NTD20N06L, NTDV20N06L
MOSFET – Power,
N-Channel, Logic Level,
DPAK/IPAK
20 A, 60 V
Designed for low voltage, high speed switching applications in
power supplies, converters and power motor controls and bridge
circuits.
Features
www.onsemi.com
V(BR)DSS
RDS(on) TYP
ID MAX
60 V
39 mW@5.0 V
20 A
(Note 1)
• AEC Q101 Qualified − NTDV20N06L
• These Devices are Pb−Free and are RoHS Compliant
D
Typical Applications
N−Channel
Power Supplies
Converters
Power Motor Controls
Bridge Circuits
G
S
4
MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)
Value
Unit
Drain−to−Source Voltage
VDSS
60
Vdc
Drain−to−Gate Voltage (RGS = 10 MW)
VDGR
60
Vdc
Gate−to−Source Voltage
− Continuous
− Non−repetitive (tpv10 ms)
Drain Current
− Continuous @ TA = 25°C
− Continuous @ TA = 100°C
− Single Pulse (tpv10 ms)
Total Power Dissipation @ TA = 25°C
Derate above 25°C
Total Power Dissipation @ TA = 25°C (Note 1)
Total Power Dissipation @ TA = 25°C (Note 2)
Operating and Storage Temperature Range
Single Pulse Drain−to−Source Avalanche
Energy − Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 5.0 Vdc,
L = 1.0 mH, IL(pk) = 16 A, VDS = 60 Vdc)
Thermal Resistance
− Junction−to−Case
− Junction−to−Ambient (Note 1)
− Junction−to−Ambient (Note 2)
Maximum Lead Temperature for Soldering
Purposes, 1/8 in from case for 10 seconds
Vdc
VGS
VGS
±15
±20
ID
ID
20
10
60
Adc
PD
60
0.40
1.88
1.36
W
W/°C
W
W
TJ, Tstg
−55 to
+175
°C
128
mJ
IDM
EAS
RqJC
RqJA
RqJA
2.5
80
110
TL
260
Apk
°C/W
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
1. When surface mounted to an FR4 board using 1 in pad size, (Cu Area 1.127 in2).
2. When surface mounted to an FR4 board using recommended pad size,
(Cu Area 0.412 in2).
© Semiconductor Components Industries, LLC, 2014
May, 2019 − Rev. 5
1
4
1 2
1
3
2
3
IPAK
CASE 369D
STYLE 2
DPAK
CASE 369C
STYLE 2
MARKING DIAGRAMS
& PIN ASSIGNMENTS
4
Drain
4
Drain
AYWW
20
N6LG
Symbol
Rating
AYWW
20
N6LG
•
•
•
•
2
1
3
Drain
Gate
Source
A
Y
WW
20N6L
G
1 2 3
Gate Drain Source
= Assembly Location*
= Year
= Work Week
= Device Code
= Pb−Free Package
* The Assembly Location code (A) is front side
optional. In cases where the Assembly Location is
stamped in the package, the front side assembly
code may be blank.
ORDERING INFORMATION
See detailed ordering and shipping information on page 2 of
this data sheet.
