NCV8506 Series
Micropower 400 mA LDO
Linear Regulators with
DELAY and RESET
The NCV8506 is a family of precision micropower voltage
regulators. Their output current capability is 400 mA. The family has
output voltage options for Adjustable, 2.5 V, 3.3 V and 5.0 V.
The output voltage is accurate within ± 2.0% with a maximum
dropout voltage of 0.6 V at 400 mA. Low quiescent current is a feature
drawing only 100 mA with a 100 mA load. This part is ideal for any and
all battery operated microprocessor equipment.
Microprocessor control logic includes an active RESET (with
DELAY).
The active RESET circuit operates correctly at an output voltage as
low as 1.0 V. The RESET function is activated during the power up
sequence or during normal operation if the output voltage drops below
the regulation limits.
The regulator is protected against reverse battery, short circuit, and
thermal overload conditions. The device can withstand load dump
transients making it suitable for use in automotive environments. The
device has also been optimized for EMC conditions.
Features
•
•
•
•
•
•
•
•
•
•
•
Output Voltage Options: Adjustable, 2.5 V, 3.3 V, 5.0 V
± 2.0% Output
Low 100 mA Quiescent Current
Fixed or Adjustable Output Voltage
Active RESET
400 mA Output Current Capability
Fault Protection
♦ +60 V Peak Transient Voltage
♦ −15 V Reverse Voltage
♦ Short Circuit
♦ Thermal Overload
NCV Prefix for Automotive and Other Applications Requiring Site
and Change Control
AEC Qualified
PPAP Capable
These are Pb−Free Devices
© Semiconductor Components Industries, LLC, 2009
October, 2009 − Rev. 11
1
http://onsemi.com
MARKING
DIAGRAM
1
D2PAK−7
DPS SUFFIX
CASE 936AB
NC
V8506x
AWLYWWG
1
x
= Voltage Ratings as Indicated Below:
A = Adjustable
2 = 2.5 V
3 = 3.3 V
5 = 5.0 V
A
= Assembly Location
WL = Wafer Lot
Y
= Year
WW = Work Week
G
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
Publication Order Number:
NCV8506/D
NCV8506 Series
PIN CONNECTIONS
ADJUSTABLE OUTPUT
FIXED OUTPUT
D2PAK−7
D2PAK−7
Tab = GND
Lead
1. DELAY
2. NC
3. RESET
4. GND
5. VADJ
6. VOUT
7. VIN
1
IQ
1
SENSE
(Fixed Output Only)
VIN
VOUT
VDD
33 mF
10 mF
NCV8506
DELAY
CDELAY
Microprocessor
VBAT
Tab = GND
Lead
1. DELAY
2. NC
3. RESET
4. GND
5. SENSE
6. VOUT
7. VIN
RRST
5.1 k
VADJ
(Adjustable
Output Only)
RESET
I/O
GND
Figure 1. Application Diagram
http://onsemi.com
2
NCV8506 Series
MAXIMUM RATINGS
Rating
Value
Unit
−15 to 45
V
Peak Transient Voltage (46 V Load Dump @ VIN = 14 V)
60
V
Operating Voltage
45
V
VOUT (DC)
−0.3 to 16
V
Voltage Range (RESET, DELAY)
−0.3 to 10
V
Input Voltage Range
VADJ
−0.3 to 16
V
4.0
200
kV
V
Junction Temperature, TJ
−40 to +150
°C
Storage Temperature, TS
−55 to 150
°C
2.0
10−50*
°C/W
°C/W
240 peak (Note 2)
°C
VIN (DC)
ESD Susceptibility
(Human Body Model)
(Machine Model)
Package Thermal Resistance, 7 Lead D2PAK
Junction−to−Case, RqJC
Junction−to−Ambient, RqJA
Lead Temperature Soldering:
Reflow: (SMD styles only) (Note 1)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. 60 second maximum above 183°C.
2. −5°C/+0°C allowable conditions.
*Depending on thermal properties of substrate, RqJA = RqJC + RqCA.
