0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
MC100EP91MNG

MC100EP91MNG

  • 厂商:

    ONSEMI(安森美)

  • 封装:

    QFN24_EP

  • 描述:

    TRANSLATOR NECL OUTPUT 24-QFN

  • 数据手册
  • 价格&库存
MC100EP91MNG 数据手册
2.5 V/3.3 V Any Level Positive Input to -3.3 V/-5.5 V NECL Output Translator MC100EP91 www.onsemi.com Description The MC100EP91 is a triple any level positive input to NECL output translator. The device accepts LVPECL, LVTTL, LVCMOS, HSTL, CML or LVDS signals, and translates them to differential NECL output signals (−3.0 V/−5.5 V). To accomplish the level translation the EP91 requires three power rails. The VCC pins should be connected to the positive power supply, and the VEE pin should be connected to the negative power supply. The GND pins are connected to the system ground plane. Both VEE and VCC should be bypassed to ground via 0.01 mF capacitors. Under open input conditions, the D input will be biased at VCC/2 and the D input will be pulled to GND. These conditions will force the Q outputs to a low state, and Q outputs to a high state, which will ensure stability. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. Features • • • • • • Maximum Input Clock Frequency = > 2.0 GHz Typical Maximum Input Data Rate = > 2.0 Gb/s Typical 500 ps Typical Propagation Delay Operating Range: VCC = 2.375 V to 3.8 V; VEE = −3.0 V to −5.5 V; GND = 0 V Q Output will Default LOW with Inputs Open or at GND These Devices are Pb-Free, Halogen Free and are RoHS Compliant 20 24 1 SOIC−20 WB DW SUFFIX CASE 751D 1 QFN−24 MN SUFFIX CASE 485L MARKING DIAGRAMS* 24 20 1 MC100EP91 AWLYYWWG 100 EP91 ALYWG G SOIC−20 WB QFN−24 1 A WL, L YY, Y WW, W G or G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION Device Package Shipping† MC100EP91DWG SOIC−20 WB (Pb-Free) 38 Units / Tube MC100EP91DWR2G SOIC−20 WB (Pb-Free) 1000 Tape & Reel QFN−24 (Pb-Free) 92 Units / Tube MC100EP91MNG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2016 March, 2021 − Rev. 7 1 Publication Order Number: MC100EP91/D MC100EP91 Positive Level Input D0 R1 D0 R1 D1 R1 D1 R1 NECL Output Q0 R2 Q0 Q1 R2 Q1 VCC VBB GND D2 R1 D2 R1 Q2 R2 VEE Q2 Figure 1. Logic Diagram Table 1. PIN DESCRIPTION Pin SOIC QFN Name I/O Default State 1, 20 3, 4, 12 VCC − − Positive Supply Voltage. All VCC Pins must be Externally Connected to Power Supply to Guarantee Proper Operation 10 15, 16 VEE − − Negative Supply Voltage. All VEE Pins must be Externally Connected to Power Supply to Guarantee Proper Operation 14, 17 19, 20, 23, 24 GND − − Ground 4, 7 7, 11 VBB − − ECL Reference Voltage Output 2, 5, 8 5, 8, 13 D[0:2] LVPECL, LVDS, LVTTL, LVCMOS, CML, HSTL Input Low Noninverted Differential Inputs [0:2]. Internal 75 kW to GND. 3, 6, 9 6, 9, 14 D[0:2] LVPECL, LVDS, LVTTL,LVCMOS, CML, HSTL Input High Inverted Differential Inputs [0:2]. Internal 75 kW to GND and 75 kW to VCC. When Inputs are Left Open They Default to (VCC − GND) / 2 19,16,13 2, 22, 18 Q[0:2] NECL Output − Noninverted Differential Outputs [0:2]. Typically Terminated with 50 W to VTT = VCC − 2 V 18,15,12 1, 21, 17 Q[0:2] NECL Output − Inverted Differential Outputs [0:2]. Typically Terminated with 50 W to VTT = VCC − 2 V 11 10 NC − − No Connect. The NC Pin is NOT Electrically Connected to the Die and may Safely be Connected to Any Voltage from VEE to VCC N/A − EP − Description Exposed Pad (Note 1) 1. The thermally conductive exposed pad on the package bottom (see case drawing) must be attached to a heat−sinking conduit and may only be electrically connected to VEE (not GND). www.onsemi.com 2 MC100EP91 GND GND Q1 24 VCC Q0 Q0 GND Q1 Q1 GND Q2 Q2 NC 20 18 12 19 17 16 15 14 13 11 MC100EP91 1 2 3 4 VCC D0 D0 VBB D1 5 6 7 8 D1 VBB D2 9 10 D2 VEE 23 22 Q1 GND GND 21 20 Exposed Pad (EP) 19 Q0 1 18 Q2 Q0 2 17 Q2 VCC 3 16 VEE VCC 4 15 VEE D0 5 14 D2 D0 6 13 D2 MC100EP91 7 VBB Figure 2. SOIC−20 Lead Pinout (Top View) 8 9 D1 D1 10 11 NC VBB 12 VCC Figure 3. QFN−24 Lead Pinout (Top View)* *All VCC, VEE and GND pins must be externally connected to a power supply and the underside exposed pad must be attached to an adequate heat−sinking conduit to guarantee proper operation. Table 2. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor (R1) 75 kW Internal Input Pullup Resistor (R2) 75 kW ESD Protection Human Body Model Machine Model Charged Device Model > 2 kV > 150 V > 2 kV Moisture Sensitivity (Note 1) Pb-Free Pkg SOIC−20 WB QFN−24 Level 3 Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in Transistor Count 446 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. www.onsemi.com 3 MC100EP91 Table 3. MAXIMUM RATINGS Symbol Rating Unit VCC Positive Power Supply GND = 0 V 3.8 to 0 V VEE Negative Power Supply GND = 0 V −6 V Positive Input Voltage GND = 0 V VI ≤ VCC 3.8 to 0 V VOP Operating Voltage GND = 0 V VCC − VEE 9.8 V Iout Output Current Continuous Surge 50 100 mA IBB PECL VBB Sink/Source ±0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction-to-Ambient) JESD 51−3 (1S-Single Layer Test Board) 0 lfpm 500 lfpm SOIC−20 WB SOIC−20 WB 90 60 °C/W qJA Thermal Resistance (Junction-to-Ambient) JESD 51−6 (2S2P Multilayer Test Board) with Filled Thermal Vias 0 lfpm 500 lfpm QFN−24 QFN−24 37 32 °C/W qJC Thermal Resistance (Junction-to-Case) Standard Board SOIC−20 WB QFN−24 30 to 35 11 °C/W Tsol Wave Solder (Pb-Free) 225 °C VI Parameter Condition 1 Condition 2 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Table 4. DC CHARACTERISTICS POSITIVE INPUTS (VCC = 2.5 V, VEE = −3.0 V to −5.5 V, GND = 0 V (Note 1)) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 10 14 20 10 14 20 10 14 20 mA ICC Positive Power Supply Current VIH Input HIGH Voltage (Single-Ended) 1335 VCC 1335 VCC 1335 VCC mV VIL Input LOW Voltage (Single-Ended) GND 875 GND 875 GND 875 mV 0 2.5 0 2.5 0 2.5 V 150 mA VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 2) IIH Input HIGH Current (@ VIH) IIL Input LOW Current (@ VIL) D D 150 0.5 −150 150 0.5 −150 0.5 −150 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. 