Publication Order Number:
NTD20N06L/D
NTD20N06L, NTDV20N06L
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Drain−to−Source Breakdown Voltage (Note 3)
(VGS = 0 Vdc, ID = 250 mAdc)
Temperature Coefficient (Positive)
V(BR)DSS
Unit
60
−
71.3
71.2
−
−
−
−
−
−
1.0
10
−
−
±100
1.0
−
1.6
4.6
2.0
−
−
39
48
−
−
0.81
0.72
1.66
−
gFS
−
17.5
−
mhos
pF
OFF CHARACTERISTICS
Zero Gate Voltage Drain Current
(VDS = 60 Vdc, VGS = 0 Vdc)
(VDS = 60 Vdc, VGS = 0 Vdc, TJ = 150°C)
IDSS
Gate−Body Leakage Current (VGS = ± 15 Vdc, VDS = 0 Vdc)
IGSS
Vdc
mV/°C
mAdc
nAdc
ON CHARACTERISTICS (Note 3)
Gate Threshold Voltage (Note 3)
(VDS = VGS, ID = 250 mAdc)
Threshold Temperature Coefficient (Negative)
VGS(th)
Static Drain−to−Source On−Resistance (Note 3)
(VGS = 5.0 Vdc, ID = 10 Adc)
RDS(on)
Static Drain−to−Source On−Resistance (Note 3)
(VGS = 5.0 Vdc, ID = 20 Adc)
(VGS = 5.0 Vdc, ID = 10 Adc, TJ = 150°C)
VDS(on)
Forward Transconductance (Note 3) (VDS = 4.0 Vdc, ID = 10 Adc)
Vdc
mV/°C
mW
Vdc
DYNAMIC CHARACTERISTICS
Input Capacitance
Output Capacitance
Transfer Capacitance
(VDS = 25 Vdc, VGS = 0 Vdc,
f = 1.0 MHz)
Ciss
−
707
990
Coss
−
224
320
Crss
−
72
105
td(on)
−
9.6
20
tr
−
98
200
td(off)
−
25
50
tf
−
62
120
QT
−
16.6
32
Q1
−
5.5
−
Q2
−
8.5
−
VSD
−
−
0.97
0.85
1.2
−
Vdc
trr
−
42
−
ns
ta
−
30
−
tb
−
12
−
QRR
−
0.066
−
SWITCHING CHARACTERISTICS (Note 4)
Turn−On Delay Time
Rise Time
Turn−Off Delay Time
(VDD = 30 Vdc, ID = 20 Adc,
VGS = 5.0 Vdc,
RG = 9.1 W) (Note 3)
Fall Time
Gate Charge
(VDS = 48 Vdc, ID = 20 Adc,
VGS = 5.0 Vdc) (Note 3)
ns
nC
SOURCE−DRAIN DIODE CHARACTERISTICS
Forward On−Voltage
Reverse Recovery Time
(IS = 20 Adc, VGS = 0 Vdc) (Note 3)
(IS = 20 Adc, VGS = 0 Vdc, TJ = 150°C)
(IS = 20 Adc, VGS = 0 Vdc,
dIS/dt = 100 A/ms) (Note 3)
Reverse Recovery Stored Charge
mC
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3. Pulse Test: Pulse Width ≤ 300 ms, Duty Cycle ≤ 2%.
4. Switching characteristics are independent of operating junction temperatures.
ORDERING INFORMATION
Package
Shipping†
DPAK
(Pb−Free)
75 Units / Rail
NTD20N06L−1G
IPAK (Straight Lead)
(Pb−Free)
75 Units / Rail
NTD20N06LT4G
DPAK
(Pb−Free)
2500 / Tape & Reel
NTDV20N06LT4G
DPAK
(Pb−Free)
2500 / Tape & Reel
Device
NTD20N06LG
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
2
NTD20N06L, NTDV20N06L
40
VGS = 10 V
VDS ≥ 10 V
8V
4.5 V
5V
30
ID, DRAIN CURRENT (AMPS)
ID, DRAIN CURRENT (AMPS)
40
6V
4V
20
3.5 V
10
30
20
TJ = 25°C
10
TJ = 100°C
3V
0
1
3
2
4
5
3.2
4
4.8
Figure 1. On−Region Characteristics
Figure 2. Transfer Characteristics
VGS = 5 V
TJ = 100°C
0.055
TJ = 25°C
0.045
0.035
TJ = −55°C
0.025
0
10
20
40
30
5.6
0.085
VGS = 10 V
0.075
0.065
0.055
TJ = 100°C
0.045
0.035
TJ = 25°C
0.025
TJ = −55°C
0.015
0
10
20
30
40
ID, DRAIN CURRENT (AMPS)
ID, DRAIN CURRENT (AMPS)
Figure 3. On−Resistance versus
Gate−to−Source Voltage
Figure 4. On−Resistance versus Drain Current
and Gate Voltage
10000
ID = 10 A
VGS = 5 V
IDSS, LEAKAGE (nA)
1.8
2.4
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
0.065
2
TJ = −55°C
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
0.075
0.015
0
1.6
RDS(on), DRAIN−TO−SOURCE RESISTANCE (W)
0.085
RDS(on), DRAIN−TO−SOURCE RESISTANCE
(NORMALIZED)
RDS(on), DRAIN−TO−SOURCE RESISTANCE (W)
0
1.6
VGS = 0 V
TJ = 150°C
1000
1.4
1.2
1
100
TJ = 100°C
0.8
0.6
−50 −25
0
25
50
75
100
125
150
175
10
0
10
20
30
40
50
TJ, JUNCTION TEMPERATURE (°C)
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
Figure 5. On−Resistance Variation with
Temperature
Figure 6. Drain−to−Source Leakage Current
versus Voltage
www.onsemi.com
3
60
NTD20N06L, NTDV20N06L
POWER MOSFET SWITCHING
The capacitance (Ciss) is read from the capacitance curve at
a voltage corresponding to the off−state condition when
calculating td(on) and is read at a voltage corresponding to the
on−state when calculating td(off).
