MM74HC4040M

Revised December 2003 MM74HC4020 • MM74HC4040 14-Stage Binary Counter • 12-Stage Binary Counter General Description The MM74HC4020, MM74HC4040, are high speed binary ripple carry counters. These counters are implemented utilizing advanced silicon-gate CMOS technology to achieve speed performance similar to LS-TTL logic while retaining the low power and high noise immunity of CMOS. The MM74HC4020 is a 14 stage counter and the MM74HC4040 is a 12-stage counter. Both devices are incremented on the falling edge (negative transition) of the input clock, and all their outputs are reset to a low level by applying a logical high on their reset input. These devices are pin equivalent to the CD4020 and CD4040 respectively. All inputs are protected from damage due to static discharge by protection diodes to VCC and ground. Features ■ Typical propagation delay: 16 ns ■ Wide operating voltage range: 2–6V ■ Low input current: 1 µA maximum ■ Low quiescent current: 80 µA maximum (74HC Series) ■ Output drive capability: 10 LS-TTL loads Ordering Code: Order Number Package Number Package Description MM74HC4020M (Note 1) M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow MM74HC4020SJ M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MM74HC4020N N16E 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide MM74HC4040M (Note 1) M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow MM74HC4040SJ (Note 1) M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MM74HC4040MTC (Note 1) MM74HC4040N MTC16 N16E 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Note 1: Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Connection Diagrams MM74HC4040 MM74HC4020 © 2003 Fairchild Semiconductor Corporation DS005216 www.fairchildsemi.com MM74HC4020 • MM74HC4040 14-Stage Binary Counter • 12-Stage Binary Counter February 1984 MM74HC4020 • MM74HC4040 Logic Diagrams MM74HC4020 MM74HC4040 www.fairchildsemi.com 2 Recommended Operating Conditions (Note 3) −0.5 to +7.0V Supply Voltage (VCC ) DC Input Voltage (VIN) −1.5 to VCC +1.5V DC Output Voltage (VOUT) −0.5 to VCC +0.5V Clamp Diode Current (ICD) ±20 mA DC Output Current, per pin (IOUT) ±25 mA DC VCC or GND Current, per pin (ICC) ±50 mA Storage Temperature Range (TSTG) Min Max Supply Voltage (VCC) 2 6 V DC Input or Output Voltage 0 VCC V −40 +85 °C (tr, tf) VCC = 2.0V 1000 ns VCC = 4.5V 500 ns VCC = 6.0V 400 ns (VIN, VOUT) Operating Temperature Range (TA) Input Rise or Fall Times −65°C to +150°C Power Dissipation (PD) (Note 4) 600 mW S.O. Package only 500 mW Note 2: Maximum Ratings are those values beyond which damage to the device may occur. Lead Temperature (TL) DC Electrical Characteristics Symbol VIH VIL VOH Parameter Note 3: Unless otherwise specified all voltages are referenced to ground. 260°C (Soldering 10 seconds) Units Note 4: Power Dissipation temperature derating — plastic “N” package: − 12 mW/°C from 65°C to 85°C. (Note 5) Conditions VCC TA = 25°C Typ TA = −40 to 85°C TA = −55 to 125°C Guaranteed Limits Minimum HIGH Level Input 2.0V 1.5 1.5 1.5 Voltage 4.5V 3.15 3.15 3.15 6.0V 4.2 4.2 4.2 Maximum LOW Level Input 2.0V 0.5 0.5 0.5 Voltage 4.5V 1.35 1.35 1.35 6.0V 1.8 1.8 1.8 Minimum HIGH Level Output VIN = VIH or VIL Voltage |IOUT| ≤ 20 µA 2.0V 2.0 1.9 1.9 1.9 4.5V 4.5 4.4 4.4 4.4 6.0V 6.0 5.9 5.9 5.9 |IOUT| ≤ 4.0 mA 