ELECTRICAL CHARACTERISTICS (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 150°C; VIN = dependent on voltage option (Note 3);
unless otherwise specified.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
Output Voltage for 2.5 V Option (VO)
6.5 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA
4.5 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA
2.450
2.425
2.5
2.5
2.550
2.575
V
V
Output Voltage for 3.3 V Option (VO)
7.3 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA
4.5 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA
3.234
3.201
3.3
3.3
3.366
3.399
V
V
Output Voltage for 5.0 V Option (VO)
9.0 V < VIN < 16 V, 1.0 mA ≤ IOUT ≤ 400 mA
6.0 V < VIN < 26 V, 1.0 mA ≤ IOUT ≤ 400 mA
4.90
4.85
5.0
5.0
5.10
5.15
V
V
Output Voltage for Adjustable Option (VO)
VOUT = VADJ (Unity Gain)
6.5 V < VIN < 16 V, 1.0 mA < IOUT < 400 mA
4.5 V < VIN < 26 V, 1.0 mA < IOUT < 400 mA
1.274
1.261
1.300
1.306
1.326
1.339
V
V
Dropout Voltage (VIN − VOUT)
(5.0 V and Adj. > 5.0 V Options Only)
IOUT = 400 mA
IOUT = 1.0 mA
−
−
400
30
600
150
mV
mV
Load Regulation
VIN = 14 V, 5.0 mA ≤ IOUT ≤ 400 mA
−30
5.0
30
mV
Line Regulation (2.5 V, 3.3 V, and
Adjustable Options)
4.5 V < VIN < 26 V, IOUT = 1.0 mA
−
5.0
25
mV
Line Regulation (5.0 V Option)
6.0 V < VIN < 26 V, IOUT = 1.0 mA
−
5.0
25
mV
Quiescent Current, (IQ) Active Mode
IOUT = 100 mA, VIN = 12 V, Delay = 3.0 V
IOUT = 75 mA, VIN = 14 V, Delay = 3.0 V
IOUT ≤ 400 mA, VIN = 14 V, Delay = 3.0 V
−
−
−
100
2.5
25
150
5.0
45
mA
mA
mA
425
800
−
mA
Output Stage
Current Limit
−
Short Circuit Output Current
VOUT = 0 V
100
500
−
mA
Thermal Shutdown
(Guaranteed by Design)
150
180
−
°C
3. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type.
http://onsemi.com
3
NCV8506 Series
ELECTRICAL CHARACTERISTICS (continued) (IOUT = 1.0 mA, −40°C ≤ TJ ≤ 150°C; VIN = dependent on voltage option (Note 4);
unless otherwise specified.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
2.35
2.30
25
−
−
−
1.0 × VO
−
−
V
V
mV
3.10
3.00
35
−
−
−
1.0 × VO
−
−
V
V
mV
4.70
4.60
50
−
−
−
1.0 × VO
−
−
V
V
mV
1.22
1.19
10
−
−
−
1.0 × VO
−
−
V
V
mV
−
0.1
0.4
V
Reset Function (RESET)
RESET Threshold for 2.5 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Threshold for 3.3 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Threshold for 5.0 V Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 6.0 V (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Threshold for Adjustable Option
HIGH (VRH)
LOW (VRL)
Hysteresis
VIN = 4.5 V (Note 5) (Note 6)
VOUT Increasing
VOUT Decreasing
RESET Output Voltage
Low (VRLO)
VIN = Minimum (Note 6) (Note 7)
1.0 V ≤ VOUT ≤ VRL, RRESET = 5.1 k
DELAY Switching Threshold (VDT)
(2.5 V, 3.3 V, and 5.0 V Options)
VIN = Minimum (Note 6) (Note 7)
1.4
1.8
2.2
V
DELAY Switching Threshold (VDT)
(Adjustable Option)
VIN = Minimum (Note 6) (Note 7)
1.0
1.3
1.6
V
DELAY Low Voltage
VIN = Minimum (Note 6) (Note 7)
VOUT < RESET Threshold Low(min)
−
−
0.2
V
DELAY Charge Current
VIN = Minimum (Note 6) (Note 7)
DELAY = 1.0 V, VOUT > VRH
2.5
4.0
5.5
mA
DELAY Discharge Current
VIN = Minimum (Note 6) (Note 7)
DELAY = 1.0 V, VOUT < VRL
5.0
−
−
mA
VADJ = 1.25 V
−0.5
−
0.5
mA
Voltage Adjust (Adjustable Output only)
Input Current
4. Voltage range specified in the Output Stage of the Electrical Characteristics in boldface type.
5. For VIN ≤ 4.5 V, a RESET = Low may occur with the output in regulation.
6. Part is guaranteed by design to meet specification over the entire VIN voltage range, but is production tested only at the specified VIN
voltage.