At high switching speeds, parasitic circuit elements
complicate the analysis. The inductance of the MOSFET
source lead, inside the package and in the circuit wiring
which is common to both the drain and gate current paths,
produces a voltage at the source which reduces the gate drive
current. The voltage is determined by Ldi/dt, but since di/dt
is a function of drain current, the mathematical solution is
complex. The MOSFET output capacitance also
complicates the mathematics. And finally, MOSFETs have
finite internal gate resistance which effectively adds to the
resistance of the driving source, but the internal resistance
is difficult to measure and, consequently, is not specified.
The resistive switching time variation versus gate
resistance (Figure 9) shows how typical switching
performance is affected by the parasitic circuit elements. If
the parasitics were not present, the slope of the curves would
maintain a value of unity regardless of the switching speed.
The circuit used to obtain the data is constructed to minimize
common inductance in the drain and gate circuit loops and
is believed readily achievable with board mounted
components. Most power electronic loads are inductive; the
data in the figure is taken with a resistive load, which
approximates an optimally snubbed inductive load. Power
MOSFETs may be safely operated into an inductive load;
however, snubbing reduces switching losses.
Switching behavior is most easily modeled and predicted
by recognizing that the power MOSFET is charge
controlled. The lengths of various switching intervals (Dt)
are determined by how fast the FET input capacitance can
be charged by current from the generator.
The published capacitance data is difficult to use for
calculating rise and fall because drain−gate capacitance
varies greatly with applied voltage. Accordingly, gate
charge data is used. In most cases, a satisfactory estimate of
average input current (IG(AV)) can be made from a
rudimentary analysis of the drive circuit so that
t = Q/IG(AV)
During the rise and fall time interval when switching a
resistive load, VGS remains virtually constant at a level
known as the plateau voltage, VSGP. Therefore, rise and fall
times may be approximated by the following:
tr = Q2 x RG/(VGG − VGSP)
tf = Q2 x RG/VGSP
where
VGG = the gate drive voltage, which varies from zero to VGG
RG = the gate drive resistance
and Q2 and VGSP are read from the gate charge curve.
