MC74VHC1GT04DFT2

MC74VHC1GT04 Inverting Buffer / CMOS Logic Level Shifter LSTTL−Compatible Inputs Features • • • • • • • • • High Speed: tPD = 3.8 ns (Typ) at VCC = 5 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C http://onsemi.com MARKING DIAGRAMS 5 SC−88A DF SUFFIX CASE 419A 5 1 VK M G G M The MC74VHC1GT04 is a single gate inverting buffer fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky TTL while maintaining CMOS low power dissipation. The internal circuit is composed of three stages, including a buffer output which provides high noise immunity and stable output. The device input is compatible with TTL−type input thresholds and the output has a full 5 V CMOS level output swing. The input protection circuitry on this device allows overvoltage tolerance on the input, allowing the device to be used as a logic−level translator from 3 V CMOS logic to 5 V CMOS Logic or from 1.8 V CMOS logic to 3 V CMOS Logic while operating at the high−voltage power supply. The MC74VHC1GT04 input structure provides protection when voltages up to 7.0 V are applied, regardless of the supply voltage. This allows the MC74VHC1GT04 to be used to interface 5 V circuits to 3 V circuits. The output structures also provide protection when VCC = 0 V. These input and output structures help prevent device destruction caused by supply voltage − input/output voltage mismatch, battery backup, hot insertion, etc. 1 5 TSOP−5 DT SUFFIX CASE 483 5 1 VK M G G 1 VK = Device Code M = Date Code* G = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. TTL−Compatible Inputs: VIL = 0.8 V; VIH = 2 V CMOS−Compatible Outputs: VOH > 0.8 VCC; VOL < 0.1 VCC @ Load PIN ASSIGNMENT Power Down Protection Provided on Inputs and Outputs 1 Balanced Propagation Delays 2 IN A Pin and Function Compatible with Other Standard Logic Families 3 GND Chip Complexity: FETs = 105; Equivalent Gates = 26 Pb−Free Packages are Available 4 OUT Y 5 VCC NC FUNCTION TABLE NC 1 IN A 2 GND 3 5 4 VCC A Input Y Output L H H L OUT Y Figure 1. Pinout (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. IN A 1 OUT Y Figure 2. Logic Symbol © Semiconductor Components Industries, LLC, 2007 February, 2007 − Rev. 14 1 Publication Order Number: MC74VHC1GT04/D MC74VHC1GT04 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage Characteristics −0.5 to +7.0 V VIN DC Input Voltage −0.5 to +7.0 V −0.5 to 7.0 −0.5 to VCC + 0.5 V −20 mA +20 mA VOUT DC Output Voltage VCC = 0 High or Low State IIK Input Diode Current IOK Output Diode Current IOUT DC Output Current, per Pin +25 mA ICC DC Supply Current, VCC and GND +50 mA VOUT < GND; VOUT > VCC PD Power dissipation in still air qJA Thermal resistance TL Lead temperature, 1 mm from case for 10 s TJ Junction temperature under bias Tstg Storage temperature VESD ESD Withstand Voltage ILatchup Latchup Performance SC−88A, TSOP−5 200 mW SC−88A, TSOP−5 333 _C/W 260 °C +150 °C −65 to +150 °C > 2000 > 400 N/A V ±500 mA Human Body Model (Note 1) Machine Model (Note 2) Charged Device Model (Note 3) Above VCC and Below GND at 125°C (Note 4) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Tested to EIA/JESD22−A114−A 2. Tested to EIA/JESD22−A115−A 3. Tested to JESD22−C101−A 4. Tested to EIA/JESD78 RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit VCC DC Supply Voltage 3.0 5.5 V VIN DC Input Voltage 0.0 5.5 V 0.0 0.0 5.5 VCC V −55 +125 °C 0 0 100 20 ns/V VOUT DC Output Voltage TA VCC = 0 High or Low State Operating Temperature Range tr , tf VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V