7. Minimum VIN = 4.5 V for 2.5 V, 3.3 V, and Adjustable options. Minimum VIN = 6.0 V for 5.0 V option.
http://onsemi.com
4
NCV8506 Series
PACKAGE PIN DESCRIPTION, ADJUSTABLE OUTPUT
Pin Number
Pin Symbol
Function
1
DELAY
2
NC
3
RESET
4
GND
Ground. All GND leads must be connected to Ground.
5
VADJ
Voltage Adjust. A resistor divider from VOUT to this lead sets the output voltage.
6
VOUT
±2.0%, 400 mA output.
7
VIN
Timing capacitor for RESET function.
No connection.
Active reset (accurate to VOUT ≥ 1.0 V)
Input Voltage.
PACKAGE PIN DESCRIPTION, FIXED OUTPUT
Pin Number
Pin Symbol
1
DELAY
2
NC
3
RESET
4
GND
5
SENSE
6
VOUT
7
VIN
Function
Timing capacitor for RESET function.
No connection.
Active reset (accurate to VOUT ≥ 1.0 V)
Ground. All GND leads must be connected to Ground.
Kelvin connection which allows remote sensing of output voltage for improved regulation. If
remote sensing is not desired, connect to VOUT.
±2.0%, 400 mA output.
Input Voltage.
http://onsemi.com
5
NCV8506 Series
VOUT
VIN
Current Source
(Circuit Bias)
SENSE
IBIAS
Current Limit
Sense
IBIAS
+ −
1.8 V (Fixed Versions)
1.3 V (Adjustable Version)
VBG
+
DELAY
VBG −18 mV Fixed Versions only
−
RESET
Error Amplifier
+
−
Thermal
Protection
4.0 mA
Bandgap
Reference
IBIAS
VBG
Figure 2. Block Diagram
http://onsemi.com
6
15 k
Adjustable
Version only
VADJ
GND
NCV8506 Series
TYPICAL PERFORMANCE CHARACTERISTICS
5.10
3.35
Vout, OUTPUT VOLTAGE (V)
5.08
5.06
Vout, OUTPUT VOLTAGE (V)
VOUT = 5.0 V
VIN = 14 V
IOUT = 5.0 mA
5.04
5.02
5.00
4.98
4.96
4.94
VOUT = 3.3 V
VIN = 14 V
IOUT = 5.0 mA
3.33
3.31
3.29
3.27
3.25
4.92
4.90
−40 −20
0
3.23
−40 −20
20 40
60 80 100 120 140 160
TEMPERATURE (°C)
Figure 3. 5 V Output Voltage vs Temperature
600
Vout, OUTPUT VOLTAGE (V)
2.53
DROPOUT VOLTAGE (mV)
VOUT = 2.5 V
VIN = 14 V
IOUT = 5.0 mA
2.54
2.52
2.51
2.50
2.49
2.48
2.47
2.46
125 °C
400
25 °C
300
200
−40 °C
100
0
0
20 40
60 80 100 120 140 160
TEMPERATURE (°C)
Figure 5. 2.5 V Output Voltage vs Temperature
100
0
50
100
2.5 V
10
Stable Region
CVOUT = 0.1 mF
1.0
Stable Region
Unstable Region
VIN = 14 V
CVOUT = 10 mF
50
400
CVOUT = 33 mF*
ESR (W)
1.0
0.1
350
Unstable Region
3.3 V
10
300
100 150
200
250
Iout, OUTPUT CURRENT (mA)
Figure 6. Dropout Voltage vs Output Current
5.0 V
Unstable Region
ESR (W)
500
5 V and Adj. > 5 V options only
2.45
−40 −20
0
20 40
60 80 100 120 140 160
TEMPERATURE (°C)
Figure 4. 3.3 V Output Voltage vs Temperature
2.55
0.01
0
300
100 150 200
250
Iout, OUTPUT CURRENT (mA)
350
0.1
400
Figure 7. Output Stability with Output Voltage Change
*There is no unstable lower
region for the 33 mF capacitor
0
50
5 V version
300
100 150 200
250
Iout, OUTPUT CURRENT (mA)
350
400
Figure 8. Output Stability with Output Capacitor Change
http://onsemi.com
7
NCV8506 Series
TYPICAL PERFORMANCE CHARACTERISTICS
1.8
+25°C
60
+125°C
1.6
IQ, QUIESCENT CURRENT (mA)
IQ, QUIESCENT CURRENT (mA)
2.0
−40°C
