RS103S

Page No. : 1/1 RS103 Dual Operational Amplifier and Voltage Reference 8-Lead Plastic DIP-8 Package Code: P Description The RS103 is a monolithic IC that includes one independent op-amp and another op-amp for which the non inverting input is wired to a 2.5V fixed Voltage Reference. This device is offering space and cost saving in many applications like power supply management or data acquisition systems. • 8-Lead Plastic SOP-8 Package Code: S Operational Amplifier • Low input offset voltage: 0.5mV typ. • Low supply current: 350mA/op. (@ VCC = 5V) • Medium bandwidth (unity gain): 0.9MHz • Large output voltage swing: 0V to (VCC - 1.5V) • Input common mode voltage range includes ground • Wide power supply range: 3 to 32V ±1.5 to ±16V Operational Amplifier • Fixed output voltage reference 2.5V • 0.5% and 1% voltage precision • Sink current capability: 1 to 100mA • Typical output impedance: 0.2Ω Pin Configurations DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 2/2 Absolute Maximum Ratings Symbol VCC VID VI TJ TOPER Rthja Power Supply Voltage Input Differential Voltage Range Input Voltage Range Maximum Junction Temperature Operating Free-air Temperature Range Thermal Resistance Junction to Ambient (SO package) Parameter Range 36 36 -0.3 to +36 150 -55 to +125 175 Units V V V o C °C °C/W Electrical Characteristics Symbol ICC Parameter Power Supply Current Test Conditions VCC=30V, Ta=Thigh to Tlow VCC=5V, Ta=Thigh to Tlow RS103 Min Typ 1 0.6 Max 2 1.2 Unit mA mA Operator 2 (independent op-amp) VCC = +5V, VCC = Ground, Vo = 1.4V, Tamb = 25°C (unless otherwise specified) Symbol VIO DVIO IIO IIB AVD SVR CMR VICR VOH VOL ISource ISink ISC SR GBP THD Parameter Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Bias Current Large Signal Voltage Gain Supply Voltage Rejection Ratio Common-Mode Rejection Ratio Input Common Mode Voltage Range Output Voltage (High Limit) Output Voltage (Low Limit) Output Source Current Output Sink Current Output Short Circuit to Ground Slew Rate at Unity Gain Gain Bandwidth Product Total Harmonic Distortion Test Conditions Tamb = 25°C Tmin. ≤ Tamb ≤ Tmax. --Tmin. ≤ Tamb ≤ Tmax. Tmin. ≤ Tamb ≤ Tmax VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V. Tmin. ≤ Tamb ≤ Tmax. VCC = 5V to 30V Tmin. ≤ Tamb ≤ Tmax. VCC = +30V - see note 1) Tmin. ≤ Tamb ≤ Tmax. VCC=30V, RL=2KΩ VCC=30V, RL=10KΩ RL=10KΩ VCC = +15V, Vo = 2V, Vid = +1V VCC = +15V, Vo = 2V, Vid = -1V VCC=15V Vi = 0.5 to 3V, VCC = 15V RL = 2k, CL = 100pF, unity gain VCC = 30V,RL = 2k, CL = 100pF = 100kHz, Vin = 10mV f = 1kHz AV = 20dB,RL = 2k, VCC = 30V CL = 100pF, Vo = 2Vpp RS103 Min 25 65 65 26 27 20 10 0.2 0.5 Typ 2 7 35 100 100 85 27 28 5 40 20 40 0.4 0.9 0.02 Max 7 30 200 VCC-2V 20 60 Unit mV uV/oC nA nA V/mV dB dB V V mV mA mA mA V/us MHz % 1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC + - 1.5V. But either of both inputs can go to +36V without damage. DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 3/3 Operator 1 (op-amp with non-inverting input connected to the internal Vref) VCC+ = +5V, VCC- = Ground, Tamb = 25°C (unless otherwise specified) Symbol VIO DVIO IIB AVD SVR VOH VOL ISource ISink ISC SR GBP THD Parameter Input Offset Voltage Input Offset Voltage Drift Input Bias Current Large Signal Voltage Gain Supply Voltage Rejection Ratio Output Voltage (High Limit) Output Voltage (Low Limit) Output