Input Rise and Fall Time 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80° C 117.8 TJ = 90 ° C 1,032,200 TJ = 100° C 80 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 110° C Time, Years TJ = 120° C Time, Hours TJ = 130° C Junction Temperature °C NORMALIZED FAILURE RATE DEVICE JUNCTION TEMPERATURE VERSUS TIME TO 0.1% BOND FAILURES 1 1 10 TIME, YEARS 100 1000 Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 2 MC74VHC1GT04 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Test Conditions Min 1.4 2.0 2.0 VIH Minimum High−Level Input Voltage 3.0 4.5 5.5 VIL Maximum Low−Level Input Voltage 3.0 4.5 5.5 VOH Minimum High−Level Output Voltage VIN = VIH or VIL VOL Maximum Low−Level Output Voltage VIN = VIH or VIL TA ≤ 85°C TA = 25°C VCC (V) Typ Max Min 1.4 2.0 2.0 0.53 0.8 0.8 VIN = VIH or VIL IOH = −50 mA 3.0 4.5 2.9 4.4 VIN = VIH or VIL IOH = −4 mA IOH = −8 mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50 mA 3.0 4.5 VIN = VIH or VIL IOL = 4.0 mA IOL = 8.0 mA Max 3.0 4.5 −55 ≤ TA ≤ 125°C Min Max 1.4 2.0 2.0 0.53 0.8 0.8 V 0.53 0.8 0.8 2.9 4.4 2.9 4.4 2.48 3.80 2.34 3.66 Unit V V V 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V V IIN Maximum Input Leakage Current VIN = 5.5 V or GND 0 to 5.5 ±0.1 ±1.0 ±1.0 mA ICC Maximum Quiescent Supply Current VIN = VCC or GND 5.5 1.0 20 40 mA ICCT Quiescent Supply Current Input: VIN = 3.4 V 5.5 1.35 1.50 1.65 mA IOPD Output Leakage Current VOUT = 5.5 V 0.0 0.5 5.0 10 mA ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎ AC ELECTRICAL CHARACTERISTICS Cload = 50 pF, Input tr = tf = 3.0 ns TA ≤ 85°C TA = 25°C Symbol tPLH, tPHL CIN Parameter Maximum Propagation Delay, Input A to Y Min Typ Max VCC = 3.3 ± 0.3 V CL = 15 pF CL = 50 pF 5.0 6.2 10.0 13.5 VCC = 5.0 ± 0.5 V CL = 15 pF CL = 50 pF 3.8 4.2 5.0 Test Conditions Maximum Input Capacitance Min Max −55 ≤ TA ≤ 125°C Min Max Unit 11.0 15.0 13.0 17.5 ns 6.7 7.7 7.5 8.5 8.5 9.5 10 10 10 pF Typical @ 25°C, VCC = 5.0 V CPD 10 Power Dissipation Capacitance (Note 5) pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD  VCC  fin + ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD  VCC2  fin + ICC  VCC. http://onsemi.com 3 MC74VHC1GT04 3.0 V A 50% GND tPLH tPHL VOH Y 50% VCC VOL Figure 4. Switching Waveforms TEST POINT OUTPUT DEVICE UNDER TEST CL* *Includes all probe and jig capacitance Figure 5. Test Circuit ORDERING INFORMATION Device Package Type MC74VHC1GT04DFT1 SC−88A M74VHC1GT04DFT1G SC−88A (Pb−Free) MC74VHC1GT04DFT2 SC−88A M74VHC1GT04DFT2G SC−88A (Pb−Free) MC74VHC1GT04DTT1 TSOP−5 M74VHC1GT04DTT1G TSOP−5 (Pb−Free) Package† 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 MC74VHC1GT04 PACKAGE DIMENSIONS SC−88A / SOT−353 / SC−70 CASE 419A−02 ISSUE J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. A G 5 4 −B− S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) M B M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC −−− 0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 J C K H SOLDERING FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 5 mm Ǔ ǒinches MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC −−− 0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 MC74VHC1GT04 PACKAGE DIMENSIONS TSOP−5 CASE 483−02 ISSUE F NOTE 5 2X 0.10 T 2X 0.20 T NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. D 5X 0.20 C A B 5 1 4 2 3 M B S K L DETAIL Z G A DIM A B C D G H J K L M S DETAIL Z J C 0.05 SEATING PLANE H T MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74VHC1GT04/D