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
5
10
40
15 20
25 30 35
IOUT, OUTPUT CURRENT (mA)
45
Figure 9. Quiescent Current vs Output Current
Iout = 200 mA
8
6
Iout = 100 mA
Iout = 50 mA
2
Iout = 10 mA
0
6
8
10
12 14
16 18 20
VIN, INPUT VOLTAGE (V)
22
24
20
10
50
0
100 150 200 250 300 350 400 450 500
IOUT, OUTPUT CURRENT (mA)
140
T = 25°C
10
4
−40°C
30
Figure 10. Quiescent Current vs Output Current
IQ, QUIESCENT CURRENT (mA)
IQ, QUIESCENT CURRENT (mA)
12
+25°C
40
0
50
+125°C
50
Iout = 100 mA
100
80
60
40
20
0
26
T = 25°C
120
8
6
10
12 14
16 18 20
VIN, INPUT VOLTAGE (V)
22
24
26
Figure 12. Quiescent Current vs Input Voltage
Figure 11. Quiescent Current vs Input Voltage
http://onsemi.com
8
NCV8506 Series
CIRCUIT DESCRIPTION
REGULATOR CONTROL FUNCTIONS
The NCV8506 contains the microprocessor compatible
control function RESET (Figure 13).
The DELAY lead provides source current (typically 4.0 mA)
to the external DELAY capacitor during the following
proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
VIN
RESET
Threshold
VOUT
DELAY
Threshold
(VDT)
DELAY
RESET
Td
Voltage Adjust
Td
Figure 14 shows the device setup for a user configurable
output voltage. The feedback to the VADJ pin is taken from
a voltage divider referenced to the output voltage. The loop
is balanced around the Unity Gain threshold (1.30 V
typical).
Figure 13. Reset and Delay Circuit Wave Forms
RESET Function
A RESET signal (low voltage) is generated as the IC
powers up until VOUT is within 1.5% of the regulated output
voltage, or when VOUT drops out of regulation,and is lower
than 4.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
guaranteeing that the RESET signal is valid for VOUT as low
as 1.0 V.
≈5.0 V
VOUT
NCV8506
VADJ
15 k
COUT
1.28 V
5.1 k
DELAY Function
The reset delay circuit provides a programmable (by
external capacitor) delay on the RESET output lead.
Figure 14. Adjustable Output
Voltage
APPLICATION NOTES
STABILITY CONSIDERATIONS
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start−up
delay, load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
temperatures (−25°C to −40°C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturers data sheet usually provides this information.
SETTING THE DELAY TIME
The delay time is controlled by the Reset Delay Low
Voltage, Delay Switching Threshold, and the Delay Charge
Current. The delay follows the equation:
tDELAY +
ƪCDELAY(Vdt * Reset Delay Low Voltage)ƫ
Delay Charge Current
Example:
Using CDELAY = 33 nF.
Assume reset Delay Low Voltage = 0.
Use the typical value for Vdt = 1.8 V (2.5 V, 3.3 V, and
5.0 V options).
Use the typical value for Delay Charge Current = 4.2 mA.
tDELAY +
ƪ33 nF(1.8 * 0)ƫ
4.2 mA
+ 14 ms
http://onsemi.com
9
NCV8506 Series
The value for the output capacitor COUT shown in Figure 15
should work for most applications, however it is not
necessarily the optimized solution.