1. Input parameters vary 1:1 with VCC. VCC can vary +1.3 V / −0.125 V. 2. VIHCMR min varies 1:1 with GND. VIHCMR max varies 1:1 with VCC. www.onsemi.com 4 MC100EP91 Table 5. DC CHARACTERISTICS POSITIVE INPUT (VCC = 3.3 V; VEE = −3.0 V to −5.5 V; GND = 0 V (Note 1)) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 10 16 24 10 16 24 10 16 24 mA ICC Positive Power Supply Current VIH Input HIGH Voltage (Single-Ended) 2135 VCC 2135 VCC 2135 VCC mV VIL Input LOW Voltage (Single-Ended) GND 1675 GND 1675 GND 1675 mV VBB PECL Output Voltage Reference 1775 1975 1775 1975 1775 1975 mV 3.3 0 3.3 0 3.3 V 150 mA VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 2) IIH Input HIGH Current (@ VIH) IIL Input LOW Current (@ VIL) D D 1875 0 1875 150 0.5 −150 1875 150 0.5 −150 mA 0.5 −150 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. 1. Input parameters vary 1:1 with VCC. VCC can vary +0.5 / −0.925 V. 2. VIHCMR min varies 1:1 with GND. VIHCMR max varies 1:1 with VCC. Table 6. DC CHARACTERISTICS NECL OUTPUT (VCC = 2.375 V to 3.8 V; VEE = −3.0 V to −5.5 V; GND = 0 V (Note 1)) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 40 50 60 38 50 68 38 50 68 mA IEE Negative Power Supply Current VOH Output HIGH Voltage (Note 2) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV VOL Output LOW Voltage (Note 2) −1945 −1770 −1600 −1945 −1770 −1600 −1945 −1770 −1600 mV NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. 1. Output parameters vary 1:1 with GND. 2. All loading with 50 W resistor to GND − 2.0 V. www.onsemi.com 5 MC100EP91 Table 7. AC CHARACTERISTICS (VCC = 2.375 V to 3.8 V; VEE = −3.0 V to −5.5 V; GND = 0 V) −40°C Symbol VOUTPP 25°C Min Typ fin ≤ 1.0 GHz fin ≤ 1.5 GHz fin ≤ 2.0 GHz 575 525 300 800 750 600 Differential Single-Ended 375 300 500 450 600 650 15 25 50 Characteristic Output Voltage Amplitude (Figure 4) (Note 1) tPLH tPHL0 Propagation Delay D to Q tSKEW Pulse Skew (Note 2) Output-to-Output (Note 3) Part-to-Part (Diff) (Note 3) tJITTER RMS Random Clock Jitter (Note 4) Peak-to-Peak Data Dependant Jitter (Note 5) VINPP Input Voltage Swing (Differential Configuration) (Note 6) tr, tf Output Rise/Fall Times @ 50 MHz (20%−80%) Q, Q 85°C Min Typ 600 525 250 800 750 550 375 300 500 450 600 675 75 95 125 15 30 50 0.5 20 2.0 200 800 1200 75 150 250 fin = 2.0 GHz fin = 2.0 Gb/s Max Max Min Typ Max 550 400 150 800 750 500 400 300 550 500 650 750 ps 75 105 125 15 30 70 80 105 150 ps 0.5 20 2.0 0.5 20 2.0 ps 200 800 1200 200 800 1200 mV 75 150 250 75 150 275 Unit mV ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. 1. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to GND − 2.0 V. Input edge rates 150 ps (20% − 80%). 2. Pulse Skew = |tPLH − tPHL| 3. Skews are valid across specified voltage range, part-to-part skew is for a given temperature. 4. RMS Jitter with 50% Duty Cycle Input Clock Signal. 5. Peak-to-Peak Jitter with input NRZ PRBS 231−1 at 2.0 Gb/s. 6. Input voltage swing is a Single-Ended measurement operating in differential mode. The device has a DC gain of ≈ 50. 