During the turn−on and turn−off delay times, gate current is
not constant. The simplest calculation uses appropriate
values from the capacitance curves in a standard equation for
voltage change in an RC network. The equations are:
td(on) = RG Ciss In [VGG/(VGG − VGSP)]
td(off) = RG Ciss In (VGG/VGSP)
2400
VDS = 0 V
VGS = 0 V
TJ = 25°C
C, CAPACITANCE (pF)
2000
Ciss
1600
1200
Crss
Ciss
800
400
0
Crss
10
5
VGS
0
VDS
10
5
15
Coss
20
25
GATE−TO−SOURCE OR DRAIN−TO−SOURCE VOLTAGE (VOLTS)
Figure 7. Capacitance Variation
www.onsemi.com
4
1000
6
VDS = 30 V
ID = 20 A
VGS = 5 V
QT
5
4
Q1
VGS
Q2
t, TIME (ns)
VGS , GATE−TO−SOURCE VOLTAGE (VOLTS)
NTD20N06L, NTDV20N06L
3
2
1
0
100
tr
tf
td(off)
10
td(on)
ID = 20 A
TJ = 25°C
0
16
4
8
12
QG, TOTAL GATE CHARGE (nC)
1
20
1
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
10
RG, GATE RESISTANCE (OHMS)
100
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
IS, SOURCE CURRENT (AMPS)
20
VGS = 0 V
TJ = 25°C
16
12
8
4
0
0.6
0.84
0.92
0.68
0.76
VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS)
1
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non−linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E−FETs can withstand the stress of
drain−to−source avalanche at currents up to rated pulsed
current (IDM), the energy rating is specified at rated
continuous current (ID), in accordance with industry custom.
The energy rating must be derated for temperature as shown
in the accompanying graph (Figure 12). Maximum energy at
currents below rated continuous ID can safely be assumed to
equal the values indicated.
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain−to−source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (TC) of 25°C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal Resistance −
General Data and Its Use.”
Switching between the off−state and the on−state may
traverse any load line provided neither rated peak current
(IDM) nor rated voltage (VDSS) is exceeded and the
transition time (tr,tf) do not exceed 10 ms. In addition the total
power averaged over a complete switching cycle must not
exceed (TJ(MAX) − TC)/(RqJC).
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
www.onsemi.com
5
NTD20N06L, NTDV20N06L
I D, DRAIN CURRENT (AMPS)
100
VGS = 15 V
SINGLE PULSE
TC = 25°C
10 ms
10
100 ms
1 ms
10 ms
1
dc
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
0.1
0.1
1
10
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
100
EAS , SINGLE PULSE DRAIN−TO−SOURCE
AVALANCHE ENERGY (mJ)
SAFE OPERATING AREA
140
ID = 16 A
120
100
80
60
40
20
0
25
Figure 11. Maximum Rated Forward Biased
Safe Operating Area
50
75
100
125
150
175
TJ, STARTING JUNCTION TEMPERATURE (°C)
Figure 12. Maximum Avalanche Energy versus
Starting Junction Temperature
10
R(t) (°C/W)
50% Duty Cycle
1
20%
10%
5%
0.1
2%
1%
Single Pulse
0.01
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
PULSE TIME (sec)
Figure 13. Thermal Response
di/dt
IS
trr
ta
tb
TIME
0.25 IS
tp
IS
Figure 14. Diode Reverse Recovery Waveform
www.onsemi.com
6
10
100
1000
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
IPAK
CASE 369D−01
ISSUE C
SCALE 1:1
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
