BTR-7780-1590G

Optoway FEATURES l l l l l l l l l l l l l l BTR-7780-1590G 1 *********************************************************************************************************************************************************************** BTR-7780-1590G / BTR-7780-1590-SPG 1590 nm TX / 1510 nm RX , 3.3V / 1.25 Gb/s RoHS Compliant Single-Fiber Transceiver ********************************************************************************************************************************************************************** DESCRIPTION Single Fiber Bi-Directional Transceiver 1590 nm DFB LD Transmitter 1510 nm Receiver 24 dB Link Power Budget At Least Link distance up to 80 km Industry Standard 1 x 9 Footprint Single +3.3 V Power Supply RoHS Compliant 0 to 70oC Operating LVPECL Differential Inputs and Outputs LVPECL Signal Detect Output: BTR-7780-1590G LVTTL Signal Detect Output : BTR-7780C-1590G Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant The BTR-7780-1590G series is high performance module for single fiber communications by using 1590 nm DFB LD transmitter and 1510 nm receiver. A guaranteed minimum optical link budget of 24 dB is offered which can correspond to a link distance of over 80 km (assuming worst case fiber loss of 0.25 dB/km). The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated 1510 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l WDM 1.25 Gb/s Links l SONET/SDH Equipment Interconnect l Fiber Channel 1.063 Gb/s Links ORDER INFORMATION P/No. Bit Rate (Gb/s) 1.25 1.25 Distance (km) 80 80 TX (nm) 1590 DFB 1590 DFB RX (nm) 1510 1510 Voltage (V) 3.3 3.3 Package T emp (oC) 0 to 70 0 to 70 TX Power (dBm) 3 to -2 3 to -2 RX Sens. (dBm) -26 -26 Signal Detect TTL PECL R oHS Compliant Yes Yes BTR-7780C-1590G BTR-7780-1590G 1X9 1X9 Note: 1. BTR-XXXXXG is 1X9 SC receptacle type package. 2. BTR-XXXXX-APBBBG is 1X9 pigtail type package with different connector, A=S is SC connector, A=F is FC connector, A=T is ST connector, A=L is LC connector, A=M is MU connector; BBB is the length of fiber in cm. Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 0 GND 0 Max 85 70 250 4.5 Vcc 30 Units o C o C o C V V mA Notes 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Power Supply Current Symbol Vcc Topr Icc Min 3.13 0 Typ 3.3 1250 Max 3.47 70 1300 280 Units V o C Mb/s mA *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V2.0 Optoway Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V) Parameter Optical O ptical Transmit Power Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio E xtinction Ratio Output Eye O ptical Rise Time O ptical Fall Time R elative Intensity Noise T otal Jitter E lectrical D ata Input Current – Low D ata Input Current – High D ifferential Input Voltage D ata Input Voltage – Low D ata Input Voltage -- High Symbol Min Typ ------Max 3 1620 1 --0.26 0.26 -116 0.227 Units dBm nm nm dB dB ns ns dB/Hz ns µA µA mV V V Po -2 1580 λ --∆λ SMSR 30 ER 9.0 Compliant with IEEE 802.3z tr tf RIN TJ IIL IIH VIH - VIL VIL - VCC VIH - VCC -350 350 300 -2.0 -1.1 -1.58 -0.74 BTR-7780-1590G Notes 1 -20 dB Width 2 *********************************************************************************************************************************************************************** 20% to 80% Values 20% to 80% Values 2 3 3 Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. These inputs are compatible with 10K, 10KH and 100K ECL and LVPECL inputs. R eceiver Specifications (0oC < Topr < 70oC, 3.13 V < Vcc < 3. 47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation O ptical Return Loss E lectrical D ata Output Voltage – Low D ata Output Voltage – High SD Output Voltage -- Low SD Output Voltage -- High SD Output Voltage -- Low SD Output Voltage -- High Symbol --Pin Pa Pd Min ---3 ---40 1.0 1480 14 -2.0 -1.1 -2.0 -1.1 0 2.0 Typ ----------Max -26 ---26 --1520 Units dBm dBm dBm dBm dB nm dB V V V V V V Notes 1 Transition: low to high Transition: high to low 2 ORL V OL - VCC V OH - VCC V OL - VCC V OH - VCC VOL VOH -1.58 -0.74 -1.58 -0.74 0.8 Vcc+0.3 3 3 BTR-7780-1590G BTR-7780C-1590G Notes: 1. Minimum sensitivity and saturation levels at BER=1E-12 for a 2 7-1 PRBS. 2. At least 30 dB optical isolation for the wavelength 1580 to 1620 nm. 3. These outputs are compatible with 10K, 10KH and 100K ECL and LVPECL outputs. *************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V2.0 Optoway CONNECTION DIAGRAM Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data In Transmitter Signal Ground 1 (Rx GND) 2 (RD+) 3 (RD−) 4 (SD) 5 (Rx Vcc) 6 (Tx Vcc) 7 (TD−) 8 (TD+) 9 (Tx GND) N/C BTR-7780-1590G 3 *********************************************************************************************************************************************************************** TOP VIEW N/C PIN 1 2 3 4 5 6 7 8 9 Symbol Rx GND RD+ RD − SD Rx Vcc Tx Vcc TD − TD+ Tx GND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal +3.3V dc power for the receiver section +3.3V dc power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this plan to the trransmitter ground plane RECOMMENDED CIRCUIT SCHEMATIC Vcc3.3V Vcc3.3V R3 NA R2 NA C9 100nF C10 100nF L2 1uH Vcc3.3V MICROSTRIP5 Z=50R MICROSTRIP6 Z=5OR TD- Vcc3.3V LVPECL TD+ R4 NA R1 NA U2 TXGND TD+ TDTXVCC RXVCC SD RDRD+ RXGND BTR-77XX(C)/76XX(C) 9 8 7 6 5 4 3 2 1 C2 100nF L1 1uH PHY DEVICE C3 100nF C4 10uF C1 100nF C8 10uF RD+ Vcc3.3V C12 100nF R21 1K MICROSTRIP7 Z=50R MICROSTRIP8 R14 100R RD- LVPECL C11 100nF Z=5OR SD / LVPECL The split-load terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. *************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw h ttp: // www.optoway.com.tw 10/1/2005 V2.0 Optoway PACKAGE DIAGRAM Units in mm 1) Pigtail Type BTR-7780-1590G 4 *********************************************************************************************************************************************************************** BTR-7780-1590-SP50G N ote: Length L is 50± 3 cm. Other pigtail’s length is available upon request. 2 ) Receptacle Type BTR-7780-1590G Note: Specifications subject to change without notice. *************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V2.0