10 9.0 750 8.0 AMP 7.0 650 6.0 5.0 550 4.0 450 3.0 2.0 350 1.0 RMS JITTER 250 RMS JITTER (ps) OUTPUT VOLTAGE AMPLITUDE (mV) 850 0.5 1.0 1.5 2.0 0 2.5 INPUT FREQUENCY (GHz) Figure 4. Output Voltage Amplitude (VOUTPP) / RMS Jitter vs. Input Frequency (fin) at Ambient Temperature (Typical) D VINPP = VIH(D) − VIL(D) D Q VOUTPP = VOH(Q) − VOL(Q) Q tPHL tPLH Figure 5. AC Reference Measurement www.onsemi.com 6 MC100EP91 Application Information and the maximum input swing of 3.0 V. Within these conditions, the input voltage can range from VCC to GND. Examples interfaces are illustrated below in a 50 W environment (Z = 50 W). All MC100EP91 inputs can accept LVPECL, LVTTL, LVCMOS, HSTL, CML, or LVDS signal levels. The limitations for differential input signal (LVDS, HSTL, LVPECL, or CML) are the minimum input swing of 150 mV VCC Z VCC EP91 LVDS Driver VCC Z D LVPECL Driver Z D Z D 50 W GND VTT = VCC − 2.0 V VEE GND Figure 6. Standard LVPECL Interface VCC GND VCC Z Z D EP91 Z VCC VCC 50 W HSTL Driver VEE Figure 7. Standard LVDS Interface VCC 50 W D CML Driver EP91 D Z D 50 W EP91 100 W D 50 W GND VCC 50 W GND GND VEE GND GND VEE GND Figure 8. Standard HSTL Interface VCC Z VCC VCC EP91 LVCMOS Driver D LVTTL Driver 1.5 V Figure 9. Standard 50 W Load CML Interface VCC Z D D EP91 Open D (externally generated reference voltage) GND GND VEE GND Figure 10. Standard LVTTL Interface GND VEE Figure 11. Standard LVCMOS Interface (D will default to VCC/2 when left open. A reference voltage of VCC/2 should be applied to D input, if D is interfaced to CMOS signals) www.onsemi.com 7 MC100EP91 Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = GND − 2.0 V Figure 12. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices) Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. www.onsemi.com 8 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS QFN24, 4x4, 0.5P CASE 485L ISSUE B 1 24 SCALE 2:1 D PIN 1 REFEENCE 2X 0.15 C 2X ÉÉÉ ÉÉÉ ÉÉÉ 0.15 C DETAIL A E ALTERNATE CONSTRUCTIONS ÉÉÉ ÉÉÉ ÇÇÇ EXPOSED Cu DETAIL B 0.10 C SEATING PLANE L 24X 7 DIM A A1 A3 b D D2 E E2 e L L1 MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 4.00 BSC 2.70 2.90 4.00 BSC 2.70 2.90 0.50 BSC 0.30 0.50 0.05 0.15 XXXXX XXXXX ALYWG G 13 E2 1 24 A1 A3 GENERIC MARKING DIAGRAM* D2 DETAIL A ÉÉ ÉÉ ÇÇ ALTERNATE TERMINAL CONSTRUCTIONS C A1 SIDE VIEW MOLD CMPD DETAIL B A A3 NOTE 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM THE TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. L1 TOP VIEW 0.08 C L L A B DATE 05 JUN 2012 19 e e/2 24X b 0.10 C A B 0.05 C BOTTOM VIEW NOTE 3 RECOMMENDED SOLDERING FOOTPRINT 4.30 24X 0.55 2.90 XXXXX = Specific Device Code A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. 1 4.30 2.90 0.50 PITCH 24X 0.32 DIMENSIONS: MILLIMETERS DOCUMENT NUMBER: DESCRIPTION: 98AON11783D QFN24, 4X4, 0.5P Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC−20 WB CASE 751D−05 ISSUE H DATE 22 APR 2015 SCALE 1:1 A 20 q X 45 _ M E h 0.25 H NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 B M D 1 10 20X B b 0.25 M T A S B DIM A A1 b c D E e H h L q S L A 18X e SEATING PLANE A1 c T GENERIC MARKING DIAGRAM* RECOMMENDED SOLDERING FOOTPRINT* 20 20X 20X 1.30 0.52 20 XXXXXXXXXXX XXXXXXXXXXX AWLYYWWG 11 1 11.00 1 XXXXX A WL YY WW G 10 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ 98ASB42343B SOIC−20 WB = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative
MC100EP91MNG 价格&库存

很抱歉,暂时无法提供与“MC100EP91MNG”相匹配的价格&库存,您可以联系我们找货

免费人工找货