Source Current Output Sink Current Output Short Circuit to Ground Slew Rate at Unity Gain Gain Bandwidth Product Total Harmonic Distortion Test Conditions Tamb = 25°C Tmin. ≤ Tamb ≤ Tmax. --Tmin. ≤ Tamb ≤ Tmax Vicm = 0V VCC = 15V, RL = 2k Vicm = 0V VCC+ = 5V to 30V VCC=30V, RL=10KΩ RL=10KΩ VCC = +15V, Vo = 2V, Vid = +1V VCC = +15V, Vo = 2V, Vid = -1V VCC=15V Vi = 0.5 to 2V, VCC = 15V RL = 2k, CL = 100pF, unity gain VCC = 30V,RL = 2k, CL = 100pF = 100kHz, Vin = 10mV f = 1kHz AV = 20dB,RL = 2k, VCC = 30V CL = 100pF, Vo = 2Vpp RS103 Min 65 27 20 10 0.2 0.5 Typ 2 7 20 100 100 28 5 40 20 40 0.4 0.9 0.02 Max 7 20 60 Unit mV uV/oC nA V/mV dB V mV mA mA mA V/us MHz % Voltage Reference Symbol IK Cathode Current Parameter Value 1 to 100 Units mA Symbol VREF ΔVREF Imin |ZKA| Parameter Reference Input Voltage Reference Input Voltage Deviation Over Temperature Range Minimum Cathode Current for Regulation Dynamic Impedance - note 1) Test Conditions Tamb = 25°C Tmin. ≤ Tamb ≤ Tmax. VKA = Vref; Ik = 10mA Tmin. ≤ Tamb ≤ Tmax. VKA = VREF VKA = VREF, ΔIK = 1 to 100mA, f < 1kHz RS103 Min 2.48 Typ 2.5 7 0.5 0.2 Max 2.52 30 1 0.5 Unit V mV mA Ω 1. The dynamic impedance is defined as [ZKA| = ΔVKA/ΔIK DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 4/4 Operational Amplifiers DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 5/5 DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 6/6 DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 7/7 DIP-8 Dimension Marking: 8 7 6 5 DIM A B C D Control Code Min. 6.29 9.22 3.25 3.17 0.38 2.28 7.49 8.56 0.229 o 94 Max. 6.40 9.32 *1.52 *1.27 *0.99 3.35 3.55 0.53 2.79 7.74 *3.00 8.81 0.381 o 97 A 1 2 3 4 RS 103 Pin 1 Index Date Code P E F G H I J K L M B J F Note: Green label is used for pb-free packing C E D G H α1 K M L Material: • Lead solder plating: Sn60/Pb40 (Normal), Sn/3.0Ag/0.5Cu or Pure-Tin (Pb-free) • Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 I α1 8-Lead DIP-8 Plastic Package Package Code: P *: Typical, Unit: mm SOP-8 Dimension A G Marking: DIM A B C D E F G H I J K L M N O Min. 4.85 3.85 5.80 1.22 0.37 3.74 1.45 4.80 0.05 0.30 0.19 0.37 0.23 0.08 0.00 Max. 5.10 3.95 6.20 1.32 0.47 3.88 1.65 5.10 0.20 0.70 0.25 0.52 0.28 0.13 0.15 8 B 7 6 5 C 4 J H I Pin 1 Index Date Code RS 103 S Control Code Pin1 Index 2 3 Note: Green label is used for pb-free packing Material: • Lead solder plating: Sn60/Pb40 (Normal), Sn/3.0Ag/0.5Cu or Pure-Tin (Pb-free) • Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 D E Part A K L N O Part A M *: Typical, Unit: mm F 8-Lead SOP-8 Plastic Surface Mounted Package Package Code: S Ordering Information PART NUMBER RS103P RS103S PIN-PACKAGE DIP-8 SOP-8 DS-RS103-01 Nov, 2007 www.Orister.com Page No. : 8/8 Soldering Methods for Orister’s Products 1. Storage environment: Temperature=10oC~35oC Humidity=65%±15% 2. Reflow soldering of surface-mount devices Figure 1: Temperature profile tP TP Ramp-up TL Tsmax Temperature tL Critical Zone TL to TP Tsmin tS Preheat Ramp-down 25 t 25oC to Peak Time Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Tsmax to TL - Ramp-up Rate Time maintained above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Time within 5oC of actual Peak Temperature (tP) Ramp-down Rate Time 25oC to Peak Temperature 3. Flow (wave) soldering (solder dipping) Products Pb devices. Pb-Free devices. Sn-Pb Eutectic Assembly