulation response of a typical LM323A to a 20 W input pulse. The variation of the output voltage due to line regulation is labeled À and the thermal regulation component is labeled Á. Figure 2 shows the load and thermal regulation response of a typical LM323A to a 20 W load pulse. The output voltage variation due to load regulation is labeled À and the thermal regulation component is labeled Á. ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) (2.0 mV/DIV) 2 2 1 18 V 1 2 2.0 0 Vin , INPUT VOLTAGE (V) 8.0 V t, TIME (2.0 ms/DIV) Vout = 5.0 V Vin = 8.0 V → 18 V → 8.0 V Iout = 2.0 A 1 = Regline = 2.4 mV 2 = Regtherm = 0.0015% VO/W Iout , OUTPUT CURRENT (A) t, TIME (2.0 ms/DIV) Vout = 5.0 V Vin = 15 V Iout = 0 A → 2.0 A → 0 A 1 = Regline = 5.4 mV 2 = Regtherm = 0.0015% VO/W Figure 1. Line and Thermal Regulation Figure 2. Load and Thermal Regulation http://onsemi.com 3 LM323, LM323A 5.1 Vout , OUTPUT VOLTAGE (Vdc) Vin = 10 V Iout = 100 mA 5.0 Z O , OUTPUT IMPEDANCE ( Ω ) 10 10-1 Vin = 7.5 V Iout = 1.0 A CO = 0 TJ = 25°C 10-2 10-3 4.9 -90 -50 -10 30 70 110 TJ, JUNCTION TEMPERATURE (°C) 150 190 10-4 1.0 10 100 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M 100 M Figure 3. Temperature Stability Figure 4. Output Impedance 100 RR, RIPPLE REJECTION (dB) RR, RIPPLE REJECTION (dB) Iout = 50 mA 80 Iout = 3.0 A Vin = 10 V CO = 0 TJ = 25°C 100 80 60 60 40 Vin = 10 V CO = 0 f = 120 Hz TJ = 25°C 40 30 0.01 0.1 1.0 Iout, OUTPUT CURRENT (A) 10 20 1.0 10 100 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M 100 M Figure 5. Ripple Rejection versus Frequency Figure 6. Ripple Rejection versus Output Current 4.0 IB , QUIESCENT CURRENT (mA) IB , QUIESCENT CURRENT (mA) TJ = 55°C TJ = 25°C TJ = 150°C 5.0 4.0 3.0 2.0 1.0 0 0.01 TJ = 150°C TJ = -55°C TJ = 25°C 3.0 2.0 TJ = 150°C Iout = 2.0 A 1.0 TJ = 55°C TJ = 25°C 0 0 5.0 10 15 Vin, INPUT VOLTAGE (Vdc) 20 Vin = 10 V 0.1 1.0 Iout, OUTPUT CURRENT (A) 10 Figure 7. Quiescent Current versus Input Voltage Figure 8. Quiescent Current versus Output Current http://onsemi.com 4 LM323, LM323A 2.5 Iout = 3.0 A ISC , SHORT CIRCUIT CURRENT AT ZERO VOLTS (A) V in -Vout , INPUT TO OUTPUT VOLTAGE DIFFERENTIAL (Vdc) 8.0 2.0 6.0 TJ = 0°C TJ = 25°C TJ = 125°C 1.5 Iout = 0.5 A ∆Vout = 50 mV -50 Iout = 1.0 A 4.0 1.0 2.0 0.5 -90 -10 30 70 110 TJ, JUNCTION TEMPERATURE (°C) 150 190 0 5.0 10 15 Vin, INPUT VOLTAGE (Vdc) 20 25 Figure 9. Dropout Voltage Figure 10. Short Circuit Current ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 1.0 0.5 0 0 10 20 t, TIME (µs) ∆ Vout , OUTPUT VOLTAGE DEVIATION (V) Iout = 150 mA CO = 0 TJ = 25°C 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 1.5 1.0 0.5 0 0 10 20 t, TIME (µs) 30 40 Vin = 10 V CO = 0 TJ = 25°C ∆ Vin , INPUT VOLTAGE CHANGE (V) 30 40 Figure 11. Line Transient Response Iout , OUTPUT CURRENT (A) Figure 12. Load Transient Response APPLICATIONS INFORMATION Design Considerations The LM323,A series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition, Internal Short Circuit Protection that limits the maximum current the circuit will pass, and Output Transistor Safe–Area Compensation that reduces the output short circuit current as the voltage across the pass transistor is increased. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. An input bypass capacitor should be selected to provide good high–frequency characteristics to insure stable operation under all load conditions. A 0.33 µF or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulator’s input terminals. Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. http://onsemi.com 5 LM323, LM323A Input 0.33µF IO LM323, A R Constant Current to Grounded Load Input Output LM323, A 7 0.33µF 6 MC1741 + 2 3 0.1µF 10k The LM323,A regulator can also be used as a current source when connected as above. Resistor R determines the current as follows: IO = 5.0 V + IB R ∆IB ^ 0.7 mA over line, load and temperature changes IB ^ 3.5 mA For example, a 2.0 A current source would require R to be a 2.5 Ω, 15 W resistor and the output voltage compliance would be the input voltage less 7.5 V. 1.0k 4 VO, 8.0 V to 20 V Vin - VO ≥ 2.5 V The addition of an operational amplifier allows adjustment to higher or intermediate values while retaining regulation characteristics. The minimum voltage obtainable with this arrangement is 3.0 V greater than the regulator voltage. Figure 13. Current Regulator Figure 14. Adjustable Output Regulator 2N4398 or Equiv Input Rsc 2N4398 or Equiv. R LM323, A Output R MJ2955 or Equiv. LM323, A 1.0µF Output 1.0µF 0.1µF The LM323, A series can be current boosted with a PNP transistor. The 2N4398 provides current to 15 A. Resistor R in conjunction with the VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof. Input-output differential voltage minimum is increased by the VBE of the pass transistor. The circuit of Figure 16 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor. The current sensing PNP must be able to handle the short circuit current of the three-terminal regulator. Therefore, an 8.0 A power transistor is specified. Figure 15. Current Boost Regulator Figure 16. Current Boost with Short Circuit Protection http://onsemi.com 6 LM323, LM323A PACKAGE DIMENSIONS T SUFFIX PLASTIC PACKAGE CASE 221A–09 ISSUE AA NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM A B C D F G H J K L N Q R S T U V Z INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ----0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ----2.04 –T– B 4 SEATING PLANE F T S C Q 123 A U K H Z L V G D N R J http://onsemi.com 7 LM323, LM323A ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800–282–9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 LM323/D