VIN
The value of RqJA can then be compared with those in the
package section of the data sheet. Those packages with
RqJA’s less than the calculated value in equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
VOUT
CIN*
0.1 mF
NCV8506
RRST
COUT**
33 mF
RESET
VIN
Figure 16. Single Output Regulator with Key
Performance Parameters Labeled
HEAT SINKS
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RqJA:
CALCULATING POWER DISSIPATION IN A
SINGLE OUTPUT LINEAR REGULATOR
The maximum power dissipation for a single output
regulator (Figure 16) is:
(1)
) VIN(max)IQ
Where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
Once the value of PD(max) is known, the maximum
permissible value of RqJA can be calculated:
150° C * TA
PD
VOUT
IQ
Figure 15. Test and Application Circuit Showing
Output Compensation
RqJA +
SMART
REGULATOR®
} Control
Features
*CIN required if regulator is located far from the power supply
filter.
**COUT required for stability. Capacitor must operate at minimum
temperature expected.
PD(max) + [VIN(max) * VOUT(min)] IOUT(max)
IOUT
IIN
RqJA + RqJC ) RqCS ) RqSA
(3)
Where:
RqJC = the junction−to−case thermal resistance,
RqCS = the case−to−heatsink thermal resistance, and
RqSA = the heatsink−to−ambient thermal resistance.
RqJC appears in the package section of the data sheet. Like
RqJA, it too is a function of package type. RqCS and RqSA are
functions of the package type, heatsink and the interface
between them. These values appear in heat sink data sheets
of heat sink manufacturers.
(2)
http://onsemi.com
10
NCV8506 Series
ORDERING INFORMATION
Device
Output Voltage
NCV8506D2TADJG
NCV8506D2TADJR4G
Adjustable
NCV8506D2T25G
NCV8506D2T25R4G
2.5 V
NCV8506D2T33G
NCV8506D2T33R4G
3.3 V
NCV8506D2T50G
NCV8506D2T50R4G
5.0 V
Package
Shipping†
D2PAK−7
(Pb−Free)
50 Units / Rail
D2PAK−7
(Pb−Free)
750 Tape & Reel
D2PAK−7
(Pb−Free)
50 Units / Rail
D2PAK−7
(Pb−Free)
750 Tape & Reel
D2PAK−7
(Pb−Free)
50 Units / Rail
D2PAK−7
(Pb−Free)
750 Tape & Reel
D2PAK−7
(Pb−Free)
50 Units / Rail
D2PAK−7
(Pb−Free)
750 Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLC).
http://onsemi.com
11
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
D2PAK−7 (SHORT LEAD)
CASE 936AB−01
ISSUE B
DATE 08 SEP 2009
A
1
SCALE 1:1
E
L1
B
A
0.10
A
E/2
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH AND GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.005 MAXIMUM PER SIDE. THESE DIMENSIONS
TO BE MEASURED AT DATUM H.
4. THERMAL PAD CONTOUR OPTIONAL WITHIN
DIMENSIONS E, L1, D1, AND E1. DIMENSIONS
D1 AND E1 ESTABLISH A MINIMUM MOUNTING
SURFACE FOR THE THERMAL PAD.
SEATING
PLANE
M
B A
M
E1
c2
D1
D
7X
H
DETAIL C
e
b
0.13
M
B A
VIEW A−A
c
A
M
B
H
SEATING
PLANE
A1
RECOMMENDED
SOLDERING FOOTPRINT*
L
0.424
INCHES
MIN
MAX
0.170
0.180
0.000
0.010
0.026
0.036
0.017
0.026
0.045
0.055
0.325
0.368
0.270
−−−
0.380
0.420
0.245
−−−
0.050 BSC
0.539
0.579
0.058
0.078
−−−
0.066
0.010 BSC
0°
8°
MILLIMETERS
MIN
MAX
4.32
4.57
0.00
0.25
0.66
0.91
0.43
0.66
1.14
1.40
8.25
9.53
6.86
−−−
9.65
10.67
6.22
−−−
1.27 BSC
13.69
14.71
1.47
1.98
−−−
1.68
0.25 BSC
0°
8°
GENERIC
MARKING DIAGRAM*
M
L3
DIM
A
A1
b
c
c2
D
D1
E
E1
e
H
L
L1
L3
M
GAUGE
PLANE
XX
XXXXXXXXX
AWLYWWG
DETAIL C
0.310
0.584
1
XXXXX
A
WL
Y
WW
G
0.136
7X
0.050
PITCH
0.040
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
DESCRIPTION:
98AON14119D
D2PAK−7 (SHORT LEAD)
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
工商网监
湘ICP备2023018690号