4.5V 4.2 3.98 3.84 3.7 |IOUT| ≤ 5.2 mA 6.0V 5.7 5.48 5.34 5.2 Units V V V VIN = VIH or VIL VOL Maximum LOW Level Output VIN = VIH or VIL Voltage |IOUT| ≤ 20 µA 2.0V 0 0.1 0.1 0.1 4.5V 0 0.1 0.1 0.1 6.0V 0 0.1 0.1 0.1 |IOUT| ≤ 4.0 mA 4.5V 0.2 .26 0.33 0.4 |IOUT| ≤ 5.2 mA 6.0V 0.2 .26 0.33 0.4 V VIN = VIH or VIL IIN Maximum Input Current VIN = VCC or GND 6.0V ±0.1 ±1.0 ±1.0 µA ICC Maximum Quiescent Supply VIN = VCC or GND 6.0V 8.0 80 160 µA Current IOUT = 0 µA Note 5: For a power supply of 5V ±10% the worst case output voltages (VOH, and VOL) occur for HC at 4.5V. Thus the 4.5V values should be used when designing with this supply. Worst case VIH and VIL occur at VCC = 5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current (IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0V values should be used. 3 www.fairchildsemi.com MM74HC4020 • MM74HC4040 Absolute Maximum Ratings(Note 2) MM74HC4020 • MM74HC4040 AC Electrical Characteristics VCC = 5V, TA = 25°C, CL = 15 pF, tr = tf = 6 ns Symbol Parameter Conditions fMAX Maximum Operating Frequency tPHL, tPLH Maximum Propagation Typ (Note 6) Guaranteed Limit Units 50 30 MHz 17 35 ns 16 40 ns 10 20 ns 10 16 ns Delay Clock to Q tPHL Maximum Propagation Delay Reset to any Q tREM Minimum Reset Removal Time tW Minimum Pulse Width Note 6: Typical Propagation delay time to any output can be calculated using: tP = 17 + 12(N–1) ns; where N is the number of the output, QW, at VCC = 5V. AC Electrical Characteristics VCC = 2.0V to 6.0V, CL = 50 pF, tr = tf = 6 ns (unless otherwise specified) Symbol fMAX tPHL, tPLH tPHL, tPLH tPHL tREM tW tTLH, tTHL tr, tf CPD Parameter Conditions TA = 25°C VCC Typ TA = −40 to 85°C TA = −55 to 125°C Guaranteed Limits Maximum Operating 2.0V 10 6 5 4 Frequency 4.5V 40 30 24 20 6.0V 50 35 28 24 Maximum Propagation 2.0V 80 210 265 313 Delay Clock to Q1 4.5V 21 42 53 63 6.0V 18 36 45 53 Maximum Propagation 2.0V 80 125 156 188 Delay Between Stages 4.5V 18 25 31 38 from Qn to Qn+1 6.0V 15 21 26 31 Maximum Propagation 2.0V 72 240 302 358 Delay Reset to any Q 4.5V 24 48 60 72 (4020 and 4040) 6.0V 20 41 51 61 Minimum Reset 2.0V 100 126 149 Removal Time 4.5V 20 25 50 6.0V 16 21 25 2.0V 90 100 120 4.5V 16 20 24 6.0V 14 18 20 Minimum Pulse Width Maximum 2.0V 30 75 95 110 Output Rise 4.5V 10 15 19 22 and Fall Time 6.0V 9 13 16 19 Maximum Input Rise and 1000 1000 1000 Fall Time 500 500 500 400 400 400 Power Dissipation (per package) 55 Units MHz ns ns ns ns ns ns ns pF Capacitance (Note 7) CIN Maximum Input 5 10 10 10 Capacitance Note 7: CPD determines the no load dynamic power consumption, PD = CPD VCC2 f + ICC VCC, and the no load dynamic current consumption, IS = CPD VCC f + ICC. www.fairchildsemi.com 4 pF MM74HC4020 • MM74HC4040 Timing Diagram 5 www.fairchildsemi.com MM74HC4020 • MM74HC4040 Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package Number M16A www.fairchildsemi.com 6 MM74HC4020 • MM74HC4040 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M16D 7 www.fairchildsemi.com MM74HC4020 • MM74HC4040 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC16 www.fairchildsemi.com 8 MM74HC4020 • MM74HC4040 14-Stage Binary Counter • 12-Stage Binary Counter Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Package Number N16E Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 9 www.fairchildsemi.com