E
R
4
Z
A
S
1
2
3
−T−
SEATING
PLANE
K
J
F
D
G
DATE 15 DEC 2010
H
3 PL
0.13 (0.005)
M
DIM
A
B
C
D
E
F
G
H
J
K
R
S
V
Z
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.090 BSC
0.034 0.040
0.018 0.023
0.350 0.380
0.180 0.215
0.025 0.040
0.035 0.050
0.155
−−−
MILLIMETERS
MIN
MAX
5.97
6.35
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
2.29 BSC
0.87
1.01
0.46
0.58
8.89
9.65
4.45
5.45
0.63
1.01
0.89
1.27
3.93
−−−
T
MARKING
DIAGRAMS
STYLE 1:
PIN 1. BASE
2. COLLECTOR
3. EMITTER
4. COLLECTOR
STYLE 2:
PIN 1. GATE
2. DRAIN
3. SOURCE
4. DRAIN
STYLE 5:
PIN 1. GATE
2. ANODE
3. CATHODE
4. ANODE
STYLE 6:
PIN 1. MT1
2. MT2
3. GATE
4. MT2
STYLE 3:
PIN 1. ANODE
2. CATHODE
3. ANODE
4. CATHODE
STYLE 4:
PIN 1. CATHODE
2. ANODE
3. GATE
4. ANODE
Discrete
YWW
xxxxxxxx
STYLE 7:
PIN 1. GATE
2. COLLECTOR
3. EMITTER
4. COLLECTOR
xxxxxxxxx
A
lL
Y
WW
DOCUMENT NUMBER:
DESCRIPTION:
98AON10528D
Integrated
Circuits
xxxxx
ALYWW
x
= Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
IPAK (DPAK INSERTION MOUNT)
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
DPAK (SINGLE GAUGE)
CASE 369C
ISSUE F
4
1 2
DATE 21 JUL 2015
3
SCALE 1:1
A
E
b3
C
A
B
c2
4
L3
Z
D
1
L4
2
3
NOTE 7
b2
e
c
SIDE VIEW
b
0.005 (0.13)
TOP VIEW
H
DETAIL A
M
BOTTOM VIEW
C
Z
H
L2
GAUGE
PLANE
C
L
L1
DETAIL A
Z
SEATING
PLANE
BOTTOM VIEW
A1
ALTERNATE
CONSTRUCTIONS
ROTATED 905 CW
STYLE 1:
PIN 1. BASE
2. COLLECTOR
3. EMITTER
4. COLLECTOR
STYLE 6:
PIN 1. MT1
2. MT2
3. GATE
4. MT2
STYLE 2:
PIN 1. GATE
2. DRAIN
3. SOURCE
4. DRAIN
STYLE 7:
PIN 1. GATE
2. COLLECTOR
3. EMITTER
4. COLLECTOR
STYLE 3:
PIN 1. ANODE
2. CATHODE
3. ANODE
4. CATHODE
STYLE 8:
PIN 1. N/C
2. CATHODE
3. ANODE
4. CATHODE
STYLE 4:
PIN 1. CATHODE
2. ANODE
3. GATE
4. ANODE
STYLE 9:
STYLE 10:
PIN 1. ANODE
PIN 1. CATHODE
2. CATHODE
2. ANODE
3. RESISTOR ADJUST
3. CATHODE
4. CATHODE
4. ANODE
SOLDERING FOOTPRINT*
6.20
0.244
2.58
0.102
5.80
0.228
INCHES
MIN
MAX
0.086 0.094
0.000 0.005
0.025 0.035
0.028 0.045
0.180 0.215
0.018 0.024
0.018 0.024
0.235 0.245
0.250 0.265
0.090 BSC
0.370 0.410
0.055 0.070
0.114 REF
0.020 BSC
0.035 0.050
−−− 0.040
0.155
−−−
MILLIMETERS
MIN
MAX
2.18
2.38
0.00
0.13
0.63
0.89
0.72
1.14
4.57
5.46
0.46
0.61
0.46
0.61
5.97
6.22
6.35
6.73
2.29 BSC
9.40 10.41
1.40
1.78
2.90 REF
0.51 BSC
0.89
1.27
−−−
1.01
3.93
−−−
GENERIC
MARKING DIAGRAM*
XXXXXXG
ALYWW
AYWW
XXX
XXXXXG
IC
Discrete
= Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
6.17
0.243
SCALE 3:1
DIM
A
A1
b
b2
b3
c
c2
D
E
e
H
L
L1
L2
L3
L4
Z
XXXXXX
A
L
Y
WW
G
3.00
0.118
1.60
0.063
STYLE 5:
PIN 1. GATE
2. ANODE
3. CATHODE
4. ANODE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. THERMAL PAD CONTOUR OPTIONAL WITHIN DIMENSIONS b3, L3 and Z.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL
NOT EXCEED 0.006 INCHES PER SIDE.
5. DIMENSIONS D AND E ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY.
6. DATUMS A AND B ARE DETERMINED AT DATUM
PLANE H.
7. OPTIONAL MOLD FEATURE.
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
DESCRIPTION:
98AON10527D
DPAK (SINGLE GAUGE)
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
onsemi and
are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative